On the Coexistence of Chemically Similar Stable and Metastable Phases in the BeO–MgO–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> System

The joint crystallization of the stable phase (a number of solid solutions of chromium-containing beryllian indialite) and metastable phases (crystalline modifications) of the compound with β-quartz structure (Si_0.64Al_0.28Mg_0.21Be_0.09)^IVO₂ ~ Mg_1.89Be_0.81Al_2.52Si_5.76O₁₈ admixed with Cr₂O₃ phases of khmaralite Mg_1.21Cr_0.01Be_0.46Al_1.78Si_3.38O₂₀ and spinel {(Mg_0.95Be_0.045Si_0.005)^IV(Al_1.31Cr_0.67Mg_0.02)^VI}O₄ is performed using melted chromium–beryllian indialite preliminarily obtained by solid-phase synthesis as a precursor. Simultaneously, the residual X-ray amorphous melt of composition Mg_1.83Cr_0.01Be_1.04Al_2.64Si_5.57O₁₈ is hardened. Thus, a reconstructive transition from the beryllian indialite melt to a phase with the β-quartz structure is implemented, and the chemical similarity of these compounds is demonstrated. The rate of change in the crystallization isotherm of 2°С/h and increased heat outflow through the highly heat-conducting walls of the Pt–Rh crucible (taper) contribute to this process.     

Study of the KNO<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> system by differential scanning calorimetry

The structural and the thermodynamic properties of potassium nitrate KNO₃ and its composites with nanosized aluminum oxide Al₂O₃ have been studied by differential scanning calorimetry. It has been found that an amorphous phase forms in composites (1–x)KNO_3–xAl₂O₃. The thermal effect corresponding to this phase has been observed at 316°C. It has been found that the phase transition heats of potassium nitrate decreased as the aluminum oxide fraction increased.     

Magnetic and magnetoresistive properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–Sr<Subscript>2</Subscript>FeMoO<Subscript>6–δ</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoheterostructures

A method has been developed for fabricating nanoporous matrices based on anodic aluminum oxide for the deposition of ferromagnetic nanoparticles in them. The modes of deposition of strontium ferromolybdate thin films prepared by the ion-plasma method have been worked out, and the magnetic and magnetoresistive properties, structure, and composition of the films have been investigated. It has been revealed that the microstructure and properties of the strontium ferromolybdate films deposited by ionplasma sputtering depend on the deposition rate and the temperature of the substrate. Based on the measurement of the electrical resistivity of nanoheterostructures in a magnetic field, it has been found that the magnetoresistance reaches 14% at T = 15 K and B = 8 T, which is due to the manifestation of tunneling magnetoresistance.     

Phase formation in the BaCO<Subscript>3</Subscript>–PbO–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>–Nb<Subscript>2</Subscript>O<Subscript>5</Subscript> system

Features of the formation of lead-ferroniobate compounds in the xBaCO₃–(1 – x)PbO–Fe₂O₃–Nb₂O₅ system by solid-phase synthesis are investigated. For perovskite-type lead-ferroniobate solid solution, a single-phase concentration region is revealed at 1233 K. The crystalline structures of the synthesized compounds are refined using Rietveld analysis and the Pm3?m and R3m space groups. Ceramic samples of lead ferroniobate are studied by scanning electron microscopy.     

White,green, and yellow photoluminescence in the (CaO · Al<Subscript>2</Subscript>O<Subscript>3</Subscript> · SiO<Subscript>2</Subscript>): Eu system

It is shown that nitrogen-laser excited (2CaO · m(Al₂O₃) · SiO₂): Eu photoluminescent phosphors obtained by direct solid-state synthesis at 1350°C emit white, green, and yellow lights when Al₂O₃ content m in the system decreases from 0.40 to 0.05. The coordinates of these colors correspond to the coordinates of light warning systems according to International Commission on Illumination (CIE) and are close to the coordinates of primary colors in the EBU and NTSC TV standards.     

Electrical switching in the MoO<Subscript>3</Subscript>–WO<Subscript>3</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript> and MoO<Subscript>3</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript> glasses

High field electrical switching on blown films of MoO₃(60%)–P₂O₅(40%), MoO₃(50%)–WO₃(10%)–P₂O₅(40%), and MoO₃(45%)–WO₃(15%)–P₂O₅(40%) having different thicknesses was studied and compared. Switching was observed using two terminal samples. S-type current–voltage characteristic (current-controlled negative resistance—CCNR) with memory was observed in molybdenum–phosphate glasses, but N-type characteristic (voltage-controlled negative resistance—VCNR) with threshold in tungsten–molybdenum–phosphate glasses was observed. The important observation was that with the addition of WO₃ to binary MoO₃–P₂O5 led to a change of I–V characteristic from CCNR with memory to VCNR with threshold. The measurements of density and molar volume showed linear relation between MoO₃ content and density which decreased with the increase of MoO₃ content. The samples’ thickness had no significant effect on threshold voltage. The attained results also indicated that the electrode material had no effect on switching property of devices. The switching behavior of the devices did not show any dependence on the polarity of the applied voltage. In terms of the effect of heat on the switching behavior of molybdenum–phosphate glasses, it was found that threshold voltage decreases with increasing of temperature. Finally, the switching phenomenon was explained by thermal (formation of crystalline filaments) and electronic models.     

Sol–gel synthesis and characterization of Li<Subscript>2</Subscript>CO<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composite solid electrolytes

Composite solid electrolytes in the system (1???x)Li₂CO₃–xAl₂O₃, with x?=?0.0–0.5 (mole), were synthesized by a sol–gel method. The synthesis carried out at low temperature resulted in voluminous and fluffy products. The obtained materials were characterized by X-ray diffraction, differential scanning calorimetry, scanning electron microscopy/energy-dispersive X-ray, Fourier transform infrared spectroscopy and AC impedance spectroscopy. Structural analysis of the samples showed an amorphous feature of Li₂CO₃ and traces of α-LiAlO₂, γ-LiAlO₂ and LiAl₅O₈. The prepared composite samples possess high ionic conductivities at 130–180 °C on account of the presence of lithium aluminates as well as the formation of a high concentration of an amorphous phase of Li₂CO₃ via this sol–gel preparative technique.     

Anomalous nuclear spin–lattice relaxation of <Superscript>3</Superscript>Не in contact with ordered Al<Subscript>2</Subscript>O<Subscript>3</Subscript> aerogel

Spin–lattice relaxation of ³Не in contact with the ordered Al₂O₃ fiber aerogel has been studied at the temperature of 1.6 K in fields of 0.1–0.5 T by the pulsed nuclear magnetic resonance (NMR) method. An additional mechanism of the relaxation of ³Не in aerogels is found and it is shown that this relaxation mechanism is not associated with the adsorbed layer. A hypothesis about the influence of intrinsic paramagnetic centers on the relaxation of gaseous ³Не is proposed.     

Effect of mixed glass formers on the crystallization kinetics in AgI–Ag<Subscript>2</Subscript>O–V<Subscript>2</Subscript>O<Subscript>5</Subscript>–MoO<Subscript>3</Subscript> glassy superionic system

The crystallization and glass transition kinetics using differential scanning calorimetry (DSC) in 50AgI–33.33Ag₂O–16.67[(V₂O₅)_1−x –(MoO₃) _x ] superionic glassy system is discussed. Thermal stability of glass, studied using various criteria, does not vary significantly with glass former variation. However, the activation energies for structural relaxation (E _s) at glass transition temperature and crystallization (E _c) obtained using Moynihan and Kissinger, Matusita-Sakka formulations found to exhibit interesting trends with MoO₃ substitution in the glass matrix. It is noticed that the electrical conductivity (σ)–temperature (T) cycles obtained at a typical heating rate of 1 °C/min do exhibit significant thermal events. The conductivity after first heating cycle at room temperature is found to be increasing with MoO₃ content and maximum for x = 0.3 (~10⁻³ Ω⁻¹ cm⁻¹ at 30 °C) which is comparable to that of the host 50AgI–33.33Ag₂O–16.67V₂O₅ glassy system. The parameters obtained from σ–T plots and DSC scans do complement each other in a particular range of composition.     

Elastic properties of TeO<Subscript>2</Subscript>–B<Subscript>2</Subscript>O<Subscript>3</Subscript>–Ag<Subscript>2</Subscript>O glasses

A series of glasses [(TeO₂) _x (B₂O₃)_1−x ]_1−y [Ag₂O] _y with x = 70 and y = 10, 15, 20, 25 and 30 mol% were synthesised by rapid quenching. Longitudinal and shear ultrasonic velocity were measured at room temperature and at 5 MHz frequency. Elastic properties, Poisson's ratio, microhardness, softening temperature and Debye temperature have been calculated from the measured density and ultrasonic velocity at room temperature. The experimental results indicate that the elastic constants depend upon the composition of the glasses and the role of the Ag₂O inside the glass network is discussed. Estimated parameters based on Makishima–Mackenzie theory and bond compression model were calculated in order to analyse the experimental elastic moduli. Comparison between the experimental elastic moduli data obtained in the study and the calculated theoretically by the mentioned above models has been discussed.     

Facile synthesis of nanosized ε-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> particles on the silica support

An approach is suggested to synthesize the ε-Fe₂O₃ particles supported on silica with the mean size of few nanometers, narrow size distribution and no admixture of any other iron oxide polymorphs. The facile synthesis is based on the pore filling impregnation method by iron sulfate (II) water solution with the following annealing procedure at ~1173 K. It is shown that the ε-Fe₂O₃ nanoparticles obtained are stable up to ~1173 K and possess superparamagnetic behavior up to ~870 K.     

Dielectric response of SrTiO<Subscript>3</Subscript>–SrMg<Subscript>1/3</Subscript>Nb<Subscript>2/3</Subscript>O<Subscript>3</Subscript> solid solutions in the terahertz–infrared range

The reflection and transmission spectra of ceramic samples of SrTiO₃–SrMg_1/3Nb_2/3O₃ solid solutions have been measured in the frequency range of 5–5000 cm^–1 and in the temperature range of 5–370 K. Based on these spectra, the spectra of the real ε'(ν) and imaginary ε''(ν) parts of the complex permittivity ε*(ν) have been simulated by the method of dispersion analysis. It has been found that the temperature evolution of the dielectric constant is entirely determined by the behavior of the soft mode.     

Luminescence centers in α-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> ceramics

Luminescence photoexcitation spectra of α-Bi₂O₃ ceramics are investigated. Luminescence spectra were deconvoluted into fundamental components using the Alentsev-Fok method. It is established that the luminescence spectra of α-Bi₂O₃ ceramics consist of three fundamental bands with maxima at 2.75, 2.40, and 1.97 eV. A comparison of the results with those from an investigation of luminescence of various modifications of bismuth oxide and bismuth germanates suggests that luminescence of these compounds is caused by radiation processes that occur in structural complexes that contain the bismuth ion in a nearest oxygen environment. Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 75, No. 5, pp. 672–676, September–October, 2008.     

AC Conductivity,XRD and transport properties of melt quenched PbI<Subscript>2</Subscript>–Ag<Subscript>2</Subscript>O–Cr<Subscript>2</Subscript>O<Subscript>3</Subscript> system

Composite materials used for electrode and electrolyte materials have been intensely studied in view of their advantages such as higher conductivity and better operational performance compared to their single-phase counterparts. The present work aims at studying the electrical and structural characteristics of a new composite electrolyte namely, (PbI₂) _x  − (Ag₂O–Cr₂O₃)_100−x where x = 5, 10, 15, 20, and 25 mol%, respectively, prepared by the melt quenching technique. The room temperature X-ray diffraction spectra revealed certain crystalline phases in the samples. AC conductivity analysis for all the prepared samples was carried out over the frequency range 1 MHz–20 Hz and in the temperature window 297–468 K. The room temperature conductivity values were calculated to be in the order of 10⁻⁵–10⁻³ Scm⁻¹. An Arrhenius dependence of temperature with conductivity was observed, and the activation energies calculated were found to be in the range 0.27–0.31 eV. Furthermore, the total ionic transport number (t _i) values obtained for all these indicated the ionic nature of this system. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, Dec. 7–9, 2006.     

Investigation on the effects of addition of SiO<Subscript>2</Subscript> nanoparticles on ionic conductivity,FTIR, and thermal properties of nanocomposite PMMA–LiCF<Subscript>3</Subscript>SO<Subscript>3</Subscript>–SiO<Subscript>2</Subscript>

Composite polymer electrolyte systems composed of poly(methyl methacrylate) (PMMA) as the host polymer, lithium trifluoromethanesulphonate (also known as lithium triflate; LiCF₃SO₃) as dopant salt, and a variety of different concentrations of nano-sized fumed silica (SiO₂) as inorganic filler were studied. The effect upon addition of SiO₂ on the ionic conductivity of the composite polymer electrolytes was investigated, and it was proven that the ionic conductivity had been enhanced. In addition, the interfacial stability also showed improvement. Maximum conductivity was obtained upon addition of 2 wt.% SiO₂. The complexation of PMMA and LiCF₃SO₃ was verified through Fourier transform infrared studies. The thermal stability of the polymer electrolytes was also found to improve after dispersion of inorganic filler. This was proven in the thermogravimetric studies.     

Influence of Matrix Nature on the Structural Characteristics of In<Subscript>2</Subscript>O<Subscript>3</Subscript>–CeO<Subscript>2</Subscript> and SnO<Subscript>2</Subscript>–CeO<Subscript>2</Subscript> Composites Fabricated by the Impregnation Method

The structural characteristics, valence states, and distribution of cerium ions between the components in In₂O₃–CeO₂ and SnO₂–CeO₂ nanocomposites fabricated using the impregnation method were studied. X-ray photoelectron spectroscopy (XPS) and energy-dispersive X-ray spectroscopy (EDX) were used to show that, during impregnation, cerium ions are not included into In₂O₃ crystals and are disposed only on their surface in the form of nano-sized crystallites or amorphous clusters. On the other side, under the contact of CeO₂ clusters with a surface of SnO₂ matrix crystals, cerium ions penetrate into the surface layer of these crystals. In contrast to an In₂O₃–CeO₂ system, where the addition of CeO₂ does not affect the conduction activation energy, where cerium oxide is added to SnO₂, the observed increase in the resistance of a SnO₂–CeO₂ composite is accompanied by a sufficient increase in activation energy. These data and the XPS spectra confirm the modification of the surface layers of conductive SnO₂ crystals as, a result of the penetration of cerium ions into these layers.     

Production of ultrafine particles of high-temperature tetragonal WO<Subscript>3</Subscript> by dc arc discharge in Ar–O<Subscript>2</Subscript> gases

Ultrafine particles of WO₃ are successfully produced by dc arc discharge in Ar-O₂ gases. Particle sizes are distributed from 10 nm to 1 m depending on production conditions: gas pressure, collection position and discharge current. Observations of the cooled particles by electron microscopy indicate that the WO₃ particles are tetragonal, a phase that is usually only stable above 725 °C. The octahedral crystals are bounded by eight {1 0 1} faces and occasionally truncated by {1 0 0} and/or {0 0 1} faces. This method of producing WO₃ by dc arc discharge therefore affords a high-temperature phase that is preserved upon cooling to room temperature.     

High-Temperature Heat Capacity of Zn<Subscript>2</Subscript>V<Subscript>2</Subscript>O<Subscript>7</Subscript>–Cu<Subscript>2</Subscript>V<Subscript>2</Subscript>O<Subscript>7</Subscript> Solid Solutions

Differential scanning calorimetry has been used to study the influence of temperature on the heat capacity of synthesized vanadates Zn₂V₂O₇, (Cu_0.56Zn_1.44)V₂O₇, and (Cu_1.0Zn_1.0)V₂O₇. It is found that dependences C_p = f(T) have extremes. The thermodynamic properties of Zn₂V₂O₇ have been determined.     

Dielectric relaxation in magnetoelectric composite 0.85BiFeO<Subscript>3</Subscript>–0.15MgFe<Subscript>2</Subscript>O<Subscript>4</Subscript>

Dielectric properties of 0.85BiFeO₃–0.15MgFe₂O₄ composite fabricated with conventional ceramic technology are studied in the temperature interval of 20–250°C at frequencies of 25 Hz to 1 MHz. Dielectric relaxation is observed, the nature of which is discussed in the context of a mechanism of interaction between ferroelectric domain boundaries and point defects.