Measurement of carbonyls in exhaust gases of light-duty vehicles in China using pentafluorophenyl hydrazine derivatisation and GC/MS analysis

A method for determining carbonyl emissions from motor vehicles was developed in which exhaust gases from test vehicles running on a dynamometer are directly collected in 6-L Teflon bags and then introduced into pentafluorophenyl hydrazine -coated adsorbent tubes for derivatisation and subsequent analysis of generated derivatives by GC/MS. Twenty gasoline and LPG light-duty vehicles were sampled at a vehicle inspection station in Guangzhou, China, by running test vehicles over a transient testing cycle and analysed for carbonyls. Results show that the method can achieve a detection limit of 8–28 ng m^?3 for individual carbonyls with a relative standard deviation of 14.5%. Twenty-four carbonyls were identified in the gasoline vehicle exhaust gases and their total concentration was 19.2 mg m^?3. For the LPG vehicles, 20 carbonyls were found in the exhaust gases with a total concentration of 4.71 mg m^?3. Based on the results, carbonyl emission factors for the gasoline and LPG vehicles were estimated to be 25.0 and 7.36 mg km^?1, respectively.     

Coordination of extraframework Li+ cation in the MCM-22 and MCM-36 zeolite: FTIR study of CO adsorbed

Nature and population of Li⁺ cationic sites in MCM-22 zeolite and its pillared form (MCM-36) were investigated by means of adsorption of CO as a probe molecule. CO stretching frequency and adsorption heat were measured by FTIR spectroscopy and adsorption microcalorimetry. Intrazeolitic carbonyl complexes on Li⁺ cations in MCM-22 and MCM-36 are characterized by two main vibrational bands at 2,195 and 2,188 cm^?1. Band at higher wavenumbers is ascribed to carbonyls on Li⁺ ions coordinated only to two oxygen atoms at the intersection of 10-ring channels and interacting with CO molecule by energy around 45 kJ mol^?1. Band at 2,188 cm^?1 was assigned to the carbonyls on Li⁺ cations located on top of 5 or 6-rings on the channel walls and coordinated to three or four oxygen atoms, interacting with CO molecule by energy 33–36 kJ mol^?1. Effect of pillaring and layered form of zeolite on nature and population of Li⁺ cationic sites is also discussed, as well as the formation of dicarbonyl complexes.     

Electrocatalytic oxidation of methanol by ZSM-5 nanozeolite-modified carbon paste electrode in alkaline medium

Development of a novel modified electrode for electrocatalytic oxidation of methanol in order to decrease overvoltage is importance. In this paper, carbon paste electrode (CPE) was modified by ZSM-5 nanozeolite. The average diameter of used nanozeolite was 97 nm. Ni²⁺ ions were incorporated to the nanozeolite by immersion of the modified electrode in a 0.1 M nickel chloride solution. Then, electrochemical studies of this electrode were performed by using cyclic voltammetry(CV) in alkaline medium. This modified electrode was used as an anode for the electrocatalytic oxidation of methanol in 0.1 M of NaOH solution. The obtained data demonstrated that ZSM-5 nanozeolite at the surface of CPE improves catalytic efficiency of the dispersed nickel ions toward methanol oxidation. The values of electron transfer coefficient, charge-transfer rate constant, and the electrode surface coverage are obtained 0.61, 0.2342 s^?1, and 4.33 × 10^?8 mol cm^?2, respectively. Also, the mean value of catalytic rate constant between the methanol and redox sites of electrode and diffusion coefficient were found to be 2.54 × 10⁴ cm³ mol^?1 s^?1 and 1.85 × 10^?8 cm² s^?1, respectively. Obtained results from both CV and chronoamperometric techniques indicated that the electrode reaction is a diffusion-controlled process.     

Degradation of azithromycin using Ti/RuO<Subscript>2</Subscript> anode as catalyst followed by DPV,HPLC–UV and MS analysis

The electrodegradation of azithromycin was studied by its indirect oxidation using dimensionally stable Ti/RuO₂ anode as catalyst in the electrolyte containing methanol, 0.05 M NaHCO₃, sodium chloride and deionized water. The optimal conditions for galvanostatic electrodegradation for the azithromycin concentration of 0.472 mg cm^?3 were found to be NaCl concentration of 7 mg cm^?3 and the applied current of 300 mA. The differential pulse voltammetry using glassy carbon electrode was performed for the first time in the above-mentioned content of electrolyte for the nine concentration of azithromycin (0.075–0.675 mg cm^?3) giving the limits of azithromycin detection and of quantification as: LOD 0.044 mg cm^?3 and LOQ 0.145 mg cm^?3. The calibration curve was constructed enabling the electrolyte analysis during its electrodegradation process. The electrolyte was analyzed by high-performance liquid chromatography and electrospray ionization time-of-flight mass spectrometry. The electrooxidation products were identified and after 180 min there was no azithromycin in the electrolyte while TOC analysis showed that 79% of azithromycin was mineralized. The proposed degradation scheme is presented.     

Synthesis and characterization of activated carbon–ethylenediamine–cobalt(II) tetracarboxyphthalocyanine conjugate for catalytic oxidation of ascorbic acid

We report on the synthesis and characterization of activated carbon–ethylenediamine–cobalt(II) tetracarboxyphthalocyanine conjugate (AC–CONHCH₂CH₂NH₂–CoPc) and its electrocatalytic behavior for oxidation of ascorbic acid. Ultraviolet–visible (UV–Vis), Fourier-transform infrared (FTIR), and electrochemical impedance spectroscopies, and cyclic and square-wave voltammetry were used to characterize the electrode modifiers and modified glassy carbon electrode. The limit of detection was found to be 0.26 µm using 3δ notation. The linear dynamic range was from 1.5 × 10^?4 to 1 × 10^?2 M with electrode sensitivity of 0.01 A mol^?1 L cm^?2. A Tafel slope of 200.8 mV decade^?1 was found. The concentration of ascorbic acid in the tablet was 0.034 M. Oxalic acid showed no interference in ascorbic acid determination.     

Facile preparation of nitrogen-doped graphene scrolls via acoustic cavitation as electrocatalyst for glucose biosensing

Nitrogen doping is considered as a promising strategy to tailor and develop the intrinsic properties of graphene. In this work, we report a facile method for preparation of nitrogen-doped graphene scrolls (N-GSS) through acoustic cavitation, which can not only realize graphene nitrogen doping but also simultaneously result in its scrolled topological structure and improvement of reduction degree. As a metal-free electrocatalyst, the prepared N-GSS showed good electrocatalytic activity towards oxidation of hydrogen peroxide with the sensitivity of 87.8 μA mM^?1 cm^?2. Then N-GSS was employed as a matrix for glucose oxidase (GOD) loading, and the fabricated biosensor also exhibited excellent analytical characteristics, such as a high sensitivity (55.2 μA mM^?1 cm^?2), wide linear range (2 μM to 3.56 mM, R = 0.999) and low detection limit (1 μM).     

Preparation and characterization of nickel hexacyanoferrate films for the removal of cesium ion by electrically switched ion exchange (ESIX)

The method of electrically switched ion exchange (ESIX) involves the sequential application of reduction and oxidation potentials to an ion exchange film to induce the respective loading and unloading of Cs⁺. In this study, four films of nickel hexacyanoferrate were prepared on nickel electrodes with different preparation procedures. Films were characterized by SEM/EDX. Each film shows a different performance with regard to Cs⁺ separation. Scanning electron microscopy was used to characterize the modified film surfaces. Cyclic voltammetry was used to investigate the ion exchange capacity and stability. The four films show a better capacity for Cs⁺ separation compared to previous methods for the deposition of ESIX films. An optimal nickel hexacyanoferrate film was generated when using an applied potential of 0.2 V relative to a saturated calomel electrode (SCE) to generate the nucleation sites, followed by a 1.3 V vs. SCE potential during the growth stage of the film. This film demonstrated the highest film capacity for ion exchange initially (17.3 × 10^?3 C cm^?2) and again after 1000 cycles (11.1 × 10^?3 C cm^?2).     

Invar<Superscript>®</Superscript> oxidation in CO<Subscript>2</Subscript>

In this article, corrosion of Invar^® in a static carbon dioxide atmosphere \( 2\times 1 0^{4} \le P_{{{\text{CO}}_{ 2} }} \le 10^{5} \,{\text{Pa}} \) has been studied between 1163 and 1263 K. At the beginning, after a short initial deceleration for weight gains Δm/S <0.5 mg cm^?2, oxidation kinetics were linear up to weight gains of about 4.0 mg cm^?2, and only wüstite Fe_1?x O was formed with a constant rate r (mg cm^?2 s^?1) \( r = \frac{{{\text{d}}\left( {\frac{\Updelta m}{S}} \right)}}{{{\text{d}}t}} = 0.41 \times P_{{{\text{CO}}_{ 2} }} \exp \left( {\frac{ - 198000}{RT}} \right) \) where R is the gas constant and t the time (s). Reaction mechanism is similar to that of the pure iron in analogous conditions, with the same rate limiting step i.e. external reaction of CO₂ with wüstite and outward diffusion of ions Fe²⁺ (not limiting). For weight gains Δm/S higher than 4 mg cm^?2, the limiting step changes, with an increase of the reaction rate and an internal oxidation. The origin of this mechanism change lies in the microcracks appearing in the oxide during its growth. Then, wüstite is no longer bound to the substrate; outward diffusion of ions Fe²⁺ stops and a topotactic transformation converts wüstite into magnetite.     

Synthesis,crystal structure,and FET characteristics of thieno[2,3-b]thiophene-based bent-thienoacenes

Two novel bent-shaped thienoacenes, naphtho[2,3-b]naphtho[2′,3′:4,5]thieno[3,2-d]thiophene (bent-DNTT) and anthra[2,3-b]anthra[2′,3′:4,5]thieno[3,2-d]thiophene (bent-DATT) were synthesized from thieno[2,3-b]thiophene and their corresponding aromatic anhydrides by three steps: Friedel–Crafts acylation, acid-promoted cyclization, and reductive aromatization. The structural curvature improved the solubility of these thienoacenes in organic solvents. The bent-DNTT based FET device was fabricated by the spin-coating method. The device exhibited p-type characteristics with a mobility of 5.1 × 10^?5 cm² V^?1 s^?1. Its thin-film structure was fully characterized as an edge-on orientation with large intermolecular orbital coupling.     

The Catalytic Cycle of Oxidation of Iodide Ion in the Oxygen/Nitrous Acid/Nitric Oxide System and Its Potential for Analytical Applications

Abstract

The oxidation of iodide to iodine by nitrous acid in aqueous acidic medium takes place catalytically in the presence of dissolved oxygen and can be followed spectrophotometrically at 288 and 352 nm. An indirect molar absorptivity for nitrite on the basis of I₃ ^? formation can be as high as 8.5×10⁵ L mol^?1 cm^?1 at 288 nm. Analytical curves were established. The iodine released in the catalytic cycle can also be titrated with thiosulfate. The reaction is pseudo–second‐order in oxygen consumed, with t_1/2=15.7 min at 25°C. A rate determining step could be the NO · O₂ as the activated species. Measurements of the iodine formed at catalytic conditions was used to determine nitrite in meat extracts and NOx in car exhausts.     

Differentiation of Rhizoma Curcumas Longae and Radix Curcumae by a Multistep Infrared Macro-Fingerprint Method

A multistep infrared macro-fingerprint method was applied to identify two Chinese herbal drugs, Rhizoma Curcumas Longae (RCL) and Radix Curcumae (RC). Fourier transform infrared (FT-IR) spectra of the two were similar to each other and consistent with the 11 peaks of the spectrum of starch. RCL had a characteristic absorption peak at approximately 1514 cm^?1 that correlated to the strong peak near 1509 cm^?1 of curcumin. Between 900 cm^?1–1700 cm^?1 of the second derivative infrared (SD-IR) spectra, with higher resolution, RCL, and curcumin had 10 common peaks. In the FT-IR and SD-IR spectra of the ethanol extract, the spectra of the RCL extract and curcumin were similar, but RC was different. According to the fingerprint characteristics of the infrared spectra for RC and its extracts, the strongest peak at 1055 cm^?1; the C-O absorption peaks at 1124 cm^?1, 1106 cm^?1, and 996 cm^?1; and the strong methylene peaks at 2925 cm^?1 and 2853 cm^?1 suggest that RC contains more saccharides. In the range of 1350 cm^?1–1700 cm^?1, RCL and RC had similar two-dimensional infrared (2D-IR) correlation spectra. Both of them had three autopeaks, but the autopeaks were located at 1458 cm^?1, 1560 cm^?1, and 1641 cm^?1 for RCL and 1458 cm^?1, 1560 cm^?1, and 1669 cm^?1 for RC, suggested that the aromatic components of the two were not identical. The average correlation for the 18 RCL and 18 RC samples were 0.9906 and 0.9878, respectively, and this method achieves a good classification of the sample type.     

Direct electrochemistry and electrochemical biosensing of glucose oxidase based on CdSe@CdS quantum dots and MWNT-modified electrode

The direct electron transfer of glucose oxidase (GOx) was achieved based on the immobilization of CdSe@CdS quantum dots on glassy carbon electrode by multi-wall carbon nanotubes (MWNTs)-chitosan (Chit) film. The immobilized GOx displayed a pair of well-defined and reversible redox peaks with a formal potential (E ^θ’) of ?0.459 V (versus Ag/AgCl) in 0.1 M pH 7.0 phosphate buffer solution. The apparent heterogeneous electron transfer rate constants (k _s) of GOx confined in MWNTs-Chit/CdSe@CdS membrane were evaluated as 1.56 s^?1 according to Laviron's equation. The surface concentration (Γ*) of the electroactive GOx in the MWNTs-Chit film was estimated to be (6.52?±?0.01)?×?10^?11?mol?cm^?2. Meanwhile, the catalytic ability of GOx toward the oxidation of glucose was studied. Its apparent Michaelis–Menten constant for glucose was 0.46?±?0.01 mM, showing a good affinity. The linear range for glucose determination was from 1.6?×?10^?4 to 5.6?×?10^?3?M with a relatively high sensitivity of 31.13?±?0.02 μA?mM^?1?cm^?2 and a detection limit of 2.5?×?10^?5?M (S/N=3).     

Direct electrochemical detection of bisphenol A at PEDOT-modified glassy carbon electrodes

The electrochemical behavior of bisphenol A (BPA) was studied on poly(3,4-ethylenedioxythiophene) (PEDOT)-modified glassy carbon electrodes by cyclic voltammetry. It was observed that BPA oxidation on PEDOT film produced a BPA polymer (pBPA) showing excellent redox activity with anodic and cathodic peaks at 0.15 and 0.01 V, respectively; the former being evaluated for BPA electrochemical sensing. The amount of deposited pBPA has been estimated by electrochemical and spectroscopic analysis by X-ray photoelectron spectroscopy. The effect of scan rate and pH on the oxidation of pBPA film has been studied. The oxidation current was found to vary linearly with BPA concentration in the range 90–410 μM, and a detection limit of 55 μM was evaluated. Results of BPA amperometric detection have also been collected by using a repetitive potential step program to give a linear response to BPA in the concentration range 40–410 μM with a detection limit of 22 μM and a sensitivity of 1.57 μAμM^?1?cm^?2. The developed sensor showed satisfactory reproducibility and anti-interference properties and was successfully applied to BPA determination in mineral water samples.     

Ultrasensitive determination of hydrazine using a glassy carbon electrode modified with Pyrocatechol Violet electrodeposited on single walled carbon nanotubes

A glassy carbon electrode (GCE) was modified with pyrocatechol violet (PCV) that was electrodeposited on single walled carbon nanotubes (SWCNTs) via continuous cycling between 0 and 0.9 V (vs. SCE). The resulting electrode exhibits excellent electrocatalytic activity towards the oxidation of hydrazine at 0.3 V. The apparent surface coverage of the electrode is at least 24 times higher (2.7?×?10^?10 mol cm^?2) than that obtained with a bare GCE (1.1?×?10^?11 mol cm^?2). This is attributed to a remarkably strong synergistic effect between the acid-pretreated SWCNTs and the electrodeposited PCV coating. Response is fast (2 s) and sensitive (281 mA M^?1 cm^?2). Other features include a wide linear range (150 nM to 0.4 mM) and a low detection limit (150 nM at an SNR of 3). The sensor has been successfully applied to the determination of hydrazine in water and cigarette samples with good accuracy and precision. In addition, the morphology and the wetting properties of the coating were studied by scanning electromicroscopy and contact angle measurements.

Polyacrylamide-methanesulfonic acid gel polymer electrolytes for tin-air battery

The present work describes the synthesis and characterization of gel polymer electrolytes containing methanesulfonic acid (MSA) with Polyacrylamide (PAAm). The PAAm–MSA gel electrolytes were prepared with different concentrations of MSA. Addition of 0.5 M of MSA into the electrolyte increased the ionic conductivity of PAAm from 1.35 × 10^?3 to 1.56 × 10^?2 S cm^?1. The maximum ionic conductivity of 7.0 × 10^?1 S cm^?1 was obtained with 3 M MSA at room temperature. The chemical interaction between PAAm and MSA was studied by Fourier transformed infra-red. The performance as a polymer electrolyte was evaluated from the cell discharge and open circuit potential measurements of a tin-air cell. The tin-air cell supported relatively high current, up to 12 mA cm^?2 with a maximum power density of 5 mW cm^?2. The open-circuit potential of the cell was 1.27 V for 24 h.     

Rate constants for the gas-phase reactions of O3 with a series of carbonyls at 296 K

Rate constants for the gas-phase reactions of O₃ with the carbonyls acrolein, crotonaldehyde, methacrolein, methylvinylketone, 3-penten-2-one, 2-cyclohexen-1-one, acetaldehyde, and methylglyoxal have been determined at 296 ± 2 K. The rate constants ranged from <6 × 10^?21 cm³ molecule^?1 s^?1 for acetaldehyde to 2.13 × 10^?17 cm³ molecule^?1 s^?1 for 3-penten-2-one. The substituent effects of ? CHO and CH₃CO? groups on the rate constants are assessed and discussed, as are implications for the atmospheric chemistry of the natural hydrocarbon isoprene.     

Spectrophotometric analysis of trichloroethylene in various environmental and biological samples

A simple sensitive extractive spectrophotometric method for determination of trichloroethylene is proposed. Trichloroethylene is treated with pyridine to form glutaconic aldehyde by heterolytic cleavage of the pyridine ring. Glutaconic aldehyde is further coupled with 4-aminoacetanilide to form an orange–red dye which is extractable in 3-methyl-1-butanol. The extracted dye shows absorption maximum at 520 nm. The system obeys Beer’s law in the range of 0.05–0.8 μg mL^?1. Important analytical parameters such as time, temperature, reagent concentration, acidity etc. have been optimized for complete colour reaction. Sandell’s sensitivity and molar absorptivity for the system were found to be 0.001 μg cm^?2 and 1.2 × 10⁵ L mol^?1 cm^?1, respectively. The proposed method is satisfactorily applied to micro-level determination of trichloroethylene in various environmental and biological samples.     

Nitric acid oxidation of ordered mesoporous carbons for use in electrochemical supercapacitors

Ordered mesoporous carbon materials with high microporosity were synthesized by a low temperature autoclaving of citric acid-catalyzed polymerized resorcinol/formaldehyde in the presence of the triblock copolymer F127 and were activated by nitric acid oxidation. The materials were used as electrode materials in electrochemical supercapacitors. A bimodal pore size distribution of 2.1–2.3 and 5.3 nm with a surface area of 465–578 m² g^?1 and pore volume of 0.44–0.54 cm³ g^?1 was obtained with the retention of an ordered mesoporous structure after nitric acid (2 M) treatment. The introduced functional groups produced a pseudocapacitance, which resulted in an increase in the specific capacitance. The electrochemical capacitance of the resulting mesoporous carbons showed a marked increase after 3 h of nitric acid activation, exhibiting a high value of 295 F g^?1 at the scan rate of 10 mV s^?1 in 6 M KOH aqueous solution and good cycling stability with specific capacitance retention over 500 cycles.     

Pd black decorated by Pt sub-monolayers as an electrocatalyst for the HCOOH oxidation

Pd black was modified by a very low amount of Pt corresponding to a sub-monolayer (ML). Spontaneous displacement method was employed. The catalysts with 0.02–0.12 ML were characterized by cyclic voltammetry and CO_ads stripping and were tested for HCOOH oxidation under the potentiodynamic and potentiostatic conditions. All the Pt@Pd catalysts were more active for HCOOH oxidation than Pd black. The Pt@Pd with 0.08 ML of Pt exhibited the highest activity with the maximum current density under the potentiodynamic conditions of 8 mA cm^?2 (vs. 2.7 mA cm^?2 on Pd black). Contrasting HCOOH oxidation kinetics on Pt@Pd and Pt@Au catalysts revealed that the current densities are higher, and the poisoning rate is lower on Pt@Pd catalyst. This was ascribed to an optimal strength of the Pt–adsorbate bond when Pt is supported on Pd and to a possible influence of the Pt atoms on the Pd substrate.     

Evaluation of gamma irradiation effect on physico-chemical properties of a mixed beverage based in soy milk and grape juice

The effects of the main operation variables on the electrochemical oxidation of simulated tributyl phosphate (TBP) waste by a boron-doped diamond anode are individually studied. The optimum operating conditions are obtained as follows: 4 g L^?1 initial TBP concentration, 180 min degradation time, 40 mA cm^?2 current density, 0.5 mol L^?1 Na₂SO₄ as the supporting electrolyte, and unadjusted pH of the aqueous phase. Under such conditions, a chemical oxygen demand (COD) removal ratio of 82.3% is achieved, and the energy consumption is 26.16 kWh m^?3. A degradation mechanism of TBP is tentatively proposed.