Determination of a (4 × 4) structure formed on a Cu(0 0 1) surface by adsorption of calcium

The adsorption of calcium (Ca) atoms on a Cu(0 0 1) surface has been studied by low-energy electron diffraction (LEED) at 130, 300 and 400 K. It is found that a (4 × 4) was the only LEED pattern appeared at 400 K while a quasi-hexagonal structure was formed in a wide range of submonolayer coverage at 130 K. At 300 K, the (4 × 4) LEED spots were broad and weak. The (4 × 4) structure formed at 400 K was determined by a tensor LEED I-V analysis. It is a new-type of surface alloys consisting of five substitutional Ca atoms, nine surface Cu atoms, and two atomic vacancies in the unit cell. In spite of a quite large size-difference between Ca (3.94 Å) and Cu (2.55 Å) atoms, all Ca atoms are located at the substitutional sites. Among surface alloys so far reported, the atomic size ratio between Cu and Ca in the (4 × 4), 1.54, is the largest. Optimized structural parameters reveal that large lateral displacements of surface Cu atoms, being enabled by the appearance of the vacancies, allow the formation of the (4 × 4) structure.     

Vibrational entropy-driven dealloying of Mo(1 0 0) and W(1 0 0) surface alloys

The formation and stability of Cu, Ag and Au-induced c(2 × 2) alloys at the Mo(1 0 0) and W(1 0 0) surfaces have been investigated with low-energy electron microscopy and diffraction. The ordered alloys transform to disordered overlayer structures at elevated temperature. Comparison of the transformation temperatures with energetics obtained from first principles calculations reveals the vibrational entropic contribution to the system free energy that defines alloy thermal stability. Effective Debye temperatures for metal adatoms are determined that exhibit the expected mass and bond strength dependence.     

Realization of an atomic sieve: Silica on Mo(1 1 2)

The adsorption of Pd, Ag and Au atoms on a porous silica film on Mo(1 1 2) is investigated by scanning tunneling microscopy and density functional theory. While Pd atoms are able to penetrate the holes in the silica top-layer with virtually no barrier, Ag atoms experience an intermediate barrier value and Au atoms are completely unable to pass the oxide surface. The penetration probability does not correlate with the effective size of the atoms, but depends on their electronic structure. Whereas Pd with an unoccupied valence s-orbital has a low penetration barrier, Ag and Au atoms with occupied s-states experience a substantial repulsion with the filled oxide states, leading to a higher barrier for penetration. In the case of Ag, the barrier height can be temporally lowered by promoting the Ag 5s-electron into the support. The Mo-supported silica film can thus be considered as a primitive form of an atomic sieve whose selectivity is controlled by the electronic structure of the adatoms.     

Structure and reactivity of Pd doped Ag surfaces

We have performed first principles calculations for clean and Pd doped Ag(1 1 1) and Ag(1 0 0) surfaces, with and without adsorbed O and CO. Our results for the structure of the Pd doped Ag surfaces indicate that Pd atoms are located lower than the surrounding Ag surface atoms. We find that O atoms adsorbed on Pd doped Ag(1 1 1) reside at the fcc hollow sites, the site next to Pd being slightly favored. Moreover, we provide results for O and CO co-adsorption on the clean and Pd doped Ag(1 1 1) surfaces, indicating that Pd can act as an electronic promoter for the CO oxidation reaction.     

DFT calculations of adenine adsorption on coin metal (1 1 0) surfaces

Density functional theory is used to analyze in detail the adsorption of the adenine molecule on the (1 1 0) surfaces of Cu, Ag, and Au. While the adsorption configurations are similar in all three cases – the molecule bonds via two nitrogen atoms to the substrate – the details like charge transfer or local strain a rather different. The molecule–substrate interaction in case of Cu is stronger than for the more noble metals Ag and Au. Longe-range dispersion forces stabilize the adsorption configuration in dependence on the specific adsorption geometry. In case of Ag and Au, relativistic effects are found to be important.     

Systematic studies on surface modifications by ARUPS on Shockley-type surface states

The quasi two-dimensional surface state on noble metal (1 1 1)-surfaces can be used as a sensitive probe for different surface modifications, adsorption processes, and interactions between adsorbate and substrate. Already one monolayer of physisorbed Xe on Au(1 1 1) is responsible for a characteristic shift of the Shockley state towards the Fermi level and the surface state experiences an increase in spin-orbit splitting of up to 35%. In contrast to the physisorption process of rare gases, a sub-monolayer coverage of an alkali metal, e.g., Na on Au(1 1 1), has the opposite effect on the Shockley state, i.e. an increase in binding energy, until it reaches the bottom of the L-gap and vanishes into the bulk states. Additionally, we studied the intermetallic system Ag/Au(1 1 1) which differs substantially from the other systems because of the similarity in the electronic structure between substrate and overlayer.     

Electrical conductance at initial stage in epitaxial growth of Pb, Ag, Au and In on modified Si(1 1 1) surface

The electronic properties of thin metallic films of Pb, Ag, Au and In atoms deposited at 105 K on well defined metallic surface, i.e. Si(1 1 1)-(6 × 6)Au surface with 10 ML of annealed Pb, were investigated using four-point probe method in UHV condition. The structure of the substrate and deposited metals were monitored by the RHEED system. The electrical conductance, measured during the deposition of In and Pb atoms, shows the local minimum for the coverage equals about 0.3 ML whereas for Au and Ag atoms the conductance decreases during the first monolayer growth. For Au atoms the local maximum in the conductance was observed for the coverage about 0.55 ML, which can be connected with localized states. To describe theoretically the conductance behavior the tight-binding Hamiltonian and equation of motion for the Green’s function were used and good qualitative agreement was obtained.     

The chemical potential in surface segregation calculations: AgPd alloys

We put forward a technique for calculating the surface segregation profile in substitutional disordered alloys. The surface internal energy and the effective bulk and surface chemical potentials are calculated using the full charge density exact muffin-tin orbitals method, combined with the coherent potential approximation. The application of our approach is demonstrated to the close-packed surface of Ag_cPd_1−c random alloys with 0 < c < 1. The surface concentration profile, surface energy and segregation energy are investigated as functions of bulk composition. The present results are compared with former theoretical and experimental data. It is found that at low temperature, Ag segregates to the surface layer for the entire bulk composition range. At 0 K, the subsurface layer contains 100% Pd for c ? 0.4, and somewhat more than (2c − 1) Ag in alloys with c > 0.5. The temperature dependence of the segregation profile is significant for Pd rich alloys and for alloys with intermediate concentrations. At temperatures ?600 K, the subsurface layer is obtained to be almost bulk like.     

Atomistic simulation of point defects at low-index surfaces of noble metals

The formation energies and the migration energies of an isolated vacancy and adatom formed on low-index surfaces are calculated with MAEAM for three noble metals Cu, Ag and Au. The results indicate that the formation energies of an isolated vacancy or adatom increase with increasing atom density in the sequence (1 1 0) → (1 0 0) → (1 1 1), and it is more difficult to form an adatom than to form a vacancy at the same surface. For the mobility of an isolated vacancy, the migration energy grows in the sequence (1 0 0) → (1 1 0) → (1 1 1) for each noble metal. However, a much less migration energy is obtained for the migration of an adatom on (1 1 1) surface.     

Array of double Au-Ag chains on the Si(5 5 7) surface

Using scanning tunneling microscopy we study the topographic properties of Ag structure on the Au induced, highly ordered Si(5 5 7) surface. Topography measurements show that a small amount of Ag (0.25 ML) deposited on that surface leads to considerable modifications of the one-dimensional structure induced by Au atoms. In particular, we observe two different chains on each terrace, which are identified as Si adatoms and Ag chain structures. The STM topography of those chains strongly depends on the bias voltage, indicating an important role of electronic effects in this system.     

Photoemission study of glycine adsorption on Cu/Au(1 1 1) interfaces

The adsorption of glycine on Au(1 1 1) pre-deposited with different amounts of Cu was investigated with both conventional X-ray photoelectron spectroscopy (XPS) and synchrotron-based photoemission. In the Cu submonolayer range, glycine physically adsorbs on the Cu/Au(1 1 1) surfaces in its zwitterionic form and completely desorbs at 350 K. The C 1s, O 1s and N 1s core level binding energies monotonically increase with Cu coverage. This indicates that, in the Cu submonolayer range, the admetal is alloyed with Au rather than forming overlayers on the Au(1 1 1) substrate, consistent with our recent experimental and theoretical results [X. Zhao, P. Liu, J. Hrbek, J.A. Rodriguez, M. Pérez, Surf. Sci. 592 (2005) 25]. Upon increasing the amount of deposited Cu over 1 ML, part of the glycine overlayer transforms from the zwitterionic form to the anionic form (NH₂CH₂COO⁻) and adsorbs chemically on the Cu/Au(1 1 1) surface with the N 1s binding energy shifted by −2.3 eV. When the amount of deposited Cu is at 3.0 or 6.0 ML, the intensity of the N 1s chemisorption peak increases with aging time at 300 K. It indicates that glycine adsorption induces Cu segregation from the subsurface region onto the top layer of the substrate. Judging from the initial N 1s peak intensities, it is concluded that 64% and 36% of the top layer are still occupied by Au atoms before glycine adsorption even when the amounts of deposited Cu are 3.0 and 6.0 ML, respectively. On the Au(1 1 1) surface pre-dosed with 6.0 ML of Cu, part of the chemisorbed glycine will desorb and part will decompose upon heating to 450-500 K. In addition, about 20% of the glycine exists in the neutral form when the glycine overlayer was dosed on Cu/Au(1 1 1) held at 100 K.     

Growth and thermal stability of ultra-thin Ag and Au layers on Mo(1 1 1) surface

The influence of temperature on the growth process of ultra-thin Ag and Au layers on the Mo(1 1 1) surface was investigated. At 300 K growth of the Stranski-Krastanov type was found for Ag; for Au growth of the monolayer plus simultaneous multilayers type was found, where a base layer is one physical layer. The first three geometrical adsorbed layers for Ag are thermally stable. For annealed Au layers triangle features with base side length from 15 to 35 Å were formed for θ < 6 monolayer (ML), and for θ > 6 ML part of the Au formed a flat adlayer with Au atoms grouped in equilateral triangles with side length 7 Å. The presence of Au layers does not cause faceting, layers are not smooth which could be caused by the fact that Au does not wets the substrate. For Ag thick layers reversible wetting/non-wetting transition was observed at 600 K. Ag layers on Mo(1 1 1) surface did not lead to faceting.     

Surface structures formed by individual adsorption and coadsorption of Mn and Bi on Cu(0 0 1), studied by LEED

We have studied the individual adsorption of Mn and Bi, and their coadsorption on Cu(0 0 1) by low-energy electron diffraction (LEED). For Mn, we have determined the c(2 × 2) structure formed at 300 K, whose structure had been determined by several methods. We reconfirmed by a tensor LEED analysis that it is a substitutional structure and that a previously reported large corrugation (0.30 Å) between substitutional Mn and remaining surface Cu atoms coincides perfectly with the present value. In the individual adsorption of Bi, we have found a c(4 × 2) structure, which is formed by cooling below ∼250 K a surface prepared by Bi deposition of ∼0.25 ML coverage at 300 K where streaky half-order LEED spots appear. The c(4 × 2) structure has been determined by the tensor LEED analysis at 130 K and it is a substitutional structure. In the coadsorption, we found a c(6 × 4) structure, which has been determined by the tensor LEED analysis. It is very similar to the previously determined structure of the c(6 × 4) formed by coadsorption of Mg and Bi, and embedded MnBi₄ clusters are arranged in the top Cu layer instead of MgBi₄. Large lateral displacements of Bi atoms in the c(6 × 4)-(Mn + Bi) suggest that the Mn atoms undergo the size-enhancement caused by their large magnetic moment.     

Structural properties and diffusion processes of the Cu3Au (0 0 1) surface

The surface relaxation and surface energy of both the mixed AuCu and pure Cu terminated Cu₃Au (0 0 1) surfaces are simulated and calculated by using the modified analytical embedded-atom method. We find that the mixed AuCu termination is energetically preferred over the pure Cu termination thereby the mono-vacancy diffusion is also investigated in the topmost few layers of the mixed AuCu terminated Cu₃Au (0 0 1) surface. In the mixed AuCu terminated surface the relaxed Au atoms are raised above Cu atoms for 0.13 Å in the topmost layer. All the surface atoms displace outwards, this effect occurs in the first three layers and changes the first two inter-layer spacing. For mono-vacancy migration in the first layer, the migration energies of Au and Cu mono-vacancy via two-type in-plane displace: the nearest neighbor jump (NNJ) and the second nearest neighbor jump (2NNJ), are calculated and the results show that the NNJ requires a much lower energy than 2NNJ. For the evolution of the energy requirements for successive nearest neighbor jumps (SNNJ) along three different paths: circularity, zigzag and beeline, we find that the circularity path is preferred over the other two paths due to its minimum energy barriers and final energies. In the second layer, the NN jumps in intra- and inter-layer of the Cu mono-vacancy are investigated. The calculated energy barriers and final energies show that the vacancy prefer jump up to a proximate Cu site. This replacement between the Cu vacancy in the second layer and Cu atom in the first layer is remunerative for the Au atoms enrichment in the topmost layer.     

Visible photocurrent response of TiO2 anode

The photoelectrochemical response to the electromagnetic radiation over the visible range is particularly sought for from the point of view of the efficiency of hydrogen generation by water photolysis in a photoelectrochemical solar cell, PEC. The PEC used in this work comprises thin film TiO₂ - based photoanode, Pt foil covered with Pt black as a cathode and SCE as a reference electrode, immersed in an electrolyte solution. Titanium dioxide thin films are deposited by means of rf reactive sputtering and modified, when necessary, by Au or Ag ultra-thin overcoatings. Here we show that even unmodified TiO₂ photoanode, shows a photocurrent peak over the visible range of the light spectrum (λ = 500-650 nm). The effect of the surface modification by noble metals and properties of the aqueous electrolyte on the visible photocurrent are studied. The optical spectra indicate an increased absorption due to noble metal deposits at 410 nm for Ag and at 600 nm for Au. In contrast, the photocurrent peak over the visible range (500 nm < λ < 650 nm) changes its symmetry and decreases in intensity with the increasing thickness of noble metals layers. The visible photoresponse is explained in terms of OH formation at the interface between TiO₂ electrode and aqueous electrolyte.     

Formation of linear structures of Sr and Gd films on the Mo(1 1 2) and W(1 1 2) surfaces

At low coverages, alkaline earth and rare earth layers adsorbed on furrowed transition metal surfaces--such as W(1 1 2) and Mo(1 1 2)--tend to form commensurate linear structures built of monoatomic chains directed across the furrows. Presented Monte Carlo simulations provide insight into parameters of the long-range indirect interaction that, in competition with a dipole-dipole interaction, leads to formation of the linear structures. The most impressive result of the simulations is the revealed repulsive effective interaction between adjacent atoms in linear Sr chains on W(1 1 2) surface. In this case, formation of the linear chains is accomplished due to pronounced minima in the potential of indirect interaction along the surface furrows. This result predicts that a single Sr chain cannot exist on the W(1 1 2) surface.     

Ag nanostructures on Au(7 8 8): A self-assembled superlattice of metallic quantum resonators

We have studied by scanning tunneling microscopy (STM) the effect of the reconstruction of a stepped Au(1 1 1) surface on the growth of silver sub-monolayer deposition. For narrow terraces, the reconstruction is disturbed and its pattern changes, Ag growth is therefore influenced. Thus growth of Ag on Au(7 8 8) vicinal surface can be controlled and leads to the formation of a highly ordered superlattice of nanostructures. Moreover, we show by tunneling conductance images that Ag islands exhibit electronic confinement effects of the Shockley surface state. Due to the homogeneity of their shapes and sizes, all the nanostructures of the self-assembled superlattice should exhibit similar electronic properties.     

STS investigations of temperature dependence of Au(1 1 1) surface state energy position

High temperature scanning tunneling spectroscopy (HT-STS) was used to investigate the electronic structure of Au(1 1 1) at different temperatures in the energy range 0-1 eV below the Fermi level. We concentrated on the influence of temperature on the Shockley surface state (SS) appearing on noble metals surface due to a surface projected bulk bang gap in [1 1 1] direction. The influence of temperature on the projected band gap edge (BE) was also investigated. The experiment was carried out in the temperature range 294-580 K. As the result of the experiment a delicate shift of the SS and the BE in direction of the Fermi level was reported.     

Quantitative analysis of the surface reconstruction induced band-gap in the Shockley state on monolayer systems on noble metals

One monolayer of Ag deposited on Cu(1 1 1) shows two kinds of characteristic reconstruction, depending on the conditions of the preparation: the incommensurate moiré structure appears for one monolayer prepared at 200 K whereas a monolayer deposited at room temperature (or higher) exhibits a quasi-commensurate triangular structure. By high-resolution ARUPS measurements on the triangular structure we find an opening of a gap in the Shockley state band, which is a signature of the super-lattice. On the other hand, no gap opening is observed on the moiré structure. In addition, we show that the Shockley state plays an important role in the adsorption process of rare gas atoms on these surfaces. ARUPS experiments on adsorbed Xe on 0.6 ML Ag/Cu(1 1 1) show clearly that the Xe atoms favor the adsorption on the Ag islands, before the Cu terraces will be covered at higher Xe exposure.     

The energy and structure of (0 0 1) twist grain boundary in noble metals

The relaxed energy and structure of (0 0 1) twist grain boundary (GB) in noble metals Au, Ag and Cu are simulated by the MAEAM. In-boundary translation between two adjacent grains results in a periodic energy variation and the period is a square with the side length L_Σ/Σ. The lowest energy appears when the two grains are translated relatively to either corner or center of the periodic square. The relaxed GB energy increases smoothly for low-angle boundaries and levels off for larger-angle boundaries except a cusp appeared at θ = 36.87° (Σ = 5). After relaxation, the symmetry of the GB structure is not changed but the displacement of the atoms parallel to the GB plane decreases with increasing the distance of the atoms from the GB plane.