一种辐射零点可控的紧凑型滤波贴片天线

提出了一种辐射零点可控的紧凑型滤波贴片天线。该滤波天线以基本的微带贴片天线为原型,主要由一个简单的金属辐射贴片和两个对称的分割形槽组成。两个分割形槽蚀刻在金属贴片上,使得高/低频段分别产生两个宽边辐射零点,从而引入滤波选频功能。该结构未引入额外滤波电路和其他寄生单元,节省了空间尺寸,结构更加紧凑;两个辐射零点独立可控,提高了设计的灵活度。且在实现滤波选频功能的同时,对天线增益的影响很小。利用HFSS仿真软件优化滤波天线结构,制作了一个实物模型并进行了测试。测试结果与仿真结果基本一致。测试结果表明,提出的滤波天线工作在2.40 GHz,两个独立可控的辐射零点分别位于1.96 GHz和2.66 GHz,平均实际增益约为7.0 dBi,带外抑制水平超过39 dB。     

基于缺陷接地结构的太赫兹双频微带天线

提出了一种工作在太赫兹频段的双频微带天线。在普通矩形微带天线的基础上,在辐射贴片上加载45°和135°的矩形贴片增大辐射面积,增大高频谐振点处阻抗带宽。通过引入缺陷接地结构使得天线在接地板处的电流路径改变,并与辐射贴片相互耦合,从而实现双频特性。为提高天线增益,在辐射贴片边缘加载若干寄生矩形贴片,并增加了寄生贴片处的基板厚度。该款天线可以同时在520 GHz(508~532 GHz)和680 GHz(581~766 GHz)的频段下工作,其中高频段的相对带宽达到了27.5%,最大增益达到了3.54 dB和4.11 dB。该双频天线结构相对简单,各项性能指标稳定,对于工作在太赫兹频段上的通信系统和无线传输系统具有一定的应用价值。     

Compact superconducting single-and dual-band filter design using multimode stepped-impedance resonator

This study presents two multimode stepped-impedance structures to design single-and dual-band filters. Transmission zeroes are introduced for the single-band filter by using dual-mode stepped-impedance resonators. The single-band filter with high selectivity is centered at 6.02 GHz and has a fractional bandwidth(FBW) of 25.6%. Four stubs(two low frequency and two high frequency ones) are connected to the rectangular patch in the center to construct a quadruplemode resonator. The independent conditions of the center frequencies of the high and low bands of the resonator are analyzed. A dual-band filter, which operates at 1.53 GHz and 2.44 GHz with FWBs of 12.1% and 14.1%, respectively is designed. The single-and dual-band filters are both fabricated with double-sided YBCO films and they can be used in mobile and satellite communications.     

一种光激发可切换的双频太赫兹超材料吸收器

提出了一种基于方环-金属线结构的光激发动态可切换双频太赫兹超材料吸收器。通过调节嵌入在结构间隙中的光敏硅和锗的绝缘/导通状态,该吸收器可在不改变结构的前提下在三个双频完美吸收态之间自由切换。结果表明:当没有光泵浦时,该吸收器工作在0.987 THz和1.767 THz双频吸收态;当采用800 nm激光泵浦时,该吸收器可切换为0.717 THz和1.444 THz处的双频吸收;当采用1550 nm激光泵浦时,该吸收器的吸收状态可切换为0.716 THz和1.767 THz处的双频吸收。本文从等效电路、匹配阻抗和电流分布三方面解释了三种可切换的双频吸收机制,并讨论了极化不敏感的吸收特性。     

Design and implementation of dual-band antennas based on a complementary split ring resonators

A simple dual-band antenna design and implementation method is proposed in this work, based on the equivalent media properties inspired by resonant metamaterial elements. The equivalent circuit model of dual-band patch antennas based on a complementary split ring resonator (CSRR) is presented and validated. The dual-band patch antenna is designed etching a CSRR in the patch of a conventional rectangular microstrip patch antenna. The first resonance is governed by the quasi-static resonance of the CSRR while the second resonance is originated by the rectangular patch. The fact of etching a CSRR on a rectangular patch antenna also produces a miniaturization of a conventional patch antenna. The equivalent circuit model proposed in this letter is sound in order to understand the functionality of dual-band patch antennas based on a CSRR. Good agreement between simulation, equivalent circuit model and experimental results is shown and discussed. These results lead the equivalent circuit model to become a simple and straightforward tool for the design of this type of multiband antennas, of low cost and versatile operation for a broad range of wireless communication systems.     

Dual-band wearable antenna using split ring resonator

Abstract

This paper presents dual-band wearable antenna using split-ring resonator (SRR). The SRR is placed near patch and feed line. SRR makes a major contribution to the first operating band (2.32 GHz), but it has a minor effect on the second operating band (3.5 GHz). The wearable antenna at 3.5 GHz (without using SRR) is also presented for comparison sake. The simulation results are analyzed and compared with the measured results, which shows that there is a good agreement between them.     

Electromagnetic coupling reduction in dual-band microstrip antenna array using ultra-compact single-negative electric metamaterials for MIMO application

In this paper, an ultra-compact single negative(SNG) electric waveguided metamaterial(WG-MTM) is first investigated and used to reduce the mutual coupling in E H planes of a dual-band microstrip antenna array. The proposed SNG electric WG-MTM unit cell is designed by etching two different symmetrical spiral lines on the ground, and has two stopbands operating at 1.86 GHz and 2.40 GHz. The circuit size is very compact, which is only λ_0/33.6 ×λ_0/15.1(where λ_0 is the wavelength at 1.86 GHz in free space). Taking advantage of the dual-stopband property of the proposed SNG electric WG-MTM, a dual-band microstrip antenna array operating at 1.86 GHz and 2.40 GHz with very low mutual coupling is designed by embedding a cross shaped array of the proposed SNG electric WG-MTM. The measured and simulated results of the designed dual-band antenna array are in good agreement with each other, indicating that the mutual coupling of the fabricated dual-band antenna array realizes 9.8/11.1 d B reductions in the H plane, 8.5/7.9 d B reductions in the E plane at1.86 GHz and 2.40 GHz, respectively. Besides, the distance of the antenna elements in the array is only 0.35 λ_0(where λ_0 is the wavelength at 1.86 GHz in free space). The proposed strategy is used for the first time to reduce the mutual coupling in E H planes of the dual-band microstrip antenna array by using ultra-compact SNG electric WG-MTM.     

Single-layer dual-band terahertz filter with weak coupling between two neighboring cross slots

A dual-band terahertz(THz) filter consisting of two different cross slots is designed and fabricated in a single molybdenum layer. Experimental verification by THz time-domain spectroscopy indicates good agreement with the simulation results. Owing to the weak coupling between the two neighboring cross slots in the unit cell, good selectivity performance can be easily achieved, both in the lower and higher bands, by tuning the dimensions of the two crosses. The physical mechanisms of the dual-band resonant are clarified by using three differently configured filters and electric field distribution diagrams. Owing to the rotational symmetry of the cross-shaped filter, the radiation at normal incidence is insensitive to polarization. Compared with the THz dual-band filters that were reported earlier, these filters also have the advantages of easy fabrication and low cost, which would find applications in dual-band sensors, THz communication systems, and emerging THz technologies.     

基于正六边形多开口的新型双频带左手材料

本文提出了基于正六边形多开口的新型双频带磁谐振体.在微波衬底材料的一面放置交错多开口的两个正六边形金属环,多开口结构破坏了环间耦合电容,从而使两环形成相对独立的两个谐振网络实现双频带效应.最后将该谐振结构的另一面放置金属导线形成一个双频带的新型左手材料.文中利用HFSS软件仿真和等效参数提取的方法,分析和验证该结构的正确性.     

Multifrequency super-thin cloaks

Bandwidth and thickness have become the most troublesome problems for EM cloaks. In this paper, we propose to solve the two problems using connected patches based on the microwave network model. By covering an obstacle with combined connected patches, cloaking effect can be achieved at multiple frequencies so as to expand the operating band. As an explicit example, a dual-band super-thin cloak using two different connected patch unit cells is demonstrated. Cloaking effect can be achieved at 3.50 GHz and 4.14 GHz simultaneously with an 8 dB transmission enhancement. The cloak design method provides a new route to broadening the bandwidth of thin EM cloaks.     

Single-/dual-band metamaterial absorber based on cross-circular-loop resonator with shorted stubs

A single-/dual-band metamaterial absorber (MMA) based on cross-circular-loop resonator (CCLR) with shorted stubs is discussed at microwave frequencies in this paper. The single-/dual-band characteristics are realized by adjusting the positions of the shorted stubs. We briefly analyze the equivalent circuit model of the MMA unit cell and then numerically and experimentally investigate the near-perfect absorptions in such two conditions (single- and dual-band). The results indicate that the proposed MMA exhibits near-perfect impedance matching with free space and high absorptivity of 99.74?% at 8.65?GHz for single-band condition, and absorptivities of 99.75?% and 97.35?% at 8.525 and 9.1?GHz, respectively, for dual-band condition. It also exhibits a wide range of angles of incidence for both transverse electric (TE) and transverse magnetic (TM) radiation. The two operating frequency bands, in dual-band condition, can be further controlled by adjusting the positions of shorted stubs or adding other shorted stubs. So it opens the way to fabricate controllable MMAs, and so controllable perfectly matched layers and bolometers.     

Dual-band isotropic metamaterial absorber based on near-field interaction in the Ku band

We numerically and experimentally investigate single-band and dual-band isotropic metamaterial absorbers (IMAs) based on metallic disks. By optimizing the diameter of the metallic disks and the thickness of the dielectric substrate, the single-band IMA is observed at 16.2 GHz with absorptivity of 97%. When adding one disk-pair to the structure, the dual-band IMA is obtained at 12.8 and 15.5 GHz due to the symmetry breaking. The physical mechanics is explained by near-field coupling effect and equivalent LC circuit model. The measurement results performed in the range 12–18 GHz show a good agreement with simulation and theoretical analysis. Our findings demonstrate a new approach to achieve dual-band and multi-band IMAs.     

Dual-band frequency selective surface with quasi-elliptic bandpass response

Based on the substrate integrated waveguide technology,we present a dual-band frequency selective surface(FSS) with a quasi-elliptic bandpass response.The characteristics of the quasi-elliptic bandpass response are realized by shunting two substrate integrated waveguide cavities of different sizes,with the same slots on both sides of the metal surfaces.Four cavities of different sizes and two slots of different sizes are used to design the novel FSS.Every bandpass response with sharp sidebands is induced by two transmission nulls that are generated by the coupling between the slot aperture resonance and the cavity resonance.The simulation results show that such dual-band FSS has the advantages of high selectivity and stable performance at different oblique incident angles.Moreover,it is easy to fabricate.     

基于发卡式开口谐振环的柔性双频带超材料

本文设计了一种基于开口谐振环(split ring resonator, SRR)混合排列单元格的小型化双频带超材料(metamaterial, MM). 该MM的单元结构为发卡式SRR, 所设计的双频带MM可以应用于无线局域网(2.4 GHz) 和全球微波互联接入(3.5GHz)系统. 并且, 采用柔性介质作为基板增加了MM的柔韧度和普适性, 实验和测试结果表明: 双频带MM的中心频率可以通过调节SRR的尺寸进行控制. 此外, 本文也对MM在不同入射角的情况进行了分析, 结果表明MM对入射角度不敏感.最后, 通过MM的表面电流分布情况研究, 进一步解释了其双频带谐振频率的产生原理.     

Novel 53/106 GHz Dual-Band MMW LC Oscillator Implemented in SiGe BiCMOS Technology

In this Paper, we present a fully integrated millimeter wave LC voltage-controlled oscillator (VCO), which employs a novel topology, operating at dual-band frequency of 53.22 GHz-band and 106.44 GHz-band. The low-phase noise performance of –107.3 dBc/Hz and –106.1 dBc/Hz at the offset frequency of 600 kHz, –111.8 dBc/Hz and –110.6 dBc/Hz at the offset frequency of 1 MHz around 53.22 GHz and 106.44 GHz are achieved using IBM BiCMOS-6HP technology, respectively. Two tuning ranges, of 52.7 - 53.8 GHz and 105.4 - 107.6 GHz for the proposed LC VCO are obtained. The output voltage swing of this VCO is around 1.8 V_p-p at the operation frequency of 53.22 GHz and 0.45 V_p-p at 106.44 GHz; the total power consumption is about 16.5 mW. To our knowledge, this is the first oscillator which operates at dual-band frequency above 50 GHz with the best preformance.     

An ultra-thin dual-band wide-angle polarization-insensitive metamaterial absorber with near-unity absorbance

In this paper, a dual-band metamaterial absorber (MMA) with wide-angle and polarization-insensitivity is proposed. The MMA consists of two copper layers with a layer of FR-4 between them. And its top layer consists of a cross-shaped resonator and a square ring resonator. The calculation result demonstrates that there are two distinct absorption peaks, whose absorptivity are 99.933% at 3.8441 GHz and 99.99% at 9.1094 GHz. And its thickness is only 1.34% of the wavelength of the lowest absorption frequency. The dual-band MMA shows polarization-insensitivity for normal incident wave and shows high absorptivity in a wide incident angle for both TE and TM polarization wave. In addition, we discuss the working mechanism. The influences of main parameters on the dual-band MMA's absorption are also analyzed. The proposed ultra-thin MMA has simple structure and high absorptivity, which has many potential applications, such as thermal radiometer, detection sensor, stealth technology.     

A dual-band polarization insensitive metamaterial absorber with split ring resonator

A dual-band polarization insensitive absorber has been proposed . Unlike the previous dual band absorber composed of composite structures, only one square metal ring with a slit at the middle of each side can be used to achieve the dual-band absorption. The calculated results show two distinct absorption peaks of 0.96 at 10 GHz and 0.99 at 20 GHz. In addition, the positions of the two peaks are strongly influenced by the width of the slit (g). More importantly, the absorptions of the two peaks keep higher than 0.9 while g changing. The dual-band absorber may have many potential applications in scientific and technological areas because of its excellent absorption characteristics and concise structure.     

Dual-band tunable negative refractive index metamaterial with F-Shape structure

This paper presents a negative refractive index tunable metamaterial based on F-Shape structure which is capable of achieving dual-band negative permeability and permittivity, thus dual-band negative refractive index. An electromagnetic simulation was performed and effective media parameters were retrieved. Numerical investigations show clear existence of two frequency bands in which permeability and permittivity both are negative. The two negative refractive index bandwidths are from 23.8 GHz to 24.1 GHz and from 28.3 GHz to 34.9 GHz, respectively. The geometry of the structure is simple so it can easily be fabricated. The proposed structure can be used in multiband and broad band devices, as the band range in second negative refractive index region is 7 GHz, for potential applications instead of using complex geometric structures and easily tuned by varying the separation between the horizontal wires.     

具有高隔离度的双陷波超宽带多入多出天线

提出了一款具有高隔离度的双陷波超宽带多入多出(UWB MIMO)天线。该天线由两个相同的半切超宽带天线单元倒置构成。通过在天线底板刻蚀栅栏型缺陷地解耦结构,使该MIMO天线的隔离度提高至25 dB。此外,在天线半圆形辐射贴片上刻蚀两个方向相反的"L"型缝隙,实现了双陷波的功能,分别抑制了802.16无线城域网WiMAX(3.2~3.7 GHz)和WLAN(5.15~5.85 GHz)信号对天线系统的干扰。实验结果表明,该天线在3~11 GHz工作带宽内的隔离度大于25 dB,包络相关系数(ECC)小于0.004;第一个陷波频段为3.0~3.7 GHz,第二个陷波频段为5.1~5.85 GHz,有效抑制了WiMAX和WLAN的信号干扰。