Implications of LDPE Branching and Mw on Thermal and Mechanical Properties of PP/LDPE Blends

Summary: The influences of short chain branching (SCB) and molecular (M_w) weight of low density polyethylene (LDPE) on the solid state properties of polypropylene (PP)-LDPE blends were investigated by mechanical and thermal techniques. DSC analysis of all blends exhibit a double melting peak at all compositions studied thus suggesting that both PP and LDPE crystals exist separately in the solid state. It was found that the SCB and Mw of LDPE influenced the modulus and ultimate tensile strength of the blends. However, elongation at break seems to be independent of the molecular characteristics of the pure homopolymer especially at PP blend composition greater than 50%. LDPE with high SCB showed broader melting peaks. Addition of a small amount of a low Mw LDPE (10%) resulted in a higher elongation at break than a high Mw LDPE. There is likely a correlation between the presence of a new peak in the thermograms of PP-rich blends and the observed poor elongation at break.     

Effect of oil and cured agent content on the structure and properties of thermoplastic vulcanizates

The effect of oil and curing agent content on the mechanical behavior of thermoplastic vulcanizates, based on a polypropylene (PP) and ethylene‐propylene‐diene copolymer (EPDM), was investigated. Mechanical properties such as Young's modulus, stress at 100% elongation and ultimate stress were investigated as a function of blends' composition and phase morphology. Experimental studies show that the Young's modulus of the vulcanizates depends on both PP/EPDM ratio and oil content in the blends; both ultimate strength and stress at 100% elongation increase with curing agent content.     

The compatibilizing effect of epoxy resin (EP) on polypropylene (PP)/recycled acrylonitrile butadiene rubber (NBRr) blends

A new method was used to prepare thermoplastic elastomers based on polypropylene (PP)/recycled acrylonitrile butadiene rubber (NBRr) with improved mechanical properties. An epoxy resin (EP) was used as a compatibilizing agent. The effect of EP on mechanical properties, swelling percentage and morphological characteristics of the blends was investigated with different blend compositions. The results showed that the incorporation of EP has improved the tensile strength, Young's modulus and elongation at break of PP/NBRr-EP blends compared with PP/NBRr blends. The enhancement of tensile properties of PP/NBRr-EP blends is due to the better adhesion between the two phases with the incorporation of EP. This is quite evident by scanning electron microscopy of tensile fractured surfaces. PP/NBRr-EP blend exhibits lower stabilization torque and swelling percentage than PP/NBRr blends. The lower stabilization torque is an indication of better processing characteristics.     

Alteration of Bacterial Cellulose Properties by Diacetylglycerol

Bacterial cellulose (BC) was altered by means of 0.5-2.5% w/v diacetylglycerol in acetone-water through impregnation process provided DGBC composites. Results from the scanning electron microscope images, revealed that diacetylglycerol filled the pores of BC, leads to the significant enhanced in hydrophilicity and caused a smoother BC morphology. The addition of diacetylglycerol into BC caused a slightly changed in crystallinity indexes and bring about the reduction in tensile strength and Young's modulus but increased in elongation at break and toughness. The significant reduction of tensile strength and Young's modulus was achieved for DGBC 2.5% as well as for elongation at break and hydrophylicity improvement. Through the impregnation method, diacetylglycerol serves as biodegrada–ble and safe plasticizer, resulted in less rigid and higher ductility DGBC composites.     

动态固化聚丙烯/环氧树脂共混物的研究

将动态硫化技术应用于热塑性树脂 热固性树脂体系 ,制备了动态固化聚丙烯 (PP) 环氧树脂共混物 .研究了动态固化PP 环氧树脂共混物中两组分的相容性、力学性能、热性能和动态力学性能 .实验结果表明 ,马来酸酐接枝的聚丙烯 (PP g MAH)作为PP和环氧树脂体系的增容剂 ,使分散相环氧树脂颗粒变细 ,增加了两组分的界面作用力 ,改善了共混物的力学性能 .与PP相比 ,动态固化PP 环氧树脂共混物具有较高的强度和模量 ,含 5 %环氧树脂的共混物拉伸强度和弯曲模量分别提高了 30 %和 5 0 % ,冲击强度增加了 15 % ,但断裂伸长率却明显降低 .继续增加环氧树脂的含量 ,共混物的拉伸强度和弯曲模量增加缓慢 ,冲击强度无明显变化 ,断裂伸长率进一步降低 .动态力学性能分析 (DMTA)表明动态固化PP 环氧树脂共混物是两相结构 ,具有较高的储能模量 (E′)     

Tailoring of interface of polypropylene/polystyrene/carbon nanofibre composites by polystyrene-block-poly(ethylene-ran-butylene)-block-polystyrene

Mechanical and physical properties of polypropylene (PP)/polystyrene (PS) blend, PP/PS/polystyrene-block-poly(ethylene-ran-butylene)-block-polystyrene (SEBS) ternary blend and their composites with carbon nanofibers (CNF) were investigated. Composites of ternary blend exhibited superior properties compared to those of binary blends. Mechanical performance of nanocomposites was intimately related to their phase morphology. PP/PS/SEBS/0.1 wt% CNF hybrid composites exhibited excellent impact strength (Four-fold increase compared to PP/PS blend) and ductility (12-fold increase in elongation at break, with respect to PP/PS blend). Moreover, these composites displayed good tensile strength and modulus (15% increase in Young's modulus, compared to PP/PS/SEBS blend) and are suitable for various end-use applications including automobile applications. Although crystallinity of PP phase is decreased by the incorporation of CNF, thermal stability of the composites remained almost unaffected. Contact angle measurements revealed that ternary composites exhibited maximum hydrophobicity.     

Mechanical properties and thermal analysis of low‐density polyethylene + polypropylene blends with dialkyl peroxide

Polypropylene + low density polyethylene (PP + LDPE) blends involving 0, 25, 50, 75 and 100 wt% of PP with dialkyl peroxide (DAP) were prepared by melt blending in a single‐screw extruder. The effects of adding dialkyl peroxide on mechanical and thermal properties of PP + LDPE blends have been studied. It was found that at lower concentrations of peroxide (e.g., 0–0.08 wt% of dialkyl peroxide) LDPE component is cross‐linked and Polypropylene (PP) is degraded in all compositions of PP + LDPE blends. Mechanical properties (Tensile strength at break, at yield and elongation at break), Melt flow index (MFI), hardness, Scanning Electron Microscope (SEM) and thermal analyses (DSC) of these blends were examined. Because of serious degradation or cross‐linking the mechanical properties and the crystallinty (%) of those products were decreased as a result of increasing peroxide content. Copyright © 2009 John Wiley & Sons, Ltd.     

POE改性高熔指聚丙烯性能研究

采用聚烯烃弹性体(POE)对高熔指聚丙烯(PP)进行共混改性,研究了弹性体POE的含量对高熔指PP的力学性能、流动性和成型收缩率的影响规律。结果表明:随着弹性体POE含量的增加,共混材料的悬臂梁缺口冲击强度增大,断裂拉伸应变增大,弯曲强度、弯曲模量降低,拉伸强度降低,流动性变差,收缩率减小。     

Solid-state morphology,structure, and tensile properties of polyethylene/polyamide/nanoclay blends: Effect of clay fraction

The effect of nanoclay fraction on the linear and non-linear tensile properties of a polyethylene/polyamide 12 blend with droplet morphology was investigated. All ternary blends were prepared at a fixed polyamide (PA) weight fraction of 20%, and at clay volume fractions varying from 0.5 to 2.5% relative to PA. Scanning electron microscopy and transmission electron microscopy were used to characterize the morphology of the blends and the clay interphase structure. The nanoclay content was shown to strongly influence both linear and non-linear tensile properties. Young's modulus, elongation at yield, yield strength, tensile strength and elongation at break as a function of clay fraction were studied and discussed in terms of morphological changes and strain-induced structural reorganization of the clay interphase.     

Tensile and flexural properties of polypropylene composites filled with highly effective flame retardant magnesium hydroxide

The reinforcing effects of highly effective flame retardant magnesium hydroxide (FMX) content on the tensile and flexural properties of filled polypropylene (PP) composites were investigated within the FMX weight fraction range from 5 to 60 wt%. It was found that the Young's modulus and flexural modulus increased approximately linearly while the tensile yield strength and tensile fracture strength decreased slightly with increasing the FMX weight fraction. When the FMX weight fraction was lower than 20%, the tensile elongation at break decreased considerably, and then decreased slightly; the flexural strength increased when the FMX weight fraction was lower than 30%, and then decreased slightly. The tensile properties increased with increasing rate of tension. Moreover, the tensile yield strength of the composites was estimated using an equation proposed in previous work, and good agreement was shown between the predicted and the measured data.     

Preparation and cryogenic mechanical properties of epoxy resins modified by poly(ethersulfone)

A thermoplastic, poly(ethersulfone) (PES) was used to modify a bisphenol‐F based epoxy resin cured with an aromatic diamine. The initial mixtures before curing, prepared by melt mixing, were homogeneous. Scanning electron microscopy (SEM) micrographs of solvent‐etched fracture surfaces of the cured blends indicated that phase separation occurred after curing. The cryogenic mechanical behaviors of the epoxy resins were studied in terms of tensile properties and Charpy impact strength at cryogenic temperature (77 K) and compared to their corresponding behaviors at room temperature (RT). The addition of PES generally improved the tensile strength, elongation at break, and impact strength at both RT and 77 K except the RT tensile strength at 25 phr PES content. It was interesting to observe that and the maximum values of the tensile strength, elongation at break, and impact strength occurred at 20 phr PES content where a co‐continuous phase formed. Young's modulus decreased slightly with the increase of the PES content. Moreover, the tensile strength and Young's modulus at 77 K were higher than those at RT at the same composition, whereas the elongation at break and impact strength showed the opposite results. Finally, the differential scanning calorimetry analysis showed that the glass transition temperature (T_g) was enhanced by the addition of PES. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 612–624, 2008     

Evaluation of the SEBS copolymer in the compatibility of PP/ABS blends through mechanical,thermal, thermomechanical properties,and morphology

Polypropylene (PP) blends with acrylonitrile-butadiene-styrene (ABS) were prepared using the styrene-ethylene-butylene-styrene copolymer (SEBS) as a compatibilizing agent. The blends were prepared in a co-rotational twin-screw extruder and injection molded. Torque rheometry, Izod impact strength, tensile strength, heat deflection temperature (HDT), differential scanning calorimetry, thermogravimetry, and scanning electron microscopy properties were investigated. The results showed that there was an increase in the torque of PA6/ABS blends with SEBS addition. The PP/ABS/SEBS (60/25/15%) blend showed significant improvement in impact strength, elongation at break, thermal stability, and HDT compared with neat PP. The elastic modulus and tensile strength have not been significantly reduced. The degree of crystallinity and the crystalline melting temperature increased, indicating a nucleating effect of ABS. The PP/ABS blends compatibilized with 12.5% and 15% SEBS presented morphology with well-distributed fine ABS particles with good interfacial adhesion. As a result, thermal stability has been improved over pure PP and the mechanical properties have been increased, especially impact strength. In general, the addition of the SEBS copolymer as the PP/ABS blend compatibilizer has the advantage of refining the blend's morphology, increasing its toughness and thermal stability, without jeopardizing other PP properties.     

Mechanical properties and morphology for polypropylene composites filled with microencapsulated red phosphorus

The effects of the microencapsulated red phosphorus (MRP) content and specimen thickness on the mechanical properties of the filled polypropylene (PP) composites were studied at room temperature. The results showed that the influence of the MRP on the tensile and impact properties of the composites was significant, and the Young's modulus and impact strength of the composites increased nonlinearly while the tensile strength decreased slightly with increasing the MRP weight fraction; the tensile elongation at break increased outstandingly when the MRP weight fraction was less than 2% and then decreased with increasing the MRP weight fraction. Furthermore, the impact fracture surface was examined by scanning electronic microscope. The results suggested that the toughening effect was attributed to the absorption of impact fracture energy by the microencapsulated layer. Copyright © 2014 John Wiley & Sons, Ltd.     

Study and characterization of virgin and recycled LDPE/PP blends

Recycling of mixed plastic wastes composed of low-density polyethylene (LDPE) matrix and polypropylene (PP) was carried out by compounding using single-screw or twin-screw extruders. Blends of virgin polymers have been prepared to compare mechanical properties of both virgin and regenerated materials. First, a model composition of virgin LDPE/PP blend was prepared to study the effect of process parameters and that of different types of compatibilizers. Second, the results were applied to plastic wastes coming from industrial post-consumer plastic wastes. By adding compatibilizing agents such as ethylene-propylene-diene monomer, ethylene-propylene monomer, or PE-g-(2-methyl-1,3-butadiene) graft copolymer, elongation at break and impact strength were improved for all blends. The effect of these various copolymers is quite different and is in relation with their chemical structure. The recycled blends exhibit suitable properties leading to applications that require good mechanical properties.     

Polymer blends—I. Mechanical and morphological behaviour of polyethylene/polyvinyl chloride blends

As part of a fundamental study of the behaviour of mixed plastics during reprocessing and in service, blends of low density polyethylene (LDPE) and polyvinyl chloride (PVC) have been investigated. It was found that Young's modulus increased steadily from pure LDPE to pure PVC whereas both tensile strength at break and elongation at break passed through a minimum at about 5% PVC. Optical and scanning electron microscope studies have related this mechanical behaviour to morphological changes in the two phase system under stress.     

COMPATIBILIZERS FOR LOW DENSITY POLYETHYLENE/POLYPROPYLENE BLENDS

The role of polyolefin elastomers as compatibilizers in Low Density Polyethylene/Polypropylene (LDPE/PP) blends, in the presence of di-cumyl peroxide (DCP) has been studied. Mixtures of 90/10 LDPE/PP ratio, were prepared in a Brabender plasticorder and tested for their mechanical properties and calorimetric response. Then the elastomers ethylene-propylene-diene copolymer (EPDM) and polybutadiene (BR) were added, alone or together with 0.2% DCP at concentrations up to 2%. The mixing torque and gel content of the above products were recorded as a function of the blend consistency. Also, the mechanical properties of specimens were measured as an additional evidence to explore the capabilities of these additives to promote compatibility of the blend components. It was found that EPDM and BR can be easily incorporated into polyolefin blends and appear suitable as potential compatibilizers for those materials, probably acting within the PP phase. Both elastomers result in an increase of strength and modulus, the BR having more enhanced effect. The latter gives low elongation, which allows its use in applications where high tensile properties are desired and flexural behavior is not critical.     

Analysis of thermomechanical reprocessing effects on polypropylene/ethylene octene copolymer blends

The impact of recycling by grinding and re-extrusion on the physical and mechanical properties of polypropylene (PP)/ethylene octene copolymer (EOC) blends was investigated. The considered EOC content was 0 wt. %, 10 wt. % and 20 wt. %, and the investigated number of recycling passes (extrusions) was 0, 1, 3 and 6. Up to 6 re-extrusions, an increase of the melt flow index (MFI), a slight increase of the crystallinity, a slight decrease of the decomposition temperature (T_onset), and no significant oxidation were noted. Therefore, the recycling of the blends induces thermomechanical degradation by chain scission without oxidation. Increasing the content of EOC increases the MFI and the T_onset of the PP blends. The first recycling procedure induced an increase of the Young's modulus and tensile yield stress, while for higher recycling numbers, these two parameters dropped. The EOC inclusions stabilized the tensile elongation at break up to 3 recycling procedures due to a decrease of their size and a homogenization of their shape, while that of neat PP continuously decreased with recycling numbers.     

ENR-25改性CaCO3填充LDPE的复合材料的研究

用环氧程度为25％的环氧化天然橡胶（ENR－25）改性轻质CaCO3。研究了改性方法，改性剂用量，CaCO3填充量对低密度聚乙烯（LDPE）材料与性能的影响。结果表明，7．5％的ENR－25湿法改性有效地改善了CaCO2在LDPE中的分散性及相容性，增强了界面作用强度，使材料在拉伸强度保持较高的情况下，拉伸弹性模量，撕裂强度和断裂伸长率得到有效的提高。     

Crosslinked polyolefins as matrices for two-phase materials

This paper gives a review of the results of investigation of the effect of crosslinking on the properties of LDPE/PP^a) blends and LDPE filled with particulate silica. Tensile and impact properties, crystallization behaviour, crosslinked portion formation and crack growth rate have been investigated. Crosslinking results in an increased compatibility of originally incompatible LDPE/PP blends apparently due to an in situ formation of a compatibilizer, leading to improved deformability and better impact resistance. Changes in the morphology as revealed by crystallization behaviour, and the increased number of tie molecules in amorphous region due to crosslinking result in better impact resistance of LDPE/silica mixtures, as well as to the improvement of other properties of two-phase materials, so as resistance to grack growth.     

Effect of surface modification of colloidal silica nanoparticles on the rigid amorphous fraction and mechanical properties of amorphous polyurethane–urea–silica nanocomposites

Colloidal silica nanoparticles (NPs) modified with eight different silane coupling agents were incorporated into an amorphous poly(tetramethylene oxide)‐based polyurethane–urea copolymer matrix at a concentration of 10 wt % (4.4 vol %) in order to investigate the effect of their surface chemistry on the structure–property behavior of the resulting nanocomposites. The rigid amorphous fraction (RAF) of the nanocomposite matrix as determined by differential scanning calorimetry and dynamic mechanical analysis was confirmed to vary significantly with the surface chemistry of the NPs and to be strongly correlated with the bulk mechanical properties in simple tension. Hence, nanocomposites with an RAF of about 30 wt % showed a 120% increase in Young's modulus, a 25% increase in tensile strength, a 15% decrease in elongation at break with respect to the neat matrix, which had no detectable RAF, whereas nanocomposites with an RAF of less than 5% showed a 60% increase in Young's modulus, a 10% increase in tensile strength and a 5% decrease in the elongation at break. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2543–2556