焙烧及还原温度对 Co-Pt-ZrO2/γ-Al2O3催化剂费托合成反应性能的影响

采用浸渍法制备了Co-Pt-ZrO₂/γ-Al₂O₃催化剂,对其进行了BET、XRD和TPR等表征,并在浆态床反应器上考察了焙烧温度和还原温度对催化剂费托合成反应性能的影响。结果表明,焙烧温度过高,容易造成Co物种和载体间的相互作用增强,使部分氧化钴颗粒聚集或烧结,导致催化剂的F-T合成反应活性和C₅₊烃选择性降低。还原温度较低时,钴物种不能充分还原,CO加氢活性低,甲烷选择性高,重质烃选择性低;还原温度过高,则可能造成活性物种的烧结,反而降低了催化剂的活性和重质烃选择性。在原料气n(H₂)/n(CO)=2.0、483 K、2.4 MPa和空速3.6 L/(gcat·h)的条件下,31.08%Co～0.11%Pt～7.16%ZrO₂/Al₂O₃催化剂在673 K焙烧。纯H₂下653 K还原后,其费托性能最佳;CO转化率为27.0%,C₅₊的选择性为83.0%。     

焙烧温度对CuO/γ-Al2O3和CeO2-CuO/γ-Al2O3催化剂NO还原活性的影响

用浸渍法制备了CuO/γ-Al2O3催化剂和CeO2改性的CeO2-CuO/γ-Al2O3催化剂,考察了焙烧温度对CuO/γ-Al2O3和CeO2-CuO/γ-Al2O3催化剂C3H6还原NO反应活性的影响,以及CeO2的添加量对CeO2-CuO/γ-Al2O3催化剂C3H6还原NO反应活性的影响。结果表明,在200 ℃～500 ℃的焙烧温度范围内,焙烧温度对CuO/γ-Al2O3催化剂的活性影响很小；在500 ℃～800 ℃的焙烧温度范围内,随着焙烧温度的升高CuO/γ-Al2O3催化剂的活性急剧下降,由XRD物相测定结果可知,归因于对反应表现惰性的尖晶石CuAl2O4相的生成。当焙烧温度为500 ℃时,CeO2的添加对CuO/γ-Al2O3催化剂的活性影响很小；当焙烧温度为800 ℃时,CeO2的添加对CuO/γ-Al2O3催化剂有明显的助催化作用,当Ce和Cu的摩尔比为1∶10时,NO转化率较为理想。     

In situ carbon nanotube synthesis by the reduction of NiO/γ-Al2O3 catalyst in methane

The synthesis of carbon nanotubes (CNTs) via chemical vapour deposition of methane on NiO/γ-Al2O3 catalyst has been investigated. The reduction behavior of NiO/γ-Al2O3 by methane was studied using thermogravimetric (TG) and X-ray diffraction (XRD) techniques. It was found that the NiO supported on γ-Al2O3, was reduced to Ni⁰ in methane atmosphere in the temperature range of 710--770 ℃. The catalytic activity of NiO/γ-Al2O3 for CNTs synthesis by in situ chemical vapour deposition of methane during the reduction was also investigated. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to observe the CNTs produced at various reduction temperatures. The results indicated that the reduction temperature exhibits obvious influence on the morphology and the yield of CNTs. CNTs with the diameter of about 20 nm were obtained at reduction temperature of 750 ℃, and higher reduction temperature (such as 800 and 850 ℃) led to an increase in CNTs diameter and a decrease in CNTs yield.     

Environment-friendly synthesis of N-phenylpiperidine from aniline and 1,5-pentanediol over γ-Al2O3 catalyst

An efficient environment-friendly synthesis of N-phenylpiperidine was developed from aniline and 1,5-pentanediol over γ-Al2O3 catalyst under atmospheric pressure. The conversion of 1,5-pentanediol reached 97% and the selectivity for N-phenylpiperidine attained 94%. The structure of the catalyst was characterized by NH3-TPD and BET. The influences of calcination temperature of the catalyst and reaction temperature on activity and selectivity of the catalyst were investigated.     

ZrO2在Rh/γ-Al2O3催化剂中对NO催化还原反应的作用

测定了含ZrO2的Rh/γ-Al2O3催化剂上NO+C2H4和NO+C2H4+O2的反应活性,并应用TPR、XRD、BET比表面等表征了ZrO2的加入方式和晶型对Rh/γ-Al2O3催化剂活性和结构的影响。结果表明,ZrO2的加入一定程度地抑制了Rh3+与γ-Al2O3之间的相互作用和γ-Al2O3的相变,提高了催化剂的热稳定性,明显提高了850℃老化样品的NO+C2H4反应活性。对于NO+C2H4+O2反应,含ZrO2样品的选择还原活性却较低,表明反应机理不同,而且ZrO2对C2H4的深度氧化有促进作用,但老化后活性下降幅度比不含ZrO2的样品小。     

助剂Cu对Ni/γ-Al2O3催化剂低温还原性能影响

制备了一系列铜质量分数不同的CuNi/γ-Al2O3催化剂,进行了TPR和XRD表征并测定了该系列催化剂对苯加氢制环己烷的催化活性。结果表明,助剂Cu的负载量对低温（160 ℃）还原后催化剂的催化活性影响很大,在铜镍原子摩尔比为1∶1时,催化剂具有较高的催化活性和稳定性;添加铜组分可促进镍在载体表面分散,使负载NiO的还原温度降低,催化活性提高。     

CuO/γ-Al2O3脱除烟气中SO2的研究

将CuO/γ-Al2O3用于烟气脱硫研究。考查了脱硫剂制备参数及反应条件对CuO/γ-Al2O3脱硫活性的影响。并对不同载铜量的脱硫剂进行了XRD表征。结果表明，载铜量的质量分数为8%～10%时，脱硫剂具有较高的脱硫活性，高于10%的载铜量致使活性组分CuO在Al2O3表面发生多层覆盖，活性位的利用率下降；在350 ℃～500 ℃的烟气温度及 3 000 L/kg·h～56 000 L/kg·h的操作空速范围内，CuO/γ-Al2O3具有较高的脱硫活性，烟气中的O2对于CuO/γ-Al2O3的脱硫活性是必需的，水的影响不大。     

异丁烷脱氢V2O5/γ-Al2O3催化剂的研究

五氧化二钒;异丁烷脱氢V2O5/γ-Al2O3催化剂的研究     

助剂对Pd/γ-Al2 O3催化剂上NO选择催化还原的影响

研究了含氧条件下钯催化剂上进行丙烯选择催化还原NO的反应,考察浸渍法制备的Pd/γ-Al2O3催化剂中加入碱(土)金属或稀土氧化物助剂对NO转化率的影响,并对催化剂进行了XRD表征及在氧化气氛中饱和吸附NO后的TPD研究.结果表明,助剂CeO2、 Li2O能较大幅度提高催化剂的低温活性,使NO的最高转化率增加1～3.5倍.Pd/CeO2-Al2O3、 Pd/Li2O-Al2O3催化剂有较高的Pd分散度及较强的NO解离吸附能力.并讨论了NO、 N2O、 NO2-和NO3-等吸附态物种在催化剂表面的形成及脱附特性对催化剂选择催化还原NO性能的影响.     

A Novel Way to Prepare γ-Al2O3 Supported SO42-/ZrO2 Solid Superacid Catalysts for n-Butane Isomerization

Highly active solid superacid catalysts for n-butane isomerization, SZ/Al2O3-P, were prepared by supporting SO42-/ZrO2 (SZ) on γ-Al2O3 carrier using a precipitation method.The activities of some catalysts were enhanced significantly.The activity of the most active sample, 60%SZ/Al2O3-P, was even about 2 times more active than that of the SZ catalyst.     

Study of CO2 Hydrogenation to Methanol over Cu-V/γ-Al2O3 Catalyst

The effect of vanadium addition to CU/γ-Al2O3 catalyst used in the hydrogenation of CO2 to produce methanol was studied. It was found that the catalytic performance of the Cu-based catalyst improved after V addition. The influence of reaction temperature, space velocity and the molar ratio of H2 to CO2 on the performance of 12%Cu-6%V/γ-Al2O3 catalyst were also studied. The results indicated that the best conditions for reaction were as follows: 240℃, 3600 h-1 and a molar ratio of H2 to CO2 of 3:1. The results of XRD and TPR characterization demonstrated that the addition of V enhanced the dispersion of the supported CuO species, which resulted in the enhanced catalytic performance of CU-V/γ-Al2O3 binary catalyst.     

K-MoO3/γ-Al2O3催化剂表面物种状态、组成和性能

应用XPS、XRD、ESR 和TPR技术分析了KCl助剂含量变化对MoO_3/γ-Al_2O_3催化剂表面物种状态、组成及其硫化还原性能的影响. K/Mo比小于0.8时, 钾离子完全和钼作用, 形成钾钼作用物种, 催化剂硫化后发生K~+表面富集, Cl~-游离并流失; K/Mo比0.8时, 钾钼作用达到饱和; K/Mo比大于0.8时, 多余的K~+和Cl~-结合以体相KCl形式存在. 钾钼作用减弱了Mo(Ⅵ)和载体之间的作用, 部分抑制了Mo(Ⅵ)的硫化还原. 钾钼作用物种硫化后可能产生CO合成醇的活性中心.     

Surface Acidity/Basicity and Catalytic Reactivity of CeO2/7-Al2O3 Catalysts for the Oxidative Dehydrogenation of Ethane with Carbon Dioxide to Ethylene

Dehydrogenation of ethane to ethylene in CO2 was investigated over CeO2/γ-Al2O3 catalysts at 700℃ in a conventional flow reactor operating at atmospheric pressure. XRD, BET and microcalori-metric adsorption techniques were used to characterize the structure and surface acidity/basicity of the CeO2/γ-Al2O3 catalysts. The results show that the surface acidity decreased while the surface basicity increased after the addition of CeO2 to γ-A12O3. Accordingly, the activity of the hydrogenation reaction of CO2 increased, which might be responsible for the enhanced conversion in the dehydrogenation of ethane to ethylene. The highest ethane conversion obtained was about 15% for the 25%CeO2/γ-Al2O3. The selectivity to ethylene was high for all the CeO2,γ-A12O3 and CeO2/γ-Al2O3 catalysts.     

CuO/Mn2O3 /γ-Al2O3催化剂的制备、表征及其在CO氧化反应中的性能研究

采用浸渍法在γ-Al2O3载体上分步负载改性剂Mn2O3和活性组分CuO,制备了一系列不同配比的CuO/Mn2O3/γ-Al2O3催化剂,并运用CO+O2模型反应、XRF、XRD、H2-TPR、in-situ FTIR等手段表征了催化剂的活性和物理化学性质。活性测试结果表明,锰氧化物对γ-Al2O3载体的改性能有效地提高CuO/γ-Al2O3催化剂在CO+O2模型反应中的催化活性。XRD结果表明,锰氧化物对γ-Al2O3载体的改性可以促进氧化铜在载体表面的分散,从而提高了分散态氧化铜的含量,不过这与活性变化的趋势并不完全一致。进一步结合H2-TPR、in-situ FTIR表征结果 ,我们发现,分散态铜、锰氧化物的还原性质也是影响其催化活性的重要因素,催化剂中分散态铜、锰物种越容易被还原,其对CO+O2模型反应的催化活性就越高。     

CeO2-MOx（M=La^3＋,Ca^2＋）改性Pd/γ-Al2O3催化甲烷燃烧性能

采用沉积-沉淀法制备了固溶体CeO2-MOx=(M=La3+,Ca2+)改性的Pd/γ-Al2O3催化剂,利用XRD、Raman和XPS对催化剂进行了表征.结果表明,金属(M)离子进入CeO2的晶格,形成CeO2-MOx固溶体,Raman谱上463cm-1处对应于Ce-O键的F2g对称伸缩振动强度降低.其中,样品Pd/γ-Al2O3CeO2-CaO在615 cm-1处出现一小峰,样品Pd/γ-Al2O3-CeO2-La2O3在320cm-1处出现的肩峰,都表明固溶体CeO2-MOx的形成使O2-亚晶格结构对称性降低.XPS分析表明,固溶体改性的Pd/γ-Al2O3催化剂中Pd的3d5/2结合能比正常价态的PdO的结合能高出0.5-0.6 eV,形成了一种高度离子化的.与载体具有强相互作用的Pd物种.催化甲烷燃烧实验证明,固溶体CeO2-MOx(M=La3+,Ca2+)改性的Pd/γ-Al2O3催化剂的低温活性和稳定性均高于未经改性的Pd/γ-Al2O3催化剂和仅用CeO2改性的Pd/γAl2O3催化剂,在空速为50000 h-1时,可使1%CH4-99%空气(体积分数)混合气中甲烷的10%转化温度降至254℃,转化率100%时的转化温度降至340℃.     

V2O5/γ-Al2O3和V2O5/SiO2负载型催化剂对异丁烷的催化脱氢性能

V2O5/γ-Al2O3和V2O5/SiO2负载型催化剂对异丁烷的催化脱氢性能;V2O5/γ-Al2O3; V2O5/SiO2; 异丁烷; 脱氢     

Metathesis of Butylene-2 and Ethylene to Propylene over 3.0Mo／（Hβ＋γ-Al2O3） Catalysts with Different γ-Al2O3 Contents

A series of 3. OMo/(Hβ γ-Al2O3) samples with γ-Al2O3 contents in the range of 0-100% (mass fraction) was studied by means of XRD, NH3-TPD, TPR and BET determinations for characterizing their structures. The Hβ zeolite structure in the 3.0Mo/Hβ sample can be effectively stabilized by adding some γ-Al2O3 to Hβ zeolite. γ-Al2O3 mainly favors the formation of polymolybdate or multilayered Mo oxide, while Hβ mainly forms the Al2(MoO4)3 species, as evaluated by the TPR technique. When used as the catalyst for the metathesis of butylene-2 and ethylene to propylene, there exists a close correlation between the specific surface area and stability of the catalyst. The specific surface area of the catalyst shows the maximum when (Hβ γ-Al2O3) contains 30%γ-Al2O3, which is in agreement with that of the time needed for the reaction stablization. In the case of maximum surface area, the rate of coke deposition is the minimum.     

溶剂热合成具有纳米孔结构的γ-Al2O3

0引言γ-Al2O3又称活性氧化铝,一般具有较高的比表面积,在工业生产中被广泛用作吸附剂和催化剂载体[1],尤其是可作为负载贵金属催化剂的载体[2￣4]。纳米级的γ-Al2O3由于颗粒粒径小而在其颗粒表面形成了丰富的失配键和欠氧键,以此制成多孔薄膜作为催化剂及催化剂载体,其性能比目前使用的同类产品性能要优越许多[5]。但纳米级的γ-Al2O3也存在一些缺点,如由于纳米颗粒的表面能较高导致了颗粒的团聚较严重,分散性较差;由于γ-Al2O3活性较高,所以其高温热稳定性不太好,这些缺点极大地限制了γ-Al2O3的应用范围。因此合成具有良好分散性和…     

Theoretical studies of adsorption property on Ir_4/MgO and Ir_4/γ-Al_2O_3

The adsorption properties of atomic and molecular species on Ir4/MgO and Ir4/γ-Al2O3 have been systematically studied by means of planewave density functional theory(DFT)calculations using the periodic boundary conditions.The binding energies of these species were ordered as follows:H2O相似文献   

Effect of surface structure on the catalytic behavior of Ni：Cu/Al and Ni：Cu：K/Al catalysts for methane decomposition

Methane decomposition using nickel, copper, and aluminum （Ni：Cu/Al） and nickel, copper, potassium, and aluminum （Ni：Cu：K/Al） modified nano catalysts has been investigated for carbon fibers, hydrogen and hydrocarbon production. X-ray photoelectron spectroscopy （XPS）, static secondary ion mass spectrometry （SSIMS）, thermal gravimetric analysis （TGA）, Fourier transform infrared （FT-IR）, secondary electron microscopy/X-ray energy dispersive （SEM-EDX）, and temperature programmed desorption （TPD） were used to depict the chemistry of the catalytic results. These techniques revealed the changes in surface morphology and structure of Ni, Cu, Al, and K, and formation of bimetallic and trimetallic surface cationic sites with different cationic species, which resulted in the production of graphitic form of pure carbon on Ni：Cu/Al catalyst. The addition of K has a marked effect on the product selectivity and reactivity of the catalyst system. K addition restricts the formation of carbon on the surface and increases the production of hydrogen and C2, C3 hydrocarbons during the catalytic reaction whereas no hydrocarbons are produced on the sample without K. This study completely maps the modified surface structure and its relationship with the catalytic behavior of both systems. The process provides a flexible route for the production of carbon fibers and hydrogen on Ni：Cu/Al catalyst and hydrogen along with hydrocarbons on Ni：Cu：K/Al catalyst. The produced carbon fibers are imaged using a transmission electron microscope （TEM） for diameter size and wall structure determination. Hydrogen produced is COx free, which can be used directly in the fuel cell system. The effect of the addition of Cu and its transformation and interaction with Ni and K is responsible for the production of CO/CO2 free hydrogen, thus producing an environmental friendly clean energy.