Strain-Controlled Tensile Deformation Behavior and Relaxation Properties of Isotactic Poly(1-butene) and Its Ethylene Copolymers

The tensile deformation behaviour of poly(1-butene) and two of its ethylene copoloymers was studied at room temperature. This was done by investigating true stress-strain curves at constant strain rates, elastic recovery and stress relaxation properties and in-situ WAXS patterns during the deformation process. As for a series of semicrystalline polymers in previous studies, a strain-controlled deformation behaviour was found. The differential compliance, the recovery properties and the stress relaxation curves changed simultaneously at well-defined points. The strains at which these points occurred along the true stress-strain remained constant for the different samples despite their different percentage crystallinities. The well-defined way in which the different samples respond to external stresses complies with the granular substructure of the crystalline lamellae in a semicrystalline polymer.     

Tensile deformation of high strength and high modulus polyethylene fibers

The influence of tensile deformation on gel-spun and hor-drawn ultra-high molecular weight polyethylene fibers has been investigated. In high modulus polyethylene fibers no deformation energy is used to break chemical bonds during deformation, and flow is predominantly present next to elastic behavior. Flow is reversible after tensile deformation to small strains, but becomes irreversible when yielding occurs.Stress relaxation experiments were used to determine the elastic and flow contribution to tensile deformation. A simple quantitative relation could then be derived for the stress-strain curve that directly links yield stress to modulus. Experimental stress-strain curves could be reasonably described by this relation.Flow during tensile deformation is shown to be correlated with the introduction of the hexagonal phase in crystalline domains. A mechanism of flow is proposed in which, at first, tie molecules or intercrystalline bridges are pulled out of crystalline blocks (reversible), followed by the break-up of crystalline blocks through slip of microfibrils past each other (stress-induced melting, irreversible).     

Predicting shape memory characteristics of polyurethane in three‐point bending deformation

As a kind of an exceptional material, the temperature‐responding shape memory polymer can fix a temporary shape when cooled down and recover to its original shape when reheated up. Several models have been developed to describe the process. In the present work, we use the generalized Maxwell model to predict the shape memory characteristics of polyurethane in three‐point bending deformation by means of three‐dimensional finite element simulation. The deformation–temperature–stress behavior is obtained numerically. The results reveal that under the condition of accelerating reheating rates at the stage of stress‐free recovery, the maximum recovery rate occurs at higher temperature whereas the recovery ratio decreases. When the deformation degree enlarges, the maximum recovery stress increases in the situation of constrained recovery. The micro‐motion theory of polymer segments is used to explain the characteristics in the shape memory cycle. The simulated results agree well with previous researches, which demonstrate that the simplified model and the numerical simulation method are helpful for both scientific research and engineering development about shape memory polymers. Copyright © 2014 John Wiley & Sons, Ltd.     

Small-angle X-ray scattering studies of microdomain structure in segmented polyurethane elastomers

The small-angle x-ray scattering (SAXS) technique has been used to characterize the detailed microphase structure of two crosslinked segmented polyurethane elastomers. Both copolymers contain trifunctional polypropylene ether triols in the rubbery elastomeric block, but are synthesized with different hard segments: a symmetric 4,4′-diphenylmethane diisocyanate (MDI) chain extended with butanediol (BD); and an 80/20 mixture of asymmetric 2,4-toluene diisocyanate (TDI) and symmetric 2,6-toluene diisocyanate (TDI) chain extended with ethylene glycol (EG). Calculations of SAXS invariants and determinations of deviations from Porod's law are used to examine the degree of phase segregation of the hard- and soft-segment domains. Results show that the overall degree of phase separation is poorer in the asymmetric TDI/EG-based copolymer than in the symmetric MDI/BD-based copolymer. Determination of diffuse phase boundary thicknesses, however, reveals that the domain boundaries are sharper in the asymmetric TDI/EG system. The contrasting morphologies found in the two systems are interpreted in terms of differences in hard-soft segment compatibility, diisocyanate symmetry, and diisocyanate length. Coupled with conformational considerations, this information is used to construct a new model for polyurethane hard-segment microdomain structure. Important features of the model are that it takes into account the effects of hard-segment sequence length distribution and allows for folding of the longer hard-segment sequences back into the hard-segment domain.     

Preparation of high‐temperature polyurethane by alloying with reactive polyamide

A series of novel poly(urethane amide) films were prepared by the reaction of a polyurethane (PU) prepolymer and a soluble polyamide (PA) containing aliphatic hydroxyl groups in the backbone. The PU prepolymer was prepared by the reaction of polyester polyol and 2,4‐tolylenediisocyanate and then was end‐capped with phenol. Soluble PA was prepared by the reaction of 1‐(m‐aminophenyl)‐2‐(p‐aminophenyl)ethanol and terephthaloyl chloride. The PU prepolymer and PA were blended, and the clear, transparent solutions were cast on glass substrates; this was followed by thermal treatments at various temperatures to produce reactions between the isocyanate group of the PU prepolymer and the hydroxyl group of PA. The opaque poly(urethane amide) films showed various properties, from those of plastics to those of elastomers, depending on the ratio of the PU and PA components. Dynamic mechanical analysis showed two glass‐transition temperatures (T_g's), a lower T_g due to the PU component and a higher T_g due to the PA component, suggesting that the two polymer components were phase‐separated. The rubbery plateau region of the storage modulus for the elastic films was maintained up to about 250 °C, which is considerably higher than for conventional PUs. Tensile measurements of the elastic films of 90/10 PU/PA showed that the elongation was as high as 347%. This indicated that the alloying of PU with PA containing aliphatic hydroxyl groups in the backbone improved the high‐temperature properties of PU and, therefore, enhanced the use temperature of PU. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3497–3503, 2002     

Novel elastomeric polyurethane fibers modified with polypropylene microfibers

Extrusion of immiscible polymer biphasic blends to form in situ microfibers of the minor component in the matrix of the major component is an elegant way to create composites with new properties. The process was used to obtain thermoplastic polyurethane elastomers modified with polypropylene microfibers. The effect of phase interaction on blend morphology and properties was studied by running a series of blends with and without a maleated polypropylene compatibilizer. Six different blends were prepared: three with compatibilizer and three without the compatibilizer. All blends contained polypropylene as a minor component (80/20; 90/10 and 95/5). Extrusion spinning of polyurethane/polypropylene blends with and without compatibilizer resulted in polyurethane fibers modified with highly-oriented polypropylene microfibrils at all component ratios. Increasing polypropylene concentration in the thermoplastic polyurethane matrix increased hardness and modulus, but did not affect tensile strength and lowered elastic recovery.     

Network structure and mechanical properties of allophanate-cured polyurethane rubber

An allophanate-cured polyurethane (PU) has been prepared. The relationship between trifunctional network structure and mechanical properties is discussed. Mooney-Rivlin constants C₁ and C₂ are determined from stress-strain isotherms. C₂ is approximately constant. The average value of structure factor A₃ in the limit at large deformation is 0.432, in fair agreement with the theoretical prediction of 1/3. The structure factor A′₃ of all PU samples becomes roughly unity in the limit at small deformation. The experimental results are interpreted by the recent Flory theory (a fluctuation-constraint model of junctions). The κ parameter decreases with increasing crosslink density; the ξ parameter is small and approaches zero. Increasing crosslink density tends to cause phantom deformation for extended PU networks. However, the absolute value of the reduced stress in the limit at large deformation (or for the equivalent phantom network) [f] is believed to be overestimated for PU networks with high crosslink density. The origin of this behavior is discussed in detail.     

Semi-interpenetrating polymer networks of polyurethane and poly(vinyl chloride)

Summary A series of semi-interpenetrating polymer networks (semi-IPN) of polyurethane (PU) and poly(vinyl chloride) (PVC) has been obtained by prepolymer method and characterised by FTIR; morphological features were examined by SEM-EDS. It has been found that PVC spherical aggregates are dispersed in the PU matrix, but Cl atoms location indicates partial miscibility of both polymers at the interphase which is probably due to hydrogen bonding and/or dipole-dipole interactions. The PVC component influences the phase behaviour of PUs hard segments, as evidenced by DSC results. Thermogravimetric analysis (TG) reveals a complex, multi-step decomposition process with the main mass loss at 503-693 K, while the DTG maxima are located between 540 and 602 K.     

Enhanced thermal and tensile behaviour of MWCNT reinforced palm oil polyol based shape memory polyurethane

Shape memory polyurethane (SMPU) has received tremendous interest because of its low cost, low density, as well as easy processing. However, its inferior mechanical properties compared to shape memory alloys have constrained its application in a broad range of engineering areas. Nanofillers are commonly added to polymers to overcome the problem associated with low mechanical characteristics. This study aims to examine the effect of various loadings of multiwalled carbon nanotubes (MWCNT) on the thermal stability, soft segment crystallinity, tensile and shape memory behaviour of palm oil polyol based SMPU nanocomposites. The SMPU nanocomposites were synthesised using a two-step polymerisation process. Microphase-separated SMPU nanocomposites obtained as the differential scanning calorimetric analysis showed two melting transitions, which belonged to the soft and hard phase domains. Furthermore, it was found that MWCNT had acted as a nucleating agent, which promoted the crystallisation process of SMPU nanocomposites. The thermal stability and tensile properties of SMPU/MWCNT nanocomposites were enhanced significantly as the MWCNT was added to the SMPU matrix. A considerable enhancement in the shape fixity (SF) value was revealed for PU-30 and PU-40 samples with the addition of MWCNT. The shape recovery (SR) time of SMPU was faster for samples reinforced with MWCNT, whereas SF increased while SR decreased upon increasing the shape memory cycle. The SMPU nanocomposites produced demonstrated enhanced thermal and tensile properties, which has the potential as smart material in many industrial applications.     

Morphology and performance of unsaturated polyester nanocomposites modified with organoclay and thermoplastic polyurethane

<正>Unsaturated polyester(UPR)/thermoplastic polyurethane(TPU)/organoclay nanocomposites were prepared by melt compounding of thermoplastic polyurethane and unsaturated polyester prepolymer,and then mixing with the hybrids of styrene monomers and organoclay at ambient temperature.The crosslinking reaction eventually occurred through the unsaturated polyester prepolymer and styrene monomer.The morphology of the composites was investigated by scanning electron microscopy(SEM) and transmission electron microscopy(TEM).The results show that the impact strength of UPR/TPU/organoclay nanocomposites increases obviously;the cure shrinkage decreases markedly,the glass transition temperature is enhanced and an elastic response to the deformation is prominent at the temperature above 10℃.     

Thermal and mechanical characteristics of polyurethane/curaua fiber composites

Polyurethane composites reinforced with curaua fiber at 5, 10 and 20% mass/mass proportions were prepared by using the conventional melt-mixing method. The influence of curaua fibers on the thermal behavior and polymer cohesiveness in polyurethane matrix was evaluated by dynamic mechanical thermal analysis (DMTA) and by differential scanning calorimetry (DSC). This specific interaction between the fibers and the hard segment domain was influenced by the behavior of the storage modulus E′ and the loss modulus E″ curves. The polyurethane PU80 is much stiffer and resistant than the other composites at low temperatures up to 70°C. All samples were thermoplastic and presented a rubbery plateau over a wide temperature range above the glass transition temperature and a thermoplastic flow around 170°C.     

Multifunctional flexible and stretchable polyurethane/carbon nanotube strain sensor for human breath monitoring

Flexible and stretchable polyurethane/carbon nanotube composite with strain detection ability was used for human breath monitoring. The composite material consisted of a network of multiwalled carbon nanotubes and thermoplastic high elastic polyurethane. It was found that elongation of the composite led to a macroscopic increase in electrical resistance, which can be used as a principle for applied strain detection. This detection was reversible, durable, and sensitive with gauge factor reaching very promising value, as, for example, ~46 at applied deformation of 8.7%. Further, the composite could be elongated to very large extend of deformation without discontinuity in measured resistance change reaching gauge factor ~ 450 at composite mechanical break at ~300% of strain. Sensor durability was also confirmed by sine wave deformation cycling when any decrease in the sensor properties for more than 10³ cycles was observed. Simultaneously, the prepared composite possessed other utility properties also and was considered as multifunctional when it was tested as an organic solvent vapor sensor, an element for Joule heating and finally as a microstrip antenna.     

Electrospinning‐induced shape memory effect in thermoplastic polyurethane characterization and thermoviscoelastic modeling

Electrospun thermoplastic polyurethane (TPU) nanofibers are known to contract considerably (～40%) on heating up to ～90 °C. This study investigates this thermomechanical behavior and the TPU shape memory capabilities. The shape memory effect was first studied in TPU films as a model system by applying classical thermomechanical cycles (programming and recovery). The films were able to fix the applied deformation during long‐term storage at room temperature, well above the material's calorimetric glass transition temperature and in the absence of a percolated structure of hard domains. Structural analysis (Fourier transform infrared, differential scanning calorimeter, and dynamic mechanical analysis) revealed broad thermal transitions indicating the presence of a mixed phase of hard segments dispersed in the soft segment matrix. Using a linear viscoelastic model together with time–temperature superposition, the shape memory effect was attributed to the thermoviscoelastic properties of TPU. In particular, the mixed phase was found to give rise to a very broad relaxation spectrum dominated by long relaxation times, which explains the suppression of strain recovery at room temperature. Finally, the electrospinning process was examined and was found to be similar to a programming cycle characterized by the strong elongation flow accompanied by massive solvent evaporation, whereas the contraction effect was interpreted as the recovery phase in a shape memory perspective. Thus, the contraction of electrospun TPU mats may be considered to be an electrospinning‐induced shape memory effect. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1590–1602     

Microbial degradation of polyurethane

The process of decomposition of polyurethane samples in various soils has been studied.     

Characterization of stress‐strain behavior for binary blends of isotactic polypropylene with ethylene‐α‐olefin copolymer

The characterization of the mechanical nonlinear behavior of isotactic polypropylene/ethylene‐1‐hexene copolymer blends with various kinds of morphology was carried out using a nonlinear constitutive equation in which the plastic deformation and the anharmonicity of elastic response are taken into account. It was found that the mechanical nonlinearity of the incompatible blends showing phase separation is much greater than that of the compatible blends having rubbery components in the interlamellar regions. Moreover, the mechanical behavior is governed by the plastic deformation for the incompatible blends, whereas the anharmonicity strongly affects the mechanical behavior for the compatible blends. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1513–1521, 1999     

Orientational order and finite strain in nematic elastomers

Nematic elastomers exhibit large, spontaneous shape changes at the transition from the high-temperature isotropic phase to the low-temperature nematic phase. These finite deformations are studied here in the context of a nonlinear, properly invariant, variational theory that couples the orientational order and elastic deformation. The theory is based on the minimization of a free-energy functional that consists of two contributions: a nematic one due to the interaction of the mesogenic units and an elastic one arising from the stretching of the cross-linked polymer chains. Suitable choices for these two contributions allow for large, reversible, spontaneous shape changes in which the elastic deformation can affect the isotropic-nematic transition temperature. The change in transition temperature as well as the magnitude of the resulting spontaneous deformation is illustrated for various parameter values. The theory includes soft elasticity as a special case but is not restricted to it.     

Synthesis and physicochemical properties of polyurethane block copolymers and their compositions with plasticizers

The synthesis of polyurethane block based on oligoesterdiols 4,4′-methylene-bis(phenylisocyanate), and various chain elongating agents was studied. The properties of these copolymers were compared (using literature data) with selected properties of polyurethanes obtained by the reactions of oligoetherdiols, viz., oligo-3,3′-bis(azidomethyl)oxetanediol and oligo-3-azidomethyl-3′-methyloxetanediol with diisocyanates. The complex of rheological and physicomechanical properties of the initial and plasticized polyurethane block copolymers was studied. Regularities of their deformation behavior were established. The process of mutual solubility was studied by the microinterference method for a wide range of systems block copolymers—plasticizers. On the basis of the data obtained, the phase diagrams were constructed for limitedly compatible systems.     

Structure and deformation recovery of the thermoplastic polyurethane spherulite

We investigated the structure and deformation behavior of the thermoplastic polyurethane (TPU) spherulite by optical microscopy, tensile testing, Hv light scattering, and small angle X‐ray scattering. The TPU spherulite structure obtained by melt crystallization was coarse consisting of bundle‐like structure containing hard segment (HS) lamellar domain in which the HS domains were stacked and the HS chain direction was perpendicular to the longitudinal axis of the HS domain. By stretching, the spherulite was deformed to ellipsoidal one and the stacked HS lamellar domains were tilted in the stretching direction. The deformed spherulite and the tilted HS domain in the spherulite were recovered to the unstretched state by retraction. The recovery of the structure is ascribed to the characteristic spherulite structure consisting of rubbery soft segment matrix physically cross‐linked with the stacked HS domain. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1585–1594     

Miscibility behaviour of blends of a thermoplastic polyester polyurethane with vinyl polymers

A method based on the intrinsic viscosities of transfer has been used to predict miscibility of polymer blends. This method has been applied to study the change in the phase behaviour of a microphase separated polyester polyurethane (PSPU) on blending with polyvinyl chloride (PVC), polyvinyl acetate (PVAc) and a vinyl chloride-vinyl acetate copolymer (VCVAc). The PVC/PSPU blends are found to exhibit complete miscibility over the entire composition range. PVAc/PSPU blends show immiscibility while VCVAc/PSPU blends show partial miscibility. Thermal analysis and scanning electron microscopic studies of the blend films have confirmed the results evaluated on the basis of the viscosity method.