助剂Fe和反应修饰剂修饰的Ru催化剂上苯选择加氢制环己烯

共沉淀法制备了Ru-Fe(x)催化剂,并利用X射线衍射(XRD)、X射线荧光光谱(XRF)、N2物理吸附和透射电镜等手段对催化剂进行了表征.结果表明,Ru-Fe(x)催化剂中助剂Fe以Fe3O4形式存在.单独Fe3O4并不能提高Ru催化剂的环己烯选择性.但在加氢过程中Fe3O4可与反应修饰剂ZnSO4反应生成(Zn(OH)2)3(ZnSO4)(H2O)x(x=1 or 3).化学吸附的(Zn(OH)2)3(ZnSO4)(H2O)x(x=1 or 3)在提高Ru催化剂环己烯选择性中起着关键作用.此外,Ru-Fe(x)催化剂的性能还与浆液中的Zn2+浓度和pH值有关.在0.61 mol/L ZnSO4溶液中Ru-Fe(0.47)催化剂不但给出了56.7%的环己烯收率,而且具有良好的稳定性和重复使用性能.化学吸附在Ru表面的Fe2+同样能提高Ru催化剂的环己烯选择性.在0.29 mol/L和0.61 mol/L FeSO4溶液中Ru-Fe(0.47)催化剂上化学吸附Fe2+量近似,性能近似.因为Fe2+和Zn2+性质的差异,在0.29 mol/L和0.61 mol/L FeSO4溶液中Ru-Fe(0.47)催化剂的环己烯选择性分别低于在同浓度的ZnSO4溶液中的.     

改性铝土矿载体负载Ru催化剂上的水煤气变换制氢

采用水热法对天然铝土矿进行改性,获得高比表面积的铝土矿(bauxite)载体.用等体积浸渍法制备了Ru含量为1.0%-4.0%(质量分数,下同)的Ru/bauxite催化剂和Ru含量为2.0%的Ru/Al2O3催化剂,以水煤气变换反应为探针反应,考察了催化剂性能.利用X射线荧光元素分析(XRF)、X射线粉末衍射(XRD)、低温N2物理吸附、H2程序升温还原(H2-TPR)以及CO程序升温脱附(CO-TPD)等对载体和催化剂样品进行表征.结果表明,不同Ru含量的Ru/bauxite催化剂具有优异的水煤气变换制氢性能,优于Ru/Al2O3催化剂.其原因是铝土矿本身含有的Fe2O3与负载的Ru之间发生了相互作用,降低了Fe2O3还原温度,提高了对CO的吸附能力且降低了CO的脱附温度,进而提高了催化剂的水煤气变换反应性能.     

用于生物柴油清洁生产的磁性固体催化剂CaO/MgO/Fe_3O_4

制备了具有磁性和催化活性的双功能催化剂CaO/MgO/Fe3O4,用于催化花生油酯交换制备生物柴油的清洁生产过程。对CaO/MgO/Fe3O4进行了XRD、TEM、FT-IR和磁性等表征分析,探讨了CaO/MgO/Fe3O4催化剂的重复利用性能。结果表明,用Mg(Ac)2溶液等体积浸渍磁性基质Fe3O4,在N2气氛中600℃焙烧2 h,可得到具有磁性的载体5%MgO/Fe3O4;再用Ca(Ac)2溶液等体积浸渍MgO/Fe3O4,并在N2气氛中700℃煅烧,得到具有磁性且催化活性较高的催化剂10%CaO/MgO/Fe3O4。该催化剂具有核壳结构,磁核平均直径约为35 nm。在催化剂用量10%,醇油摩尔比12∶1,反应温度65℃,反应2 h的条件下酯交换转化率可达90%以上。在磁场的吸引下该催化剂能快速与反应体系分离,催化剂回收率达90%。但CaO/MgO/Fe3O4重复利用性能较差,其原因是在搅拌反应过程中催化活性组分逐渐从催化剂上脱落所致。     

Ce0.67Zr0.33O2对CH4燃烧催化剂Fe2O3/Al2O3的改性作用

固定n(Ce)/n(Zr)比为0.67/0.33, 用共沉淀法制得一系列CeO2-ZrO2-Al2O3固溶体. 采用这些固溶体作载体, 以Fe2O3为活性组分, 用浸渍法制备了一系列催化剂. BET结果显示, 将适量Ce0.67Zr0.33O2引入到Al2O3载体中有助于催化剂保持较高的比表面积. TPR结果显示, 载体中引入适量的Ce0.67Zr0.33O2可以改善催化剂的氧化还原性能. XRD结果表明, Fe2O3在CeO2-ZrO2-Al2O3载体上呈现出良好的分散状况, 老化前后催化剂的晶相结构基本无明显变化. 特别是当载体中m(Ce0.67Zr0.33O2)∶m(Al2O3)的值为1∶2时, Fe2O3/CeO2-ZrO2-Al2O3催化剂在甲烷催化燃烧中显示出最佳的催化性能和抗高温老化性能.     

负载型ZrO_2催化苯甲醛Meerwein-Ponndorf-Verley反应中的载体效应(英文)

采用浸渍法制备了Si-MCM-41和Al-MCM-41(Si/Al=50)介孔分子筛,SiO2,γ-Al2O3及MgO等负载的ZrO2催化剂,考察了其在以异丙醇为氢源苯甲醛Meerwein-Ponndorf-Verley(MPV)还原反应中的催化活性,并与纯ZrO2的催化活性进行对比.同时,采用X射线衍射、N2吸脱附法、X射线光电子能谱、紫外-可见漫反射光谱和吡啶原位吸附红外光谱等手段表征了催化剂.结果表明,ZrO2负载于Si-MCM-41,Al-MCM-41和SiO2后,催化活性明显提高,这归因于ZrO2与载体间存在强相互作用形成ZrOSi键,使催化剂表面ZrOH数量显著增多,Lewis酸中心强度增强,并出现Brnsted酸中心,三种催化剂的活性高低次序是5%ZrO2/Si-MCM-415%ZrO2/Al-MCM-415%ZrO2/SiO2.而5%ZrO2/Al2O3和5%ZrO2/MgO基本无催化活性,可归因为ZrO2与γ-Al2O3的弱相互作用使5%ZrO2/Al2O3的酸性与γ-Al2O3类似,ZrO2与MgO的强相互作用使5%ZrO2/MgO基本无酸性.     

负载型ZrO2催化苯甲醛Meerwein-Ponndorf-Verley反应中的载体效应（英文）

采用浸渍法制备了Si-MCM-41和Al-MCM-41(Si/Al=50)介孔分子筛,SiO2,γ-Al2O3及MgO等负载的ZrO2催化剂,考察了其在以异丙醇为氢源苯甲醛Meerwein-Ponndorf-Verley(MPV)还原反应中的催化活性,并与纯ZrO2的催化活性进行对比.同时,采用X射线衍射、N2吸脱附法、X射线光电子能谱、紫外-可见漫反射光谱和吡啶原位吸附红外光谱等手段表征了催化剂.结果表明,ZrO2负载于Si-MCM-41,Al-MCM-41和SiO2后,催化活性明显提高,这归因于ZrO2与载体间存在强相互作用形成ZrOSi键,使催化剂表面ZrOH数量显著增多,Lewis酸中心强度增强,并出现Brnsted酸中心,三种催化剂的活性高低次序是5%ZrO2/Si-MCM-41>5%ZrO2/Al-MCM-41>5%ZrO2/SiO2.而5%ZrO2/Al2O3和5%ZrO2/MgO基本无催化活性,可归因为ZrO2与γ-Al2O3的弱相互作用使5%ZrO2/Al2O3的酸性与γ-Al2O3类似,ZrO2与MgO的强相互作用使5%ZrO2/MgO基本无酸性.     

太阳能甲烷重整中催化活性吸收体的表面特性

以AISI316泡沫金属为基体为太阳能甲烷重整反应制备出系列Ru基和Ni基催化活性吸收体(Ru/Al2O3/AISI316,Ni/Al2O3(MgO)/AISI316),着重利用XRD、TPR、TPD和CO2脉冲吸脱附等技术对所制整体式催化剂的表面特性进行了表征和分析.结果表明:以AISI316泡沫金属为基体可增加活性组分与涂层载体Al2O3的相互作用以及活性物种的分散度.对于Ni基催化活性吸收体,在涂层载体中添加MgO助剂可显著地提高Ni/Al2O3/AISI316的催化活性;Al2O3涂层载体含量的增加可提高活性组分NiO的分散性.相对Ni/Al2O3/AISI316,Ru/Al2O3/AISI316催化活性吸收体对CO2的吸附和活化能力更强,因而具有相对更高的催化活性.     

Ce0.67Zr0.33O2对CH4燃烧催化剂Fe2O3/Al2O3的改性作用

固定n(Ce)/n(Zr)比为0.67/0.33,用共沉淀法制得一系列CeO2-ZrO2-Al2O3固溶体.采用这些固溶体作载体,以Fe2O3为活性组分,用浸渍法制备了一系列催化剂.BET结果显示,将适量Ce0.67Zr0.33O2引入到Al2O3载体中有助于催化剂保持较高的比表面积.TPR结果显示,载体中引入适量的Ce0.67Zr0.33O2可以改善催化剂的氧化还原性能.XRD结果表明,Fe2O3在CeO2-ZrO2-Al2O3载体上呈现出良好的分散状况,老化前后催化剂的晶相结构基本无明显变化.特别是当载体中m(Ce0.67Zr0.33O2)∶m(Al2O3)的值为1∶2时,Fe2O3/CeO2-ZrO2-Al2O3催化剂在甲烷催化燃烧中显示出最佳的催化性能和抗高温老化性能.     

Ru-La_2O_3/γ-Al_2O_3催化剂合成、表征及CO选择氧化

采用浸渍法制备系列Ru-La2O3/γ-Al2O3复合氧化物催化剂,通过XRD、H2-TPR、CO-TPR、XPS、BET等方法对催化剂进行表征,考察La2O3的加入量、预处理方法对催化剂上CO选择氧化性能的影响.结果表明,110-170℃时Ru1La6/Al2O3催化剂上CO转化率达到99%以上,氧气利用率达55.7%以上.和Ru/Al2O3相比,Ru1La6/Al2O3催化剂在较低温度具有高活性,活性温度区间变宽.适量La2O3的加入促进了活性组分在载体表面分散,提高了催化剂的活性.经氢气预处理的Ru1La6/Al2O3催化剂活性最佳,催化剂上Ru物种结合能降低,表面钌物种活性位增多,且表面晶格氧浓度增大,更有利于CO气体在催化剂表面上的氧化反应.     

费-托合成Fe1-xO基熔铁催化剂的研究

 采用高温熔融法制备了用于费-托合成的Fe1-xO基熔铁催化剂,考察了其在n(H2)/n(CO)=2,温度573 K,压力1.4 MPa和空速为12?600 h-1下的催化性能. 结果表明,与Fe3O4基熔铁催化剂相比,Fe1-xO基熔铁催化剂具有较高的催化F-T合成反应的活性、较低的WGS反应选择性和较强的加氢能力. XRD结果表明,经F-T反应后的熔铁催化剂存在Fe5C2和Fe3O4两种物相,但Fe1-xO基熔铁催化剂中Fe5C2的晶粒尺寸小于Fe3O4基熔铁催化剂中Fe5C2的晶粒尺寸.     

Secondary reactions of ethylene and propylene in the Fischer-Tropsch synthesis on cobalt-aluminum and cobalt-chromium catalysts

The only secondary reaction of olefins in the Fischer-Tropsch synthesis on Co/SiO₂·Al(III) and Co/SiO₂·Cr(III) with 2.7·10⁻⁶ and 4.0·10⁻⁶ g-ion/m² cation concentration in the support matrix, respectively, is dimerization of ethylene to give a four-carbon intermediate, which participates in the growth of C-C bond chains according to the classical FT synthesis mechanism. When the chromium concentration is increased by a factor of 1.7, secondary ethylene reactions occurring on the acid sites of the catalyst are also observed. When the aluminum concentration is increased by a factor of 3.4, we observe the oligomerization of ethylene and propylene. The secondary reactions of ethylene mainly result in linear hydrocarbons, while oligomerization involving propylene gives a significant amount of branched hydrocarbons. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 44, No. 2, pp. 115–120, March–April, 2008.     

Chain termination mechanism in the Fischer-Tropsch synthesis on a Co/SiO<Subscript>2</Subscript>Zr(IV) catalyst at elevated pressure

The mechanism for the formation of C₂₊ paraffins differs from the mechanism for the formation of methane. While methane is obtained due to hydrogenation of methyl groups, C₂₊ hydrocarbons are formed as the result of the conversion of alkyl intermediates into hydroalkene intermediates, which can decompose to give olefins or undergo hydrogenation to give saturated hydrocarbons. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 44, No. 3, pp. 175–179, May–June, 2008.     

Catalytic Deoxygenation of Xylitol to Renewable Chemicals: Advances on Catalyst Design and Mechanistic Studies

Xylitol is commonly known as one of the top platform intermediates for biomass conversion. Catalytic deoxygenation of xylitol provides an atomic and energetic efficient way to produce a variety of renewable chemicals including ethylene glycol, 1,2‐propanediol, lactic acid and 1,4‐anhydroxylitol. Despite a few initial attempts in converting xylitol into those products, improving catalyst selectivity towards C?O and C?C cleavage reactions remains a grand challenge in this area. To our best knowledge, there is lack of comprehensive review to summarize the most recent advances on catalyst design and mechanisms in deoxygenation of xylitol, offering important perspective into future development of xylitol transformation technologies. Therefore, in this mini‐review, we have critically discussed the conversion routes involved in xylitol deoxygenation over solid catalyst materials, the nanostructures of supported metal catalysts for C?H, C?C and C?O bond cleavage reactions, and mechanistic investigation for xylitol conversion. The outcome of this work provides new insights into rational design of effective deoxygenation catalyst materials for upgrading of xylitol and future process development in converting hemicellulosic biomass.     

Ruthenium(III) Catalyzed Oxidation Of Ethylenediaminetetraacetic Acid By N-Bromosuccinimide In Aqueous Alkaline Medium – A Kinetic And Mechanistic Study

The formation mechanism of microheterogeneous hydrogenation catalysts based on phosphinepalladium (II) complexes has been considered. According to elemental analysis, X-ray diffraction, electron microscopy, NMR, and IR spectroscopy, the catalyst is a nanoscale palladium organophosphorus matrix and (or) palladium phosphide with immobilized palladium clusters. This revised version was published online in June 2006 with corrections to the Cover Date.     

DFT研究Schrock钼催化剂催化的丙烯和丙烯腈复分解反应机理

使用密度泛函理论方法研究了Schrock钼催化剂催化的丙烯和丙烯腈复分解反应机理。研究结果表明：所有金属环丁烷中间体都是三角双锥结构,配体OCF₃和NMe占据三角双锥结构的2个顶点。大部分过渡态具有与金属环丁烷中间体相似的结构特征。Schrock钼催化剂催化的丙烯和丙烯腈的复分解反应包含了3个反应步骤。基于不同通道过渡态结构的相对能量,我们预测顺式和反式产物的产率为9∶1,这个结果与实验事实吻合得很好。     

臭氧在金属氧化物上的分解机理

臭氧分解反应在环境科学中具有重要理论和实际意义。本文对近期相关文献进行了综述，对臭氧在固体催化剂表面上的吸附和分解过程进行了总结，并结合我们的实验对其分解机理进行了探讨。     

Polymerization kinetics of octene-1 catalyzed by metallocene methylaluminoxane investigated with attenuated total reflectance fourier transform infrared (ATR-FT-IR) spectroscopy

The kinetic parameters have been measured for octene-1 solution polymerization at 120°C catalyzed by zirconocene with the cocatalyst methylaluminoxane. The polymerizations were performed in an attenuated total reflectance (ATR) reaction cell. The progress of the reactions were followed by observing the disappearance of octene-1 using the 910 cm^?1 band measured by FT-IR spectroscopy. The dependence of the reaction rate, R_p, on catalyst concentration and cocatalyst/catalyst ratio was examined. The catalyst deactivation mechanism was studied by fitting the experimental data to mathematical models involving second-order propagation and either first or second order catalyst deactivation. Second-order catalyst deactivation provided a much better fit. The calculated deactivation rate constant, k_d, is 21 (Ms)^?1. This model is used to determine the propagation rate constant for Al/Zr = 4 × 10³ as k_p = 19.9 (M s)^?1. A decrease in Al/Zr = 3 × 10² lowered the propagation rate constant, k_p, to 9.6 (M s)^?1 indicating that less than 50% of the initial Zr is active at this Al/Zr ratio.     

聚丙烯催化剂的聚合机理研究进展

评述了自二十世纪五十年代至今近五十多年聚丙烯催化剂的几个重要发展阶段,着重介绍两类(单活性中心与多活性中心)三种聚丙烯催化剂,即Ziegler-Natta催化剂、茂金属催化剂和后过渡铁金属催化剂催化丙烯聚合的机理。     

Kinetics and Mechanism of Action of a Novel Catalyst for Wood Delignification in Alkaline Medium

A novel catalyst of wood delignification (DC), which is produced by chemical interaction of amine and elemental sulfur in superbase medium, has been synthesized. The kinetics and mechanism of the novel catalyst action have been investigated in wood delignification.     

WO3改性CeO2-TiO2催化剂的低温NH3-NO/NO2 SCR活性和机理研究

在铈钛基NH3-SCR催化材料中,改性元素对催化材料的酸性位和氧化还原性能的影响较大.本文采用过量浸渍法分别制备了CeO2-TiO2(CeTi)和CeO2/WO3-TiO2(CeWTi)催化剂,研究了CeWTi催化材料结构、酸性位及氧化还原性能对NH3-NO/NO2 SCR反应性能的影响.结果发现,CeTi和CeWTi样品均有较优异的NH3-NO/NO2 SCR催化性能,后者略高.WO3的加入增加了催化材料的表面酸性,对其氧化还原性能影响不大.通过对反应中间物种NH4NO3的研究,发现NH4NO3的分解主要与氧化还原性能相关,而NO还原NH4NO3的反应需要氧化还原能力和酸性位共同作用,即在氧化还原性能差异不大的条件下,酸性对该反应起到重要作用.而该反应也是NH3-NO/NO2 SCR的限速步骤,这是CeWTi催化材料活性高于CeTi催化材料的原因.同时,为了获得NH3-NO/NO2 SCR反应的高活性,NO2:NO比例宜为1:1.然而现实情况中,预氧化催化材料的氧化活性、NOx浓度、温度等变量使得准确控制NO2的比例较难,因此,深入了解NO2浓度对NH3–NO/NO2 SCR反应的影响至关重要.本文探讨NO2:NO的比例、O2浓度等对NH3-NO/NO2 SCR反应性能的影响;并研究了不同NO2含量条件下NH3-NO/NO2 SCR反应网络.通过分析CeWTi材料上NH3-NO/NO2 SCR反应网络可知,当NO与NO2比例为1:1时,NH3-SCR催化活性最高,并以快速SCR形式进行;当NO与NO2比例为1:1消耗完全之后,剩余的NO或NO2各自独立以标准或慢速SCR进行,不影响其本来的反应活性.催化材料的标准SCR、快速SCR和慢速SCR均取决于材料表面酸度和氧化还原性能,但快速SCR和慢速SCR对材料这两方面性能的要求相对较低.同时O2并不参与快速和慢速SCR,而NO2可以取代O2作为SCR反应中主要的氧化剂,氧化Ce4+为Ce3+,甚至比O2和NO再氧化活性位的能力更强,保持催化材料的高催化活性.低温条件时,慢速SCR和快速SCR反应均在材料表面生成硝酸铵中间物种,但由于慢速SCR气氛中缺乏NO将硝酸铵还原,进而引发快速SCR反应,因此材料表面快速SCR的NOx转化率要高于慢速SCR反应;高温条件下,由于硝酸铵容易热分解,导致硝酸铵的抑制效应不太明显.NH4NO3分解是NO2含量升高后N2O的形成的主要途径.