Modification of poly(vinyl chloride). X. Crosslinking of poly(vinyl chloride) with a soft segment of an elastomer containing thiol groups

To obtain poly(vinyl chloride) (PVC) of excellent toughness, a new method of crosslinking PVC is proposed in which PVC is crosslinked with the soft segment in an elastomer such as liquid Thiokol. The reaction can be accomplished by immersing PVC–Thiokol blends in liquid ammonia at 20–30°C. A similar reaction occurs in aqueous ammonia when hexamethylphosphoramide is used as an activator. Characteristics of the crosslinked PVC thus obtained and of the controls of a similar uncrosslinked composition (PVC–Thiokol LP-8, 100:5 by weight) were as follows: tensile strength, 7.3 and 4.8 kg/mm²; elongation at break, 30 and 2.5%; Young's modulus, 3.5 × 10⁴ and 2.9 × 10⁴ kg/cm²; tensile impact, 88 and 15 kg-cm/cm³, respectively. The crosslinked PVC as plasticized with dioctyl phthalate (DOP) and the control blend (PVC–Thiokol LP-8–DOP, 100:10:10 by weight), respectively, showed tensile strengths of 5.9 and 4.8 kg/mm², elongations at break of 44 and 24%, Young's moduli of 2.5 × 10⁴ and 1.6 × 10⁴ kg/cm², and tensile impact strengths of 62 and 120 kg-cm/cm³. As the crosslinkage through the soft segments increases up to about 5%, the elongation at break, Young's modulus, and tensile impact, in addition to the tensile strength, are improved. This is different from the results so far observed with the crosslinked amorphous polymers and is characteristic of the products of crosslinking through the soft segment. The experimental results are discussed in this paper.     

Biodegradable Polymers for Orthopedic Applications: Synthesis and Processability of Poly (l-Lactide) and Poly (Lactide-co-€-Caprolactone)

Abstract

The synthesis of poly(l-lactide) (PLLA), poly(l-lactide-co-e-caprolactone), and poly(DL-lactide-co-e-caprolactone) by ring-opening bulk polymerization was investigated. Polymerization temperature had a significant effect on the PLLA molecular weight. At 184°C a polymer with a molecular weight of only 10 × 10⁴ resulted. This was lower by a factor of 2 than that obtained at 103 and 145°C. The stannous octoate (SnOct) concentration, with a monomer/SnOct molar ratio in the range of 1,000 to 10,000, was not found to have a significant effect on the PLLA molecular weight. A heterogeneous structure in polymerized PLLA was observed. The intrinsic viscosity of poly(lactide-co-€-caprolactone), obtained at 130°C, monomer/SnOct molar ratio 5,000, and polymerization time of 30 hours, decreased with increasing €-caprolactone content within the first 9 wt% and then leveled off. Die-drawing of PLLA cylinders, for the purpose of increasing the polymer's mechanical strength, was unsuccessful due to the brittleness of the polymer. The drawability of poly(l-lactide), however, was greatly improved by copolymerization with €-caprolactone. With only 3 wt% of €-caprolactone, for example, the tensile strength of die-drawn poly(l-lactide-co-e-caprolactone) was increased by a factor of more than 3. Polymer processing temperature was also investigated. The requirement for low processing temperatures in melt manufacture of controlled release matrix devices containing thermal sensitive drugs was accomplished by three methods: through the use of low molecular weight poly(DL-lactide), adding (DL-lactic) acid oligomer to high molecular weight PDLLA, and copolymerizing DLLA with €-caprolactone. The glass transition temperatures of the modified high molecular weight PDLLA decreased significantly. Melt extrusion below 100°C could be performed.     

Unperturbed dimensions of poly(ethylene oxide)

The intrinsic viscosities of fractions of poly(ethylene oxide) in the molecular weight range 1.5 × 10³ to 10⁶ have been measured at 25°C in benzene, carbon tetrachloride, and acetone; at 35°C in 0.45M aqueous potassium sulfate; and at 50°C in methyl isobutyl ketone and diethylene glycol diethyl ether. The latter three are practically theta solvents. The value of (r₀² /M)^1/2 for poly(ethylene oxide) is calculated to be 0.84 Å from the molecular weights of the high molecular weight fractions, and their intrinsic viscosities in the theta solvents and acetone. Erroneous values result if the usual methods of determination are applied to the data obtained for the low molecular weight (<10⁴) fractions or to the intrinsic viscosities in the very good solvents, benzene and carbon tetrachloride.     

Structure of poly(L‐lactic acid)s prepared by the dehydropolycondensation of L‐lactic acid with organotin catalysts

The synthesis of low‐molecular‐weight (weight‐average molecular weight < 45,000 g/mol) lactic acid polymers through the dehydropolycondensation of L ‐lactic acid was investigated. Polymerizations were carried out in solution with solvents (xylene, mesitylene, and decalin), without a solvent using different Lewis acid catalysts (tetraphenyl tin and tetra‐n‐butyldichlorodistannoxane), and at three different polymerization temperatures (143, 165, and 190 °C). The products were characterized with differential scanning calorimetry, size exclusion chromatography, vapor pressure osmometry, ¹³C NMR, and matrix‐assisted laser desorption/ionization time‐of‐flight (MALDI‐TOF). The resulting polymers contained less than 1 mol % lactide, as shown by NMR. The number‐average molecular weights were calculated from the ratio of the area peaks of ester carbonyl and carboxylic acid end groups via ¹³C NMR. The stereosequences were analyzed by ¹³C NMR spectroscopy on the basis of triad effects. Tetraphenyl tin was an effective transesterification catalyst, and the randomization of the stereosequence at 190 °C was observed. In contrast, the distannoxane catalyst caused comparatively less transesterification reaction, and the randomization of the stereosequences was slow even at 190 °C. The L ‐lactic acid and D ‐lactic acid isomers were added to the polymer chain in a small, blocky fashion. The MALDI‐TOF spectra of poly(L ‐lactic acid) (PLA) chains doped with Na⁺ and K⁺ cations showed that the PLA chains had the expected end groups. The MALDI‐TOF analysis also enabled the simultaneous detection of the cyclic oligomers of PLA present in these samples, and this led to the full structural characterization of the molecular species in PLA. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2164–2177, 2005     

Synthesis and characterization of poly(arylene ether imidazole)s

Poly(arylene ether imidazole)s were prepared by the aromatic nucleophilic displacement reaction of a bisphenol imidazole with activated aromatic dihalides. The polymers had glass transition temperatures ranging from 230 to 318°C and number-average molecular weights as high as 82,000 g/mol. Thermogravimetric analysis showed a 5% weight loss occurring ～ 400°C in air and ～ 500°C in nitrogen. Typical neat resin mechanical properties obtained at room temperature included tensile strength and tensile modulus of 14.2 and 407 ksi and fracture energy (G_lc) of 23 in. lb/in.² Titanium-to-titanium tensile shear strengths measured at 23 and 200°C were 4800 and 3000 psi, respectively. In addition, preliminary data were obtained on carbon fiber laminates. The chemistry, physical, and mechanical properties of these polymers are discussed.     

Synthesis of star‐shaped poly(D,L‐lactic acid‐alt‐glycolic acid)‐b‐poly(L‐lactic acid) with the poly(D,L‐lactic acid‐alt‐glycolic acid) macroinitiator and stannous octoate catalyst

Two types of three‐arm and four‐arm, star‐shaped poly(D,L ‐lactic acid‐alt‐glycolic acid)‐b‐poly(L ‐lactic acid) (D,L ‐PLGA50‐b‐PLLA) were successfully synthesized via the sequential ring‐opening polymerization of D,L ‐3‐methylglycolide (MG) and L ‐lactide (L ‐LA) with a multifunctional initiator, such as trimethylolpropane and pentaerythritol, and stannous octoate (SnOct₂) as a catalyst. Star‐shaped, hydroxy‐terminated poly(D,L ‐lactic acid‐alt‐glycolic acid) (D,L ‐PLGA50) obtained from the polymerization of MG was used as a macroinitiator to initiate the block polymerization of L ‐LA with the SnOct₂ catalyst in bulk at 130 °C. For the polymerization of L ‐LA with the three‐arm, star‐shaped D,L ‐PLGA50 macroinitiator (number‐average molecular weight = 6800) and the SnOct₂ catalyst, the molecular weight of the resulting D,L ‐PLGA50‐b‐PLLA polymer linearly increased from 12,600 to 27,400 with the increasing molar ratio (1:1 to 3:1) of L ‐LA to MG, and the molecular weight distribution was rather narrow (weight‐average molecular weight/number‐average molecular weight = 1.09–1.15). The ¹H NMR spectrum of the D,L ‐PLGA50‐b‐PLLA block copolymer showed that the molecular weight and unit composition of the block copolymer were controlled by the molar ratio of L ‐LA to the macroinitiator. The ¹³C NMR spectrum of the block copolymer clearly showed its diblock structures, that is, D,L ‐PLGA50 as the first block and poly(L ‐lactic acid) as the second block. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 409–415, 2002     

Influence of tertiary diamines on the synthesis of high‐molecular‐weight poly(1,3‐cyclohexadiene)

The living synthesis of poly(1,3‐cyclohexadiene) was performed with an initiator adduct that was synthesized from a 1:2 (mol/mol) mixture of N,N,N′,N′‐tetramethylethylenediamine (TMEDA) and n‐butyllithium. This initiator, which was preformed at 65 °C, facilitated the synthesis of high‐molecular‐weight poly(1,3‐cyclohexadiene) (number‐average molecular weight = 50,000 g/mol) with a narrow molecular weight distribution (weight‐average molecular weight/number‐average molecular weight = 1.12). A plot of the kinetic chain length versus the time indicated that termination was minimized and chain transfer to the monomer was eliminated when a preformed initiator adduct was used. Chain transfer was determined to occur when the initiator was generated in situ. The polymerization was highly sensitive to both the temperature and the choice of tertiary diamine. The use of the bulky tertiary diamines sparteine and dipiperidinoethane resulted in poor polymerization control and reduced polymerization rates (7.0 × 10⁻⁵ s⁻¹) in comparison with TMEDA‐mediated polymerizations (1.5 × 10⁻⁴ s⁻¹). A series of poly(1,3‐cyclohexadiene‐block‐isoprene) diblock copolymers were synthesized to determine the molar crossover efficiency of the polymerization. Polymerizations performed at 25 °C exhibited improved molar crossover efficiencies (93%) versus polymerizations performed at 40 °C (80%). The improved crossover efficiency was attributed to the reduction of termination events at reduced polymerization temperatures. The microstructure of these polymers was determined with ¹H NMR spectroscopy, and the relationship between the molecular weight and glass‐transition temperature at an infinite molecular weight was determined for polymers containing 70% 1,2‐addition (150 °C) and 80% 1,4‐addition (138 °C). © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1216–1227, 2005     

Synthesis and characterization of phthalazinone‐based poly(aryl ether ketone) derived from 4,4′‐dichlorobenzophenone

As distinguished from the conventional preparation of poly(aryl ether ketone)s utilizing 4,4′‐difluorobenzophenone, a novel synthetic method of high molecular weight poly(phthalazinone ether ketone) derived from 4,4′‐dichlorobenzophenone was studied. Reaction conditions to get high molecular weight polymer were investigated in details. Experimentally, sulfolane was chosen as the reaction media and high molecular weight polymer could be obtained in 7–8 hr at 210°C. The cyclic oligomers in the polymer product reduced to below 3.0% when the concentration of the reactant is 1.6–1.7 g/ml. Fourier transform infrared (FT‐IR), ¹H NMR, and elemental analysis were used to confirm the structure of the obtained polymer. The amorphous polymer showed reasonable solubility in selective solvent, such as chloroform and N‐methyl‐2‐pyrrolidone, and tough, flexible, and transparent thin film can be readily prepared from their N‐methyl‐2‐pyrrolidone solution. The obtained polymer showed high glass transition temperature (T_g) up to 261°C detected by differential scanning calorimetry (DSC), and the temperature of 5% weight loss under nitrogen higher than 500°C detected by thermal gravimetric analysis (TGA), indicating its excellent thermal stability. Copyright © 2011 John Wiley & Sons, Ltd.     

Synthesis of well‐defined syndiotactic poly(methyl methacrylate) with low‐temperature atom transfer radical polymerization in fluoroalcohol

The copper‐mediated atom transfer radical polymerization of methyl methacrylate (MMA) in 1,1,1,3,3,3‐hexafluoro‐2‐propanol (HFIP) was studied to simultaneously control the molecular weight and tacticity. The polymerization using tris[2‐(dimethylamino)ethyl]amine (Me₆TREN) as a ligand was performed even at ?78°C with a number‐average molecular weight (M_n) of 13,400 and a polydispersity (weight‐average molecular weight/number‐average molecular weight) of 1.31, although the measured M_n's were much higher than the theoretical ones. The addition of copper(II) bromide (CuBr₂) apparently affected the early stage of the polymerization; that is, the polymerization could proceed in a controlled manner under the condition of [MMA]₀/[methyl α‐bromoisobutyrate]₀/[CuBr]₀/[CuBr₂]₀/[Me₆TREN]₀ = 200/1/1/0.2/1.2 at ?20°C with an MMA/HFIP ratio of 1/4 (v/v). For the field desorption mass spectrum of Cu^IBr/Me₆TREN in HFIP, there were [Cu(Me₆TREN)Br]⁺ and [Cu(Me₆TREN)OCH(CF₃)₂]⁺, indicating that HFIP should coordinate to the Cu^I/Me₆TREN complex. The syndiotacticity of the obtained poly(methyl methacrylate)s increased with the decreasing polymerization temperature; the racemo content was 84% for ?78°C, 77% for ?30°C, 75% for ?20°C, and 63% for 30°C. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1436–1446, 2006     

An efficient solid‐state polycondensation method for synthesizing stereocomplexed poly(lactic acid)s with high molecular weight

Simultaneous solid‐state polycondensation (SSP) of the powdery prepolymers of poly(L ‐lactic acid) (PLLA) and poly(D ‐lactic acid) (PDLA) can produce entire stereocomplexed poly(lactic acid)s (sc‐PLA) with high molecular weight and can be an alternative synthetic route to sc‐PLA. Ordinary melt polycondensations of L ‐ and D ‐lactic acids gave the PLLA and PDLA prepolymers having medium molecular weight which were pulverized for blending in 1:1 ratio. The resultant powder blends were then subjected to SSP at 130–160 °C for 30 h under a reduced pressure of 0.5 Torr. Some of the products thus obtained attained a molecular weight (M_w) as high as 200 kDa, consisting of stereoblock copolymer of PLLA and PDLA. A small amount of the stereocomplex should be formed in the boundaries of the partially melted PLLA and PDLA where the hetero‐chain connection is induced to generate the blocky components. The resultant SSP products showed predominant stereocomplexation after their melt‐processing in the presence of the stereoblock components in spite of containing a small amount of racemic sequences in the homo‐chiral PLLA and PDLA chains. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3714–3722, 2008     

Synthesis and characterization of poly(L‐lactide)s and poly(D‐lactide)s of controlled molecular weight

High molecular weight poly(L ‐lactide)s (PLLAs) and poly(D ‐lactide)s (PDLAs) were synthesized in toluene at 70 °C by ring‐opening polymerization of optically pure L ‐lactide and D ‐lactide, using tin(II) 2‐ethylhexanoate (SnOct₂) and 2‐(2‐methoxyethoxy)ethanol as initiator and coinitiator, respectively. Under these conditions, polarimetry as well as ¹³C NMR spectroscopy indicated that the synthesized poly(lactide)s (PLAs) are more than 99% isotactic. The molecular weight was successfully controlled by adjusting the monomer‐to‐initiator molar ratio. Gel permeation chromatography and MALDI‐TOF mass spectrometry analyses showed that the polydispersity index of the PLAs is below 1.1. Moreover, MALDI‐TOF spectra showed two different chain distributions, one characterized by an even number of lactic acid repeat units and the other by an odd number of lactic acid repeat units. The second distribution, indicative of the presence of intermolecular transesterification reactions, appears at the very beginning of the polymerization and its intensity increases with the polymerization time. Finally, a reversible reaction kinetic model was used to determine the monomer equilibrium concentration ([M]_eq = 1.4 ± 0.5%) and the propagation rate constant (k_p = 14.4 ± 0.5 L mol^?1 h^?1) of the polymerization. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1944–1955, 2007     

Determination of organic acids by capillary electrophoresis with simultaneous addition of Ca and Mg as complexing agents

Summary A capillary electrophoretic method, with divalent cations as complexing agents in the electrolyte, has been developed for separation and determination of the low molecular weight organic acids most commonly found in wine, viz. formic, fumaric, succinic, oxalic, malic, tartaric, acetic, lactic, and citric acids. The separation conditions optimized were electrolyte concentration, organic flow modifier concentration, type and concentration of complexing agents in the electrolyte, and injection time. The best resolution of some of the acids studied was achieved by use of an electrolyte containing tetraborate buffer (10mm) at pH 9.3, an organic flow modifier (tetradecyltrimethylammonium hydroxide), and Ca²⁺ (10 ppm) and Mg²⁺ (10 ppm) as complexing agents. Other conditions used in the method were hydrostatic injection (10 cm height for 30 s), detection at 185 nm, and temperature 20°C. For all the acids studied detector response was linear for the concentration ranges considered. The repeatability of each point on the calibration plot for standards (n=4) was generally better than 1% the method was applied to samples of must, wine, brandy, and vinegar from the Jerez region.     

Synthesis and characterization of aromatic polymers containing pendant silyl groups. I. Polyarylates

Polyarylates containing pendant silyl group were prepared by the phase-transfer catalyzed, two-phase polycondensations of 2,2-bis (4-hydroxyphenyl) propane with corresponding dicarbonyl chlorides such as 2-trimethylsilylterephthaloyl chloride, 5-trimethylsilylisophthaloyl chloride, 5-dimethylphenylsilylisophthaloyl chloride, and 5-triphenylsilylisophthaloyl chloride. The resulting amorphous polyarylates with glass transition temperatures of 163–214°C had inherent viscosities in the range of 0.41–0.95 dL/g. These polyarylates were readily soluble in common chlorinated hydrocarbons and it was possible to obtain transparent, flexible, and tough films from the polymer solutions. The prepared polyarylates showed fairly good thermal stabilities as well as tensile strengths, i.e., the tensile strengths of the cast films from chloroform solution were 6.0–6.7 kg/mm². And TGA data revealed 10% weight losses and residual weights at 800°C were 437–495°C and 27–40% under nitrogen atmosphere, respectively. © 1992 John Wiley & Sons, Inc.     

Synthesis and characterization of high molecular weight poly(1,2-propylene carbonate-<Emphasis Type="Italic">co</Emphasis>-1,2-cyclohexylene carbonate) using zinc complex catalyst

Using supported multi-component zinc dicarboxylate catalyst,poly（1,2-propylene carbonate-co-1,2-cyclohexylene carbonate）（PPCHC） was successfully synthesized from carbon dioxide（CO₂） with propylene oxide（PO） and cyclohexene oxide（CHO）.The conversion of epoxides dramatically increased up to 89.7%（yield:384.2 g of polymer per g of Zn） with increasing reaction temperature from 60℃to 80℃.The optimized reaction temperature is 80℃.The chemical structure,the molecular weight,as well as thermal and mechanical properties of the resulting terpolymers were investigated extensively. When CHO feed content（mol%） is lower than 10%,the PPCHC terpolymers have number average molecular weight（M_n） ranging from 102×10³ to 202×10³ and molecular weight distribution（MWD） values ranging from 2.8 to 3.5.In contrast to poly（propylene carbonate）（PPC）,the introduction of small amount of CHO leads to increase in the glass transition temperature from 38.0℃to 42.6℃.Similarly,the mechanical strength of the synthesized terpolymer is greatly enhanced due to the incorporation of CHO.These improvements in mechanical and thermal properties are of importance for the practical application of PPC.     

Novel miktofunctional initiator for the preparation of an ABC‐type miktoarm star polymer via a combination of controlled polymerization techniques

An ABC‐type miktoarm star polymer was prepared with a core‐out method via a combination of ring‐opening polymerization (ROP), stable free‐radical polymerization (SFRP), and atom transfer radical polymerization (ATRP). First, ROP of ϵ‐caprolactone was carried out with a miktofunctional initiator, 2‐(2‐bromo‐2‐methyl‐propionyloxymethyl)‐3‐hydroxy‐2‐methyl‐propionic acid 2‐phenyl‐2‐(2,2,6,6‐tetramethyl‐piperidin‐1‐yl oxy)‐ethyl ester, at 110 °C. Second, previously obtained poly(ϵ‐caprolactone) (PCL) was used as a macroinitiator for SFRP of styrene at 125 °C. As a third step, this PCL–polystyrene (PSt) precursor with a bromine functionality in the core was used as a macroinitiator for ATRP of tert‐butyl acrylate in the presence of Cu(I)Br and pentamethyldiethylenetriamine at 100 °C. This produced an ABC‐type miktoarm star polymer [PCL–PSt–poly(tert‐butyl acrylate)] with a controlled molecular weight and a moderate polydispersity (weight‐average molecular weight/number‐average molecular weight < 1.37). The obtained polymers were characterized with gel permeation chromatography and ¹H NMR. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4228–4236, 2004     

Poly(enamine-ketones) from aromatic diacetylenic diketones and aromatic diamines

Novel poly(enamine-ketones) were prepared with inherent viscosities as high as 1.99 dL/g using the Michael-type addition of various diamines to 1,1′-(1,3 or 1,4-phenylene)bis(3-phenyl-2-propyn-1-one) in m-cresol at 60–130°C. Tough, clear, amber films with tensile strengths of 12, 400 psi and tensile moduli of 397, 000 psi were cast from solutions of the polymers in chloroform. The polymers exhibited T_gs as high as 235°C and weight losses of 14% after aging at 232°C in circulating air for 60 h. The synthesis and characterization of several poly(enamine-ketones) are discussed.     

Poly(enonsulfides) from the addition of aromatic dithiols to aromatic dipropynones

Novel poly(enonsulfides) were prepared with inherent viscosities as high as 1.35 dL/g by nucleophilic addition of various aromatic dithiols to 1,1′-(1,3- or 1,4-phenylene)bis(3-phenyl-2-propyn-1-one) in m-cresol at 25–40°C. A tough clear yellow film with a tensile strength of 11,300 psi and a tensile modulus of 466,000 psi at 25°C was cast from a chloroform solution of the polymer prepared from 1,3-dithiobenzene and 1,1′-(1,4-phenylene)bis(3-phenyl-2-propyn-1-one). The poly(enonsulfides) exhibited T_g's as high as 180°C and weight losses of approximately 10% at 331°C in air. The synthesis and characterization of several poly(enonsulfides) are discussed.     

Living polymerization of D,L‐3‐methylglycolide initiated with bimetallic (Al/Zn) μ‐oxo alkoxide and copolymers thereof

D,L ‐3‐Methylglycolide (MG) was successfully polymerized with bimetallic (Al/Zn) μ‐oxo alkoxide as an initiator in toluene at 90 °C. The effect of the initiator concentration and monomer conversion on the molecular weight was studied. It is shown that the polymerization of MG follows a living process. A kinetic study indicated that the polymerization approximates the first order in the monomer, and no induction period was observed. ¹H NMR spectroscopy showed that the ring‐opening polymerization proceeds through a coordination–insertion mechanism with selective cleavage of the acyl–oxygen bond of the monomer. On the basis of ¹H NMR and ¹³C NMR analyses, the selective cleavage of the acyl–oxygen bond of the monomer mainly occurs at the least hindered carbonyl groups (P₁ = 0.84, P₂ = 0.16). Therefore, the main chain of poly(D,L ‐lactic acid‐co‐glycolic acid) (50/50 molar ratio) obtained from the homopolymerization of MG was primarily composed of alternating lactyl and glycolyl units. The diblock copolymers poly(ϵ‐caprolactone)‐b‐poly(D,L ‐lactic acid‐alt‐glycolic acid) and poly(L ‐lactide)‐b‐poly(D,L ‐lactic acid‐alt‐glycolic acid) were successfully synthesized by the sequential living polymerization of related lactones (ϵ‐caprolactone or L ‐lactide). ¹³C NMR spectra of diblock copolymers clearly show their pure diblock structures. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 357–367, 2001     

Polymers of carbonic acid. XVII. Polymerization of cyclobis(tetramethylene carbonate) by means of BuSnCl3 and Sn(II) 2-ethylhexanoate

Dimeric cyclotetramethylene carbonate (TeMC)₂ was polymerized in bulk at 185°C. Either nBuSnCl₃ or Sn(II)2-ethylhexanoate (SnOct₂) were used as catalysts. SnOct₂ proved to be somewhat less reactive, but high yields (up to 93%) and high viscosities (ν_inh up to 0.85 dL/g) were obtained with both catalysts. Viscosity-average molecular weights (M_v) in the range of 50–75 × 10³ were determined. The isolated crystalline poly(tetramethylene carbonate)s were characterized by IR, ¹H- and ¹³C-NMR spectra, DSC measurements and WAXD powder pattern. CH₂OH and octoate end groups were detected by means of ¹H-NMR spectroscopy when SnOct₂ was used as initiator, but ether groups were absent. DSC measurements revealed that poly(tetramethylene carbonate) is a slowly crystallizing polymer with a degree of crystallinity below 50% and a melting temperature in the range of 64–69°C depending on the molecular weight. Thermogravimetric analyses proved that polyTeMC decomposes completely between 240 and 340°C without leaving a residue. CO₂ and tetrahydrofuran were the main degradation products. © 1996 John Wiley & Sons, Inc.     

Alkyl-substituted poly(2,5-benzophenone)s synthesized via Ni(0)-catalyzed coupling of aromatic dichlorides and their miscible blends

High molecular weight poly(2,5-benzophenone) derivatives were prepared by Ni(0)-catalyzed coupling of 4′-substituted 2,5-dichlorobenzophenones. Monomers were synthesized by the Friedel–Crafts reaction of 2,5-dichlorobenzoyl chloride and alkyl-substituted benzenes in the presence of aluminum chloride. The resulting polymers are soluble and show no evidence of crystallinity by DSC. Number average molecular weights are in the range of 9.2 × 10³–11.7 × 10³ g/mol by multiple angle laser light scattering (MALLS). Molecular weights obtained by MALLS are only slightly lower (∼90%) than those obtained by GPC (polystyrene standards). These polymers exhibit high thermal stability with glass transition temperatures ranging from 173 to 225°C and weight loss occurring above 450°C in nitrogen and 430°C in air. Additionally, the polymers were blended and the resulting polymer films appear to be miscible by DSC results. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. A Polym. Chem. 36: 2611–2618, 1998