Coadsorption of CO and C6H6 on Co(0 0 0 1)

We have studied the influence of CO on the adsorption of benzene on the Co(0 0 0 1) surface using LEED, XPS, TDS and work function measurements. CO was found to reduce the benzene adsorption, but even at saturation CO exposure no complete blocking was observed. Thermal desorption of the coadsorbed layer featured CO and H₂ peaks indicating partial dehydrogenation of benzene and retaining of the CO bond. Ordered LEED structures were found with all coverages: Pre-adsorption of CO led to patterns already seen for pure carbon monoxide adsorption. Pre-adsorption of benzene showed the known structure of pure benzene also with small CO exposures, but higher CO exposures yielded a mixture of and patterns.     

Aromatic interactions in the close packing of phenyl-imides at Cu(1 1 0) surfaces

The oxidation of aniline at Cu(1 1 0) surfaces at 290 K has been studied by XPS and STM. A single chemisorbed product, assigned to a phenyl imide (C₆H₅N(a)), is formed together with water which desorbs. Reaction with preadsorbed oxygen results in a maximum surface concentration of phenyl imide of 2.8 × 10¹⁴ mol cm⁻² and a surface dominated by domains of three structures described by , and unit meshes. However, concentrations of phenyl imide of up to 3.3 × 10¹⁴ mol cm⁻² were obtained from the coadsorption of aniline and dioxygen (300:1 mixture) resulting in a highly ordered biphasic structure with and domains. Comparison of the STM and XPS data shows that only half the phenyl imides at the surface are imaged. Pi-stacking of the phenyl rings is proposed to account for this observation.     

Adsorption structure of germanium on the Ru(0 0 0 1) surface

Coverage-dependent adsorption energy of the Ge/Ru(0 0 0 1) growth system and the geometrical distortions of the most stable adsorption structure are investigated through first-principles calculations within density functional theory. A local minimum in adsorption energy is found to be at a Ge coverage of 1/7 monolayer with a Ru(0 0 0 1)- symmetry. Based on this stale superstructure, the scanning tunneling microscopy (STM) and scanning tunneling spectroscopy (STS) images are simulated by means of surface local-density of states (LDOS). The results are consistent well with the STM measurements on the phase for Ge overlayer on Ru(0 0 0 1). From this stimulation, the relations between the STM images and the lattice distortion are also clarified.     

The local adsorption geometry and electronic structure of alanine on Cu{1 1 0}

The adsorption of alanine on Cu{1 1 0} was studied by a combination of near edge X-ray absorption fine structure (NEXAFS) spectroscopy, X-ray photoelectron spectroscopy (XPS) and density functional theory (DFT). Large chemical shifts in the C 1s, N 1s, and O 1s XP spectra were found between the alanine multilayer and the chemisorbed and pseudo-(3 × 2) alaninate layers. From C, N, and O K-shell NEXAFS spectra the tilt angles of the carboxylate group (≈26° in plane with respect to and ≈45° out of plane) and the C-N bond angle with respect to could be determined for the pseudo-(3 × 2) overlayer. Using this information three adsorption geometries could be eliminated from five p(3 × 2) structures which lead to almost identical heats of adsorption in the DFT calculations between 1.40 and 1.47 eV/molecule. Due to the small energy difference between the remaining two structures it is not unlikely that these coexist on the surface at room temperature.     

Co-induced nano-structures on Si(1 1 1) surface

The interaction of cobalt atoms with silicon (1 1 1) surface has been investigated by means of scanning tunneling microscopy (STM) and low-energy electron diffraction (LEED). Besides the Co silicide islands, we have successfully distinguished two inequivalent Co-induced reconstructions on Si(1 1 1) surface. Our high-resolution STM images provide some structural properties of the two different derived phases. Both of the two phases seem to form islands with single domain. The new findings will help us to understand the early stage of Co silicide formations.     

Photoelectron spectroscopy study of Pb/Ag(1 1 1) in the submonolayer range

The vacuum deposition of Pb onto Ag(1 1 1) gives rise to two different surface structures depending on coverage and deposition temperature. At room temperature (RT), low energy electron diffraction (LEED) reveals a sharp reconstruction completed at 1/3 Pb monolayer (ML). Beyond, a close-packed Pb(1 1 1) incommensurate overlayer develops. At low temperature (LT, ∼100 K) the incommensurate structure is directly observed whatever the coverage, corresponding to the growth of close-packed two-dimensional Pb(1 1 1) islands. Synchrotron radiation Pb 5d core-level spectra clearly demonstrate that in each surface structure all Pb atoms have essentially a unique, but different, environment. This reflects the surface alloy formation between the two immiscible metals in the reconstruction and a clear signature of the de-alloying process at RT beyond 1/3 ML coverage.     

Sapphire (0 0 0 1) surface modifications induced by long-pulse 1054 nm laser irradiation

We have investigated modifications of sapphire (0 0 0 1) surface with and without coating, induced by a single laser pulse with a 1054 nm wavelength, 2.2 s duration, 7.75 mm spot and energy of 20-110 J. A holographic optical element was used for smoothing the drive beam spatially, but it induced small hotspots which initiated damage on the uncoated and coated surfaces. The individual damage effects of hotspots became less pronounced at high fluences. Due to high temperature and elevated non-hydrostatic stresses upon laser irradiation, damage occurred as fracture, spallation, basal and rhombohedral twinning, melting, vitrification, the formation of nanocrystalline phases, and solid-solid phase transition. The extent of damage increased with laser fluences. The formation of regular linear patterns with three-fold symmetry ( directions) upon fracture was due to rhombohedral twinning. Nanocrystalline -Al₂O₃ formed possibly from vapor deposition on the coated surface and manifested linear, triangular and spiral growth patterns. Glass and minor amounts of -Al₂O₃ also formed from rapid quenching of the melt on this side. The - to -Al₂O₃ transition was observed on the uncoated surface in some partially spalled alumina, presumably caused by shearing. The nominal threshold for laser-induced damage is about 47 J cm⁻² for these laser pulses, and it is about 94 J cm⁻² at the hotspots.     

Electronic structure of the Sb-induced Si(1 1 3)2 × 5 surface

The surface electronic structure of Sb/Si(1 1 3)2 × 5 was investigated by angle-resolved photoemission spectroscopy experiments. This reveals Sb/Si(1 1 3)2 × 5 to have three surface bands with anisotropic two-dimensional characteristics. The band widths of the surface bands along is larger than along . The number of surface bands of Sb/Si(1 1 3)2 × 5 and their band dispersions along and are quite analogous with those of Sb/Si(1 1 3)2 × 2 composed of Sb adatom and Si tetramer chains. The electronic structure analogy suggests that Sb/Si(1 1 3)2 × 5 and Sb/Si(1 1 3)2 × 2 have common building blocks such as Sb adatom and Si tetramer chains.     

Reversible electromigration of thallium adatoms on the Si(1 1 1) surface

By means of low-energy electron diffraction (LEED), we found a reversible structural change of on thallium (Tl) adsorbed Si(1 1 1) surfaces by switching the polarity of applied DC voltage for heating the sample. It was shown in the literature that Tl adatoms are located on the T₄ sites of the bulk-terminated surface both in the (1 × 1) and . It is clarified that the structural change is caused by the electromigration of the Tl adatoms. Tl atoms migrate towards the cathode, being induced by the electric field (10-20 V/cm). We discussed an atomic process of the electromigration.     

Surface phase diagram and temperature induced phase transitions of Sn/Cu(1 0 0)

Room temperature deposition of Sn on Cu(1 0 0) gives rise to a rich variety of surface reconstructions in the submonolayer coverage range. In this work, we report a detailed investigation on the phases appearing and their temperature stability range by using low-energy electron diffraction and surface X-ray diffraction. Previously reported reconstructions in the submonolayer range are p(2 × 2) (for 0.2 ML), p(2 × 6) (for 0.33 ML), ()R45° (for 0.5 ML), and c(4 × 4) (for 0.65 ML). We find a new phase with a structure for a coverage of 0.45 ML. Furthermore, we analyze the temperature stability of all phases. We find that two phases exhibit a temperature induced reversible phase transition: the ()R45° phase becomes ()R45° phase above 360 K, and the new phase becomes p(2 × 2) also above 360 K. The origin of these two-phase transitions is discussed.     

A novel approach to measure the step line tension and the step dipole moment on vicinal Au(0 0 1) electrodes

In this paper we introduce a new experimental approach to determine the potential dependence of the step line tension on metal electrodes in contact with an electrolyte: (0 0 1) and (1 1 n) surfaces of single crystal gold electrodes were investigated by impedance spectroscopy in solutions containing weakly adsorbing anions, such as , F⁻ and . Within the limits of error the shift in the potential of zero charge is proportional to the step density of the vicinal surfaces indicative of a well-defined dipole moment per step length. The dipole moments per step atom are 6.8 ± 0.8, 5.2 ± 0.4, 5.8 ± 0.5 × 10⁻³ eÅ for , , and F⁻ containing electrolytes, respectively. Using the values for the pzc and the potential dependence of the capacitance curves, the potential dependence of the surface tension of the vicinal surfaces is determined. The line tension of the steps is then calculated from the difference between the surface tension of the stepped and the step free surface. Our results represent the first experimental confirmation of a recent theoretical model proposing that in absence of specifically adsorbed ions the step line tension should decrease (roughly linear) with potential.     

STM study of l-serine adsorption on Cu(0 0 1)

The adsorption of l-serine on Cu(0 0 1) surface at 310 K was studied by scanning tunneling microscope (STM). l-serine molecules on the Cu(0 0 1) initially formed a domain of thick lines with a order structure along the direction on the terraces regardless of the coverage of serine. The thick lines were partly replaced by thin line along the direction, and completely disappeared in 2 h. It is considered that in these structures hydrogen bonds involved in hydroxymethyl group between adsorbates play some role in addition to intermolecular hydrogen bond between a hydrogen atom of amino group and an oxygen atom of carboxy group for alanine adsorption.     

Au-induced nanofaceting and the stoichiometry of the Si(7 7 5)-Au surface

The Au-induced changes in the surface morphology of a Si(1 1 1) sample miscut 8° towards have been measured using room temperature scanning tunneling microscopy and low energy electron diffraction. Au coverages of less than 0.06 ML up to 0.43 ML have been investigated. In all cases Au adsorption produces dramatic changes in surface morphology. The Au-induced surface exhibits nanofacets with orientations that depend critically on the amount of Au deposited. Below 0.32 ML, the restructured surface always includes (7 7 5)-Au nanofacets suggesting that the (7 7 5)-Au facet is energetically preferred on this surface. The (7 7 5)-Au facet is oriented 8.5° from [1 1 1] towards and is characterized by 1-d chains spaced 21.3 Å apart that run along the direction. By maximizing the surface area of the (7 7 5) facets and optimizing the associated diffraction pattern we determine that the (7 7 5)-Au reconstruction is optimized at 0.24 ML and corresponds to a stoichiometry of 1.5 Au atoms per 1 × 1 unit cell. We believe that the local Au coverage on the (7 7 5) facet is 0.24 ML, and that the deficit/extra of Au at any particular coverage is accommodated by non-(7 7 5) facets. For example at 0.06 ML the regions of step bunching observed on the clean surface are eliminated and Au-induced (7 7 5) and Au-free (1 1 1)7 × 7 facets are already visible. Up to 0.18 ML the non-(7 7 5) facet is Au free. Beyond 0.32 ML, the (7 7 5)-Au reconstruction is no longer stable and the extra Au is accommodated by the formation of higher angle facets with smaller chain spacings.