Pt羰基簇合物在NaY内的合成机理

利用IR，EXAFS, ~(13)CO同位素交换反应及与NO作用等手段研究了Pt羰基簇合物[Pt_3(CO)_6]~(2-)_n(n＝3,4)在NaY分子筛超笼内的合成机理．在氧化样品Pt~(2+)/NaY上300－373 K的还愿羰基化过程中，首先Pt~(2+)与CO反应生成PtO(CO)物种(波数σ_(CO)＝2110 cm~(-1))，然后聚集成“Pt_3(CO)_6”(σ_(CO)＝2112，1896和1841 cm~(-1))，最后生成深绿色的Pt羰基簇合物Pt_(12)(CO)_(24)]~(2-)/NaY(σ_(CO)＝2080，1824 cm~(-1))．“Pt_3(CO)_6”的羰基在室温下能迅速地与~(13)CO发生交换，而[Pt_3(CO)_6]~(2-)_n(n＝3,4)的羰基与~(13)CO的同位素交换即使在343 K也进行得很慢，室温下，NO能逐步破坏Pt羰基簇合物的层间和层内Pt－Pt键，得到中间物种“Pt_3(CO)_6”和PtO(CO)，同时在气相产生CO_2和N_2O．而由上述两中间物种出发，300－353 K温度下，在CO气氛中的还原羰基化又能可逆地得到原羰基簇合物．     

外掺Y2O3对镍氢电池正极高温性能的影响

研究了外掺Y2O3对镍氢电池镍正极高温性能的影响. 通常镍正极在高温下放电比容量会骤然降低, 为了提高其高温性能, 进行了球型Ni(OH)2外掺不同比例Y2O3的实验, 对压制的镍电极在不同温度下的充放电情况进行了细致的研究. 研究发现外掺Y2O3的球型Ni(OH)2电极比普通球型Ni(OH)2电极的放电比容量在高温下要高出很多, 在0.2 C充放电情况下外掺1%是最佳比例, 它比普通球型Ni(OH)2电极的放电比容量要高出35%以上, 在1 C充放电情况下外掺0.2%是最佳比例, 它比普通球型Ni(OH)2电极的放电比容量要高出15%以上. 同时对外掺Y2O3提高镍正极放电比容量的原因也进行了初步探讨.     

稀土氧化物对二次锌电极性能的影响

应用阴极极化法在锌电极上覆盖一层稀土氢氧化物膜La(OH)3或Ce(OH)3,并用循环伏安、动电位极化、定电位阴极极化实验研究其电化学性能.结果表明,La(OH)3或Ce(OH)3膜能抑制锌酸根离子的迁移,提高析氢过电位,降低腐蚀电流密度并能抑制枝晶生长.SEM观测显示,稀土氧化物La2O3或CeO2改变了锌沉积形态,进而提高了锌酸钙电极的充放电循环性能.     

液相热分解纳米铁镍合金的形貌可控合成及其磁学性能研究

以Fe(CO)₅和Ni(HCOO)₂为前驱物,十八烯为溶剂,在表面活性剂和分散剂油酸和油胺的协同作用下,通过前驱体的液相热分解和自合金化,制备铁镍合金纳米颗粒。通过XRD和TEM研究了产物的微观结构,并对产物的磁学性质进行了表征。结果表明,在反应温度为200 ℃,油胺与油酸及甲酸镍的物质的量比为4∶2∶1,反应时间为20 min时可得形貌可控、抗氧化性强的面心立方晶体结构的平面三角形纳米铁镍合金,晶粒尺寸为15~55 nm。磁性测量表明,300 K时三角形形貌铁镍合金的饱和磁化强度为15.5 emu·g^-1,矫顽力趋近于零,呈现超顺磁性;在低温(4.2 K)时,铁镍合金的饱和磁化强度为17.5 emu·g^-1,矫顽力增大明显。     

Ni-Co-B非晶态合金催化剂用于氯代硝基苯液相加氢制氯代苯胺

 用化学还原法制备了 Ni-Co-B 非晶态合金催化剂,并采用透射电子显微镜、扫描电子显微镜、选区电子衍射、X射线衍射、X射线能谱和差热-热重分析等表征手段研究了催化剂的非晶性质和原子组成等. 将此催化剂用于邻氯硝基苯和 3,4-二氯硝基苯的液相催化加氢反应,结果表明,当Co/(Co+Ni)=0.5 (摩尔比)时, Ni-Co-B 催化剂具有较好的加氢性能和较高的抑制脱卤性能. 在不加脱卤抑制剂的情况下,两种氯代硝基苯的转化率均接近100%, 脱卤率分别为1.12%和0.42%, 优于使用 Ni-B 和 Co-B 非晶态合金催化剂时的结果. 还讨论了将Co引入到 Ni-B 非晶态合金催化剂时对其性能的影响.     

新型非对称电化学电容器的电极匹配研究

活性炭负极容量的有效利用率是导致双电层电化学电容器和C/Ni(OH)2非对称电化学电容器容量性质差异的主要因素,并可将其作为非对称电化学电容器容量设计和测算的依据;本文引入Ni(OH)2正极有效活性物质概念,以正极有效活性物质的量匹配负极的设计容量,从而优化正、负极的容量匹配,改善非对称电化学电容器的容量和大电流性能.     

A Study on Kinetics of the Bronze Powder-Corrosion Development

HCl acid was applied to the surface of the self-prepared Cu-Sn-Pb alloy, and the methods of IR-REF, IR-PAS, XRD, SPM, SEM, TEM and pH were employed to study the forming process and the developing speed of the bronze powder-corrosion Cu_2(OH)_3Cl (PC). It is found that the corrosion develops fast in acid environment at room temperature; the corrosion Cu_2(OH)_3Cl with valence Cu~(2+) forms from alloy through the intermediate corrosion CuCl with valence Cu~+; PC is contagious, which can pollute the fresh bronze alloy from the corroded sample by air; when CuCl is oxidized to produce Cu_2(OH)_3Cl, Cu~(2+) cation forms at the same time, and both the oxidizing reactions have zero-order reaction with respect to O_2 in the air; the P1 formation reaction has first-order reaction with respect to Cull; in enormous distilled water Cu_2(OH)_3Cl forms from CuCl through the intermediate product Cu_2O.All the results above are discussed in the present article, and the mechanism of PC formation is studied further. The r     

表面覆CoOOH的球形Ni(OH)2的制备及快充性能

应用化学沉淀-电化学氧化法,于球形N i(OH)2颗粒表面生成CoOOH包覆层,研究包覆处理对AA型高容MH/N i电池快充性能的影响,并由红外光谱和扫描电镜表征覆钴样品.结果表明,以包覆CoOOH的N i(OH)2作正极活性材料装配的电池较之于正极单一添加CoO的电池,其内阻降低了约3.4 mΩ,该电池快充时充电电压平台较低且在充电末期电池温度不超过55℃,首次放电效率达90.6%,快充循环寿命达300周次.     

Ni(OH)_2电极材料的XRD和Raman光谱表征

用 XRD和 Raman光谱等方法对几种典型球形 Ni( OH) 2 电极材料进行了表征 ,并分析了材料的表观形貌、掺杂元素和微观结构等对其充放电性能的影响 .结果表明 ,有较好填充性和充放电性能 Ni( OH) 2 电极材料所具有的特征为 ,颗粒的球形好且结晶完好 ,晶粒较小 ,较大的晶格参数 c,并在 51 0和 3596cm- 1 处可以生成 Raman光谱峰 ;而 XRD和 Raman光谱方法则是评价 Ni( OH) 2 电极材料性能的有效手段 .     

AucorePtshell础纳米粒子对甲醇氧化的电催化性能研究

应用两步化学还原法制备不同厚度的AucorePtshell纳米粒子，经紫外可见光谱（UV-Vis）、透射电子显微镜（TEM）表征．该金纳米颗粒经化学还原包裹铂后平均粒径明显增大，调节金与铂的含量可获得不同包裹厚度的AucorePtshell纳米粒子．循环伏安法研究表明，粒径为70-80nm的AucorePtshell纳米粒子对甲醇的氧化具有较好的电催化活性，并且其电催化性能随着电位循环扫描次数的增加而增强．     

Crystal formation and growth during the hydrothermal synthesis of beta-Ni(OH)2 in one-dimensional nano space

Hydrothermal synthesis of beta-Ni(OH)(2) was performed inside uniform carbon-coated nanochannels of an anodic aluminium oxide film. The time course of crystal formation and growth of Ni(OH)(2) in such one-dimensional nano space was observed using transmission electron microscopy (TEM), and the changes in the number and size of crystals with the hydrothermal reaction period were quantitatively analyzed using the TEM images. Moreover, the effect of the channel size (25, 100 and 300 nm in diameter) on the crystal growth was examined. In the early stage of the reaction, the crystal formation and growth of beta-Ni(OH)(2) in the one-dimensional channels took place in the same manner as in conventional hydrothermal synthesis. However, except for the 300 nm-channels, further crystal growth was hampered by the spatial restriction, and it allowed only the growth toward the channel axis. In the case of the 25 nm-channels, many Ni(OH)(2) crystals of less than 40 nm formed initially, but slowly disappeared except for a few that grew larger at the expense of the small crystals. This finding clearly indicates that the crystal growth of Ni(OH)(2) during the whole hydrothermal process was governed by the Ostwald ripening. With this mechanism and the spatial restriction, single crystals of beta-Ni(OH)(2) nanorods with a length of over 150 nm were finally formed.     

Aucore Ptshell纳米粒子对甲醇氧化的电催化性能研究

应用两步化学还原法制备不同厚度的AucorePtshell纳米粒子,经紫外可见光谱(UV-V is)、透射电子显微镜(TEM)表征.该金纳米颗粒经化学还原包裹铂后平均粒径明显增大,调节金与铂的含量可获得不同包裹厚度的AucorePtshell纳米粒子.循环伏安法研究表明,粒径为70~80 nm的AucorePtshell纳米粒子对甲醇的氧化具有较好的电催化活性,并且其电催化性能随着电位循环扫描次数的增加而增强.     

锂离子电池富锂正极材料Li[NixLi1/3-2x/3Mn2/3-x/3]O2(x=1/5, 1/4, 1/3)的合成及电化学性能

通过共沉淀法制备了M(OH)2(M=Mn, Ni)前驱体, 并与LiOH混合, 合成了锂离子电池富锂正极材料Li[NixLi1/3-2x/3Mn2/3-x/3]O2, 采用XRD、SEM和充放电实验对其进行表征. 研究结果表明, Li, Ni, Mn原子在M层中呈有序分布, 形成超结构; 富锂正极材料由亚微米的一次粒子团聚组成1~3 μm颗粒; 在2.0~4.8 V电位范围内, 充放电电流密度为10 mA/g时, 富锂正极材料表现出很高的可逆比容量, 达到200~240 mA·h/g, 同时具有良好的循环可逆性能.     

NiO纳米片和多孔纳米片自组装的空心微球的无模板水热法制备与磁学性质

报道一种非常简单的制备NiO和Ni(OH)₂空心微球的无模板水热法, 即通过NiCl₂与氨水在140 ℃水热反应12 h, 制备了Ni(OH)₂纳米片自组装的空心微球, 经400 ℃热处理2 h得到了NiO空心微球. 采用X射线衍射仪、扫描电镜和透射电子显微镜对产物进行表征, 并在室温下测试了它的磁学性能, 结果表明, Ni(OH)₂空心微球的直径约为3～4 μm, 它是由尺寸1.1～1.3 μm左右的六方相结构的Ni(OH)₂纳米片组装而成; NiO空心微球是由立方相纳米片和多孔纳米片组装而成, 它具有弱的铁磁性, 其矫顽力为583 Oe, 剩余磁化强度为0.213 emu/g. 研究了氨在Ni(OH)₂纳米片的形成与组装过程中的作用, 提出了可能的生长机理.     

XPS study on surface modification of NiTi alloy by acidic solution immersion and subsequent heating in air

Changes in the surface chemical state of a nearly equiatomic nickel–titanium (NiTi) alloy caused by immersion in aqueous solutions of HNO₃ and H₂SO₄ as well as subsequent heating in air at 723 K were analyzed using X-ray photoelectron spectroscopy (XPS). An XPS analysis using angle-resolved technique and a mathematical deconvolution technique revealed that a passive layer formed in an ambient atmosphere contained TiO₂ as a major state and Ni(OH)₂ and NiO as minor states. The Ni(OH)₂ on the alloy remained in the region even when heated in air at 723 K. Therefore, the resulting layer became a Ti-oxide layer with Ni segregated region at the surface, which was NiO formed via dehydration of Ni(OH)₂. However, immersion in an aqueous solution of HNO₃ or H₂SO₄ enables Ni(OH)₂ state to dissolve in the passive layer of a NiTi alloy; thereby, the Ni segregated region rarely appeared in the oxide layer by heating. The Ni segregated region at the surface becomes an obstacle for the inward diffusion of oxygen; thus, the annihilation of such a segregated region results in an increase in the thickness of the oxide layer.     

氧原子在具有Pt皮肤的Pt3Ni(111)表面的吸附和扩散

用基于密度泛函理论的第一性原理方法研究了氧原子在具有Pt皮肤的Pt3Ni(111)[记为Pt-skin-Pt3Ni(111)]表面的吸附和扩散特性. 重点研究了氧原子在Pt-skin-Pt3Ni(111)表面的扩散问题, 这对理解Pt-skin-Pt3Ni(111)催化剂的高催化活性有重要意义. 结果表明: 氧原子容易吸附在fcc位; 催化剂Pt3Ni中的Ni原子对催化剂的电子结构有很大影响, 从而改变了其对氧原子的吸附. 用推拉弹性带(NEB)方法搜索氧原子的扩散势垒, 并解释了Pt-skin-Pt3Ni(111)催化剂的高催化活性.     

Preparation and characterization of nanostructured Ni(OH)2 and NiO thin films by a simple solution growth process

Nanostructured Ni(OH)2 thin films were prepared by a simple solution growth process with F(-) and NH3 used as Ni2+ coordination agents, and ammonia hydroxide solution used as OH(-) supplier to accelerate the hydrolyzation of nickel complex species. The results showed Ni(OH)2 thin films were constructed mainly with hexagonal beta-Ni(OH)2 nanorods; the F(-) and NH3 in reactive solutions played important roles in the film growth process; and solution pH had great influence on the morphologies of thin films, which was explained by the competition of Ni(OH)2 nucleation and growth in solutions. NiO crystallinity thin films were obtained by annealing Ni(OH)2 thin films at 400 degrees C for 2 h and the morphologies of the Ni(OH)2 thin films were sustained well during the annealed process.     

Detection of OH stretching mode of CH3OH chemisorbed on Ni3+ and Ni4+ by infrared photodissociation spectroscopy

Structures of nickel cluster ions adsorbed with methanol, Ni3+ (CH3OH)m (m = 1-3) and Ni4+ (CH3OH)m (m = 1-4) were investigated by using infrared photodissociation (IR-PD) spectroscopy based on a tandem-type mass spectrometer, where they were produced by passing Ni3,4+ through methanol vapor under a multiple collision condition. The IR-PD spectra were measured in the wavenumber region between 3100 and 3900 cm-1. In each IR-PD spectrum, a single peak was observed at a wavenumber lower by approximately 40 cm-1 than that of the OH stretching vibration of a free methanol molecule and was assigned to the OH stretching vibrations of the methanol molecules in Ni3,4+ (CH3OH)m. The photodissociation was analyzed by assuming that Ni3,4+ (CH3OH)m dissociate unimolecularly after the photon energy absorbed by them is statistically distributed among the accessible modes of Ni3,4+ (CH3OH)m. In comparison with the calculations performed by the density functional theory, it is concluded that (1) the oxygen atom of each methanol molecule is bound to one of the nickel atoms in Ni3,4+ (defined as molecular chemisorption), (2) the methanol molecules in Ni3,4+ (CH3OH)m do not form any hydrogen bonds, and (3) the cross section for demethanation [CH4 detachment from Nin+ (CH3OH)] is related to the electron density distribution inside the methanol molecule.     

Ni-B非晶态合金电极上乙醇的电氧化及其动力学参数的测定

应用循环伏安法研究了碱性介质中Ni-B非晶态合金纳米粉末微电极和化学镀Ni-B非晶态合金微盘电极上乙醇的电催化氧化. 结果表明, Ni-B非晶态合金纳米粉末微电极和化学镀Ni-B非晶态合金微盘电极对碱性溶液中乙醇的氧化均具有很高的电催化作用, 且前者的电催化氧化活性高于后者. 运用稳态极化曲线测定了Ni-B非晶态合金纳米粉末微电极上乙醇的电催化氧化动力学参数. 与高择优取向(220)镍电极比较, 碱性介质中Ni-B非晶态合金纳米粉末微电极上乙醇的电催化氧化速率显著提高. 采用循环伏安法测定的Ni-B非晶态合金纳米粉末微电极上Ni(OH)2的质子扩散系数高出文献报道的镍纳米线电极和表面化学镀Co的球形Ni(OH)2粉末电极约2个数量级.     

Effect of pH on the synthesis and properties of luminescent SiO2/calcium phosphate:Eu3+ core-shell nanoparticles

A novel method for the synthesis of luminescent SiO(2)/calcium phosphate (CaP):Eu(3+) core-shell nanoparticles (NPs) was developed via a sol-gel route followed by annealing at a temperature of 800 °C. The object of this study was the investigation of the effect of pH on the formation of a CaP shell around the silica core. The resulting annealed NPs exhibited an amorphous SiO(2) core and a crystalline luminescent shell. The formation of a CaP layer was possible at pH below 4.5 and above 6.5 during the coating step. The crystal structure of the shell was studied by X-ray diffraction analysis. Hydroxyapatite (HAp) and α-tricalcium phosphate were detected as crystal phases of the surrounding layer. However, NPs produced under basic conditions exhibited a higher crystallinity of the CaP layer than did samples coated at pH below 4.5. In the pH interval between 4.5 and 6.5, no shell growth but the formation of secondary NPs containing CaO and Ca(OH)(2) was observed. Furthermore, SiO(2)/CP:Eu(3+) core-shell NPs were investigated by transmission electron microscopy, dynamic light scattering, Fourier transform infrared spectroscopy, inductively coupled plasma optical emission spectrometry, and photoluminescence spectroscopy. The resulting HAp-coated NPs were successfully tested by a cell-culture-based viability assay with respect to a later application as a luminescent marker for biomedical applications.