Ultrasound-assisted solvent extraction of total polycyclic aromatic hydrocarbons from mussels followed by spectrofluorimetric determination

An ultrasound-assisted solvent extraction procedure has been optimised to speed up total polycyclic aromatic hydrocarbons (T-PAHs) extraction from mussel soft tissue. The T-PAHs releases have been evaluated by spectrofluorimetry (excitation and fluorescence emission wavelengths of 300 and 382 nm, respectively, and using chrysene as calibrant). Variables such as sonication time, ultrasound frequency, n-hexane volume, dichloromethane volume, number of repeated extractions with n-hexane and number of repeated extraction with dichloromethane were simultaneously studied by applying a Plackett-Burman design (PBD) approach. Results showed that ultrasound frequency and n-hexane and dichloromethane volumes were statistically significant variables (confidence interval of 95%). These last two variables were finally optimised by using central composite designs (CCD), yielding optimum n-hexane and dichloromethane volumes of 2.5 and 6.5 ml, respectively. The lowest T-PAHs releasing at high ultrasound frequency (35 kHz) led to choice the lowest ultrasound frequency (17 kHz) to perform the extraction. Variables such as sonication time and number of repeated extraction with n-hexane or dichloromethane were statistically non-significant and they were fixed at 10 min and the extraction with n-hexane and dichloromethane were performed once. The limit of detection was 0.021 μg g⁻¹ (referred to dried mass), the repeatability of the overall method was 4.7% (n = 9) and the analytical recoveries were between 98 and 105%. The proposed method was finally applied to 16 mussel samples (Mytilus galloprovincialis) from Ría de Arousa estuary (Galicia, northwest Spain).     

Pressurised liquid extraction of polycyclic aromatic hydrocarbons from contaminated soils

The reliability and efficiency of the pressurised liquid extraction technique (PLE) for extracting polycyclic aromatic hydrocarbons (PAHs) from contaminated soil has been investigated. Experimental design was used to study the influence of seven extraction variables (sample load, solvents used, solvent ratios, pressure, temperature, extraction time, and rinse volume). The results show that large sample loads in combination with small solvent volumes may result in low extraction efficiency. They also indicate that the recovery of low-molecular-mass PAHs is reduced by low extraction temperatures. The exact settings of the other variables are, however, less significant for the extraction efficiency. Repeated extractions at optimised settings of the tested variables show that PLE is an exhaustive extraction technique that generally results in high yields. In addition, extraction of a certified reference material (CRM 103-100) revealed that the method is both accurate and precise. Another finding was that adding the internal standard on top of the soil in the extraction cell causes considerable over-estimation of the concentrations when large samples are extracted with small solvent volumes. This is because the PLE-cell resembles a chromatographic column, so compounds added to the top of the soil layer have a longer distance to travel through the soil compared to the average distance of the native compounds, which are distributed evenly throughout the column. We therefore recommend that the internal standard should be added to the extract immediately after the extraction or, alternatively, carefully mixed with the sample prior to extraction.     

Pressurised solvent extraction of nitrated derivatives of polycyclic aromatic hydrocarbons from roadside dust

An analytical method based upon the pressurised solvent extraction and gas chromatography and mass spectrometry (GC-MS) for analysis of nitrated derivatives of polycyclic aromatic hydrocarbons (nitro-PAHs) in roadside dust has been developed. Five nitro-PAHs (1-nitronaphthalene, 1-nitropyrene, 9-nitroanthracene, 2-nitrofluorene, 6-nitrochrysene) were chosen for this study because of their variable physical properties and effect on human health. Experiments with spiked inert matrix were used for the best extraction conditions finding. Different extraction conditions (temperature, pressure, solvents and duration of extraction cycle) were examined. The highest recoveries were observed at the extraction pressure of 14?MPa, temperature of 100°C and two cycles of 5?min extraction time, when dichloromethane was used as an extraction solvent. These conditions were applied to the extraction of nitro-PAHs from roadside dust. After extraction the nitro-PAHs fraction was isolated by the silica gel column chromatography. The GC-MS detector was used for analyses of the extracts. Recoveries of nitro-PAHs after extraction from roadside dust ranged from 60% for 9-nitroanthracene to 108% for 6-nitrochrysene.     

Extraction of polycyclic aromatic hydrocarbons and organochlorine pesticides from soils: a comparison between Soxhlet extraction, microwave-assisted extraction and accelerated solvent extraction techniques

The methods of simultaneous extraction of polycyclic aromatic hydrocarbons (PAHs) and organochlorine pesticides (OCPs) from soils using Soxhlet extraction, microwave-assisted extraction (MAE) and accelerated solvent extraction (ASE) were established, and the extraction efficiencies using the three methods were systemically compared from procedural blank, limits of detection and quantification, method recovery and reproducibility, method chromatogram and other factors. In addition, soils with different total organic carbon contents were used to test the extraction efficiencies of the three methods. The results showed that the values obtained in this study were comparable with the values reported by other studies. In some respects such as method recovery and reproducibility, there were no significant differences among the three methods for the extraction of PAHs and OCPs. In some respects such as procedural blank and limits of detection and quantification, there were significant differences among the three methods. Overall, ASE had the best extraction efficiency compared to MAE and Soxhlet extraction, and the extraction efficiencies of MAE and Soxhlet extraction were comparable to each other depending on the property such as TOC content of the studied soil. Considering other factors such as solvent consumption and extraction time, ASE and MAE are preferable to Soxhlet extraction.     

Extraction of polycyclic aromatic hydrocarbons from smoked fish using pressurized liquid extraction with integrated fat removal

Quantification of polycyclic aromatic hydrocarbons (PAHs) in smoked fish products often requires multiple clean-up steps to remove fat and other compounds that may interfere with the chemical analysis. We present a novel pressurized liquid extraction (PLE) method that integrates exhaustive extraction with fat retention in one single analytical step. The PLE parameters: type of fat retainer, flush volume, solvent composition, fat-to-fat retainer ratio (FFR), and the dimensions of the extraction cells were the most important factors for obtaining fat-free extracts with high recoveries of PAHs. A 100 mL extraction cell filled with 18 g activated silica gel, dichloromethane:hexane (15:85, v/v) as extraction solvent, FFR of 0.025 and 100% flush volume was the best analytical setup for integrated extraction and fat retention.The one-step procedure provided a more rapid and cost-efficient alternative with minimization of waste generation compared to the standard reference method that is based on a multi-step procedure. Furthermore, the analytical quality of the two methods are comparable, while the new integrated approach for extraction and cleanup is less prone to analytical errors (random and systematic) because of fewer analytical steps.     

Ultrasonic micellar extraction of polycyclic aromatic hydrocarbons from marine sediments

In this present study the extraction of polycyclic aromatic hydrocarbons (PAHs) from marine sediments with a micellar medium of Polyoxyethylene 10 lauryl ether by an ultrasound-assisted method has been studied. Factorial design experiments were used in order to optimize the extraction parameters: extraction time, surfactant concentration and surfactant volume:amount of sediment relationship. The results suggest that surfactant concentration is statistically the most significant factor. The analysis of extracts has been carried out by HPLC with UV detection. Fortified sediments gave an average recovery between 86.7 and 106.6%, with relative standard deviation of 2.02-6.83% for PAHs with a ring number higher than three.     

Fluidized-bed extraction of polycyclic aromatic hydrocarbons from contaminated soil samples

Summary Due to the carcinogenity and ubiquity of polycyclic aromatic hydrocarbons in the environment they are of ongoing interest to analytical chemistry. In this study, a comparison of the classic Soxhlet extraction and, fluidized-bed extraction, has been conducted. The extraction of polycyclic aromatic hydrocarbons by this technique has been optimized considering as experimental variables the variation of the number of extraction cycles and the holding time after reaching the heating temperature by means of a surface response design. The significance of the operational parameters of the fluidized-bed extraction on the performance characteristics has been investigated. For the determination of the analytes a selective clean-up of the extracts followed by a fast gas chromatography method with mass spectrometric detection was used, resulting in low limits of detection (0.2 pg μL⁻¹). The accuracy of the complete analytical method was established by extraction and analysis of reference materials.     

Ultrasound-assisted headspace ionic-liquid microextraction of polycyclic aromatic hydrocarbons at elevated temperatures

We have developed a method for ultrasound-assisted ionic-liquid (IL) microextraction at elevated temperatures. A sealed pipette tip was used to hold the IL. The polycyclic aromatic hydrocarbons naphthalene, acenaphthene and fluorene were headspace-extracted into a 30-μL volume of the IL at 60 °C. Cooling is not needed to control the temperature of the extraction solvent because it has almost zero vapor pressure. Following extraction, the analyte-loaded IL was submitted to HPLC with fluorescence detection. Under the optimal conditions, the limits of detection (at S/N?=?3) are 30, 30 and 10 ng L^?1 for naphthalene, acenaphthene and fluorene, respectively. Recoveries range from 86 to 110 %, and the extraction efficiency is better than previous methods by a factor of ~40. The technique was applied to the analysis of semivolatile pollutants (PAHs) in real aqueous samples.

Cyano-containing ionic liquids for the extraction of aromatic hydrocarbons from an aromatic/aliphatic mixture

Ionic liquids can replace conventional solvents in aromatic/aliphatic extractions, if they have higher aromatic distribution coef- ficients and higher or similar aromatic/aliphatic selectivities. Also physical properties, such as density and viscosity, must be taken into account if a solvent is applied in an industrial extraction process. Cyano-containing ionic liquids have a lower den- sity than the benchmark solvent sulfolane and a higher viscosity. Sulfolane is from a hydrodynamic point of view a better sol- vent than ionic liquids for the aromatic/aliphatic extraction. The most suitable ionic liquids for the extraction of aromatic hy- drocarbons from a mixture of aromatic and aliphatic hydrocarbons are [bmim]C(CN)3, [3-mebupy]N(CN)2, [3-mebupy]C(CN)3, [3-mebupy]B(CN)4 and [mebupyrr]B(CN)4. They have factors of 1.2-2.3 higher mass-based distribution coefficients than sul- folane and a similar or higher, up to a factor of 1.9 higher, aromatic/aliphatic selectivity than sulfolane. The IL [3-mebupy]N(CN)2 is a better extractant for the separation of toluene from a mixture of toluene/n-heptane in a pilot plant Ro- tating Disc Contactor (RDC) than sulfolane.     

Simultaneous extraction of polycyclic aromatic hydrocarbons and polychlorinated biphenyls in agricultural soils by pressurized liquid extraction and determination by gas chromatography coupled to tandem mass spectrometry

A simple and rapid method based on pressurized liquid extraction has been validated for the simultaneous extraction of polychlorinated biphenyls (PCBs) and polycyclic aromatic hydrocarbons (PAHs) from agricultural soil samples. Effective extraction was carried out in less than 17 min for all the studied compounds, and good recoveries were obtained for PAHs and PCBs, ranging from 70% to 112%, when blank samples were spiked at 2.5 μg kg⁻¹, except for naphthalene with recoveries close to 40%. The separation and determination were performed by gas chromatography coupled to tandem mass spectrometry using a triple quadrupole mass analyzer. The target compounds were detected by electron impact with selected reaction monitoring, and mass spectrometric conditions were optimized in order to increase selectivity and sensitivity. The developed method was validated, and matrix-matched calibration was used for quantification purposes. Repeatability and interday precision ranged from 0.9% to 16.8% and from 1.6% to 22.3%, respectively. Limits of quantification ranged from 0.07 to 2.50 μg kg⁻¹. The proposed method was applied to the analysis of agricultural soil samples collected from Almeria (Spain), and PAHs and PCBs were detected in some samples at concentrations ranging from 0.1 to 210 μg kg⁻¹.     

Differences in the yields of polycyclic aromatic hydrocarbons by pressurized liquid extraction and the Japanese official method

To improve the extraction of polycyclic aromatic hydrocarbons (PAHs) from sediment samples, we optimized the conditions of pressurized liquid extraction (PLE). The yields increased as the extraction temperature increased from 100 to 190 degrees C, but the effect of increasing pressure (from 15 to 20 MPa) was small. Parameters of 190 degrees C and 20 MPa, near the maximum of the equipment, gave the highest yield. Under these conditions, the yields of 17 PAHs were 1.5 - 34 times those obtained by the Japanese official method (shaking and ultrasonic extraction with acetone at room temperature).     

Microwave assisted extraction of polycyclic aromatic hydrocarbons from atmospheric particulate samples

For several years, microwave assisted extraction (MAE) was applied to extract organic compounds such as polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls, etc., from soils, sediments and standard reference materials. Very few authors applied this methodology for the extraction of PAHs from atmospheric particulate matter. In the present study, MAE of polycyclic aromatic hydrocarbons with hexane/acetone (1:1) from real atmospheric particulate samples was investigated and the effect of microwave energy and irradiation time studied. The yields of extracted compounds obtained by microwave irradiation were compared with those obtained using traditional Soxhlet extraction. MAE was evaluated using spiked real atmospheric particulate samples and two standard reference materials. Analytical determinations of PAHs were carried out by high performance liquid chromatography (HPLC) with ultraviolet and fluorescence detection. The best recoveries were achieved with a microwave energy of 400 W and an irradiation time of 20 min.     

Porous metal membranes for solid-phase extraction of polycyclic aromatic hydrocarbons

Solid-phase extraction (SPE) is one of the most important techniques for sample preparation, purification, concentration and cleanup. Membranes made from synthetic organic polymers, cellulose, or glass fibers are used for sample pretreatment. In this work, we report that a porous metal membrane, the metal filter in HPLC, was used as a novel kind of solid-phase extraction adsorbent material. To evaluate the performance of the porous metal membrane for the SPE, naphthalene, fluorene, anthracene, phenanthrene, fluoranthene, pyrene, chrysene, perylene and benzo(a)pyrene were selected as analytes. Several parameters that affected the extraction efficiency such as the extraction time, the concentration of NaCl, the extraction temperature and the agitation speed were optimized. The experimental result indicates that the porous metal membrane possesses high adsorption ability to the tested polycyclic aromatic hydrocarbons (PAHs). Under the optimum conditions, the detection limits of the developed method were in the range of 0.03-0.082 μg L(-1) (S/N = 5), and excellent linear correlations between peak area and concentration of PAHs were found over the range of 0.1-60 μg L(-1). The precisions (RSD) for five replicate extractions of the PAHs from sample solutions were in the range of 2.6-5.0%. The recoveries of the PAHs from tap water and river water samples spiked with 9 PAHs (20 μg L(-1) of each individual PAH) ranged from 83.0% to 112.5%. The porous metal membrane is durable, simple, inexpensive, reproducible and has a high adsorption ability for use in SPE of PAHs.     

Effect of moisture on the extraction efficiency of polycyclic aromatic hydrocarbons from soils under atmospheric pressure by focused microwave-assisted extraction

The performance of a large commercial chromatographic column was investigated using a short pulse of a tracer and an extension of the reverse-flow technique. This technique permits separate determination of the unavoidable irreversible microscopic processes and the reversible effects of flow maldistribution, and allows for the separation of flow maldistribution in the flow distributors from flow maldistribution inside the packed bed. This analysis was performed on a 0.44 m Millipore IsoPak column using Cellufine GC 700, cellulosic-based media with an average particle diameter of 75 microm, for the stationary phase. The column efficiency was quantified by analysis of the effluent curve from a short pulse of a 5% aqueous acetone tracer. The study examined behavior of beds of different lengths (10-24 cm) and beds packed from different slurry concentrations (10-75% v/v). The slurry-packed columns were very uniform, and no significant macroscopic flow maldistribution was observed inside the column. The observed bed plate heights conformed to the predictions of available one-dimensional continuum models. Dispersion in the flow distributors was significant, corresponding to 15-25% of the intracolumn dispersion when the full 24 cm available bed length was used and a proportionally larger increase for shorter bed lengths. Thus, the headers are shown to produce a significant increase in the observed plate height.     

Ultrasound-assisted extraction of nitropolycyclic aromatic hydrocarbons from soil prior to gas chromatography-mass detection

Continuous ultrasound-assisted extraction of nitropolycyclic aromatic hydrocarbons from soil prior to their individual separation and determination by gas chromatography (GC) with MS-MS detection is presented here. A multivariate optimisation of the variables affecting the continuous extraction step (namely, probe position, ultrasound radiation amplitude, percentage of duty cycle of ultrasonic exposure, sonication time, total extractant volume, extractant flow rate and temperature of the water-bath in which the extraction cell was placed) was performed. The method was compared with the reference EPA method 3540 using natural contaminated soils. Similar efficiencies were obtained but with a drastic reduction of both the extraction time (10 min versus 24 h) and the extractant volume (less than 10 ml versus 100 ml) by the proposed method. Detection limits of low picogram were obtained, with repeatability and reproducibility between 4.21-5.70 and 5.20-7.23%, respectively.     

Isolation and analysis of polycyclic aromatic hydrocarbons from natural water using accelerated solvent extraction followed by gas chromatography-mass spectrometry

An innovative analytical procedure for the analysis of polycyclic aromatic hydrocarbons (PAHs) from large-volume water samples is presented. It involves sample preparation, sampling and the elution process in an automated continuous procedure involving the ASE technique. Prior to sampling, a XAD-2 resin column is prepared on the basis of a commercial accelerated solvent extraction (ASE) cartridge so that the resin bed is permanently fixed. Then, the XAD column inside the ASE cartridge is cleaned and conditioned. The sampling procedure involves conventional filtration with subsequent isolation of dissolved PAHs on an XAD-2 resin contained in the ASE cartridge. After sampling, the XAD-2 resin content inside the cartridge is eluted by ASE without any further sample preparation and subsequently reused. In order to validate the procedure, the PAHs were isolated from water samples from the Lake Maggiore (North of Italy) using both XAD-2 resin adsorption and hexane liquid-liquid extraction according to the International Standard Methodology ISO 17993. The mean percentages of deviation between concentrations obtained by both methodologies range from 6% for benzo(a)pyrene to 15% for fluoranthene and benzo(b,k)fluoranthene. Compared to the traditional techniques, this procedure offers numerous practical advantages: easy to perform, fast, savings in solvent volume and in time, all steps are fully automated thus avoiding any XAD-2 resin manipulation during and between steps and moreover, low detection limits were provided (0.001 ng l⁻¹ for chrysene, benzo(b,k)fluoranthene, benzo(a)pyrene, dibenz(a,h)anthracene, benzo(g,h,i)perylene and indeno(1,2,3-cd)pyrene, and 0.01 ng l⁻¹ for acenaphthylene and fluoranthene).This procedure was developed in the frame of a project aimed at evaluating the diffuse input of organic contaminants in the Lake Maggiore.     

Solubility prediction of polycyclic aromatic hydrocarbons in non-aqueous solvent mixtures

This study is aimed at evaluating the applicability of the Jouyban–Acree model for predicting the solubility of polycyclic aromatic hydrocarbons (PAHs) in binary and ternary solvent mixtures at different temperatures by employing a large solubility data set. The solubility is predicted in solvent mixtures at different temperatures within an acceptable error range based on the experimental solubility data of PAHs in mono-solvents. The results reveal that the Jouyban–Acree model could be recommended for practical applications in chemical industries.     

Pressurized fluid extraction of polycyclic aromatic hydrocarbons using silanized extraction vessels

We have investigated the extraction efficiency of a pressurized fluid extraction system using an Ottawa sand matrix, soils and a certified reference material (HS-6) spiked with the 16 polycyclic aromatic hydrocarbon (PAHs) associated with method EPA 8100. Acceptable recoveries were achieved for all PAHs using a nominal sand concentration of 2.0 μg.g^-1. However, similar experiments that were conducted at a concentration of 0.20 μg.g^-1 afforded poor recoveries and poor reproducibility for the six-ring PAHs indeno(1,2,3-cd)pyrene, dibenz(a)anthracene, and benzo(ghi)perylene. These were not adequately addressed by the use of indeno(1,2,3-cd)pyrene-d12 and benzo(g,h,i)perylene-d12 surrogates. Silanization of vessels using dichlorodimethylsilane adequately passivates the system but is only required for the high surface area retention frits. Replicate analyses at concentrations of 200 and 20 ng.g^-1 demonstrated that detection limits in the low ppb range (ng.g^-1) are achieved for Ottawa sand, dry soil and soil with moisture contents up to a mass fraction of 30 %. Such performance is consistent with the analytical requirements of the Canadian Sediment Quality Guidelines. Improved analyte recoveries were also observed for the certified reference material HS-6 which were further improved by increasing extraction temperatures from 100 to 150 °C.

Comparative performance of extraction strategies for polycyclic aromatic hydrocarbons in peats

The assessment of historical trends in atmospheric deposition of organic contaminants by using peat samples has been reported on several occasions because these samples represent an almost ideal medium for recording temporal changes in organic contaminant deposition rates. The determination of polycyclic aromatic hydrocarbons (PAHs) in peat samples is complicated due to the high content of organic matter in peat, which affects both extraction efficiency and analytical quality. A rapid and simple method is proposed for the determination of 10 US Environmental Protection Agency indicator PAHs in complex matrices such as peat. This article reviews and addresses the most relevant analytical methods for determining PAHs in peat. We discuss and critically evaluate three different extraction procedures, such as ultrasound-assisted solvent extraction (UASE), shaking and pressurized liquid extraction (PLE). Clean-up of extracts was performed by solid-phase extraction using silica cartridges. Detection of the selected PAHs was carried out by high-performance liquid chromatography coupled with fluorescence detection for determination. Optimization of the variables affecting extraction by the selected extraction techniques was conducted, concluding that the UASE extraction method using hexane:dichloromethane (80:20) as extractant was robust enough to determine the selected PAHs in peat samples with estimated quantification limits between 0.050 and 3.5 μg/kg depending on the PAH. UASE did not demand sophisticated equipment and long extraction times. PLE involved sophisticated equipment and showed important variations in the results. The method proposed was applied to the determination of PAHs in peat samples from Xistral Mountains (Galicia, Spain).