质子交换膜燃料电池Pd修饰Pt/C催化剂的电催化性能

通过对Pt催化剂表面进行Pd修饰提高质子交换膜燃料电池阴极催化剂的氧还原反应(ORR)活性. 采用乙二醇还原法制备了不同比例的Pd修饰Pt/C催化剂. 透射电镜(TEM)和X射线衍射(XRD)测试结果表明, 制备的催化剂贵金属颗粒粒径主要分布在1.75～2.50 nm之间, 并均匀地分散在碳载体表面. 循环伏安方法(CV)研究表明Pd修饰Pt/C催化剂的电化学活性面积低于传统的Pt/C催化剂. 但通过旋转圆盘电极(RDE)测试研究发现, 制备的催化剂具有比传统Pt/C催化剂高的ORR活性.     

不同结构及氮掺杂NiO/rGO氧还原催化剂的制备与性能研究（英文）

本文以还原氧化石墨烯(rGO)为载体制备了片状NiO/rGO和球形NiO/N-rGO结构的氧还原催化剂.通过X-射线衍射(XRD)、Raman(拉曼)测试、X-射线光电子能谱(XPS)、扫描电子显微镜(SEM)和透射电子显微镜(TEM)等方法表征了两种催化剂的结构和形貌.采用循环伏安法(CV)、Tafel曲线、线性扫描伏安法(LSV)、旋转圆盘电极(RDE)和旋转环盘电极(RRDE)等技术测试研究了两种催化剂的电化学催化氧还原性能.研究结果表明,球形NiO/N-rGO催化剂催化氧还原的峰电流密度和起始电位(0.89 V vs. RHE)与商业化的Pt/C(20%)催化剂相近.旋转圆盘电极(RDE)和旋转环盘电极(RRDE)测试证明,在碱性电解液中NiO/rGO和NiO/N-rGO催化的氧还原反应均主要通过4-电子途径反应途径发生,球形NiO/N-rGO催化剂展现出替代Pt/C基催化剂的潜力.     

无机胶体法制备Pt/C催化剂及其性能表征

采用无机胶体法制备用于质子交换膜燃料电池(PEMFC)的Pt/C催化剂。研究了影响PtO₂胶体生成和稳定性的因素(溶液的pH值、浓度和温度条件等)以及不同还原剂浓度对Pt/C催化剂性能的影响。透射电子显微镜测试结果表明，采用经优化的工艺条件所制备的Pt/C催化剂平均粒径为3 nm，且分散性好、粒度均匀。X-射线衍射分析表明，催化剂中Pt(111)晶面的相对含量较高，有利于加速氧还原反应。单体PEMFC的电压/电流密度曲线测试表明，所制备的Pt/C催化剂具有良好的电化学性能。     

碳化钨用作质子交换膜燃料电池催化剂载体的抗氧化性能

 采用还原碳化法制备了碳化钨样品,并用原位还原法担载Pt粒子得到Pt/WxCy催化剂. 利用计时电流技术对Pt/WxCy和常规Pt/C催化剂进行氧化处理,并用循环伏安法测试了氧化前后两种催化剂的电化学活性面积. 将两种催化剂制成单电池,对比研究了其氧化后的性能衰减. 结果表明, Pt/WxCy催化剂制成的单电池抗氧化能力显著高于普通Pt/C制成的单电池.     

不同结构及氮掺杂NiO/rGO氧还原催化剂的制备与性能研究

本文以还原氧化石墨烯（rGO）为载体制备了片状NiO/rGO和球形NiO/N-rGO结构的氧还原催化剂. 通过X-射线衍射（XRD）、Raman（拉曼）测试、X-射线光电子能谱（XPS）、扫描电子显微镜（SEM）和透射电子显微镜（TEM）等方法表征了两种催化剂的结构和形貌. 采用循环伏安法（CV）、Tafel曲线、线性扫描伏安法（LSV）、旋转圆盘电极（RDE）和旋转环盘电极（RRDE）等技术测试研究了两种催化剂的电化学催化氧还原性能. 研究结果表明,球形NiO/N-rGO催化剂催化氧还原的峰电流密度和起始电位（0.89 V vs. RHE）与商业化的Pt/C（20%）催化剂相近. 旋转圆盘电极（RDE）和旋转环盘电极（RRDE）测试证明,在碱性电解液中NiO/rGO和NiO/N-rGO催化的氧还原反应均主要通过4?鄄电子途径反应途径发生,球形NiO/N-rGO催化剂展现出替代Pt/C基催化剂的潜力.     

高载量PtNi金属间化合物的氧还原电催化性能

采用改进的多元醇法制备了PtNi(原子比1∶1)质量分数为60%的高金属载量碳载PtNi合金(PtNi/C), 通过在450 ℃下退火处理获得了碳载PtNi金属间化合物氧还原电催化剂. 该催化剂对氧还原的质量比活性和面积比活性分别是商业化Pt/C(JM Pt/C)催化剂的1.66和2.3倍; 并且加速耐久性测试后PtNi金属间化合物催化剂的质量比活性仍与Pt/C的初始性能相当, 耐久性得到了大幅提升. PtNi/C金属间化合物催化剂氧还原活性和稳定性的提高归因于PtNi的有序原子排布结构及催化剂表面零价金属含量的提高.     

氮掺杂石墨烯的一步法低温合成及用作微生物燃料电池阴极催化剂的产电特性

利用爆炸法低温合成了氮掺杂石墨烯(NG),并通过高分辨透射电子显微镜、X射线光电子能谱仪、Raman光谱仪以及X射线衍射仪对其进行了表征.电化学性能检测结果表明,所合成的NG在中性磷酸盐电解液中具有优异的氧还原催化活性,完全能够与贵重金属铂催化剂(Pt/C)相媲美,氧还原催化稳定性甚至优于Pt/C.当NG用作微生物燃料电池(MFCs)的阴极氧还原催化剂时,在外阻为1000Ω情况下,MFCs的最大功率密度为1345 mW/m2,产电稳定性优于以Pt/C为阴极催化剂的MFCs,可以成为Pt催化剂的理想替代品.     

Fe对Pt-Fe/C催化剂电催化氧还原反应活性的影响

制备了用作直接甲醇燃料电池的碳载Pt-Fe(Pt-Fe/C)阴极催化剂, X射线能量色散谱(EDX)、X射线衍射谱和电化学测量的结果表明, 在Pt-Fe/C催化剂中, Fe以3种形式存在. 质量分数大约为20％的Fe进入Pt的晶格, 形成Pt-Fe合金, 质量分数大约为80％的Fe没有进入Pt的晶格而以Fe和Fe2O3的形式单独存在. 该催化剂经酸处理后, 非合金化Fe和Fe2O3被溶解, 而使Pt-Fe/C催化剂的电化学活性比表面积要比未经酸处理前的增加约30％左右, 导致Pt-Fe/C催化剂对氧还原的电催化活性优于未经酸处理前的Pt-Fe/C催化剂. 研究结果表明, Pt-Fe/C催化剂的电化学活性比表面积对氧还原的电催化活性起重要的作用, 另外, 只有与Pt形成合金的Fe能提高Pt对氧还原的电催化活性, 而非合金化的Fe对Pt催化剂对氧还原的电催化活性基本没有影响.     

炭黑负载Pt-Sn双金属催化剂对乙醇的电催化氧化性能

采用一步还原法(乙二醇为还原剂)与两步还原法(在聚乙烯吡咯烷酮PVP保护下,先用硼氢化钠还原制备Sn溶胶,沉积Pt后用乙二醇还原)制备了炭黑负载Pt-Sn双金属催化剂,利用循环伏安法和计时电流法考察了催化剂制备方法、Pt/Sn原子比、溶液p H值、PVP/Sn质量比、反应介质等对乙醇室温电催化氧化活性和稳定性的影响.以X光衍射、透射电镜及电化学活性面积测定对所得催化剂进行了表征.发现引入Sn明显提高了Pt催化剂对乙醇的电催化活性与稳定性,两步还原法得到的Pt3Sn/C催化剂具有更小的颗粒尺寸,更大的电化学活性面积及更高的乙醇氧化活性与稳定性.与酸性介质相比,该催化剂在碱性介质中的电化学活性更好.     

Pt纳米颗粒在氮掺杂空心碳微球上的高分散负载及其氧还原性能

通过热解自聚合多巴胺法制备了氮掺杂空心碳微球(N-HCMS), 并采用微波辅助乙二醇还原方法把Pt纳米粒子负载于N-HCMS上制得了Pt/N-HCMS催化剂. 催化剂的表面形貌、晶体结构及其比表面积和孔径分布等分别采用扫描电子显微镜、透射电子显微镜、X射线衍射仪及比表面分析仪等进行表征. 采用循环伏安法和线性扫描伏安法研究了Pt/N-HCMS 催化剂在酸性条件下的电催化氧还原性能. Pt/N-HCMS 催化剂由于Pt纳米粒子的均匀分散、N-HCMS载体的快速电子传递及其独特的微孔和中空结构而具有很高的电催化氧还原活性, 其质量比活性是E-TEK Pt/C 催化剂的近两倍. Pt/N-HCMS 催化剂还具有优良的稳定性. 本工作对于开发高性能的燃料电池阴极催化剂具有重要意义.     

PS-b-PEO模板法制备Pt纳米线

以PS-b-PEO纳米孔膜为基体电极,采用电沉积技术制备了Pt纳米线,用扫描电化学显微镜(SECM)、扫描电镜(SEM)和X-射线能谱(EDS)分析法表征了基体电极和Pt纳米线。利用循环伏安法考察了Pt纳米线的电化学性能。实验结果表明,Pt纳米线对甲酸氧化表现出优异的电催化活性。此外,Pt纳米线具有良好的稳定性和重现性,可望用于实际样品中甲酸的测定。     

Polyaniline Nanowires-Based Electrochemical Immunosensor for Label Free Detection of Japanese Encephalitis Virus

Polyaniline (PANI) conducting polymers have attracted increasing interest as a transducer material for biosensors applications. In this study, we demonstrate the use of PANI nanowires (NWs) as immobilization platforms in the configuration of an electrochemical immunosensor for label free detection of Japanese encephalitis virus. The PANI NWs were synthesized on the surface of an interdigitated platinum (Pt) microelectrode via electrochemical growth. The morphology and characteristics of the PANI NWs on the Pt microelectrode were verified by scanning electron microscopy and Fourier transform infrared spectroscopy. The anti- Japanese encephalitis virus polyclonal IgG antibody was then covalently immobilized on the PANI NWs-coated Pt microelectrode by using 1-ethyl-3-(3-dimethyaminopropyl) carbodiimide (EDC) and N-hydroxysuccinimde (NHS). The detection of Japanese encephalitis virus antigens was analyzed by electrochemical impedance spectroscopy (EIS). The developed PANI NWs-based electrochemical immunosensor could detect the Japanese encephalitis virus with a detection limit below 10 ng/ml. The results from EIS analysis also indicate that when the PANI NWs were exposed to nonspecific molecules, a negligible response was found, and it did not impact to the specificity of the sensor in the virus detection. This work shows the potential use of PANI NWs in electrochemical immunosensors for label free detection of other pathogens and small biomolecules.     

预制铂纳米颗粒对质子交换膜燃料电池用铂纳米线阴极的结构影响

铂纳米线（Pt NWs）由于其独特的结构特点,比商业Pt/C具有更高的氧还原反应（ORR）比活性。在本工作中,我们将预先制备好的铂纳米颗粒（Pt NPs）引入到碳基体中,用于诱导生长Pt NWs,获得了均匀分布Pt NWs的阴极。通过改变Pt NP载量（0~0.015 mg·cm^-2）和Pt NP来源（不同Pt含量的Pt/C）研究了所制备阴极的结构和性能。用扫描电镜对阴极表面进行了表征,并用透射电镜和X射线衍射分析了Pt NW的形貌和晶体结构。在单电池中分别进行了极化曲线和循环伏安曲线测试。当Pt NP来源为40% Pt/C且其载量为0.005 mg·cm^-2时,制备的Pt NW阴极具有最佳的单电池性能和最大的电化学表面积（ECSA）。最后,提出了预制Pt NP影响Pt NWs分布的可能机制。     

Fabrication of PtRu/Ru core–shell nanowires by exchanging Ru phases

In this study, we successfully fabricated PtRu/Ru core–shell nanowires (NWs) prepared from as-spun Ru/Pt core–shell NWs via a co-electrospinning method. Their formation mechanism together with the structural characteristics, morphology, and composition of the resulting PtRu/Ru core–shell NWs was elucidated by means of scanning electron microscopy (SEM), transmission electron microscopy (TEM) with energy dispersive X-ray spectroscopy (EDS), and X-ray diffraction (XRD). PtRu/Ru core–shell NWs fabricated from as-spun Ru/Pt core–shell NWs were formed as a result of interdiffusion between Ru atoms and Pt atoms during calcination after co-electrospinning.     

Synthesis of silver nanowires and their applications in the electrochemical detection of halide

A silver nanowires modified platinum (Ag NWs/Pt) electrode was developed for simultaneous and selective determination of chloride, bromide and iodide ions by cyclic voltammetry in aqueous solutions. Silver nanowires were synthesized by an l-cysteine-assisted poly (vinyl pyrrolidone) (PVP)-mediated polyol route. X-ray diffraction (XRD) and scanning electron microscopy (SEM), transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDS) were employed to investigate the prepared nanowires. The intrinsic high surface area and the fast electron transfer rate ascribed from the nanowire structure could further improve halide detection performance. The determination was based on measurement of the well-separated oxidation peak currents of respective silver halides formed on the surface of silver during an anodic potential sweep. The concentration range was linear from 50 μM to 20.2 mM for bromide and iodide and 200 μM to 20.2 mM for chloride, and the sensitivity was 0.059 μA/mM, 0.042 μA/mM and 0.032 μA/mM for chloride, bromide and iodide, respectively. The correlation coefficient was 0.999 in each case. The Ag NWs/Pt electrode offered a useful platform for the development of a highly sensitive halide sensor.     

Composite of Pt–Ru supported SnO2 nanowires grown on carbon paper for electrocatalytic oxidation of methanol

Platinum–ruthenium (Pt–Ru) nanoparticles were successfully deposited, for the first time, on the surface of SnO₂ nanowires grown directly on carbon paper (Pt–Ru/SnO₂ NWs/carbon paper) by potentiostatic electrodeposition method. The resultant Pt–Ru/SnO₂ NWs/carbon paper composites were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD). The electrocatalytic activities of these composite electrodes for methanol oxidation were investigated and higher mass and specific activities in methanol oxidation were exhibited as compared to Pt–Ru catalysts deposited on glassy carbon electrode.     

氮化钛纳米线的结构特征及其对Ⅴ(Ⅱ)/Ⅴ(Ⅲ)的电极过程

Titanium nitride nanowires (TiN NWs) were directly prepared on a Ti foil by a hydrothermal method followed by nitridation in ammonia atmosphere. The composition, microstructure, and electrochemical properties of the TiN NWs were characterized using scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HR-TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), cyclic voltammetry(CV), and electrochemical impedance spectroscopy (EIS). The results show that the nanowires have diameters of 20-50 nm and are 5 μm long. The surfaces of the TiN NWs comprise Ti-N, Ti-O, and O-Ti-N chemical states. The electrochemical activity and reversibility for the electrode processes of Ⅴ(Ⅱ)/Ⅴ(Ⅲ) couple on the TiN NWs are significantly improved due to the introduced Ti-N, Ti-O, and O-Ti-N chemical states. The transfer resistance for the cathodic reduction of Ⅴ(Ⅲ) on the TiN NWs is about 20 times and 10 times smaller than on TiO₂ NWs and graphite electrodes, respectively. The rate constant of charge transfer on the TiN NWs electrode was determined to be 5.21×10^-4 cm·s_-1, which is about 5 times larger than the rate constant on graphite electrodes (9.63×10^-5 cm·s^-1).     

Electrochemical templating of metal nanoparticles and nanowires on single-walled carbon nanotube networks

The use of single-walled carbon nanotube (SWNT) networks as templates for the electrodeposition of metal (Ag and Pt) nanostructures is described. Pristine SWNTs, grown on insulating SiO2 surfaces using catalyzed chemical vapor deposition, served as the working electrode. In the simplest case, electrical contact was made by depositing a gold strip on the SWNT substrate (device 1). Deposition of Ag and Pt over extensive periods (30 s) resulted in a high density of particles on the SWNTs, with almost contiguous nanowire formation from the Au/SWNT boundary moving to isolated nanoparticles at further distances from the contact. For direct electrochemical studies of Ag and Pt nucleation, the assembly was coated in a resist layer and a small window opened up to expose only the electrically connected SWNTs to solution (device 2). In this case, the electrochemical signature in voltammetric and amperometric studies of metal deposition was due solely to processes at the SWNTs. Coupled with high-resolution microscopy measurements (atomic force microscopy and field emission scanning electron microscopy), this approach provided detail on the nucleation and growth mechanisms of Ag and Pt on SWNTs under electrochemical control. In particular, Ag growth was found to be rapid and progressive with an increasing nanoparticle density with time, whereas Pt deposition was characterized by lower nucleation densities and slower growth rates with a tendency for larger particles to be produced over long times.     

Fabrication of Hierarchically Structured MOF‐Co3O4 on Well‐aligned CuO Nanowire with an Enhanced Electrocatalytic Property

Engineering appropriate shape and size of three‐dimensional inorganic nanostructures materials is of one the main critical problems in pursuing high‐performance electrode materials. Herein, we fabricate a metal‐organic framework derived cobalt oxide (Co₃O₄) are grown on copper oxide nanowire (CuO NWs) supported on the surface of 3D copper foam substrate. The highly aligned CuO NWs were prepared by using electrochemical anodization of copper foam in ambient temperature and followed by MOF Co₃O₄ was grown via a simple in situ solution deposition then consequent calcination process. The obtained binder‐free 3D CuO NWs@Co₃O₄ nanostructures were further characterized by using X‐ray diffraction, X‐ray photoelectron spectroscopy, field‐emission scanning electron microscopy, and transmission electron microscopy. Furthermore, electrochemical sensing of glucose was studied by using Cyclic Voltammetry, and chronoamperometry techniques. Interestingly, 3D CuO NWs@Co₃O₄ electrode exhibits excellent performance for the oxidation of glucose compared with individual entities. The proposed sensor shows wide linear ranges from 0.5 μM to 0.1 mM with the sensitivity of 6082 μA/μM and the lowest detection limit (LOD) of 0.23 μM was observed with the signal to noise ratio, (S/N) of 3. The superior catalytic oxidation of glucose mainly is endorsed by the excellent electrical conductivity and synergistic effect of the Co₃O₄ and CuO NWs.     

Stereoaligned Epitaxial Growth of Single‐Crystalline Platinum Nanowires by Chemical Vapor Transport

Epitaxial Pt nanowire (NW) arrays are synthesized for the first time by a chemical vapor transport method by using a metal halide as a precursor. Here we report that the epitaxial growth direction of NWs can be steered by seed crystal morphology. Octahedral seeds grow into inclined NWs possessing six growth directions, whereas half‐octahedral seeds grow into vertical and horizontal NWs. Interfacial energies between the seed material and the substrate are critical in determining the morphology of seed crystals. We also demonstrate that non‐SERS‐active Pt NWs can show strong surface‐enhanced Raman scattering (SERS) spectra by placing them on Ag films. The active SERS observation would help to elucidate platinum‐catalyzed chemical reactions.