TLCP/PEI共混体系的流变特性与结构关系的研究

研究了VectraA950/PEI共混体系多层次结构与共混体系动态流变特性的关系.在研究液晶高分子的动态流变特性时,引入Palierne模型对动态实验结果进行预测.结果表明,TLCP分散相在高频时偏离了球形,导致Palierne模型拟合的结果与TLCP/PEI共混体系的实验结果在高频时不吻合.这与VectraA950/PEI共混体系中多层次结构在动态流场中的流变响应有关:在频率偏高时,液晶高分子取向不能完全松弛,易于形成各向异性结构,在流场作用下,易产生大形变;由于液晶高分子液滴的回缩过程很慢,在频率偏高时,产生的大形变不易回复,所以保留了纤维结构.     

The effect of various compatibilizers on thermal,mechanical, and morphological properties of polystyrene/polypropylene blends

The effects of various compatibilizers on thermal, mechanical and morphological properties of 50/50 polypropylene/polystyrene blends were investigated. Various compatibilizers, polystyrene-(ethylene/butylenes/ styrene) (SEBS), ethylene vinyl acetate (EVA), polystyrene-butylene rubber (SBR) and blend of compatibilizers SEBS/PP-g-MAH, EVA/PP-g-MAH, and SBR/PP-g-MAH were used. Differential scanning calorimetry, thermogravimetric analysis, wide-angle X-ray scattering, scanning electron microscopy, microhardness, and Izod impact strength were adopted. It was found that the influence of various compatibilizers was appeared on all the properties studied. The properties of the blends compatibilized with SEBS, EVA, and SBR are very distinct from those of blends compatibilized with blend of compatibilizers. Results show that compatibilized blends with the blend of compatibilizers EVA/PP-g-MAH, SBR/PP-g-MAH, and SEBS/PP-g-MAH or SBR were relatively more stable than the uncompatibilized blend and blend compatibilized with SEBS or EVA. The compatibilizer does not only reduce the interfacial tension or increase the phase interfacial adhesion between the immiscible polymers, but greatly affects the degree of crystallinity of blends.

     

离聚物对含液晶聚合物聚砜体系的增容作用

离聚物对含液晶聚合物聚砜体系的增容作用刘杰，何嘉松（中国科学院化学研究所工程塑料国家重点实验室北京１０００８０）关键词增容作用，离子聚合物，热致液晶聚合物，高分子共混物，原位复合材料工程塑料与液晶聚合物（Ｌｒｙ）共混（形成所谓的原位复合材料）时在降低...     

Polymer blends of sPS/PA6 compatibilized by sulfonated syndiotactic polystyrene

Syndiotactic polystyrene (sPS) and polyamide-6 (PA6) are immiscible and incompatible and have been recognized. In this study, sulfonated syndiotactic polystyrene (SsPS-H) is employed as compatibilizer in the blend of sPS/PA6. During melt blending, the sulfonic acid groups of the SsPS-H can interact strongly with the amine end-groups of PA6 through acid-base interaction. In addition, SsPS-H is miscible with sPS when SsPS-H content is less than 20 wt.%. Therefore, the addition of SsPS-H to sPS/PA6 blends reduces the dispersed phase size and improves the adhesion between the phases. The glass transition temperatures of the PA6 component in the compatibilized blends shift progressively towards higher temperature with the content of SsPS-H-12 increase, indicating enhanced compatibility. On the other hand, the progressive lowering of the melting point and crystallization temperatures of PA6 in the blends with increasing SsPS-H contents compared to the incompatibilized blend, provide some insight into the level of interaction between the PA6 and SsPS-H. The compatibilized blends have significantly higher impact strength than the blends without SsPS-H. The best improvement in the impact strength of the blends was achieved with the content of the SsPS-H (11.9 mol%) about 5 wt.%.     

Reactively and physically compatibilized immiscible polymer blends: stability of the copolymer at the interface

This paper reports on the interfacial behaviour of block and graft copolymers used as compatibilizers in immiscible polymer blends. A limited residence time of the copolymer at the interface has been shown in both reactive blending and blend compatibilization by preformed copolymers. Polystyrene (PS)/polyamide6 (PA6), polyphenylene oxide (PPO)/PA6 and polymethylmethacrylate (PMMA)/PA6 blends have been reactively compatibilized by a styrene-maleic anhydride copolymer SMA. The extent of miscibility of SMA with PS, PPO and PMMA is a key criterion for the stability of the graft copolymer at the interface. For the first 10 to 15 minutes of mixing, the in situ formed copolymer is able to decrease the particle size of the dispersed phase and to prevent it from coalescencing. However, upon increasing mixing time, the copolymer leaves the interface which results in phase coalescence. In PS/LDPE blends compatibilized by preformed PS/hydrogenated polybutadiene (hPB) block copolymers, a tapered diblock stabilizes efficiently a co-continuous two-phase morphology, in contrast to a triblock copolymer that was unable to prevent phase coarsening during annealing at 180°C for 150 minutes.     

Correlation of the minor-phase orientation to the flow-induced morphological transitions in thermotropic liquid crystalline polymer/PBT blends

Immiscible blends of thermotropic liquid crystalline polymers (TLCP) and a flexible polymer matrix show viscosity reductions and extensive fiber formation under certain flow conditions. Here we study these phenomena by directly examining the TLCP component's molecular orientation and the dispersed phase morphology. The rheology and morphology of blends of polybutylene terephthalate and a thermotropic copolyester (HX-8000 series, DuPont) at concentrations varying from 5 to 30 wt % of TLCP are characterized. It is found that the blends show viscosity reduction as well as stable fiber formation at shear rates dependent on the TLCP content. Wide-angle X-ray scattering is performed to measure the degree of molecular orientation of the TLCP phase. A deconvolution scheme isolates the scattering from the TLCP in the blends and a molecular model enables extracting an experimental orientation factor. It was found that a highly microfibrillated TLCP phase is coupled with an increase in the TLCP molecular orientation to values close to the pure TLCP at similar processing conditions. Further, the microfibrillated TLCP phase is found to be stable within the testing time. Current hypotheses about fiber formation in immiscible blends are tested against the experimental observations. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1769–1780, 1998     

Morphology and properties of isotactic polypropylene/poly(ethylene terephthalate) in situ microfibrillar reinforced blends: Influence of viscosity ratio

In situ microfibrillar reinforced blends based on blends of isotactic polypropylene (iPP) and poly(ethylene terephthalate) (PET) were successfully prepared by a “slit extrusion-hot stretching-quenching” process. Four types of iPP with different apparent viscosity were utilized to investigate the effect of viscosity ratio on the morphology and mechanical properties of PET/iPP microfibrillar blend. The morphological observation shows that the viscosity ratio is closely associated to the size of dispersed phase droplets in the original blends, and accordingly greatly affects the microfibrillation of PET. Lower viscosity ratio is favorable to formation of smaller and more uniform dispersed phase particles, thus leading to finer microfibrils with narrower diameter distribution. Addition of a compatibilizer, poly propylene-grafted-glycidyl methacrylate (PP-g-GMA), can increase the viscosity ratio and decrease the interfacial tension between PET and iPP, which tends to decrease the size of PET phase in the unstretched blends. After stretched, the aspect ratio of PET microfibrils in the compatibilized blends is considerably reduced compared to the uncompatibilized ones. The lower viscosity ratio brought out higher mechanical properties of the microfibrillar blends. Compared to the uncompatibilized microfibrillar blends, the tensile, flexural strength and impact toughness of the compatibilized ones are all improved.     

Effects of poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] on the charge distributions of low‐density polyethylene/polystyrene blends

The effect of the triblock copolymer poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) on the formation of the space charge of immiscible low‐density polyethylene (LDPE)/polystyrene (PS) blends was investigated. Blends of 70/30 (wt %) LDPE/PS were prepared through melt blending in an internal mixer at a blend temperature of 220 °C. The amount of charge that accumulated in the 70% LDPE/30% PS blends decreased when the SEBS content increased up to 10 wt %. For compatibilized and uncompatibilized blends, no significant change in the degree of crystallinity of LDPE in the blends was observed, and so the effect of crystallization on the space charge distribution could be excluded. Morphological observations showed that the addition of SEBS resulted in a domain size reduction of the dispersed PS phase and better interfacial adhesion between the LDPE and PS phases. The location of SEBS at a domain interface enabled charges to migrate from one phase to the other via the domain interface and, therefore, resulted in a significant decrease in the amount of space charge for the LDPE/PS blends with SEBS. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2813–2820, 2004     

新型sPS/PA6/SsPS-H塑料合金的性能和形态结构

研究新型sPS PA6 SsPS H塑料合金的力学性能和微观形态结构 .间规聚苯乙烯 (sPS)的磺化产物磺化间规聚苯乙烯 (SsPS H)的加入明显地改善了sPS PA6(聚酰胺 6)二组分合金的力学性能 ,在sPS PA6 SsPS H重量组成为 80 2 0 5时 ,三组分合金的冲击强度最大 ,为 1 5 6kJ m2 ,约为纯sPS冲击强度的 3倍 DMA和SEM结果表明 ,SsPS H对sPS和PA6共混有良好的增容作用 ,它起到了降低合金的微相尺寸和加强相间界面粘结的作用 .此外 ,FTIR结果还表明SsPS H和PA6之间存在特殊相互作用 ,其作用方式是通过SsPS H的磺酸基将其质子转移给PA6酰胺基的氮     

Stress–strain behavior of low‐density polyethylene/poly(methyl methacrylate) blends with modulated interfaces with a hydrogenated polybutadiene‐block‐poly(methyl methacrylate) diblock copolymer

The stress–strain diagrams and ultimate tensile properties of uncompatibilized and compatibilized hydrogenated polybutadiene‐block‐poly(methyl methacrylate) (HPB‐b‐PMMA) blends with 20 wt % poly(methyl methacrylate) (PMMA) droplets dispersed in a low‐density polyethylene (LDPE) matrix were studied. The HPB‐b‐PMMA pure diblock copolymer was prepared via controlled living anionic polymerization. Four copolymers, in terms of the molecular weights of the hydrogenated polybutadiene (HPB) and PMMA sequences (22,000–12,000, 63,300–31,700, 49,500–53,500, and 27,700–67,800), were used. We demonstrated with the stress–strain diagrams, in combination with scanning electron microscopy observations of deformed specimens, that the interfacial adhesion had a predominant role in determining the mechanism and extent of blend deformation. The debonding of PMMA particles from the LDPE matrix was clearly observed in the compatibilized blends in which the copolymer was not efficiently located at the interface. The best HPB‐b‐PMMA copolymer, resulting in the maximum improvement of the tensile properties of the compatibilized blend, had a PMMA sequence that was approximately half that of the HPB block. Because of the much higher interactions encountered in the PMMA phase in comparison with those in HPB (LDPE), a shorter sequence of PMMA (with respect to HPB but longer than the critical molecular weight for entanglement) was sufficient to favor a quantitative location of the copolymer at the LDPE/PMMA interface. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 22–34, 2005     

Morphology of PC/SAN blends: effect of reactive compatibilization,SAN concentration,processing, and viscosity ratio

This article examines the effects of dispersed phase concentration, processing apparatus, viscosity ratio, and interfacial compatibilization using an SAN–amine compatibilizer on the morphology of blends of bisphenol A–polycarbonate (PC) with styrene–acrylonitrile (SAN) copolymers. For uncompatibilized blends, the dispersed phase particle size increased significantly with SAN concentration, and was found to exhibit a minimum at a viscosity ratio of approximately 0.35 for a fixed concentration of 30% SAN in the blend. Although the morphology of uncompatibilized PC/SAN blends mixed in a Brabender mixer, single‐ and twin‐screw extruders were quite similar, the twin‐screw extruder produced significantly finer morphologies in blends containing SAN–amine. The average particle size for blends compatibilized with the SAN–amine polymer was approximately half that of uncompatibilized blends and was relatively independent of viscosity ratio and dispersed phase composition. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 71–82, 1999     

Fractionated crystallization of compatibilized LDPE/PA6 blends

The paper presents differential scanning calorimetry and electron microscopy of the fractionated crystallization and polydispersity of the dispersed PA6 phase in compatibilized LDPE/PA6 75/25 w/w blends. The compatibilizers used were (i) an acrylic acid functionalized polyethylene, Escor 5001 (EAA); (ii) an ethylene-glycidylmethacrylate copolymer, Lotader GMA AX8840 (EGMA); (iii) a polystyrene-poly(ethylene-butylene)-polystyrene triblock copolymer comprising 2 wt.% maleic anhydride grafts, Kraton FG 1901X (SEBS-g-MA). The compatibilizer SEBS-g-MA has the strongest reduction effect upon the size of PA-6 droplets. Its implementation provides the best fractionated crystallization. The fractionated crystallization has not been observed for the blend compatibilized with EGMA. The results show that the degree of compatibilization could be evaluated qualitatively by the progress of the fractionated crystallization. So, the three compatibilizers could be rated according to their effectiveness as follows: SEBS-g-MA > EAA > EGMA. The self-nucleation experiments have demonstrated that the lack of active nuclei in the finely dispersed PA6 droplets is the determining factor for the fractionated crystallization at high supercooling, and not the considered absolute particle size. The measurement of the Vickers microhardness of the compatibilized blends confirms that the compatibilizing activity of SEBS-g-MA and EAA is stronger than that of EGMA.     

SiO2纳米粒子对受限流场下聚异丁烯/聚二甲基硅氧烷共混物相形态的影响

利用显微-光学剪切联用系统构造受限剪切环境,探讨了少量不同表面性质的SiO2纳米粒子的加入对聚异丁烯(PIB)/聚二甲基硅氧烷(PDMS)不相容共混体系分散相形态演变过程的影响.研究结果表明,少量疏水性SiO2纳米粒子的加入可抑制分散相液滴的凝聚,从而抑制珍珠链状及纤维状等超级相形态的形成,使共混物表现为近似本体流体的...     

Highly toughened poly(lactic acid) (PLA) prepared through melt blending with ethylene-co-vinyl acetate (EVA) copolymer and simultaneous addition of hydrophilic silica nanoparticles and block copolymer compatibilizer

In this study, a highly toughened PLA was prepared through physical melt-blending with EVA at the presence of hydrophilic nanosilica and SEBS-g-MA block copolymer compatibilizer. The effect of nanosilica and compatibilizer on the morphology, mechanical properties, and linear rheology of the PLA/EVA blends was also investigated. According to TEM images, nanosilica was selectively located in the PLA matrix while some were placed on the interface between the two polymers as was also predicted by thermodynamic and kinetic analysis. Upon the addition of nanoparticles, the interfacial adhesion between the phases was enhanced and the average droplet size decreased. Interestingly, incorporation of SEBS-g-MA induced morphological changes as the spherical EVA droplets turned into a cylindrical shape. DSC results indicated that blending with EVA copolymer resulted in the reduction of crystallization of PLA matrix; however, the crystallinity increased at the presence of nanoparticles up to 5 wt%. The addition of compatibilizer considerably hindered the crystallization of the PLA phase. PLA/EVA blend containing optimum levels of nanosilica exhibited considerably enhanced tensile toughness, elongation at break, and impact strength. On the other hand, the simultaneous addition of nanoparticles and SEBS-g-MA led to synergistic toughening effects and the compatibilized blend containing nanosilica exhibited excellent impact toughness. For instance, the elongation at break of the compatibilized PLA/EVA blend containing the optimal content of nanosilica was increased from 7% to 121% (compared to neat sample). The notched Izod impact strength was also increased from 5.1 to 65 kJ/m². Finally, the microstructure of the blends was assessed by rheological measurements.     

Influence of microstructure and deformation behavior on toughening of reactively compatibilized polyamide 6 and poly(ethylene-co-butyl acrylate) blends

Influence of microstructure on impact toughness and fracture behavior of PA6 and EBA blends reactively compatibilized by EBA-g-MAH was quantitatively studied. The reactively compatibilized blends showed better distribution of elastomeric EBA particles in the PA6 matrix and the presence of EBA-g-MAH resulted in considerable reduction of interfacial tension between the component polymers. The interfacial adhesion between the PA6 and EBA phase in the compatibilized blends was enhanced by the interfacial reaction between the amide end-groups of PA6 and maleic anhydride group of EBA-g-MAH compared to uncompatibilized blends. The matrix ligament thickness and particle diameter values were lower than the predicted critical values and were responsible for the ductile behavior of the compatibilized blends. Stress whitening around the notch occurred in all the compatibilized blends which was the major energy dissipation zone in the blends. Matrix shear yielding or plastic flow without crazing was the dominant deformation mechanism in the tough compatibilized blends. There was no sign of shear yielding during impact fracture of the uncompatibilized blends where the elastomeric particles were completely dislodged from the matrix.     

Studies on droplet size distributions during coalescence in immiscible polymer blends filled with silica nanoparticles

The effect of silica nanoparticles on the morphology of （10/90 wt%） PDMS/PBD blends during the shear induced coalescence of droplets of the minor phase at low shear rate was investigated systematically in situ by using an optical shear technique. Two blending procedures were used： silica nanoparticles were introduced to the blends by pre-blending silica particles first in PDMS dispersed phase （procedure 1） or in PBD matrix phase （procedure 2）. Bimodal or unimodal droplet size distributions were observed for the filled blends during coalescence, which depend not so much on the surface characteristics of silica but mainly on blending procedure. For pure （10/90 wt%） PDMS/PBD blend, the droplet size distribution exhibits bimodality during the early coalescence. When silica nanoparticles （hydrophobic and hydrophilic） were added to the blends with procedure l, bimodal droplet size distributions disappear and unimodal droplet size distributions can be maintained during coalescence; the shape of the different peaks is invariably Gaussian. Simultaneously, coalescence of the PDMS droplets was suppressed efficiently by the silica nanoparticles. It was proposed that with this blending procedure the nanoparticles should be mainly kinetically trapped at the interface or in the PDMS dispersed phase, which provides an efficient steric barrier against coalescence of the PDMS dispersed phase. However, bimodal droplet size distributions in the early stage of coalescence still occur when incorporating silica nanoparticles into the blends with procedure 2, and then coalescence of the PDMS droplets cannot be suppressed efficiently by the silica nanoparticles. It was proposed that with this blending protocol the nanoparticles should be mainly located in the PBD matrix phase, which leads to an inefficient steric barrier against coalescence of the PDMS dispersed phase; thus the morphology evolution in these filled blends is similar to that in pure blend and bimodal droplet size distributions can be observed during the early coalescence. These results imply that exploiting non-equilibrium processes by varying preparation protocol may provide an elegant route to regulate the temporal morphology of the filled blends during coalescence.     

A rheological and morphological study of a copolyester liquid crystal/polypropylene blend system

The effects of composition and shear rate on the rheology and morphology of blends of LC–3000, a thermotropic liquid crystalline polymer consisting of 60/40 of hydroxybenzoic acid and poly(ethylene terephthalate), with polypropylene were studied. It was found that the rheological properties depend in a complex manner on composition and applied shear. Both positive and negative deviations from the log-additivity rule were observed at low shear rates. Significant viscosity reduction was measured when the dispersed phase was a nematic TLCP. The accompanying microstructural transitions were characterized a posteriori, and it was found that the state of dispersion of the TLCP phase also influences the viscosity reduction phenomenon. A nematic, fibrillar TLCP phase shows a viscosity reduction of the order of fourfold with respect to the viscosity of the matrix. Another important finding was that the stability of these fibers would not be expected from work on other non-TLCP-containing immiscible blends. This suggests that the unique rheology of the TLCP minor phase is relevant to the formation of stable fibers. © 1996 John Wiley & Sons, Inc.     

The relative role of coalescence and interfacial tension in controlling dispersed phase size reduction during the compatibilization of polyethylene terephthalate/polypropylene blends

The breaking thread and the sessile drop methods have been used to evaluate the interfacial tension between a polypropylene (PP) and a polyethylene-terephthalate (PET). An excellent correlation was found between the two. The breaking thread technique was then used to evaluate the interfacial tension of these blends at various levels of a styrene-ethylene butylene-styrene grafted with maleic anhydride (SEBS-g-MA) compatibilizer. In order to evaluate the relative roles of coalescence and interfacial tension in controlling dispersed phase size reduction during compatibilization, the morphology of PP/PET 1/99 and 10/90 blends compatibilized by a SEBS-g-MA were studied and compared. The samples were prepared in a Brabender mixer. For the 10/90 blend, the addition of the compatibilizer leads to a typical emulsification curve, and a decrease in dispersed phase size of 3.4 times is observed. For the 1/99 blend, a 1.7 times reduction in particle size is observed. In the latter case, this decrease can only be attributed to the decrease of the interfacial tension. It is evident from these results that the drop in particle size for the 10/90 PP/PET blend after compatibilization is almost equally due to diminished coalescence and interfacial tension reduction. These results were corroborated with the interfacial tension data in the presence of the copolymer. A direct relationship between the drop in dispersed phase size for the 1/99 PP/PET blend and the interfacial tension reduction was found for this predominantly shear mixing device. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 2271–2280, 1997     

碳纳米管在聚对苯二甲酸丙二酯/乙烯-醋酸乙烯酯共聚物不相容共混体系中的选择性分散

采用熔融共混法制备了碳纳米管(CNT)填充改性的聚对苯二甲酸丙二酯(PTT)/乙烯-醋酸乙烯酯共聚物(EVA)三元复合材料.通过扫描电子显微镜(SEM)、透射电子显微镜(TEM)、接触角测量仪、旋转流变仪等研究了该复合材料中碳纳米管的分布、不相容的相形态以及流变和力学性能.研究结果表明,与EVA相比,PTT组分具有较低...     

Effect of PBT molecular weight and reactive compatibilization on the dispersed‐phase coalescence of PBT/SAN blends

Poly(butylene terephthalate) (PBT)/styrene‐acrylonitrile copolymer (SAN) blends were investigated with respect to their phase morphology. The SAN component was kept as dispersed phase and PBT as matrix phase and the PBT/SAN viscosity ratio was changed by using different PBT molecular weights. PBT/SAN blends were also compatibilized by adding methyl methacrylate‐co‐glycidyl methacrylate‐co‐ethyl acrylate terpolymer, MGE, which is an in situ reactive compatibilizer for melt blending. In noncompatibilized blends, the dispersed phase particle size increased with SAN concentration due to coalescence effects. Static coalescence experiments showed evidence of greater coalescence in blends with higher viscosity ratios. For noncompatibilized PBT/SAN/MGE blends with high molecular weight PBT as matrix phase, the average particle size of SAN phase does not depend on the SAN concentration in the blends. However noncompatibilized blends with low molecular weight PBT showed a significant increase in SAN particle size with the SAN concentration. The effect of MGE epoxy content and MGE molecular weight on the morphology of the PBT/SAN blend was also investigated. As the MGE epoxy content increased, the average particle size of SAN initially decreased with both high and low molecular weight PBT phase, thereafter leveling off with a critical content of epoxy groups in the blend. This critical content was higher in the blends containing low molecular weight PBT than in those with high molecular weight PBT. At a fixed MGE epoxy content, a decrease in MGE molecular weight yielded PBT/SAN blends with dispersed nanoparticles with an average size of about 40 nm. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010