水热法合成CdS/ZnO核壳结构纳米微粒

以半胱氨酸镉配合物为前驱体,采用水热法合成CdS纳米微粒,并以ZnO对其进行表面修饰,形成具有核／壳结构的CdS／ZnO半导体纳米微粒,CdS纳米微粒表面经ZnO修饰后,其带边发射大大增强,透射电镜显示,110℃下反应4h所得的CdS／ZnO颗粒尺寸约为20nm,电子衍射表明其结构为六方相。     

Highly Stable CdSe/CdS/ZnS Fluorophores in Acidic Environment: Acile Preparation and Modification of Core/shell/shell Nanocrystals

We described a facile method for preparing CdSe/CdS/ZnS core/shell/shell nanocrystals from air-stable single source precursors.The single source precursors of cadmium ethylxanthate and zinc ethylxanthate were used to form CdS and ZnS shell layers in octadecene.An efficient modification of CdSe/CdS/ZnS nanocrystals was subsequently performed to obtain hydrophilic nanocrystal fluorophores with good stability in a pH range of 1.6-10.     

Ultrafast Carrier Dynamics in CdSe/CdS/ZnS Quantum Dots

The intra- and inter-band relaxation dynamics of CdSe/CdS/ZnS core/shell/shell quantum dots are investigated with the aid of time-resolved nonlinear transmission spectra which are obtained using femtosecond pump-probe technique. By selectively exciting the core and shell carrier, the dynamics are studied in detail. Carrier relaxation is found faster in the conduction band of the CdS shell (about 130 fs) than that in the conduction band of the CdSe core (about 400 fs). From the experiments it is distinctly demonstrated the existence of the defect states in the interface between the CdSe core and the CdS shell, indicating thatultrafast spectroscopy might be a suitable tool in studying interface and surface morphology properties in nanosystems.     

Single-source precursor route for overcoating CdS and ZnS shells around CdSe core nanocrystals

We reported a facile route for overcoating CdS and ZnS shells around colloidal CdSe core nanocrystals. To synthesize such double shelled core/shell nanocrystals, first, CdSe core nanocrystals were prepared in a much “greener” and cheap route, which did not involve the use of hazardous and expensive trioctylphosphine. Then, a low-cost and labor-saving route was adopted for the CdS and ZnS shell growth with the use of thermal decomposition of commercial available air stable single-source precursors cadmium diethyldithio-carbamate and zinc diethyldithiocarbamate in a non-coordinating solvent at intermediate temperatures. Powder X-ray diffraction patterns and transmission electron microscopy images confirm the epitaxial growth of the shell in the core/shell nanocrystals. The photoluminescence quantum yield of the resulting CdSe/CdS/ZnS core/shell nanocrystals can be as high as 90% in organic media and up to 60% after phase transfer into aqueous media. By varying the size of CdSe cores, the emission wavelength of the obtained core/shell nanostructures can span from 554 to 636 nm.     

聚吡咯/硫化镉核壳纳米线的制备及整流特性

以无机多孔氧化铝膜为模板,利用气相沉积和原位电化学沉积方法成功地制备了有机-无机杂化聚吡咯/硫化镉核壳纳米线;采用扫描电子显微镜和透射电子显微镜分析了聚吡咯/硫化镉核壳纳米线的表面形貌和微结构.结果表明,内部的聚吡咯纳米线紧紧依附在外部的硫化镉纳米管中,并且硫化镉纳米管被聚吡咯全部填充.与此同时,在聚吡咯/硫化镉核壳纳米线中,外部硫化镉壳与内部聚吡咯核之间存在电荷转移;聚吡咯和硫化镉之间形成有机-无机杂化的P-N界面,从而导致单根聚吡咯/硫化镉核壳纳米线显示出不同于外部壳和内部核的整流特性.     

Large-scale synthesis of nearly monodisperse CdSe/CdS core/shell nanocrystals using air-stable reagents via successive ion layer adsorption and reaction

Successive ion layer adsorption and reaction (SILAR) originally developed for the deposition of thin films on solid substrates from solution baths is introduced as a technique for the growth of high-quality core/shell nanocrystals of compound semiconductors. The growth of the shell was designed to grow one monolayer at a time by alternating injections of air-stable and inexpensive cationic and anionic precursors into the reaction mixture with core nanocrystals. The principles of SILAR were demonstrated by the CdSe/CdS core/shell model system using its shell-thickness-dependent optical spectra as the probes with CdO and elemental S as the precursors. For this reaction system, a relatively high temperature, about 220-240 degrees C, was found to be essential for SILAR to fully occur. The synthesis can be readily performed on a multigram scale. The size distribution of the core/shell nanocrystals was maintained even after five monolayers of CdS shell (equivalent to about 10 times volume increase for a 3.5 nm CdSe nanocrystal) were grown onto the core nanocrystals. The epitaxial growth of the core/shell structures was verified by optical spectroscopy, TEM, XRD, and XPS. The photoluminescence quantum yield (PL QY) of the as-prepared CdSe/CdS core/shell nanocrystals ranged from 20% to 40%, and the PL full-width at half-maximum (fwhm) was maintained between 23 and 26 nm, even for those nanocrystals for which the UV-vis and PL peaks red-shifted by about 50 nm from that of the core nanocrystals. Several types of brightening phenomena were observed, some of which can further boost the PL QY of the core/shell nanocrystals. The CdSe/CdS core/shell nanocrystals were found to be superior in comparison to the highly luminescent CdSe plain core nanocrystals. The SILAR technique reported here can also be used for the growth of complex colloidal semiconductor nanostructures, such as quantum shells and colloidal quantum wells.     

Solution-based II-VI core/shell nanowire heterostructures

We demonstrate the solution-phase synthesis of CdS/CdSe, CdSe/CdS, and CdSe/ZnTe core/shell nanowires (NWs). On the basis of bulk band offsets, type-I and type-II heterostructures are made, contributing to the further development of low-dimensional heteroassemblies using solution-phase chemistry. Core/shell wires are prepared by slowly introducing shell precursors into a solution of premade core NWs dispersed in a noncoordinating solvent at moderate temperatures (215-250 degrees C). Resulting heterostructures are characterized through low- and high-resolution transmission electron microscopy, selected area electron diffraction, and energy dispersive X-ray analysis. From these experiments, initial shell growth appears to occur through either Stranski-Krastanov or Volmer-Weber island growth. However, beyond a critical shell thickness, nucleation of randomly oriented nanocrystals results in a polycrystalline coat. In cases where overcoating has been achieved, corresponding elemental analyses show spatially varying compositions along the NW radial direction in agreement with expected element ratios. Electronic interactions between the core and shell were subsequently probed through optical studies involving UV-vis extinction spectroscopy, photoluminescence experiments, and transient differential absorption spectroscopy. In particular, transient differential absorption studies reveal unexpected shell-induced changes in core NW Auger kinetics at high carrier densities. Previously seen three-carrier Auger kinetics in CdS (bimolecular in CdSe) NWs were suppressed by the presence of a CdSe (CdS) shell. These observations suggest the ability to influence NW optical/electrical properties by coating them with a surrounding shell, a method which could be important for future NW optical studies as well as for NW-based applications.     

Aqueous synthesis of glutathione-capped CdTe/CdS/ZnS and CdTe/CdSe/ZnS core/shell/shell nanocrystal heterostructures

Here we demonstrate the aqueous synthesis of colloidal nanocrystal heterostructures consisting of the CdTe core encapsulated by CdS/ZnS or CdSe/ZnS shells using glutathione (GSH), a tripeptide, as the capping ligand. The inner CdTe/CdS and CdTe/CdSe heterostructures have type-I, quasi-type-II, or type-II band offsets depending on the core size and shell thickness, and the outer CdS/ZnS and CdSe/ZnS structures have type-I band offsets. The emission maxima of the assembled heterostructures were found to be dependent on the CdTe core size, with a wider range of spectral tunability observed for the smaller cores. Because of encapsulation effects, the formation of successive shells resulted in a considerable increase in the photoluminescence quantum yield; however, identifying optimal shell thicknesses was required to achieve the maximum quantum yield. Photoluminescence lifetime measurements revealed that the decrease in the quantum yield of thick-shell nanocrystals was caused by a substantial decrease in the radiative rate constant. By tuning the diameter of the core and the thickness of each shell, a broad range of high quantum yield (up to 45%) nanocrystal heterostructures with emission ranging from visible to NIR wavelengths (500-730 nm) were obtained. This versatile route to engineering the optical properties of nanocrystal heterostructures will provide new opportunities for applications in bioimaging and biolabeling.     

ZnO/CdS复合材料的合成与可见光催化性能

采用喷雾辅助气相沉积法在水热法合成的ZnO纳米线上沉积CdS纳米颗粒。采用X射线衍射仪（XRD）、激光拉曼仪（Raman）、扫描电镜（SEM）、透射电镜（TEM）、X射线光电子能谱分析谱（XPS）和紫外可见漫反射光谱等测试手段对复合光催化剂进行表征。结果表明,3~10 nm的CdS纳米粒子修饰在直径约为100 nm ZnO纳米线的表面。XPS和Raman表明复合材料中ZnO和CdS之间存在化学相互作用。可见光催化降解罗丹明B实验结果表明ZnO/CdS复合材料的催化性能优于单相CdS或ZnO,沉积时间为30 s合成的ZnO/CdS速率常数分别是CdS和ZnO的2.91和4.03倍,且具有较高的稳定性。ZnO/CdS复合材料光催化性能增强的可能原因为光吸收范围的拓展和光生载流子分离效率的提高。     

Intraband spectroscopy and band offsets of colloidal II-VI core/shell structures

The interband and intraband spectra of colloidal II-VI CdS and CdSe quantum dot cores and CdSZnSe, CdSCdSe, CdSeCdS, and CdSeZnSe core/shell systems are reported. Infrared absorption peaks between 0.5 and 0.2 eV are observed. The slope of the intraband energy versus the first interband absorption feature is characteristic of the relative band alignments of the materials constituting the core and the shell and it is analyzed within an effective mass model. The analysis provides a new estimate of the band gap of zinc blende CdSe as well as the band offsets in zinc blende and wurtzite CdSe, CdS, and ZnSe.     

Visual and trap emission spectrometric detections of Ag (I) ion with mesoporous ZnO/CdS@SiO2 core/shell nanocomposites

A new method for the preparation of mesoporous ZnO/CdS@SiO₂ core/shell nanostructure (CSN) has been developed. The mesoporous silica shells allow Ag⁺ to enter into the interior of the nanostructures to contact with ZnO/CdS core, accordingly causes the quenching of its band edge emission (475 nm) along with a simultaneous enhancement of red emission at around 595 nm. So, a novel visual fluorescence detection strategy for Ag⁺ ion is proposed based on a common core/shell Quantum dots nanostructure. Under optimal conditions, the enhanced fluorescence intensity at 595 nm increased linearly with the concentration of Ag⁺ ion ranging from 0.03 μM to 0.24 μM with a detection limit (3σ) of 3.3 nM.     

水溶性CdSe/CdS核壳纳米粒子制备的影响因素及其对CdSe/CdS光谱特性的影响

以半胱氨酸镉配合物为前体, 在水溶液中合成CdSe纳米粒子, 以CdS对其表面进行修饰, 得到具有核壳结构的CdSe/CdS 纳米粒子. 采用XRD, TEM表征其结构及形貌; 以荧光光谱研究了时间、pH值、壳量、壳前体加入方式、稳定剂用量等因素对CdSe/CdS光谱特性的影响.     

Highly efficient photoelectrochemical hydrogen generation using a ZnO nanowire array and a CdSe/CdS co-sensitizer

Highly efficient photoelectrochemical (PEC) hydrogen generation was achieved by fabricating CdSe deposited ZnO/CdS core/shell nanowire (NW) array photoanodes by a facile three-step solution-based method. Well-defined electrical pathways in 1-dimensional (1D) NW structures allowed efficient charge carrier collection, and CdSe/CdS co-sensitization enabled utilization of the visible region in the solar spectrum. PEC devices using CdSe/CdS/ZnO NW arrays showed improved absorption spectra, and they demonstrated a remarkable enhancement in PEC performance. Our proposed structure is a promising candidate photoanode for solar energy-to-hydrogen conversion devices.     

Epitaxial growth and photochemical annealing of graded CdS/ZnS shells on colloidal CdSe nanorods

We report the preparation and structural characterization of core/shell CdSe/CdS/ZnS nanorods. A graded shell of larger band gap is grown around CdSe rods using trioctylphosphine oxide as a surfactant. Interfacial segregation is used to preferentially deposit CdS near the core, providing relaxation of the strain at the core/shell interface. The reported synthesis allows for variation of the shell thickness between one and six monolayers, on core nanorods ranging from aspect ratios of 2:1 to 10:1. After an irreversible photochemical annealing process, the core/shell nanorods have increased quantum efficiencies and are stable in air under visible or UV excitation. In addition to their robust optical properties, these samples provide an opportunity for the study of the evolution of epitaxial strain as the shape of the core varies from nearly spherical to nearly cylindrical.     

室温水相合成CdTe/CdS核/壳结构量子点

开发了一种以聚乙烯吡咯烷酮为分散剂和稳定剂经条件温和的室温水相合成光谱可调的水溶性CdTe/CdS核/壳结构量子点的方法:向新鲜制备的CdTe量子点溶液中加入硫源,继续反应即可生成CdS壳层,通过控制硫源的浓度即可控制CdS壳层厚度,从而调节光谱性质和增强稳定性.采用XRD、TEM、HRTEM、荧光光谱以及紫外-可见光...     

Microstructure control of Zn/ZnO core/shell nanoparticles and their temperature-dependent blue emissions

The microstructure of the Zn/ZnO core/shell nanoparticles synthesized by laser ablation in liquid medium can be facilely controlled. With the surfactant concentration increased over the critical micelle concentration, the nanoparticle transformed from pure ZnO to a Zn/ZnO core/shell structure. Further, with a decrease of the applied laser power, the ZnO shell thickness was monotonously reduced till 2.5 nm and the ultrafine ZnO nanocrystals embedded in the nanoshells were also reduced till 1.5 nm, which induced the increase of the disorder degree of the nanoshell lattice. The controlling mechanism was discussed according to the competition of capping protection and the oxidation reaction of laser-induced plasma. Blue photoluminescence from the ZnO nanoshells was observed. The emission band exhibited abnormal red-blue shift and narrowing with increasing temperature. Such temperature-dependent behaviors can be well described by a localization model involving an interstitial zinc defect center. These results indicate that this method provides a convenient and universal way to obtain various metal/oxide core/shell nanoparticles with controllable microstructure, and it will be beneficial to an understanding of the physical origins of the blue emission in nanostructured ZnO as well as to extending its optical and electronic applications.     

Controllable Conversion of CdNCN Nanoparticles into Various Chalcogenide Nanostructures for Photo-driven Applications

Semiconductor nanocrystals of tunable shell/core configurations have great potential in photo-driven applications such as photoluminescence and photocatalysis, but few strategies realize a controllable synthesis with respect to both the size of the core and the shell with high crystallinity. Here, a new synthetic method based on cadmium cyanamide (CdNCN) nanoparticle anion exchange reactions was developed to access solid or hollow CdSe nanocrystals with tunable size and CdNCN@CdS heterostructures with modulated shell/core thickness. The gradual shift and narrow width of photoluminescence features demonstrate the high crystallinity and monodispersity of the resulting CdSe nanocrystals. In the CdNCN@CdS heterostructures, synergistic effects of the photocarrier separation is observed between the CdS shell and CdNCN core, which leads to great improvement in photocatalysis with optimized shell/core ratio.     

Semiconductor nanoparticle/polystyrene latex composite materials

Cadmium sulfide and cadmium selenide/cadmium sulfide core/shell nanoparticles stabilized with poly(cysteine acrylamide) have been bound to polystyrene (PS) latexes by three methods. First, anionic 5 nm diameter CdS particles were electrostatically attached to 130 nm surfactant-free cationic PS latexes to form stable dispersions when the amount of CdS particles was less than 10% of the amount required to form a monolayer on the surface of the PS particles or when the amount of CdS particles exceeded the amount required to form a monolayer on the PS particles. Transmission electron microscopy (TEM) showed nanoparticles on the surface of the latex particles. Fluorescence spectra showed unchanged emission from the nanoparticles. Second, anionic, surfactant-free PS latexes were synthesized in the presence of CdS and CdSe/CdS nanoparticles. TEM showed monodisperse latex particles with trapped nanoparticles. Third, surfactant-stabilized latexes were synthesized by copolymerization of styrene with vinylbenzyl(trimethyl)ammonium chloride electrostatically bound to the CdSe/CdS nanoparticle surface. Brownian motion of the submicroscopic composite particles in water was detected by fluorescence microscopy.     

Band-edge ultrafast pump-probe spectroscopy of core/shell CdSe/CdS rods: assessing electron delocalization by effective mass calculations

CdSe/CdS dot/rods nanocrystals show interesting physical properties related to the band-alignment at the hetero-interface, which controls the band-edge electron delocalization over the rods. Here the differential transmission spectra of CdSe/CdS nanorod samples with different core sizes have been measured using excitation resonant to the core transition. The photo bleaching ratio between dot and rod transitions increases with the dot size, indicating a trend towards electron localization. This trend has been further quantified by performing effective mass calculations in which the conduction band misalignment was varied in order to reproduce the observed bleaching feature ratio. The best agreement was found for negligible conduction band misalignment for small dots of around 2.3 nm in diameter, and about -0.1 eV misalignment was estimated for the larger dots, above 3.5 nm in diameter. This shows that the band misalignment might be dependent on the geometry of the system, and we argue that this might be related to different strain developed at the hetero-interface.     

Determination of Albumin Using CdS/SiO2 Core/shell Nanoparticles as Fluorescence Probes

CdS quantum dots (QD) were capped with SiO₂ via a microemulsion method for reducing the toxicity and imparting the biocompatibility of the CdS QD. The resulting CdS/SiO₂ core/shell nanoparticles (NP) showed an improved water‐solubility and stability even in pH 4.0 acidic medium. Their fluorescence could be effectively enhanced in the presence of bovine serum albumin (BSA), due to the passivation effect of BSA on the surface of the NP. Furthermore, the concentration dependence of the fluorescence intensity obeys the Langmuir‐type binding isotherm. Thus a novel fluorescence enhancement method for the determination of BSA has been developed using the less‐toxic CdS/SiO₂ core/shell NP as probes. Under optimal conditions, the linear range of calibration curve is 0.6–30 µg·mL^?1, and the detection limit is 0.18 µg·mL^?1. Compared with the water‐soluble CdS NP without SiO₂ shell, the CdS/SiO₂ core/shell NP exhibited slightly lower fluorescence response to BSA as well as other coexisting substances, such as heavy and transition metals, due to the inhibition of SiO₂ shell. The proposed method was applied to the quantification of BSA in synthetic and serum samples with satisfactory results.