Mechanism of PtIV Sonochemical Reduction in Formic Acid Media and Pure Water

Sonochemical synthesis of platinum nanoparticles (Pt NPs) in formic acid solutions and pure water was investigated using a 20 kHz ultrasonic irradiation. The obtained results gave new insights on the underneath Pt^IV reduction mechanism in formic acid media under argon and in pure water under Ar/CO atmosphere. It was shown that in pure water sonochemical reduction of platinum ions occurs by hydrogen issued from homolytic water molecule split. Pt^IV ion reduction appears to be a very slow process under argon atmosphere in pure water due to formation of oxidizing species like OH radicals and H₂O₂ leading to reoxidation of intermediate Pt^II ions. Sonochemical reduction is accelerated manifold in the presence of formic acid or Ar/CO gas mixture. Solution and gas‐phase analyses reveal that both CO and HCOOH act as OH^. radical scavenger and reducing agent under ultrasonic irradiation. Their ability to reduce platinum ions at room temperature is enhanced due to the local heating in the liquid shell surround the cavitation bubble. An innovative synthesis route for monodispersed Pt NPs in pure water without any templates or capping agents in the presence of Ar/CO gas mixture is then proposed. Obtained Pt NPs within the range of 2–3 nm exhibited a strong stability towards sedimentation in water. Since Ar/CO atmosphere is the only restriction of the process, this procedure can be applied in various media and is also compatible with a large array of experimental conditions.     

In situ PEI and formic acid directed formation of Pt NPs/MWNTs hybrid material with excellent electrocatalytic activity

A hybrid material based on Pt nanoparticles (Pt NPs) and multi-walled carbon nanotubes (MWNTs) was fabricated with the assistance of PEI and formic acid. The cationic polyelectrolyte PEI not only favored the homogenous dispersion of carbon nanotubes (CNTs) in water, but also provided sites for the adsorption of anionic ions PtCl₄²⁻ on the MWNTs’ sidewalls. Deposition of Pt NPs on the MWNTs’ sidewalls was realized by in situ chemical reduction of anionic ions PtCl₄²⁻ with formic acid. The hybrid material was characterized with TEM, XRD and XPS. Its excellent electrocatalytic activity towards both oxygen reduction in acid media and dopamine redox was also discussed.     

Electrocatalytic mechanism and kinetics of SOMs oxidation on ordered PtPb and PtBi intermetallic compounds: DEMS and FTIRS study

The electrocatalytic activities and mechanisms of PtPb and PtBi ordered intermetallic phases towards formic acid, formaldehyde and methanol oxidation have been studied by DEMS and FTIRS, and the results compared to those for a pure polycrystalline platinum electrode. While PtPb exhibits an enhanced electrocatalytic activity for the oxidation of all three organic molecules when compared to a Pt electrode, PtBi exhibits an enhanced catalytic activity towards formic acid and formaldehyde oxidation, but not methanol. FTIRS data indicate that adsorbed CO does not form on PtPb or PtBi intermetallic compounds during the oxidation of formic acid, formaldehyde and methanol, and therefore their oxidation on both PtPb and PtBi intermetallic compounds proceeds via a non-CO(ads) pathway. Quantitative DEMS measurements indicate that only CO(2) was detected as a final product during formic acid oxidation on Pt, PtPb and PtBi electrodes. At a smooth polycrystalline platinum electrode, the oxidation of formaldehyde and methanol produces mainly intermediates (formaldehyde and formic acid), while CO(2) is a minor product. In contrast, CO(2) is the major product for formaldehyde and methanol oxidation at a PtPb electrode. The high current efficiency of CO(2) formation for methanol and formaldehyde oxidation at a PtPb electrode can be ascribed to the complete dehydrogenation of formaldehyde and formic acid due to electronic effects. The low onset potential, high current density and high CO(2) yield make PtPb one of the most promising electrocatalysts for fuel cell applications using small organic molecules as fuels.     

Synthesis of hollow and nanoporous gold/platinum alloy nanoparticles and their electrocatalytic activity for formic acid oxidation

In this work, hollow Au/Pt alloy nanoparticles (NPs) with porous surfaces were synthesized in a two-step procedure. In the first step, tri-component Ag/Au/Pt alloy NPs were synthesized through the galvanic replacement reaction between Ag NPs and aqueous solutions containing a mixture of HAuCl₄ and H₂PtCl₄. In the second step, the Ag component was selectively dealloyed with nitric acid (HNO₃), resulting in hollow di-component Au/Pt alloy NPs with a porous surface morphology. The atomic ratio of Au to Pt in the NPs was easily tunable by controlling the molar ratio of the precursor solution (HAuCl₄ and H₂PtCl₆). Hollow, porous Au/Pt alloy NPs showed enhanced catalytic activity toward formic acid electrooxidation compared to the analogous pure Pt NPs. This improved activity can be attributable to the suppression of CO poisoning via the “ensemble” effect.     

一种提高铂电催化氧化甲酸性能的简单方法

在离子液体1-乙基咪唑三氟乙酸盐(HElmTfa)中,采用循环伏安法在铂电极表面修饰聚吡咯(PPY),制得PPy-HEImTfa/Pt,并研究了其对甲酸的电催化氧化性能.与相同条件下的铂基底电极相比,PPy-HEImTfa/Pt对甲酸的电催化氧化性能有很大的提高.原位红外光谱表明,PPy-HElmTfa能降低中间体CO等对铂电极的毒化作用,促进甲酸直接氧化生成CO_2.     

Studies on the photoactivation of two cytotoxic trans,trans,trans-diazidodiaminodihydroxo-Pt(IV) complexes

Light-activation of metal ion complexes to cytotoxic species is of interest due to the potential use in anticancer therapy. Two platinum complexes, trans,trans,trans-[Pt(IV)(N(3))(2)(OH)(2)(NH(3))(2)] (3) and trans,trans,trans-[Pt(IV)(N(3))(2)(OH)(2)(py)(NH(3))] (4) were irradiated with either UV (λ = 366 nm) or white fluorescent light and the various photochemical and photobiological phenomena were characterized. HPLC coupled to UV/Vis and MS detection was used to identify photochemical species resulting from irradiation of 4 with UV and white light. These studies showed that various Pt(IV) and Pt(II) products formed during the photolysis. The mass spectra of Pt(IV) complexes showed Pt ions in both the positive as well as the negative mode while Pt(II) complexes resulted in only positively charged Pt(III) ions. Since cellular DNA is considered to be a key target for platinum antitumor drugs, the irreversible platination of calf thymus DNA by the photoactivated Pt(IV) complexes was followed by Atomic Adsorption spectrometry (AAS). The effect of adding chloride or biological reducing agents glutathione (GSH) and ascorbic acid on the rates of DNA platination where also studied. Upon activation by light, both compounds show similar binding behaviour to DNA, but the rates of DNA platination for 3 were faster than for 4. Both chloride and GSH protected DNA from platination by the photoactivated compounds; consistent with the trapping of reactive aqua-Pt species. The presence of ascorbate increased the level of platinum bound to DNA for photoactivated 4 but not for 3. Without photoactivation, little or no DNA platination was observed, either with or without ascorbate or GSH. Cytotoxicity studies with two human cancer cell lines underline the photochemotherapeutic potential of these compounds. Striking is the increase in cytotoxic potency with the replacement of an ammine by a pyridine ligand.     

An influence of pretreatment conditions on surface structure and reactivity of Pt(100) towards CO oxidation reaction

We present a combined electrochemical and in situ STM study of the surface structure of Pt(100) single crystal electrodes in dependence on the cooling atmosphere after flame annealing. The following cooling conditions were applied: Ar/H₂ and Ar/CO mixtures (reductive atmosphere), argon (inert gas) and air (oxidative atmosphere). Surface characterization by in-situ STM allows deriving direct correlations between surface structure and macroscopic electrochemical behavior of the respective platinum electrodes. We investigated the influence of defect type and density as well as long range surface order on the kinetics of the CO electro-oxidation reaction. The defect-rich Pt(100) electrodes as cooled in air or Ar, and followed by immersion in the hydrogen adsorption region display higher activities as compared to the rather smooth Pt(100)-(1 × 1) electrode cooled in an Ar/H₂-atmosphere.     

Interaction of Au(III) and Pt(IV) complex ions with Fe(II) ions as a scavenging and a reducing agent: a basic study on the recovery of Au and Pt by a chemical method

In order to develop a chemical technique for the recovery of gold (Au) and platinum (Pt) in the metallic state from spent catalysts, e.g., catalysts for environmental protection and automobile and petroleum catalysts, the coprecipitation behaviors of Au(III) and Pt(IV) complex ions with Fe(OH)(2) as a scavenging and reducing agent were investigated. The Au(III) complex ions were found to be stoichiometrically and rapidly reduced to metallic Au due to electron transfer in acidic aqueous solution prior to coprecipitation with Fe(OH)(2). Conversely, Pt(IV) complex ions were reduced only after coprecipitation with Fe(OH)(2) due to electron transfer through a Pt(IV)-O-Fe(II) bond on the solid Fe(OH)(2). Using this chemical technique, Au and Pt can be selectively and effectively recovered in the metallic state.     

Probing the formation mechanism and chemical states of carbon-supported Pt-Ru nanoparticles by in situ X-ray absorption spectroscopy

The understanding of the formation mechanism of nanoparticles is essential for the successful particle design and scaling-up process. This paper reports findings of an X-ray absorption spectroscopy (XAS) investigation, comprised of X-ray absorption near-edge structure (XANES) and extended X-ray absorption fine structure (EXAFS) regions, to understand the mechanism of the carbon-supported Pt-Ru nanoparticles (NPs) formation process. We have utilized Watanabe's colloidal reduction method to synthesize Pt-Ru/C NPs. We slightly modified the Watanabe method by introducing a mixing and heat treatment step of Pt and Ru oxidic species at 100 degrees C for 8 h with a view to enhance the mixing efficiency of the precursor species, thereby one can achieve improved homogeneity and atomic distribution in the resultant Pt-Ru/C NPs. During the reduction process, in situ XAS measurements allowed us to follow the evolution of Pt and Ru environments and their chemical states. The Pt LIII-edge XAS indicates that when H2PtCl6 is treated with NaHSO3, the platinum compound is found to be reduced to a Pt(II) form corresponding to the anionic complex [Pt(SO3)4]6-. Further oxidation of this anionic complex with hydrogen peroxide forms dispersed [Pt(OH)6]2- species. Analysis of Ru K-edge XAS results confirms the reduction of RuIIICl3 to [RuII(OH)4]2- species upon addition of NaHSO3. Addition of hydrogen peroxide to [RuII(OH)4]2- causes dehydrogenation and forms RuOx species. Mixing of [Pt(OH)6]2- and RuOx species and heat treatment at 100 degrees C for 8 h produced a colloidal sol containing both Pt and Ru metallic as well as ionic contributions. The reduction of this colloidal mixture at 300 degrees C in hydrogen atmosphere for 2 h forms Pt-Ru nanoparticles as indicated by the presence of Pt and Ru atoms in the first coordination shell. Determination of the alloying extent or atomic distribution of Pt and Ru atoms in the resulting Pt-Ru/C NPs reveals that the alloying extent of Ru (JRu) is greater than that of the alloying extent of Pt (JPt). The XAS results support the Pt-rich core and Ru-rich shell structure with a considerable amount of segregation in the Pt region and with less segregation in the Ru region for the obtained Pt-Ru/C NPs.     

One-step pyrolysis process to synthesize dispersed Pt/carbon hollow nanospheres catalysts for electrocatalysis

An effective method for loading Pt nanoparticles on monodispersed hollow carbon nanospheres by one-step pyrolysis of polystyrene spheres (PS) adsorbed with platinum (IV) ions was developed. The polystyrene spheres were firstly enwrapped with a layer of sucrose and cetyltrimethyl ammonium bromide (CTAB) micelles. Adsorption of platinum (IV) ions onto the polystyrene spheres was carried out via electrostatic interaction between the negatively charged platinum salt and the positively charged amino group in the CTAB. Pyrolysis of the PS-Pt (IV) precursors at 600 °C under nitrogen atmosphere resulted in the simultaneous decomposition of the sucrose to carbon and the adsorbed platinum complex to metallic Pt. During this process the polystyrene spheres was removed and hollow sphere of PtC formed. Nanocomposites of hollow carbon nanospheres with different platinum loading were synthesized and their electrocatalytic activity was evaluated using methanol as a model molecule. Results showed that the as-prepared hollow carbon nanospheres supported platinum catalysts have high electrocatalytic activity and long-term stability towards the oxidation of methanol. The present method is promising for the fabrication of carbon supported platinum catalysts for the direct methanol fuel cell.     

The electrooxidation of small organic molecules on platinum nanoparticles supported on gold: influence of platinum deposition procedure

The electrocatalytic properties of small platinum nanoparticles were investigated for the oxidation of CO, methanol, and formic acid using voltammetry, chronoamperometry, and surface-enhanced Raman spectroscopy. The particles were generated by galvanostatic deposition of platinum on a polished gold surface from an H₂PtCl₆ containing electrolyte and ranged between 10 and 20 nm in diameter for low platinum surface concentrations, 10 and 120 nm for medium concentrations, and full Pt monolayers for high concentrations. CO stripping and bulk CO oxidation experiments on the particles up to 120 nm in diameter displayed pronounced structural effects. The CO oxidation current-time transients show a current decay for low platinum coverages and a current maximum for medium and high coverages. These results were also observed in the literature for particles of 2- to 5-nm size and agglomerates of these particles. The similarities between the literature and our results, despite large differences in particle size and morphology, suggest that particle structure and morphology are also very important catalytic parameters. Surface-enhanced Raman spectroscopy data obtained for the oxidation of CO on the Pt-modified Au electrodes corroborate this conclusion. A difference in the ratio between CO adsorbed in linear- and bridge-bonded positions on the Pt nanoparticles of different sizes demonstrates the influence of the surface morphology. The oxidation activity of methanol was found to decrease with the particle size, while the formic acid oxidation rate increases. Again, a structural effect is observed for particles of up to ca. 120 nm in diameter, which is much larger than the particles for which a particle size effect was reported in the literature. The particle shape effect for the methanol oxidation reaction can be explained by a reduction in available “ensemble sites” and a reduction in the mobility of CO formed by decomposition of methanol. As formic acid does not require Pt ensemble sites, decreasing the particle size, and thus, the relative number of defects, increases the reaction rate. Dedicated to Prof. Dr. Teresa Iwasita on the occasion of her 65th birthday in recognition of her numerous contributions to interfacial electrochemistry.     

Formation of Pt-Ru nanoparticles in ethylene glycol solution: an in situ X-ray absorption spectroscopy study

The chemical state and formation mechanism of Pt-Ru nanoparticles (NPs) synthesized by using ethylene glycol (EG) as a reducing agent and their stability have been examined by in situ X-ray absorption spectroscopy (XAS) at the Pt LIII and Ru K edges. It appears that the reduction of Pt(IV) and Ru(III) precursor salts by EG is not a straightforward reaction but involves different intermediate steps. The pH control of the reaction mixture containing Pt(IV) and Ru(III) precursor salts in EG to 11 led to the reduction of Pt(IV) to Pt(II) corresponding to [PtCl4](2-) whereas Ru(III)Cl3 is changed to the [Ru(OH)6](3-) species. Refluxing the mixture containing [PtCl4](2-) and [Ru(OH)6](3-) species at 160 degrees C for 0.5 h produces Pt-Ru NPs as indicated by the presence of Pt and Ru in the first coordination shell of the respective metals. No change in XAS structural parameters is found when the reaction time is further increased, indicating that the Pt-Ru NPs formed are extremely stable and less prone to aggregation. XAS structural parameters suggest a Pt-rich core and a Ru-rich shell structure for the final Pt-Ru NPs. Due to the inherent advantages of the EG reduction method, the atomic distribution and alloying extent of Pt and Ru in the Pt-Ru NPs synthesized by the EG method are higher than those of the Pt-Ru/C NPs synthesized by a modified Watanabe method.     

甲醇在欠电位沉积Sn/Pt电极上催化氧化

在欠电位沉积（upd）锡修饰的铂电极（upd-Sn/Pt）上,对甲醇电化学催化氧化过程进行了研究.发现当Pt表面upd-Sn的覆盖率在20％附近时,对甲醇的催化氧化的增强作用最为明显；在电位低于0.35 V （vs RHE）时,甲醇在Pt与upd-Sn/Pt电极上氧化只进行到脱氢生成CO的步骤;在0.35 V以后,表面Sn－OH形成,反应Sn－OH＋COads=Sn＋CO2＋H＋＋e有利于表面CO的去除;而Pt电极上,只有0.6 V以后,才有反应Pt－OH＋COads=Pt＋CO2＋H＋＋e发生.因此,Sn的存在有利于甲醇在较低的电位下氧化; Pt电极上CH3OH脱氢并释放出电子的过程是一个快速的过程,表面CO的去除是甲醇氧化过程的控制步骤;甲醇氧化产生的表面吸附态CO 以线式吸附为主,少量的桥式吸附态CO在反应初期即达到吸附饱和; Pt表面上upd-Sn表现的催化增强作用,在光亮铂电极和在高分散铂黑电极上是一致的.     

Rotating ring-disk voltammetry: Diagnosis of catalytic activity of metallic copper catalysts toward CO<Subscript>2</Subscript> electroreduction

Using the rotating ring (platinum)—disk (glassy carbon) electrode methodology, electrocatalytic activity of the microstructured copper centers (imbedded within the polyvinylpyrrolidone polymer matrix and deposited onto the glassy carbon disk electrode) has been monitored during electroreduction of carbon dioxide both in acid (HClO₄) and neutral (KHCO₃) media as well as diagnosed (at Pt ring) with respect to formation of the electroactive products. Combination of the stripping-type and rotating ring-disk voltammetric approaches has led to the observation that, regardless the overlapping reduction phenomena, the reduction of carbon dioxide at copper catalyst is, indeed, operative and coexists with hydrogen evolution reaction. Using the fundamental concepts of surface electrochemistry and analytical voltammetry, the reaction products (thrown onto the platinum ring electrode) could be considered and identified as adsorbates (on Pt) under conditions of the stripping-type oxidation experiment. Judging from the potentials at which the stripping voltammetric peaks appear in neutral CO₂-saturated KHCO₃ (pH 6.8), formic acid or carbon monoxide seem to be the most likely reaction products or intermediates. The proposed methodology also permits correlation between the CO₂ electroreduction products and the potentials applied to the disk electrode. By performing the comparative stripping-type voltammetric experiments in acid medium (HClO₄ at pH 1) with the adsorbates of formic acid, ethanol and acetaldehyde (on Pt ring), it can be rationalized that, although C₂H₅OH or CH₃CHO are very likely CO₂-reduction electroactive products, formation of some HCOOH, CH₃OH or even CO cannot be excluded.     

Synthesis of Pt/Ru bimetallic nanoparticles in high-temperature and high-pressure fluids

A high-temperature and high-pressure flow-reactor system was applied to the synthesis of monometallic ruthenium (Ru) nanoparticles and platinum/ruthenium (Pt/Ru) bimetallic nanoparticles using the thermal reduction of ruthenium ion (Ru(III)) and the mixture of platinum (Pt(IV)) and ruthenium ions in water and ethanol mixture in the presence of poly(N-vinyl-2-pyrrolidone). Monometallic Ru nanoparticles with an average diameter of ca. 2 nm were synthesized above 200 degrees C at 30 MPa. The monometallic Ru nanoparticles tended to make large aggregates in colloidal dispersions. By the reduction of the mixture solution of Pt(IV) and Ru(III) in water and ethanol above 200 degrees C at 30 MPa, Pt/Ru bimetallic nanoparticles with an average diameter of ca. 2.5 nm were synthesized with relatively small size distribution. The EXAFS spectra for the Pt/Ru bimetallic particles indicated that the particle possesses metallic bonds between Pt and Ru atoms in contrast to the case of the nanoparticles produced by thermal reduction under ambient pressure at 100 degrees C [M. Harada, N. Toshima, K. Yoshida, S. Isoda, J. Colloid Interface Sci. 283 (2005) 64], and that the Pt/Ru bimetallic particle has a Pt-core/Ru-shell structure.     

Kinetics of dissociative adsorption of formic acid on electrodes of tetrahexahedral platinum nanocrystals

In the present paper we study the kinetics of dissociative adsorption of formic acid on the electrode of tetrahexahedral platinum nanocrystals (THH Pt NCs). In situ FTIR spectroscopic results demonstrate that HCOOH can be oxidized to CO2 at a low potential (-0.2 V(SCE)) on the THH Pt NCs electrode, and the chemical bonds inside formic acid molecule are broken to form adsorbed COL species. The kinetics of the dissociative adsorption of HCOOH was quantitatively investigated by employing programmed potential s...     

Preparation and enhanced visible-light photocatalytic H2-production activity of CdS-sensitized Pt/TiO2 nanosheets with exposed (001) facets

CdS-sensitized Pt/TiO(2) nanosheets with exposed (001) facets were prepared by hydrothermal treatment of a Ti(OC(4)H(9))(4)-HF-H(2)O mixed solution followed by photochemical reduction deposition of Pt nanoparticles (NPs) on TiO(2) nanosheets (TiO(2) NSs) and chemical bath deposition of CdS NPs on Pt/TiO(2) NSs, successively. The UV and visible-light driven photocatalytic activity of the as-prepared samples was evaluated by photocatalytic H(2) production from lactic acid aqueous solution under UV and visible-light (λ ≥ 420 nm) irradiation. It was shown that no photocatalytic H(2)-production activity was observed on the pure TiO(2) NSs under UV and/or visible-light irradiation. Deposition of CdS NPs on Pt/TiO(2) NSs caused significant enhancement of the UV and visible-light photocatalytic H(2)-production rates. The morphology of TiO(2) particles had also significant influence on the visible-light H(2)-production activity. Among TiO(2) NSs, P25 and the NPs studied, the CdS-sensitized Pt/TiO(2) NSs show the highest photocatalytic activity (13.9% apparent quantum efficiency obtained at 420 nm), exceeding that of CdS-sensitized Pt/P25 by 10.3% and that of Pt/NPs by 1.21%, which can be attributed to the combined effect of several factors including the presence of exposed (001) facets, surface fluorination and high specific surface area. After many replication experiments of the photocatalytic hydrogen production in the presence of lactic acid, the CdS-sensitized Pt/TiO(2) NSs did not show great loss in the photocatalytic activity, confirming that the CdS/Pt/TiO(2) NSs system is stable and not photocorroded.     

Trimetallic Au@PdPt core-shell nanoparticles with ultrathin PdPt skin as highly stable electrocatalysts for the oxygen reduction reaction in acid solution

To design efficient and low-cost core-shell electrocatalysts with an ultrathin platinum shell, the balance between platinum dosage and durability in acid solution is of great importance. In the present work, trimetallic Au@PdPt core-shell nanoparticles(NPs)with Pd/Pt molar ratios ranging from 0.31:1 to 4.20:1 were synthesized based on the Au catalytic reduction strategy and the subsequent metallic replacement reaction. When the Pd/Pt molar ratio is 1.19:1(designated as Au@Pd_(1.19) Pt_1 NPs), the superior electrochemical activity and stability were achieved for oxygen reduction reaction(ORR) in acid solution. Especially, the specific and mass activities of Au@Pd_(1.19) Pt_1 NPs are 1.31 and 6.09 times higher than those of commercial Pt/C catalyst. In addition, the Au@Pd_(1.19) Pt_1 NPs presented a good durability in acid solution. After 3000 potential cycles between 0.1 and 0.7 V(vs. Ag/AgCl), the oxygen reduction activity is almost unchanged. This study provides a simple strategy to synthesize highperformance trimetallic ORR electrocatalyst for fuel cells.     

Towards Mixed Fuels: The Electrochemistry of Hydrazine in the Presence of Methanol and Formic Acid

The electrochemistry of formic acid, carbon monoxide and methanol have been investigated and evaluated in combination with hydrazine. Hydrazine was observed to display the anticipated steady‐state oxidation waves at platinum (Pt) microelectrodes by cyclic voltammetry, and upon introduction of carbon monoxide (CO) gas, the Pt surface was fully passivated (prior to CO oxidation). However, the two individual responses of hydrazine and formic acid (HCOOH) are to be additive when combined in solution. No detrimental effects were observed upon the hydrazine voltammetry, even in the presence of excess formic acid, despite formic acid clearly displaying characteristic self‐poisoning tendencies (primarily due to the formation of CO) in its own voltammetry. Effects intermediate to those of CO and formic acid were observed when methanol was present. Currents were essentially additive at low methanol content, but hydrazine oxidation current decreased by about 40 % when an 100‐fold excess of methanol was present, corresponding to poisoning by methanol dehydrogenation intermediates. These results are discussed with relevance to mixed fuels for more flexible or powerful fuel cells, and the possible formation of a random microelectrode array (templated by strongly adsorbed poison) on the microelectrode surface.     

Influence of ultrathin poly-(3,4-ethylenedioxythiophene) (PEDOT) film supports on the electrodeposition and electrocatalytic activity of discrete platinum nanoparticles

Coating a carbon electrode surface, specifically highly oriented pyrolytic graphite (HOPG) with an ultrathin film of poly-(3,4-ethylenedioxythiophene), PEDOT, provides a support on which a high density of uniformly dispersed Pt nanoparticles (NPs) can readily be formed by electrodeposition. The NPs tend to be much smaller, have a higher surface coverage, better dispersion and show a much lower tendency to aggregate, than Pt NPs produced under identical electrochemical conditions on HOPG alone. The electrocatalytic activity of the NPs was investigated for methanol (MeOH) and formic acid (HCOOH) oxidation. Significantly, for similarly prepared particles, Pt NP-PEDOT arrays exhibited higher catalytic activity (in terms of current density, based on the Pt area), towards MeOH oxidation, by an order of magnitude, and towards HCOOH oxidation at high potentials, than Pt NPs supported on native HOPG. These findings can be rationalised in terms of the enhanced oxidation of adsorbed CO, a key reaction intermediate and a catalyst poison. This research provides strong evidence that employing conducting polymers, such as PEDOT, as a support substrate, can greatly improve particular catalytic reactions, allowing for better catalyst utilisation in fuel cell technology.