4,4'-二羟基二苯硫醚对聚甲醛结晶和熔融行为的影响

为了探究4,4'-二羟基二苯硫醚(TDP)的添加对聚甲醛(POM)熔融与结晶行为的影响,本文利用熔融共混的方法制备了POM/TDP共混材料。通过差示扫描量热仪(DSC)对共混材料的熔融与结晶行为进行了研究,利用广角X射线衍射仪(WAXD)对共混材料的晶体结构进行了研究。结果表明,在POM中添加TDP后,POM的晶面间距变大,晶体结构变的疏松,使POM的结晶温度(Tc)、结晶焓(ΔHc)、熔融温度(Tm)与熔融焓(ΔHm)均降低。当TDP质量分数增加到30%时,共混物的熔点与结晶温度较纯POM分别下降了15.2和12.8℃。在等温结晶过程中,随着TDP含量的增大,POM完成结晶所需的时间显著加长,共混物的结晶速率逐渐降低,结晶活化能逐渐升高,但TDP的加入对POM的晶型并没有影响。以上结果说明TDP的添加对POM的熔融与结晶行为影响很大,这将为POM结晶行为的调控提供依据。     

聚(L-丙交酯)/聚(DL-丙交酯)的结晶性能及相溶性

用共溶液沉淀法制备了聚 (L 丙交酯 ) 聚 (DL 丙交酯 )共混物 (PLLA PDLLA) ,然后用成纤模压法压制成3 2mm的棒材 .用差示扫描量热法研究了共混物的结晶性能和相溶性 .结果表明 ,PLLA组分在共溶液沉淀过程中可生成结晶 ,共混物中PDLLA含量直到 30 %时 ,PLLA组分的结晶熔融温度和结晶度与纯PLLA相同 ,但PDLLA含量为 5 0 %时 ,PLLA组分的结晶熔融温度和结晶度明显下降 .由于加工成型条件的不一致性 ,共混物棒材中的PLLA组分的结晶熔融温度和结晶度呈较大的分散性 .共混物从熔体降温 ,在其后的升温DSC扫描中出现分别相应于PDLLA和PLLA的玻璃化转变 ,表明PDLLA与未结晶的PLLA形成的非晶相是不相溶的     

聚左旋乳酸/聚氧化乙烯共混物的拉伸行为及结构转变

采用熔融共混方法制备了聚左旋乳酸(PLLA)和超高分子量聚氧化乙烯(PEO)共混物, 通过差示扫描量热(DSC)、 扫描电子显微镜(SEM)和二维广角X射线散射(2D-WAXS)等方法系统研究了PEO的加入对不同温度下PLLA拉伸行为及拉伸过程中微观结构变化的影响. 结果表明, PLLA/PEO共混物为非均相体系, PEO粒子均匀分布在PLLA中形成两相结构. PEO的加入能够显著降低PLLA的玻璃化转变温度(T_g), 在25～60 ℃范围内显著提高PLLA的拉伸性能. 在60 ℃拉伸时, PEO的加入提高了PLLA在拉伸过程中的结晶和形变能力. 在80 ℃拉伸时, 共混物的拉伸断裂伸长率下降, 但共混物的结晶速度仍高于纯PLLA样品.     

溶剂诱导的聚乳酸/聚乳酸衍生物共结晶行为

通过溶液浇铸法制备不同组分的左旋聚乳酸(PLLA)和聚(L-2-羟基-3-甲基丁酸)(PL-2H3MB)共混物.运用差示扫描量热仪(DSC)、偏光显微镜(POM)、广角X射线衍射(WAXD)和热重分析仪(TGA)分析共混物的结晶、熔融行为和热稳定性.通过观察到DSC加热曲线中新的熔融峰判断PLLA和PL-2H3MB共晶...     

聚左旋乳酸/聚消旋乳酸共混物的结晶行为

非晶态聚消旋乳酸(PDLLA)对PLLA的结晶行为有较大的影响。本文利用差示扫描量热仪(DSC)和偏光显微镜(POM)对不同分子量PLLA、PDLLA按不同比例制得的共混物结晶进行了系统研究。结果表明随PDLLA含量的增大PLLA冷结晶温度升高,且越接近熔融温度。PDLLA分子量较小时PLLA球晶特征被明显破坏,PDLLA分子量较大时PLLA更易形保持球晶特征且易形成环带球晶形貌,这与结晶速率与非晶组分的扩散速率匹配程度有关。低分子量的PDLLA使PLLA的最大生长速率对应的温度出现在较低温度。     

多臂聚乳酸对线型聚乳酸结晶的促进作用

以多端羟基聚酯为引发剂,经丙交酯开环聚合得到多臂聚乳酸（MA-PLA）。 MA-PLA在DSC二次升温过程中,出现明显的冷结晶峰(41.5 J/g)和熔融峰(42.5 J/g),而工业产品聚乳酸PLLA 3051D没有这2个峰,确认该多臂聚乳酸的结晶能力优于3051D。 MA-PLA多臂聚乳酸的左旋乳酸单元含量为97%,高于3051D的91%。 将MA-PLA与PLLA-3051D共混后,在DSC二次升温过程中出现了熔融峰和冷结晶峰。 偏光显微镜观察表明,共混物的成核速率和初期球晶生长速度加快。 等温结晶动力学数据表明,110 ℃等温结晶的半结晶时间由空白样品的53.6 min缩短至共混物的31.7 min,Avrami指数n由空白样品的2.25增加至共混物的2.60,可见多臂聚乳酸对线形聚乳酸结晶性能的改善,主要是加快了成核速率。     

聚L-乳酸/聚(天冬氨酸-co-乳酸)共混物的制备及其相容性研究

采用氯仿/乙醇共沸溶液浇铸法制备了混合均匀的聚L-乳酸/聚(天冬氨酸-co-乳酸)共混物(PLLA/PAL)体系.研究了PLLA/PAL共混体系的热性能、结晶行为、形态结构和力学性能,评价了PLLA和PAL之间的相容性.结果表明,PAL对PLLA的结晶行为和热性能产生了较大的影响,共混物的结晶度较低,共混体系中部分PAL会进入PLLA球晶的片晶而导致PLLA球晶结构不完善,熔点降低.PAL的含量小于20%的PLLA/PAL共混物的拉伸强度和断裂延伸率均高于纯PLLA.PLLA和PAL分子链相互缠结,产生的氢键使分子链间存在较强的相互作用,具有较好的相容性.     

PTT/PET共混体系晶体形态与结晶性能的研究

用差示扫描量热仪(DSC)、广角X射线衍射(WAXD)和正交偏光显微镜研究了聚对苯二甲酸丙二酯(PTT)和聚对苯二甲酸乙二酯(PET)共混体系的晶体形态与结晶性能.结果表明,共混体系结晶性能与PTT的含量有关.PET的加入,使共混体系的球晶尺寸减小.球晶完善性降低.当PTT含量为40wt%～60wt%时,共混物分别出现了双重熔融峰和双重结晶峰.双重熔融峰是加热过程中熔融重结晶造成的,双重结晶峰说明不完善的晶体产生的次级结晶.     

尼龙1010结晶与熔融行为的研究

用DSC研究了降温速率R对尼龙10 10结晶与熔融的影响,以及室温(RT)和液氮(LN)骤冷退火样品的熔融.降温时结晶温度随R增大线性降低;T_g以上可完成结晶时结晶度相同;结晶起始温度>181℃生成的晶体有三个熔融峰,对应于环状和放射状球晶的转化与熔融;在181℃和T_g间结晶,无放射球晶转化峰;T_g下有结晶放热峰样品加热时有冷结晶发生.RT未退火样品三个熔融峰,退火温度T_α≥180℃样品两个峰,结晶度C∝T_a;LN未退火样品单一熔融峰,T_a>160℃双峰,T_a≤160℃三峰,低温峰温与C均∝T.     

聚左旋乳酸/聚消旋乳酸共混物的结晶行为

非晶态聚消旋乳酸(PDLLA)对聚左旋乳酸(PLLA)的结晶行为有较大的影响。本文利用差示扫描量热仪和偏光显微镜对不同分子量PLLA、PDLLA按不同比例制得的共混物结晶进行了研究。结果表明,随PDLLA含量的增大PLLA冷结晶温度升高,且越接近熔融温度。PDLLA分子量较小时PLLA球晶特征被明显破坏,PDLLA分子量较大时PLLA更易保持球晶特征且易形成环带球晶形貌,这与结晶速率与非晶组分的扩散速率匹配程度有关。低分子量的PDLLA使PLLA的最大生长速率对应的温度出现在较低温度。     

Preparation and characterization of biodegradable poly(l-lactide)/chitosan blends

In order to improve the properties of chitosan and obtain new fully biodegradable materials, blends of poly(l-lactide) (PLLA) and chitosan with different compositions were prepared by precipitating out PLLA/chitosan from acetic acid-DMSO mixtures with acetone. The blends were characterized by Fourier transform infrared analysis (FTIR), X-ray photoelectron spectroscopy (XPS), differential scanning calorimetry (DSC), ¹³C solid-state NMR and Wide-angle X-ray diffraction (WAXD). FTIR and XPS results showed that intermolecular hydrogen bonds existed between two components in the blends, and the hydrogen bonds were mainly between carbonyls of PLLA and amino groups of chitosan. The melting temperatures, cold crystallization temperatures and crystallinity of the PLLA component decreased with the increase in chitosan content. Blending chitosan with PLLA suppressed the crystallization of the PLLA component. Although the crystal structure of PLLA component was not changed, the crystallization of the blends was affected because of the existence of hydrogen bonds between two components, which was proved by WAXD results.     

Effects of carbon nanotubes on crystallization and melting behavior of poly(L‐lactide) via DSC and TMDSC studies

In this work, multiwalled carbon nanotubes (MWNTs) were surface‐modified and grafted with poly(L ‐lactide) to obtain poly(L ‐lactide)‐grafted MWNTs (i.e. MWNTs‐g‐PLLA). Films of the PLLA/MWNTs‐g‐PLLA nanocomposites were then prepared by a solution casting method to investigate the effects of the MWNTs‐g‐PLLA on nonisothermal and isothermal melt‐crystallizations of the PLLA matrix using DSC and TMDSC. DSC data found that MWNTs significantly enhanced the nonisothermal melt‐crystallization from the melt and the cold‐crystallization rates of PLLA on the subsequent heating. Temperature‐modulated differential scanning calorimetry (TMDSC) analysis on the quenched PLLA nanocomposites found that, in addition to an exothermic cold‐crystallization peak in the range of 80–120 °C, an exothermic peak in the range of 150–165 °C, attributed to recrystallization, appeared before the main melting peak in the total and nonreversing heat flow curves. The presence of the recrystallization peak signified the ongoing process of crystal perfection and, if any, the formation of secondary crystals during the heating scan. Double melting endotherms appeared for the isothermally melt‐crystallized PLLA samples at 110 °C. TMDSC analysis found that the double lamellar thickness model, other than the melting‐recrystallization model, was responsible for the double melting peaks in PLLA nanocomposites. Polarized optical microscopy images found that the nucleation rate of PLLA was enhanced by MWNTs. TMDSC analysis found that the incorporation of MWNTs caused PLLA to decrease the heat‐capacity increase (namely, ΔC_p) and the C_p at glass transition temperature. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1870–1881, 2007     

Diphenol miscibility effect on the immiscible polyester/polyether binary blends through intermolecular hydrogen‐bonding interaction

Miscibility and hydrogen bonding interaction have been investigated for the binary blends of poly(butylene adipate‐co‐44 mol % butylene terephthalate)[P(BA‐co‐BT)] with 4,4'‐thiodiphenol (TDP) and poly(ethylene‐ oxide)(PEO) with TDP; and the ternary blends of P(BA‐co‐BT)/PEO/TDP by differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FTIR). The DSC results indicated that the binary blends of P(BA‐co‐BT)/TDP and PEO/TDP were miscible because each blend showed only one composition‐dependent glass‐transition over the entire range of the blend composition. The formation of intermolecular hydrogen bonds between the hydroxyl groups of TDP and the carbonyl groups of P(BA‐co‐BT), and between the hydroxyl groups of TDP and the ether groups of PEO was confirmed by the FTIR spectra. According to the glass‐transition temperature measured by DSC, P(BA‐co‐BT) and PEO, their binary blends were immiscible over the entire range of blend composition, however, the miscibility between P(BA‐co‐BT) and PEO was enhanced through the TDP‐mediated intermolecular hydrogen bonding interaction. It was concluded that TDP content of about 5–10% may possibily enhance miscibility between P(BA‐co‐BT) and PEO via a hydrogen bonding interaction. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2971–2982, 2004     

Thermal Properties of Poly(L-lactide)/Calcium Carbonate Nanocomposites

Summary: Thermal properties of nanocomposites prepared of poly(L-lactide) (PLLA) and CaCO₃ applying differential scanning (DSC) calorimetry and thermogravimetry (TG) were studied. Nanocomposites were prepared by extrusion process at 170 °C. DSC measurements show that CaCO₃ has no influence on glass transition and melting point of PLLA but lowers its cold crystallization temperature. There is no difference in glass transition temperature of PLLA before and after extrusion. High temperature thermal stability of the PLLA in the composites is poorer than neat PLLA. Kinetic parameters also indicate greater reactivity of the system upon CaCO₃ addition.     

Crystallization and melting of a branched polyethylene with precisely controlled chemical structure

The heat capacity of a linear polyethylene with dimethyl branches, at every 21st backbone atom was analyzed by differential scanning calorimetry (DSC) and quasi-isothermal temperature-modulated DSC. This novel copolyethylene (PE2M) is relatively difficult to crystallize from the melt. On subsequent heating, a first, sharp melting peak is followed by a sharp cold-crystallization and crystal perfection and a smaller endotherm, before reaching the main melting at 315–320 K, close to the melting temperatures of eicosane and tetracontane. The low-temperature melting is sensitive to the cooling rate and disappears below 1.0 K min⁻¹. The cold crystallization can be avoided by heating with rates faster than 80 K min⁻¹. The PE2M exhibits some reversing and reversible melting, which is typical for chain-folded polymers. The glass transition of semicrystalline PE2M is broadened and reaches its upper limit at about 260 K (midpoint at about 0.355 K). Above this temperature, the crystals seem to have a heat capacity similar to that of the liquid. A hypothesis is that the melting transition can be explained by changes in crystal perfection without major alteration of the crystal structure and the lamellar morphology. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3461–3474, 2006     

Thermal analysis of poly(2-methylpentamethylene terephthalamide)

Poly(2-methylpentamethylene terephthalamide) (Nylon M5T) is a new high temperature aromatic polyamide developed by Hoechst Celanese. In this paper thermal properties of Nylon M5T chips, as well as as-spun and drawn fibers were studied by DSC, DMA, hot stage microscopy and WAXS.T _g of the fully amorphous Nylon M5T is 143°C when measured by DSC;T _g increases with crystallinity to 151°C. The temperature dependence of the solid and melt specific heat capacities has also been determined. The heat capacity increase at the glass transition of the amorphous polymer is 103.9 J °C^–1 mol^–1.T _g by DMA for the as-spun fiber is 155°C, for a drawn fiber is 180°C. Three secondary transitions were observed by DMA in addition to the glass transition. These correspond to a local mode relaxation of the methylene groups at –120°C, onset of rotation of the amide-groups at –65°C and the onset of the rotation of the phenylenegroups (at 63°C). The crystallinity of Nylon M5T strongly depends on the rate of cooling from the melt. The isothermal crystallization data are melt temperature dependent: two-dimensional crystallization takes place when the samples are crystallized from higher melt temperatures, and this phase changes into a spherulitic structure during cooling to room temperature. Spherulitic crystallization occurs when lower melt temperatures are used. This polymer has three crystal forms as indicated by DSC, DMA and WAXS data. The crystal to crystal transitions are clearly visible when amorphous samples are heated in the DSC, or the DMA curves of as-spun fibers are recorded. It is experimentally shown that a considerable melting of the lower temperature crystal forms takes place during the crystal to crystal transitions. The equilibrium melting point as measured by the Hoffman-Weeks method, has been determined to be 339°C.Dedicated to Professor Bernhard Wunderlich on the occasion of his 65th birthday     

改性羟基磷灰石/聚乳酸纳米复合材料的结晶行为

利用溶剂复合的方法制备了具有良好生物相容性的表面接枝聚(γ-苄基-L-谷氨酸)的改性羟基磷灰石/聚乳酸纳米复合材料, 并研究了其熔融与结晶行为. 结果表明, 聚乳酸的玻璃化转变温度为60.3 ℃, 而复合材料的玻璃化转变温度达到65.8 ℃, 不同样品在140 ℃等温结晶后, 改性羟基磷灰石/聚乳酸复合材料的球晶直径仅为聚乳酸(PLLA)球晶直径的16.7%~66.7%. 复合材料的熔点提高到184.4 ℃.     

蓖麻油与乳酸的共聚物合成与表征

用熔融聚合法合成了一种蓖麻油和乳酸的共聚物.以丁二酸酐作为共聚体系的引发剂和封端剂,制得端羧基共聚物P(LA-CO)-COOH.研究了反应条件对共聚物分子量的影响,通过核磁共振表征了共聚物的结构.DSC和TG研究表明,蓖麻油链段的引入破坏了聚乳酸的结晶性,提高了共聚物的热稳定性.     

On the kinetics of melting and crystallization of poly(l-lactic acid) by TMDSC

The crystallization and melting process of poly(l-lactic acid), PLLA, is investigated by temperature modulated differential scanning calorimetry, TMDSC. The sample is cooled from the melt to different temperatures and the crystallization process is followed by subjecting the material to a modulated quasi-isothermal stage. From the average component of the heat flow and the application of the Lauritzen–Hoffman theory two crystallization regimes are identified with a transition temperature around 118 °C. Besides, the oscillating heat flow allows calculating the crystal growth rate via the model proposed by Toda et al., what gives, in addition, an independent determination of the transition temperature from modulated experiments. Further, the kinetics of melting is studied by modulated heating scans at different frequencies. A strong frequency dependence is found both in the real and imaginary part of the complex heat capacity in the transition region. The kinetic response of the material to the temperature modulation is analyzed with the model proposed by Toda et al. Finally, step-wise quasi-isothermal TMDSC was used to investigate the reversible surface crystallization and melting both on cooling and heating and a small excess heat capacity is observed.