Formamide reactions on rutile TiO2(0 1 1) surface

The reaction of formamide over the (0 1 1) faceted TiO₂(0 0 1) surface has been studied by Temperature Programmed Desorption (TPD) and X-ray Photoelectron Spectroscopy (XPS). Two main reactions were observed: dehydration to HCN and H₂O and decomposition to NH₃ and CO. The dehydration reaction was found to be three to four times larger than the decomposition at all coverages. Each of these reactions is found to occur in two temperature domains which are dependent upon surface coverage. The low temperature pathway (at about 400 K) is largely insensitive to surface coverage while the high temperature pathway (at about 500 K) shifts to lower temperatures with increasing surface coverage. These two temperature pathways may indicate two adsorption modes of formamide: molecular (via an η¹(O) mode of adsorption) and dissociative (via an η²(O,N) mode of adsorption). C1s and N1s XPS scans indicated the presence of multiple species after formamide absorption at 300 K. These occurred at ca. 288.5 eV (-CONH-) and 285 eV (sp³/sp² C) for the C1s and 400 eV-(NH₂), 398 eV (-NH) and 396 eV (N) for the N1s and result from further reaction of formamide with the surface.     

In situ XPS study of Pd(1 1 1) oxidation. Part 1: 2D oxide formation in 10 mbar O2

The oxidation of the Pd(1 1 1) surface was studied by in situ XPS during heating and cooling in 3 × 10⁻³ mbar O₂. A number of adsorbed/dissolved oxygen species were identified by in situ XPS, such as the two dimensional surface oxide (Pd₅O₄), the supersaturated O_ads layer, dissolved oxygen and the R 12.2° surface structure.Exposure of the Pd(1 1 1) single crystal to 3 × 10⁻³ mbar O₂ at 425 K led to formation of the 2D oxide phase, which was in equilibrium with a supersaturated O_ads layer. The supersaturated O_ads layer was characterized by the O 1s core level peak at 530.37 eV. The 2D oxide, Pd₅O₄, was characterized by two O 1s components at 528.92 eV and 529.52 eV and by two oxygen-induced Pd 3d_5/2 components at 335.5 eV and 336.24 eV. During heating in 3 × 10⁻³ mbar O₂ the supersaturated O_ads layer disappeared whereas the fraction of the surface covered with the 2D oxide grew. The surface was completely covered with the 2D oxide between 600 K and 655 K. Depth profiling by photon energy variation confirmed the surface nature of the 2D oxide. The 2D oxide decomposed completely above 717 K. Diffusion of oxygen in the palladium bulk occurred at these temperatures. A substantial oxygen signal assigned to the dissolved species was detected even at 923 K. The dissolved oxygen was characterised by the O 1s core level peak at 528.98 eV. The “bulk” nature of the dissolved oxygen species was verified by depth profiling.During cooling in 3 × 10⁻³ mbar O₂, the oxidised Pd²⁺ species appeared at 788 K whereas the 2D oxide decomposed at 717 K during heating. The surface oxidised states exhibited an inverse hysteresis. The oxidised palladium state observed during cooling was assigned to a new oxide phase, probably the R 12.2° structure.     

An XPS study on the surface reduction of V2O5(0 0 1) induced by Ar ion bombardment

The effect of the irradiation with Al Kα X-rays during an XPS measurement upon the surface vanadium oxidation state of a fresh in vacuum cleaved V₂O₅(0 0 1) crystal was examined. Afterwards, the surface reduction of the V₂O₅(0 0 1) surface under Ar⁺ bombardment was studied. The degree of reduction of the vanadium oxide was determined by means of a combined analysis of the O1s and V2p photoelectron lines. Asymmetric line shapes were needed to fit the V³⁺2p photolines, due to the metallic character of V₂O₃ at ambient temperature. Under Ar⁺ bombardment, the V₂O₅(0 0 1) crystal surface reduces rather fast towards the V₂O₃ stoichiometry, after which a much slower reduction of the vanadium oxide occurs.     

Hydroxylated α-Al2O3 (0 0 0 1) surfaces and metal/α-Al2O3 (0 0 0 1) interfaces

X-ray photoelectron spectroscopy was applied to study the hydroxylation of α-Al₂O₃ (0 0 0 1) surfaces and the stability of surface OH groups. The evolution of interfacial chemistry of the α-Al₂O₃ (0 0 0 1) surfaces and metal/α-Al₂O₃ (0 0 0 1) interfaces are well illustrated via modifications of the surface O1s spectra. Clean hydroxylated surfaces are obtained through water- and oxygen plasma treatment at room temperature. The surface OH groups of the hydroxylated surface are very sensitive to electron beam illumination, Ar⁺ sputtering, UHV heating, and adsorption of reactive metals. The transformation of a hydroxylated surface to an Al-terminated surface occurs by high temperature annealing or Al deposition.     

CO2 adsorption on Cr(1 1 0) and Cr2O3(0 0 0 1)/Cr(1 1 0)

We attempt to correlate qualitatively the surface structure with the chemical activity for a metal surface, Cr(1 1 0), and one of its surface oxides, Cr₂O₃(0 0 0 1)/Cr(1 1 0). The kinetics and dynamics of CO₂ adsorption have been studied by low energy electron diffraction (LEED), Aug er electron spectroscopy (AES), and thermal desorption spectroscopy (TDS), as well as adsorption probability measurements conducted for impact energies of E_i = 0.1-1.1 eV and adsorption temperatures of T_s = 92-135 K. The Cr(1 1 0) surface is characterized by a square shaped LEED pattern, contamination free Cr AES, and a single dominant TDS peak (binding energy E_d = 33.3 kJ/mol, first order pre-exponential 1 × 10¹³ s⁻¹). The oxide exhibits a hexagonal shaped LEED pattern, Cr AES with an additional O-line, and two TDS peaks (E_d = 39.5 and 30.5 kJ/mol). The initial adsorption probability, S₀, is independent of T_s for both systems and decreases exponentially from 0.69 to 0.22 for Cr(1 1 0) with increasing E_i, with S₀ smaller by ∼0.15 for the surface oxide. The coverage dependence of the adsorption probability, S(Θ), at low E_i is approx. independent of coverage (Kisliuk-shape) and increases initially at large E_i with coverage (adsorbate-assisted adsorption). CO₂ physisorbs on both systems and the adsorption is non-activated and precursor mediated. Monte Carlo simulations (MCS) have been used to parameterize the beam scattering data. The coverage dependence of E_d has been obtained by means of a Redhead analysis of the TDS curves.     

Driving force for the WO3(0 0 1) surface relaxation

The optimized structure of the WO₃(0 0 1) surface with various types of termination ((1 × 1)O, (1 × 1)WO₂, and c(2 × 2)O) has been simulated using density functional theory with the Perdew-Wang 91 gradient corrected exchange-correlation functional. While the energy of bulk WO₃ depends weakly on the distortions and tilting of the WO₆ octahedra, relaxation of the (0 0 1) surface results in a significant decrease of surface energy (from 10.2 × 10⁻² eV/Ų for the cubic ReO₃-like, c(2 × 2)O-terminated surface to 2.2 × 10⁻² eV/Ų for the relaxed surface). This feature illustrates a potential role of surface relaxation in formation of crystalline nano-size clusters of WO₃. The surface relaxation is accompanied by a dramatic redistribution of the density of states near the Fermi level, in particular a transformation of surface electronic states. This redistribution is responsible for the decrease of electronic energy and therefore is suggested to be the driving force for surface relaxation of the WO₃(0 0 1) surface and, presumably, similar surfaces of other transition metal oxides.     

First-principles study on the catalytic role of Ag in the oxygen adsorption of LaMnO3(0 0 1) surface

In the present paper, the catalytic role of Ag in the oxygen adsorption of LaMnO₃(0 0 1) surface has been theoretically investigated using first-principles calculations based on the density functional theory (DFT) and pseudopotential method. The O₂ adsorption energy is larger for the vertical adsorption and the covalent bond was formed between O₂ molecule and surface Mn. The calculation of electronic properties of interaction between Ag atom and LaMnO₃(0 0 1) surface demonstrates that the most stable position for Ag adsorption is hollow site. The O₂ adsorption energy dramatically increased from 0.298 eV to 1.108 eV due to Ag pre-adsorbed. It is Ag pre-adsorbed that facilitates O₂ adsorption on surface. The bond length and bond population of O₂ molecule indicate that Ag atom facilitates O₂ molecule dissociative adsorption. The Ag atom strengthens LaMnO₃(0 0 1) substrate activity and activity center was formed on surface, which enhances the electrocatalytic activity of LaMnO₃ as solid oxide fuel cells cathode material at low temperature.     

Low temperature adsorption of oxygen on reduced V2O3(0 0 0 1) surfaces

Well ordered V₂O₃(0 0 0 1) films were prepared on Au(1 1 1) and W(1 1 0) substrates. These films are terminated by a layer of vanadyl groups under typical UHV conditions. Reduction by electron bombardment may remove the oxygen atoms of the vanadyl layer, leading to a surface terminated by vanadium atoms. The interaction of oxygen with the reduced V₂O₃(0 0 0 1) surface has been studied in the temperature range from 80 to 610 K. Thermal desorption spectroscopy (TDS), infrared reflection absorption spectroscopy (IRAS), high resolution electron energy loss spectroscopy (HREELS), X-ray photoelectron spectroscopy (XPS), and density functional theory (DFT) were used to study the adsorbed oxygen species. Low temperature adsorption of oxygen on reduced V₂O₃(0 0 0 1) occurs both dissociatively and molecularly. At 90 K a negatively charged molecular oxygen species is observed. Upon annealing the adsorbed oxygen species dissociates, re-oxidizing the reduced surface by the formation of vanadyl species. Density functional theory was employed to calculate the structure and the vibrational frequencies of the O₂ species on the surface. Using both cluster and periodic models, the surface species could be identified as η²-peroxo () lying flat on surface, bonded to the surface vanadium atoms. Although the O-O vibrational normal mode involves motions almost parallel to the surface, it can be detected by infrared spectroscopy because it is connected with a change of the dipole moment perpendicular to the surface.     

Formation of oxygen vacancies on the TiO2(1 1 0) surfaces

Density functional theory was employed to investigate the formation and properties of the oxygen vacancies on the rutile TiO₂(1 1 0) surface. It is found that the formation of the positively charged bridging-oxygen vacancy (BOV⁺, 4.2 eV) is the most favored one, followed by the positively charged in-plane-oxygen vacancy (POV⁺, 4.5 eV). In contrast, the formation of the neutral bridging-oxygen and in-plane-oxygen vacancies (BOV and POV), and their dication oxygen vacancies (BOV²⁺ and POV²⁺) needs much higher energies (7.9 and 8.3 vs. 8.1 and 8.6 eV), respectively.     

The structure of the V2O3(0 0 0 1) surface: A scanned-energy mode photoelectron diffraction study

Scanned-energy mode photoelectron diffraction (PhD), using the O 1s and V 2p photoemission signals, together with multiple-scattering simulations, have been used to investigate the structure of the V₂O₃(0 0 0 1) surface. The results support a strongly-relaxed half-metal termination of the bulk, similar to that found in earlier studies of Al₂O₃(0 0 0 1) and Cr₂O₃(0 0 0 1) surfaces based on low energy electron and surface X-ray diffraction methods. However, the PhD investigation fails to provide definitive evidence for the presence or absence of surface vanadyl (VO) species associated with atop O atoms on the surface layer of V atoms. Specifically, the best-fit structure does not include these vanadyl species, although an alternative model with similar relaxations but including vanadyl O atoms yields a reliability-factor within the variance of that of the best-fit structure.     

Adsorption of water on thin V2O3(0 0 0 1) films

V₂O₃(0 0 0 1) films have been grown epitaxially on Au(1 1 1) and W(1 1 0). Under typical UHV conditions these films are terminated by a layer of vanadyl groups as has been shown previously [A.-C. Dupuis, M. Abu Haija, B. Richter, H. Kuhlenbeck, H.-J. Freund, V₂O₃(0 0 0 1) on Au(1 1 1) and W(1 1 0): growth, termination and electronic structure, Surf. Sci. 539 (2003) 99]. Electron irradiation may remove the oxygen atoms of this layer. H₂O adsorption on the vanadyl terminated surface and on the reduced surface has been studied with thermal desorption spectroscopy (TDS), vibrational spectroscopy (IRAS) and electron spectroscopy (XPS) using light from the BESSY II electron storage ring in Berlin. It is shown that water molecules interact only weakly with the vanadyl terminated surface: water is adsorbed molecularly and desorbs below room temperature. On the reduced surface water partially dissociates and forms a layer of hydroxyl groups which may be detected on the surface up to T ∼ 600 K. Below ∼330 K also co-adsorbed molecular water is detected. The water dissociation products desorb as molecular water which means that they recombine before desorption. No sign of surface re-oxidation could be detected after desorption, indicating that the dissociation products desorb completely.     

Characterizations of n-type ferromagnetic GaMnN thin film grown on GaN/Al2O3 (0 0 0 1) by metal-organic chemical vapor deposition

A high-quality ferromagnetic GaMnN (Mn=2.8 at%) film was deposited onto a GaN buffer/Al₂O₃(0 0 0 1) at 885 °C using the metal-organic chemical vapor deposition (MOCVD) process. The GaMnN film shows a highly c-axis-oriented hexagonal wurtzite structure, implying that Mn doping into GaN does not influence the crystallinity of the film. No Mn-related secondary phases were found in the GaMnN film by means of a high-flux X-ray diffraction analysis. The composition profiles of Ga, Mn, and N maintain nearly constant levels in depth profiles of the GaMnN film. The binding energy peak of the Mn 2p_3/2 orbital was observed at 642.3 eV corresponding to the Mn (III) oxidation state of MnN. The presence of metallic Mn clusters (binding energy: 640.9 eV) in the GaMnN film was excluded. A broad yellow emission around 2.2 eV as well as a relatively weak near-band-edge emission at 3.39 eV was observed in a Mn-doped GaN film, while the undoped GaN film only shows a near-band-edge emission at 3.37 eV. The Mn-doped GaN film showed n-type semiconducting characteristics; the electron carrier concentration was 1.2×10²¹/cm³ and the resistivity was 3.9×10⁻³ Ω cm. Ferromagnetic hysteresis loops were observed at 300 K with a magnetic field parallel and perpendicular to the ab plane. The zero-field-cooled and field-cooled curves at temperatures ranging from 10 to 350 K strongly indicate that the GaMnN film is ferromagnetic at least up to 350 K. A coercive field of 250 Oe and effective magnetic moment of 0.0003 μ_B/Mn were obtained. The n-type semiconducting behavior plays a role in inducing ferromagnetism in the GaMnN film, and the observed ferromagnetism is appropriately explained by a double exchange mechanism.     

Surface electronic structure of α-Mo2C(0 0 0 1)

The electronic structure of α-Mo₂C(0 0 0 1) has been investigated by angle-resolved photoemission spectroscopy utilizing synchrotron radiation. A sharp peak is observed at 3.3 eV in normal-emission spectra. Since the peak shows no dispersion as a function of photon energy and is sensitively attenuated by oxygen adsorption, the initial state of the peak is attributed to a surface state. Resonant photoemission study shows that the state includes substantial contribution of 4d orbitals of the Mo atoms in the second layer. The emissions with constant kinetic energies of 22 and 31 eV above the Fermi level (E_F) are found in normal-emission spectra, and these emissions are interpreted as originating from the Mo N₁N₂₃V and N₂₃VV Auger transitions, respectively.     

Theoretical studies on the adsorption and decomposition of H2O on Pd(1 1 1) surface

To provide information about the chemistry of water on Pd surfaces, we performed density functional slab model studies on water adsorption and decomposition at Pd(1 1 1) surface. We located transition states of a series of elementary steps and calculated activation energies and rate constants with and without quantum tunneling effect included. Water was found to weakly bind to the Pd surface. Co-adsorbed species OH and O that are derivable from H₂O stabilize the adsorbed water molecules via formation of hydrogen bonds. On the clean surface, the favorable sites are top and bridge for H₂O and OH, respectively. Calculated kinetic parameters indicate that dehydrogenation of water is unlikely on the clean regular Pd(1 1 1) surface. The barrier for the hydrogen abstraction of H₂O at the OH covered surface is approximately 0.2-0.3 eV higher than the value at the clean surface. Similar trend is computed for the hydroxyl group dissociation at H₂O or O covered surfaces. In contrast, the O-H bond breaking of water on oxygen covered Pd surfaces, H₂O_ad + O_ad → 2OH_ad, is predicted to be likely with a barrier of ∼0.3 eV. The reverse reaction, 2OH_ad → H₂O_ad + O_ad, is also found to be very feasible with a barrier of ∼0.1 eV. These results show that on oxygen-covered surfaces production of hydroxyl species is highly likely, supporting previous experimental findings.     

Chloromethane surface chemistry on Fe3O4(1 1 1)-(2 × 2): A thermal desorption spectrometry comparison of CCl4, CBr2Cl2, and CH2Cl2

The surface chemistry of CBr₂Cl₂ on the Fe₃O₄(1 1 1)-(2 × 2) selvedge of single-crystal α-Fe₂O₃(0 0 0 1) has been investigated using temperature programmed reaction and desorption (TPR/D) measurements. The spectra obtained in this case show that strong chemisorption occurs and that a series of adsorbed halogenated reaction products are present. By comparison, studies of the adsorbed phase of CH₂Cl₂ show that only physisorption occurs. The TPR/D spectra of CBr₂Cl₂ show that dissociative formation of CCl₂ followed by its reaction with lattice oxygen is central to the monolayer reaction chemistry in this chloromethane. The branching ratios of the various desorbed products are compared with those obtained from CCl₄ adsorbed on the same (2 × 2) surface.     

The effect of preadsorbed K on the size distribution of Au nanoparticles on TiO2(1 1 0) surface

The effect of K on the morphology of Au nanoparticles deposited on TiO₂(1 1 0) surface is investigated by STM-STS and AES methods. For comparison, the enhanced concentration of oxygen defect sites generated by Ar⁺ bombardment was also studied. It was found that both the K additive and the oxygen defect sites induce a pronounced decrease in the average size of the Au nanoparticles evolved at 320 K. On the clean TiO₂(1 1 0) the average size of Au particles is 4.3 nm at approximately monolayer coverage of gold, while in the presence of K or oxygen vacancies this value decreased to 2.5 nm. In spite of the reduced average diameter detected at room temperature, the mean size of the Au nanoparticles increased significantly from 2.5 nm up to 7 nm on the effect of annealing at 500-700 K for K precoverages of 0.3-1 ML. For the clean and the Ar⁺ pretreated TiO₂(1 1 0) surfaces the mean size of the Au particles changed only slightly on the effect of the same thermal treatments.     

Hydroxylation-induced modifications of the Al2O3/NiAl(0 0 1) surface at low water vapour pressure

STM, STS, LEED and XPS data for crystalline θ-Al₂O₃ and non-crystalline Al₂O₃ ultra-thin films grown on NiAl(0 0 1) at 1025 K and exposed to water vapour at low pressure (1 × 10⁻⁷-1 × 10⁻⁵ mbar) and room temperature are reported. Water dissociation is observed at low pressure. This reactivity is assigned to the presence of a high density of coordinatively unsaturated cationic sites at the surface of the oxide film. The hydroxyl/hydroxide groups cannot be directly identify by their XPS binding energy, which is interpreted as resulting from the high BE positions of the oxide anions (O_1s signal at 532.5-532.8 eV). However the XPS intensities give evidence of an uptake of oxygen accompanied by an increase of the surface coverage by Al³⁺ cations, and a decrease of the concentration in metallic Al at the alloy interface. A value of ∼2 for the oxygen to aluminium ions surface concentration ratio indicates the formation of an oxy-hydroxide (AlO_xOH_y with x + y ∼ 2) hydroxylation product. STM and LEED show the amorphisation and roughening of the oxide film. At P(H₂O) = 1 × 10⁻⁷ mbar, only the surface of the oxide film is modified, with formation of nodules of ∼2 nm lateral size covering homogeneously the surface. STS shows that essentially the valence band is modified with an increase of the density of states at the band edge. With increasing pressure, hydroxylation is amplified, leading to an increased coverage of the alloy by oxy-hydroxide products and to the formation of larger nodules (∼7 nm) of amorphous oxy-hydroxide. Roughening and loss of the nanostructure indicate a propagation of the reaction that modifies the bulk structure of the oxide film. Amorphisation can be reverted to crystallization by annealing under UHV at 1025 K when the surface of the oxide film has been modified, but not when the bulk structure has been modified.     

Scanning tunnelling microscopy and spectroscopy of the reduced TiO2(1 0 0) surface

Scanning tunnelling microscopy and current imaging tunnelling spectroscopy were used to study the topographic and electronic structure of a reduced TiO₂(1 0 0) surface. The STM results showed that the TiO₂(1 0 0) surface is capable to form (1 × 7) reconstruction which can transform to (1 × 3) reconstruction due to reoxidation of the surface. The CITS results showed that the (1 × 7) reconstruction is much more metallic in compared to the (1 × 3) reconstruction showing pronounced surface states at energy 1.3 eV and 0.8 eV below the Fermi level and at energy 1.0-1.2 eV above the Fermi level.     

Characterization of single-crystalline In2O3 films deposited on Y-stabilized ZrO2 (1 0 0) substrates by MOCVD

Epitaxial In₂O₃ films have been deposited on Y-stabilized ZrO₂ (YSZ) (1 0 0) substrates by metalorganic chemical vapor deposition (MOCVD). The films were deposited at different substrate temperatures (450-750 °C). The film deposited at 650 °C has the best crystalline quality, and observation of the interface area shows a clear cube-on-cube epitaxial relationship of In₂O₃(1 0 0)||YSZ(1 0 0) with In₂O₃[0 0 1]||YSZ[0 0 1]. The Hall mobility of the single-crystalline In₂O₃ film deposited at 650 °C is as high as 66.5 cm² V⁻¹ s⁻¹ with carrier concentration of 1.5 × 10¹⁹ cm⁻³ and resistivity of 6.3 × 10⁻³ Ω cm. The absolute average transmittance of the obtained films in the visible range exceeds 95%.     

Impact of O2 exposure on surface crystallinity of clean and Ba terminated Ge(1 0 0) surfaces

In analogy with the case of Sr on Si [Y. Liang, S. Gan, M. Engelhard, Appl. Phys. Lett. 79 (2001) 3591], we studied surface crystallinity and oxidation behaviour of clean and Ba terminated Ge(1 0 0) surfaces as a function of oxygen pressure and temperature. The structural and chemical changes in the Ge surface layer were monitored by LEED, XPS and real-time RHEED. In contrast to the oxidation retarding effect, observed for 1/2 monolayer of Sr on Si, the presence of a Ba termination layer leads to a pronounced increase in Ge oxidation rate with respect to clean Ge. In fact, while the Ge(1 0 0) surface terminated with 1/2 ML Ba amorphizes for a pO₂ of 10⁻² Torr, LEED indicates that clean Ge forms a thin (4.5 Å), 1 × 1 ordered oxide upon aggressive O₂ exposure (150 Torr, 200 °C, 30 min). We briefly discuss the origins for the difference in behaviour between Ba on Ge and Sr on Si.