The electrochemistry of uric acid at a gold electrode modified with L-cysteine, and its application to sensing uric urine

The electrochemistry of uric acid at a gold electrode modified with a self-assembled film of L-cysteine was studied by cyclic voltammetry and differential pulse voltammetry. Compared to the bare gold electrode, uric acid showed better electrochemical response in that the anodic peak current is stronger and the peak potential is negatively shifted by about 100 mV. The effects of experimental conditions on the oxidation of uric acid were tested and a calibration plot was established. The differential pulse response to uric acid is linear in the concentration range from 1.0?×?10^?6 to ~?1.0?×?10^?4 mol?L^?1 (r?=?0.9995) and from 1.0?×?10^?4 to ~?5.0?×?10^?4 mol?L^?1 (r?=?0.9990), the detection limit being 1.0?×?10^?7 mol?L^?1 (at S/N?=?3). The high sensitivity and good selectivity of the electrode was demonstrated by its practical application to the determination of uric acid in urine samples.

Rapid voltammetric determination of maltol in some foods and beverages using a poly(methylene blue)/graphene-modified glassy carbon electrode

A novel poly(methylene blue)/graphene composite glassy carbon electrode was fabricated and the electrochemical behavior of maltol at the modified electrode was studied by cyclic voltammetry. In phosphate-buffered solution, the modified electrode exhibited excellent electrocatalytic activity towards the electrochemical oxidation of maltol. Under optimized conditions, the oxidation peak current showed a linear relationship with the concentrations of maltol in the ranges of 8.00?×?10^?7 to 4.00?×?10^?5 and 4.00?×?10^?5 to 5.40?×?10^?4 mol L^?1, with a detection limit of 6.50?×?10^?8 mol L^?1. The performance of the developed method was validated in terms of linearity (r?=?0.9981 and 0.9955), recovery (97.0?99.3 %), reproducibility (relative standard deviations?≤?3.1 %, n?=?6), and robustness. The method shows excellent sensitivity, selectivity, and reproducibility and has been successfully applied to analyzing maltol in a wide variety of food products.     

Solid-state ion selective electrode based on polypyrrole conducting polymer nanofilm as a new potentiometric sensor for Zn2+ ion

A pencil graphite electrode (PGE) electrodeposited by a polypyrrole conducting polymer doped with tartrazine (termed as PGE/PPy/Tar) was prepared and used as a zinc (II) solid-state ion-selective electrode. For the preparation of the zinc sensor electrode, electrodeposition of a polypyrrole nanofilm was carried out potentiostatically (E _app?=?0.75 V vs SCE) in a solution containing 0.010 M pyrrole and 0.001 M tartrazine trisodium salt. A pencil graphite and Pt wire were used as working and auxiliary electrodes, respectively. The introduced electrode in the current paper can be fabricated simply and was found to possess high selectivity, exhibited wide working concentration range, sufficiently rapid response, potential stability, and very good sensitivity to Zn (II) ion. The sensor electrode showed a linear Nernstian response over the range of 1.0?×?10^?5 to 1.0?×?10^?1 M with a slope of 28.23 mV per decade change in zinc ion concentration. A detection limit of 8.0?×?10^?6 M was obtained. The optimum pH working of the electrode was found to be 5.0.     

Sensitive voltammetric assay of etoposide using modified glassy carbon electrode with a dispersion of multi-walled carbon nanotube

A sensitive electroanalytical method for the determination of anticancer drug etoposide (ETP) using adsorptive stripping differential pulse voltammetry (AdSDPV) at a multi-walled carbon nanotube-modified glassy carbon electrode (MWCNT-modified GCE) is presented. The surface morphology of modified electrode was characterized by scanning electron microscopy. The effects of accumulation time and potential, pH, scan rate, and amount of MWCNT suspension were investigated. The calibration curve was linear in the concentration range of 2.0?×?10^?8–2.0?×?10^?6 M with the detection limit of 5.4?×?10^?9 M. The reproducibility of the peak current was found at 1.55 % (n?=?5) RSD value in pH 6.0 Britton–Robinson buffer for the MWCNT-modified GCE. The method was then successfully utilized for the determination of ETP in pharmaceutical dosage form, and a recovery of 99.55 % was obtained. The possible oxidation mechanism of ETP was also discussed. The proposed electroanalytical method using MWCNT-modified GCE is the most sensitive method for the determination of ETP with lowest limit of detection in the previously published electrochemical methods.     

Simultaneous voltammetric determination of uric acid and ascorbic acid using carbon paste/cobalt Schiff base composite electrode

Differential pulse and cyclic voltammetry were applied for the oxidation of mixture of uric acid and ascorbic acid at the surface of carbon paste/cobalt Schiff base composite electrode. The electrooxidation of these compounds at bare electrode is sluggish, and there is no suitable peak separation between them. However, using cobalt methyl salophen as modifier, two well-defined anodic waves with a considerable enhancement in the peak current and a remarkable peak potential separation near 315 mV are obtained. It can improve the kinetics of electron transfer for both compounds remarkably. All these improvements are created because of the electrocatalytic property of cobalt Schiff base complex. The effect of some parameters such as pH and scan rates were studied. All the anodic peak currents for the oxidation of ascorbic acid and uric acid shifted toward more negative potential with an increase in pH, revealing that protons have taken part in their electrode reaction processes. The best peak separation with appropriate current was obtained for pH 4.0. A linear range of 5.0?×?10^?4 to 1.0?×?10^?8 and 1.0?×?10^?3 to 1.0?×?10^?8 M with detection limit of 8.0?×?10^?9 and 8.0?×?10^?9 M was obtained for ascorbic acid and uric acid using differential pulse voltammetry at the surface of modified electrode, respectively. Analytical utility of the modified electrode has been examined successfully using human urine samples and vitamin C commercial tablets.     

One-step construction of an electrode modified with electrodeposited Au/SiO2 nanoparticles, and its application to the determination of NADH and ethanol

A new electrode was developed by one-step potentiostatic electrodeposition (at ?2.0 V for 20 s) of Au/SiO₂ nanoparticles on a glassy carbon electrode. The resulting electrode (nano-Au/SiO₂/GCE) was characterized by scanning electronic microscopy, X-ray photoelectron spectroscopy and electrochemical techniques. The electrochemical behavior of dihydronicotinamide adenine dinucleotide (NADH) at the nano-Au/SiO₂/GCE were thoroughly investigated. Compared to the unmodified electrode, the overpotential decreased by about 300 mV, and the current response significantly increased. These changes indicated that the modified electrode showed excellent catalytic activity in the oxidation of NADH. A linear relationship was obtained in the NADH concentration range from 1.0?×?10^?6 to 1.0?×?10^?4 mol?L^?1. In addition, amperometric sensing of ethanol at the nano-Au/SiO₂/GCE in combination with alcohol dehydrogenase and nicotinamide adenine dinucleotide was successfully demonstrated. A wide linear response was also found for ethanol in the range from 5.0?×?10^?5 to 1.0?×?10^?3 mol?L^?1 and 1.0?×?10^?3 to 1.0?×?10^?2 mol?L^?1, respectively. The method was successfully applied to determine ethanol in beer and biological samples.     

Simultaneous determination of dopamine, uric acid and ascorbic acid with LaFeO3 nanoparticles modified electrode

LaFeO₃ nanoparticles of approximately 22 nm in size were synthesized and characterized by XRD and TEM. A novel glassy carbon electrode modified with LaFeO₃ nanoparticles was constructed and characterized by electrochemical impedance spectroscopy and cyclic voltammetry. The modified electrode exhibited strong promoting effect and high stability toward the electrochemical oxidation of dopamine (DA), which gave reversible redox peaks with a formal potential of 0.145 V (vs. Ag/AgCl) in pH 7.0 phosphate buffer solution. The anodic peak current (measured by constant potential amperometry) increased linearly with the concentration of dopamine in the range from 1.5?×?10^?7 to 8.0?×?10^?4 M. The detection limit was 3.0?×?10^?8 M. The relative standard deviation of eight successive scans was 3.47% for 1.0?×?10^?6 M DA. The interference by ascorbic acid was eliminated efficiently. The method was used to determine DA in dopamine hydrochloride injections and showed excellent sensitivity and recovery.     

Micelle-encapsulated multi-wall carbon nanotubes with photosensitive copolymer and its application in the detection of dopamine

Photosensitive copolymer P(St-alt-MAn)-co-P(VM-alt-MAn) was synthesized and employed to disperse multi-wall carbon nanotubes (MWCNTs). It was found that copolymer could form micelles in aqueous solution and adsorb onto the surface of MWCNTs to produce micelle-encapsulated MWCNTs (e-MWCNTs) by in situ photo crosslinking after irradiation with ultraviolet light and a stable suspension of e-MWCNTs in aqueous solution was obtained. When deposited onto polyaniline (PANI)-modified glassy carbon electrodes, a thin film of e-MWCNTs composite was obtained and the performance of the e-MWCNTs/PANI electrode toward dopamine was then evaluated. The experimental results suggest that the hybrid film modified electrode exhibits a dramatic electrocatalytic effect on the oxidation of dopamine (DA), as evidenced by a marked enhancement of the current response. A series of CVs was obtained by modified glassy-carbon electrodes with different size of micelles was also researched. The result shows that the peak current increased with the increasing size of micelles. A linear calibration plot was obtained in a wide range of 1.0?×?10^?7–1.0?×?10^?3 M and the detection limit was 5.0?×?10^?8 M. In addition, the interference from ascorbic acid (AA) was effectively suppressed due to the presence of the negatively charged carboxylate groups of copolymer on the outside of MWCNTs which repels AA anions and provides a transport channel only for DA cations.     

Direct electrochemical behavior of cytochrome c, and its determination on phytic acid modified electrode

Phytic acid (PA) with its unique structure was attached to a glassy carbon electrode (GCE) to form PA/GCE modified electrode which was characterized by electrochemical impedance. The electrochemical behavior of cytochrome c (Cyt c) on the PA/GCE modified electrode was explored by cyclic voltammetry and differential pulse voltammetry. The Cyt c displayed a quasi-reversible redox process on PA modified electrode pH 7.0 phosphate buffer solution with a formal potential (E ^0′) of 57 mV (versus Ag/AgCl). The peak currents were linearly related to the square root of the scan rate in the range of 20–120 mV·s^?1. The electron transfer rate constant was determined to be 12.5 s^?1. The PA/GCE modified electrode was applied to the determination of Cyt c, in the range of 5?×?10^?6 to 3?×?10^?4 M, the currents increase linearly to the Cyt c concentration with a correlation coefficient 0.9981. The detection limit was 1?×?10^?6 M (signal/noise?=?3).     

Voltammetric determination of trace doxorubicin at a nano-titania/nafion composite film modified electrode in the presence of cetyltrimethylammonium bromide

A sensitive electrochemical method was developed for the determination of doxorubicin at a glassy carbon electrode (GCE) modified with a nano-titania (nano-TiO₂)/nafion composite film. Nano-TiO₂ was dispersed into nafion to give a homogeneous suspension. After solvent evaporation, a uniform film of nano-TiO₂/nafion composite was obtained on the GCE surface. The nano-TiO₂/nafion composite film modified GCE exhibited excellent electrochemical behavior toward the reduction of doxorubicin. Compared to the reduction of doxorubicin at the bare GCE, the reduction current of doxorubicin at the nano-TiO₂/nafion composite film modified GCE was greatly enhanced. Based on this, a novel voltammetric method was applied to the determination of doxorubicin. The experimental parameters that influence the reduction current of doxorubicin, were optimized. Under optimal conditions, a linear response of doxorubicin was obtained in the range from 5.0?×?10^?9 to 2.0?×?10^?6 mol L^?1 (R?=?0.998) and with a limit of detection (LOD) of 1.0?×?10^?9 mol L^?1(S/N?=?3). The RSD of the measurement is 4.7%, and the RSD of the inter-electrode is of 5.1% which indicate the reproducibility of this method. The current response decreased only by around 3.8% of its initial response after 2 weeks exposing the electrode in air. The procedure was applied to assay doxorubicin in human plasma samples with the recoveries of 94.9–104.4%.     

Voltammetric and amperometric determination of uric acid at a carbon-ceramic electrode modified with multi walled carbon nanotubes

The voltammetric behavior of uric acid (UA) was studied at a carbon-ceramic electrode modified with multi walled carbon nanotubes; which was developed via a simple procedure. UA can be effectively oxidized at the surface of the electrode and produced an anodic peak at about 0.29 V in pH 6.8 phosphate buffer solutions. The experimental parameters such as pH, accumulation time, and amount of multi walled carbon nanotubes were optimized for determination of UA. Under the optimum conditions, the anodic peak current in differential pulse voltammetry is linear to the UA concentration over the range from 2.5×10?7M to 1.0×10?4 M with a correlation coefficient of 0.998. The electrode exhibited good stability and could be easily regenerated. The relative standard deviation of the peak current obtained for a 5.0?×?10^?5 M UA solution was 1.0%. The influence of dopamine and ascorbic acid on the anodic peak current of UA was examined. This method was successfully applied for the determination of uric acid in human urine sample, and the recovery was 99.9%.     

MCM/ZrO2 nanoparticles modified electrode for simultaneous and selective voltammetric determination of epinephrine and acetaminophen

A novel MCM/ZrO₂ nanoparticles modified carbon paste electrode (MZ-CPE) was fabricated and used to study the electro oxidation of epinephrine (EP) and acetaminophen (AC) and their mixtures by electrochemical methods. The modified electrode showed electrocatalytic activity toward EP and AC oxidation with a decrease of the overpotential by 173 mV to a less positive potential for EP at the surface of the MZ-CPE and an increase in peak current at pH 7.0. Differential pulse voltammetry peak currents of EP and AC increased linearly with their concentrations in the ranges of 1.0 × 10^?6–2.5 × 10^?3 and 1.0 × 10^?6–2.0 × 10^?3 M, respectively, and the detection limits for EP and AC were 5.0 × 10^?7 and 4.5 × 10^?7 M, respectively.     

Simultaneous Determination of Hydroquinone and Catechol at a Glassy Carbon Electrode Modified with Multiwall Carbon Nanotubes

A simply and high selectively electrochemical method for simultaneous determination of hydroquinone and catechol has been developed at a glassy carbon electrode modified with multiwall carbon nanotubes (MWNT). It was found that the oxidation peak separation of hydroquinone and catechol and the oxidation currents of hydroquinone and catechol greatly increase at MWNT modified electrode in 0.20 M acetate buffer solution (pH 4.5). The oxidation peaks of hydroquinone and catechol merge into a large peak of 302 mV (vs. Ag/AgCl, 3 M NaCl) at bare glassy carbon electrode. The two corresponding well‐defined oxidation peaks of hydroquinone in the presence of catechol at MWNT modified electrode occur at 264 mV and 162 mV, respectively. Under the optimized condition, the oxidation peak current of hydroquinone is linear over a range from 1.0×10^?6 M to 1.0×10^?4 M hydroquinone in the presence of 1.0×10^?4 M catechol with the detection limit of 7.5×10^?7 M and the oxidation peak current of catechol is linear over a range from 6.0×10^?7 M to 1.0×10^?4 M catechol in the presence of 1.0×10^?4 M hydroquinone with the detection limit of 2.0×10^?7 M. The proposed method has been applied to simultaneous determination of hydroquinone and catechol in a water sample with simplicity and high selectivity.     

Electrochemical behavior of adriamycin at an electrode modified with silver nanoparticles and multi-walled carbon nanotubes, and its application

An electrochemical sensor has been constructed for the determination of adriamycin (ADM) that is based on a glassy carbon electrode modified with silver nanoparticles and multi-walled carbon nanotubes with carboxy groups. The modified electrode was characterized by scanning electron microscopy and exhibits a large enhancement of the differential pulse voltammetric response to ADM. Signals are linear with the concentrations of ADM in the range from 8.2?×?10^?9 M to 19.0?×?10^?9 M, with a detection limit of 1.7?×?10^?9 M. The sensor is highly reproducible and exhibits excellent stability. It was to detect calf thymus DNA.     

A novel palladium nanoparticles-polyproline-modified graphite electrode and its application for determination of curcumin

A novel-modified electrode has been developed, by electrodeposition of palladium nanoparticles (PdNps) on polypyroline film-coated (Poly(Pr)) graphite electrode. The modified electrode (PdNps/Poly(Pr)/GE) was characterized by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM) techniques. SEM proved that the palladium nanoparticles were uniform distributed with an average particle diameter of 20–45 nm. A higher catalytic activity was obtained for curcumin oxidation using this new modified electrode (PdNps/Poly(Pr)/GE). The square wave voltammogram of curcumin in pH 2 phosphate buffer exhibited an anodic peak at 0.504 V. This oxidation peak current was found to be linearly related to curcumin concentrations in the ranges of 5.0?×?10^?9 to 1.0?×?10^?7 M with a detection limit of 1.2?×?10^?9 M. This novel-modified electrode showed excellent sensitivity, compared with the existing reports about determination of curcumin.     

Determination of Tyrosine in the Presence of Sodium Dodecyl Sulfate Using a Gold Nanoparticle Modified Carbon Paste Electrode

A carbon paste electrode modified with gold nanoparticles (AuMCPE) was used as a highly sensitive sensor for determination of Tyrosine (Tyr), in the presence of an anionic surfactant, sodium dodecyl sulfate (SDS), in aqueous solution. The measurements were carried out by using of differential pulse voltammetry (DPV), cyclic voltammetry (CV), amd chronocoulometry and chronoamperometry methods. The prepared electrode shows voltammetric responses with high sensitivity and selectivity for Tyr in the presence of SDS. The relationship between the oxidation peak current of Tyr and its concentration was obtained linearly and it was 1.0 × 10^?7 to 1.0 × 10^?5 M with a detection limit of 5.5 × 10^?8 M in the absence of SDS. On the other hand the oxidation peak current of Tyr increased significantly at AuMCPE in the presence of SDS and its detection limit was reduced to 2.7 × 10^?9 M. The proposed voltammetric approach was also applied to the determination of Tyr concentration in human serum.     

Direct electrochemistry and electrocatalysis of hemoglobin on a gold ion implantation-modified indium tin oxide electrode

In this paper, a gold nanoparticle-modified indium tin oxide electrode (Au/ITO) was prepared without the use of any cross-linker or stabilizer reagent. The prepared Au/ITO was used as a new platform to achieve the direct electron transfer between Hb and the modified electrode. The proposed electrode exhibited a pair of well-defined redox peaks with a formal potential of ?0.073 V (vs. Ag/AgCl). The immobilized Hb showed excellent electrocatalytic activity toward H₂O₂ and the electrocatalytic current values were linear with the increasing concentration of H₂O₂ ranging from 1.0?×?10^?6?M to 7.0?×?10^?4?M. The detection limit was 2.0?×?10^?7?M (S/N?=?3) and the Michaelis–Menten constant was calculated to be 0.2 mM. The proposed electrode also showed high selectivity, long-term stability, and good reproducibility.     

Electrochemical Oxidation of Tryptophan and Its Analysis in Pharmaceutical Formulations at a Poly(Methyl Red) Film-Modified Electrode

A poly(methyl red) film-modified glassy carbon electrode was fabricated and the oxidation behavior of tryptophan at the modified electrode was investigated by cyclic and linear sweep voltammetry. The oxidation peak current of tryptophan at the modified electrode increased significantly, and the oxidation process was irreversible and adsorption-controlled. An analytical method was developed for the determination of tryptophan in a phosphate buffer solution at pH 3.5. The anodic peak current varied linearly with a tryptophan concentration in the range 1.0 × 10^?7 to 1.0 × 10^?4 mol/L with a limit of detection of 4.0 × 10^?8 mol/L. The proposed method was successfully applied to determine tryptophan in composite amino acid injections.     

Electrochemical Analysis of D‐Penicillamine Using a Carbon Paste Electrode Modified with Ferrocene Carboxylic Acid

The electrochemical behavior of D ‐penicillamine (D ‐PA) studied at the surface of ferrocene carboxylic acid modified carbon paste electrode (FCAMCPE) in aqueous media using cyclic voltammetry and double step potential chronoamperometry. It has been found that under optimum condition (pH 7.00), the oxidation of D ‐PA at surface of such an electrode is occurred about 420 mV less positive than that an unmodified carbon paste electrode (CPE). The catalytic oxidation peak current was linearly dependent on the D ‐PA concentration and a linear calibration curve was obtained in the ranges 7.5×10^?5 M – 1.0×10^?3 M and 6.5×10^?6 M?1.0×10^?4 M of D ‐PA with cyclic voltammetry (CV) and differential pulse voltammetry (DPV) methods respectively. The detection limits (3σ) were determined as 6.04×10^?5 M and 6.15×10^?6 M. This method was also used for the determination of D ‐PA in pharmaceutical preparation (capsules) by standard addition method.     

Determination of pesticides in vegetable samples using an acetylcholinesterase biosensor based on nanoparticles ZrO2/chitosan composite film

An amperometric pesticides inhibition biosensor has been developed and used for determination of pesticides in vegetable samples. To eliminate the interference of ascorbic acid, multilayer films of polyelectrolyte (chitosan/polystyrensulfonate) were coated on the glass carbon electrode. Then, acetylcholinesterase was immobilized on the electrode based on surface-treated nanoporous ZrO₂/chitosan composite film as immobilization matrix. As a modified substrate, acetylthiocholine was hydrolysed by acetylcholinesterase and produced thiocholine which can be oxidized at +700?mV vs. SCE. Pesticides inhibit the activity of enzyme with an effect of decreasing of oxidation current. The experimental conditions were optimized. The electrode has a linear response to acetylthiocholine within 9.90?×?10^?6 to 2.03?×?10^?3?M. The electrode provided a linear response over a concentration range of 6.6?×?10^?6 to 4.4?×?10^?4?M for phoxim with a detection limit of 1.3?×?10^?6?M, over a range of 1.0?×?10^?8 to 5.9?×?10^?7?M for malathion, and over a range of 8.6?×?10^?6 to 5.2?×?10^?4?M for dimethoate. This biosensor has been used to determine pesticides in a real vegetable sample.