Differential pulse polarographic determination of selenium(IV) in whole blood using the catalytic hydrogen wave

The selenium content in blood was determined using the hydrogen catalytic peak. This peak at -1.1 V was obtained in the presence of selenium and molybdenum at pH values of 1-4 in different buffers. For the determination of selenium, the Mo(VI) concentration has to be approximately 100-200 times higher than the selenium present. The linear domain range of selenium is 1x10(-6)-5x10(-9) M. The interference of zinc is eliminated by the addition of EDTA at pH 3.5 acetate buffer. The method was applied to 1.0 ml of digested blood, and 620+/-44 mug l(-1) Se and 7.15 mg l(-1) Zn could be determined with a 90% (n=6) confidence interval.     

Differential pulse polarographic determination of trace selenium(IV) and molybdenum(VI) using the catalytic hydrogen wave

In the presence of selenium(IV) and molybdenum(VI) a new polarographic peak appears which corresponds to a hydrogen catalytic wave. By differential pulse polarography a single, sharp peak at about -1.1 V is obtained, allowing trace determination of selenium(IV) and molybdenum(VI) in the range 1x10(-6)-5.0x10(-9) M with a linear calibration and a detection limit of 1.5x10(-9) M. The optimum conditions are found to be 0.1 M KNO(3) and a pH of about 3.2 (Britton-Robinson buffer). There is no serious interference from some ions when present at 1.0-40 times that of molybdenum. At higher amounts of interfering ions the interference is eliminated by the addition of EDTA.     

Separation of selenium(IV) and tellurium(IV) from mixtures by extraction chromatography with trioctylphosphine oxide

The reversed-phase extraction chromatographic separation of selenium(IV) and tellurium(IV) from several elements with trioctylphosphine oxide as extractant is reported. Selenium was extracted from 6M hydrochloric acid containing 7M lithium chloride was stripped with 4M hydrochloric acid, and tellurium was extracted from either the same medium as selenium or from 4M hydrochloric acid, and stripped with 1-2M hydrochloric acid. Selenium and tellurium can be separated from multicomponent mixtures.     

Determination of selenium(IV) by anodic stripping voltammetry with an in situ gold-plated rotating glassy carbon disk electrode

The application of an in situ gold-plated glassy carbon disk electrode to the determination of selenium(IV) by anodic stripping voltammetry is described. A single anodic stripping peak is obtained for solutions containing less than 1 × 10^-6 M Se(IV). The minimum concentration detected was 2 × 10^-9 M Se(IV). The determination of selenium in NBS SRM 1577 (Bovine Liver) by anodic stripping voltammetry with an in situ goldplated rotating glassy carbon electrode yielded a value of 1.14 ± 0.07 μg Se g^-1 compared with a certificate value of 1.1 ± 0.1 μg Se g^-1.     

Determination of selenium and tellurium in air by atomic-absorption spectrometry

Elemental selenium and tellurium, and gaseous inorganic forms of Se(IV), Se(VI), Te(IV) and Te(VI) have been determined after their adsorption on gold-coated beads. After leaching, with water and dilute hydrochloric and nitric acids, the different chemical species in each acid fraction were separated with an anion-exchange resin (Bio-Rad AG-1X8) and a cation-exchange resin (Amberlite IR-120 Plus) by varying the acidity of the leaching agent. Subsequent analysis was by graphite-fumace atomic-absorption spectrometry. The lower detection limit for Se and Te was 0.03 ng/M(3) with a precision of +/- 5%. The average amounts of selenium in interior and exterior air samples were about 4.73 and 1.93 ng/m(3) respectively. For tellurium the corresponding values were about 0.78 and 0.24 ng/m(3).     

Determination of trace amount of oxalic acid with zirconium(IV)-(DBS-arsenazo) by spectrophotometry

A novel method is proposed for the determination of trace amount of oxalic acid in the present article. In 1.0M hydrochloric acid medium, oxalic acid can react with the zirconium(IV) in Zr(IV)-(DBS-arsenazo) complex and replaces the DBS-arsenazo to produce a hyperchromic effect at 520 nm. The hyperchromic degree is proportional to the concentration of the oxalic acid added over a defined range. Based on this property, a new method for the spectrophotometric determination of trace oxalic acid was developed. Beer's law is held over the concentration range of 9.0 x 10(-6) to 5.0 x 10(-4)M for oxalic acid with a correlation coefficient of 0.9995. The apparent molar absorptivity of the method is epsilon520 nm = 1.16 x 10(3)L mol(-1)cm(-1) and the detection limit for oxalic acid is 0.815 microg/mL. The developed method was directly applied to the determination of oxalic acid in tomato samples with satisfactory results.     

Synthesis and characterization of copper-, zinc-, manganese-, and cobalt-substituted dimeric heteropolyanions, [(alpha-XW9O33)2M3(H2O)3](n-) (n = 12, X =As(III), Sb(III), M = Cu(2+), Zn(2+); n = 10, X = Se(IV), Te(IV), M = Cu(2+) and [(alpha-AsW9O33)2WO(H2O)M2(H2O)2](10-) (M = Zn(2+), Mn(2+), Co(2+)

Interaction of the lacunary [alpha-XW9O33](9-) (X = As(III), Sb(III)) with Cu(2+) and Zn(2+) ions in neutral, aqueous medium leads to the formation of dimeric polyoxoanions, [(alpha-XW9O33)2M3(H2O)3](12-) (M = Cu(2+), Zn(2+); X = As(III), Sb(III)), in high yield. The selenium and tellurium analogues of the copper-containing heteropolyanions are also reported: [(alpha-XW9O33)2Cu3(H2O)3](10-) (X = Se(IV), Te(IV)). The polyanions consist of two [alpha-XW9O33] units joined by three equivalent Cu(2+) (X = As, Sb, Se, Te) or Zn(2+) (X = As, Sb) ions. All copper and zinc ions have one terminal water molecule resulting in square-pyramidal coordination geometry. Therefore, the title anions have idealized D3h symmetry. The space between the three transition metal ions is occupied by three sodium ions (M = Cu(2+), Zn(2+); X = As(III), Sb(III)) or potassium ions (M = Cu(2+); X = Se(IV), Te(IV)) leading to a central belt of six metal atoms alternating in position. Reaction of [alpha-AsW9O33](9-) with Zn(2+), Co(2+), and Mn(2+) ions in acidic medium (pH = 4-5) results in the same structural type but with a lower degree of transition-metal substitution, [(alpha-AsW9O33)2WO(H2O)M2(H2O)2](10-) (M = Zn(2+), Co(2+), Mn(2+)). All nine compounds are characterized by single-crystal X-ray diffraction, IR spectroscopy, and elemental analysis. The solution properties of [(alpha-XW9O33)2Zn3(H2O)3](12-) (X = As(III), Sb(III)) were also studied by 183W-NMR spectroscopy.     

Selective extraction-photometric redox determination of low concentrations of sulfur(IV), selenium(IV), tellurium(IV), and arsenic(III)

A procedure is proposed for the selective extraction-photometric determination of the acid-forming elements S(IV), Se(IV), Te(IV), and As(III) in their mixtures containing molecular forms or anions with different electron densities on donor atoms. The procedure is based on the difference in the oxidizability of analytes with the [SbCl₆]^? complex. The analytical ranges are found at different pHs of the medium, affecting the potential of the two-phase redox systems. The detection limits for sulfite, selenite, tellurite, and arsenite are 1 × 10^?3, 5 × 10^?5, 7 × 10^?5, and 1 μg/mL, respectively. The procedure is applied to the determination of selenium in H₂SO₄ of high-purity grade, which is used in the production of microelectronics items and in some agricultural samples. The error of analysis is no worse than 20%.     

Indirect spectrophotometric determination of small amounts of selenium(IV) and arsenic(V) by simple extraction using flotation columns.

A simple, rapid and selective procedure for the indirect spectrophotometric determination of Se(IV) and As(V) has been developed. It is based on the reduction of Se(IV) to Se(0) and As(V) to As(III) with hydroiodic acid (KI + HCl). The liberated iodine, equivalent to each analyte, is quantitatively extracted with oleic acid (HOL) surfactant. The iodine-HOL system exhibits its maximum absorbance at 435 nm. The different analytical parameters affecting the extraction and determination processes have been examined. The calibration graphs were found to be linear over the ranges 5-120 and 0.25-20 ppm of Se(IV) and As(V), with lower detection limits of 2.5 and 0.15 ppm and molar absorptivities of 1 x 10(4) and 0.5 x 10(4) dm3 mol(-1) cm(-1), respectively. Sandell's sensitivity was calculated to be 0.0078 and 0.0149 microg/cm2 in the same order. The relative standard deviation for five replicate analyses of 40 ppm Se(IV) and 4 ppm As(V) were 1.0 and 0.9%, respectively. The proposed procedure in the presence of EDTA as a masking agent for foreign ions has been successfully applied to the determination of Se(IV) in a reference sample and As(V) in copper metal, in addition to their determination in spiked and polluted water samples.     

Anion-exchange separation of Te(IV) from Te(VI), Se(IV) and Se(VI) on deae-cellulose in mixed hydrochloric-acetic acid media

Te(IV) can be separated from Te(VI), Se(IV) and Se(VI) by adsorption of Te(IV) on a DEAE-cellulose column from a mixed 1M hydrochloric acid-acetic acid solution (1:9, v/v). This allows a selective separation of Te (IV) from the other three species in widely different mole ratios.     

A highly sensitive colour reaction for Se(IV) with the iodide-rhodamine B-PVA system Spectrophotometric determination of trace amounts of selenium in water

A highly sensitive spectrophotometric method for determination of selenium(IV) has been developed, based on Se(IV) oxidation of I(-) to I(-)(3) in a weak-acid medium, then formation of the 1:1 ion-association complex of I(-)(3) with Rhodamine B in the presence of poly(vinyl alcohol). The molar absorptivity is 1.97 x 10(5)l.mole(-1).cm(-1). Preconcentration of Se(IV) and elimination of interfering ions is achieved by an improved thiol cotton method, so the determination has very good selectivity. Se(IV) at mug/l. levels in tap water, hot-spring water and river water has been satisfactorily determined by the method.     

Selective collection of selenium(IV) on anion-exchange resin with azothiopyrine disulphonic acid

Azothiopyrine disulphonic acid (ATPS) has been shown to be terfunctional, namely it can form a selenotrisulphide by reaction of its thiol group with selenium(IV), bind to an anion-exchange resin by ion-exchange through its sulphonate group, and be strongly physically adsorbed on the ion-exchange resin, ATPS adsorbed on the resin does not bleed into solution even in the presence of sodium chloride and hydrochloric acid. The collection of seleniurn(IV) is practically complete when ATPS is added to a selenium(IV) solution and the reaction product is collected on the anion-exchange resin. Selenium(IV) is not satisfactorily collected, however, by reaction with anion-exchange resin loaded with ATPS. The sorbed selenium can be eluted [as Se(IV)] with 13M nitric acid and directly determined fluorometrically in the eluate.     

Determination of Selenium(IV) by Stripping Voltammetry at a Mercury-Film Electrode

A procedure was proposed for the determination of selenium(IV) by stripping voltammetry on a mercury-film electrode at an electrolysis potential of +0.4 V versus the saturated silver–silver chloride reference electrode in a 1 M H₂SO₄ solution. The current of the cathodic peak is a linear function of the selenium(IV) concentration in the range from 5 × 10^–3 to 3 × 10^–1 mg/L (6.3 × 10^–8 to 3.8 × 10^–6 M) at a time of electrolysis of 30 s (t _el). The detection limit for selenium is 1 × 10^–4 mg/L (1.3 × 10^–9 M) at t _el = 300 s. It was shown that selenium(IV) can be determined in the presence of 10 mg/L Zn(II), 1 mg/L Cd(II), 0.5 mg/L Pb(II), and 0.2 mg/L Cu(II). A procedure for the determination of selenium in natural, mineral, and potable water was proposed.     

Synthesis, structure, and thermal properties of soluble hydrazinium germanium(IV) and tin(IV) selenide salts

The crystal structures of two hydrazinium-based germanium(IV) and tin(IV) selenide salts are determined. (N(2)H(5))(4)Ge(2)Se(6) (1) [I4(1)cd, a = 12.708(1) Angstroms, c = 21.955(2) Angstroms, Z = 8] and (N(2)H(4))(3)(N(2)H(5))(4)Sn(2)Se(6) (2) [P, a = 6.6475(6) Angstroms, b = 9.5474(9) Angstroms, c = 9.8830(10) Angstroms, alpha = 94.110(2) degrees, beta = 99.429(2) degrees, gamma = 104.141(2) degrees, Z = 1] each consist of anionic dimers of edge-sharing metal selenide tetrahedra, M(2)Se(6)(4-) (M = Ge or Sn), separated by hydrazinium cations and, for 2, additional neutral hydrazine molecules. Substantial hydrogen bonding exists among the hydrazine/hydrazinium molecules as well as between the hydrazinium cations and the selenide anions. Whereas the previously reported tin(IV) sulfide system, (N(2)H(5))(4)Sn(2)S(6), decomposes cleanly to microcrystalline SnS(2) when heated to 200 degrees C in an inert atmosphere, higher temperatures (>300 degrees C) are required to dissociate selenium from 1 and 2 for the analogous preparations of single-phase metal selenides. The metal chalcogenide salts are highly soluble in hydrazine, as well as in a variety of amines and DMSO, highlighting the potential usefulness of these compounds as precursors for the solution deposition of the corresponding metal chalcogenide films.     

Electroreduction of Tellurium(IV) on Solid Electrodes in Neutral Solutions

Electroreduction of Te(IV) on glassy-carbon and nickel in neutral and weakly alkaline solutions is studied by cyclic voltammetry. A wave for the Te(IV) Te(0) process is discovered. At a limiting current of Te(IV) reduction in a potentiodynamic mode in 0.5 M Na₂SO₄, a peak current is observed on Ni at –1.02 V (Ag/AgCl). The relationship between the peak and the tellurium electroreduction to the tellurium ion and the tellurohydrogen formation involving a proton is discussed. Dependence of the peak current on the concentration of Te(IV) ions is used for their analytical assay.     

Simultaneous determination of selenium and lead in whole blood samples by differential pulse polarography

The polarographic reduction of lead in the presence of selenite gives rise to an additional peak corresponding to the reduction of lead (Pb) on adsorbed selenium (Se) on mercury at −0.33 V. The selenium and lead content can be determined using this peak by the addition of a known amount of one of these ions first and then the second ion. The linear domain range of lead is 5.0×10⁻⁷–2.0×10⁻⁵ M and for selenium 5.0×10⁻⁷–1.0×10⁻⁵ M. Using this method 4.90×10⁻⁷ M Se(IV) and 1.47×10⁻⁶ M Pb(II) in a synthetic sample could be determined with a relative error of +2.0% and 1.8%, respectively (n=4). A recovery test after acid digestion for a synthetic sample was 97% for selenium and 96.5% for lead. The method was applied to 1 ml of digested blood, and 328±23 μg l⁻¹ Se(IV) and 850±62 μg l⁻¹ Pb(II) could be determined with a 90% (n=5) confidence interval.     

N-oxides of 4-(5-nonyl)pyridine and trioctylamine as extractants for cerium(IV) and its separation from thorium(IV)

Trace level cerium has been oxidized to the quadrivalent state with potassium dichromate and shown to be preferentially extracted from very dilute mineral acid solutions and also from moderate nitric acid media by 0.1M solutions of 4-(5-nonyl)pyridine oxide and trioctylamine oxide dissolved in xylene. The dependence of extraction on the type of N-oxide, acid concentration and the N-oxide concentration has been investigated. The influence of the concentration of salting-out agents is described. Separation factors for a number of metal ions relative to cerium(IV) are reported for 0.1 M 4-(5-nonyl)pyridine oxide/xylene-0.1M sulphuric acid system. The ratio of the D for Ce(IV) to that of Ce(III) is greater than 10⁵, and the D for Ce(IV) is much greater than that for thorium(IV). Separation of cerium(IV) from thorium has been achieved from 0.1M sulphuric acid solutions using 0.1M 4-(5-nonyl)pyridine oxide/xylene as an extractant.     

Differential pulse polarography of germanium(IV), tin(IV), arsenic(V), antimony(V), selenium(IV) and tellurium(VI) at the static mercury drop electrode in catechol—perchlorate media

The differential pulse polarography of Ge(IV), Sn(IV), As(V), Sb(V), Se(IV) and Te(VI) has been investigated in perchlorate media containing catechol using a static mercury drop electrode. Under optimum conditions, Ge(IV), Sn(IV), As(V), and Sb(V) undergo reduction to yield well-defined peaks; detection limits of 82 ppb, 28 ppb, 4 ppm, and 25 ppb, respectively, have been calculated. Few electrolytes are known for which these ions exhibit a quantitatively useful polarographic response. While Se(IV) and Te(VI) may be detected at levels of 115 ppb and 17 ppb, respectively, addition of catechol does not enhance the peak current relative to that observed in simple perchlorate solutions, as was the case for the other ions studied. The determination of germanium, arsenic and antimony in samples is described.     

Experimental and theoretical investigations of tellurium(IV) diimides and imidotelluroxanes: X-ray structures of B(C6F5)3 adducts of OTe(mu-NtBu)2TeNtBu, [OTe(mu-NtBu)2Te(mu-O)]2 and tBuNH2

The hydrolysis of (t)BuNTe(mu-N(t)Bu)(2)TeN(t)Bu (1) with 1 or 2 equiv of (C(6)F(5))(3)B.H(2)O results in the successive replacement of terminal imido groups by oxo ligands to give the telluroxane-Lewis acid adducts (C(6)F(5))(3)B.OTe(mu-N(t)Bu)(2)TeN(t)Bu (2) and [(C(6)F(5))(3)B.OTe(mu-N(t)Bu)(2)Te(mu-O)](2) (3), which were characterized by multinuclear NMR spectroscopy and X-ray crystallography. The Te=O distance in 2 is 1.870(2) A. The di-adduct 3 involves the association of four (t)()BuNTeO monomers to give a tetramer in which both terminal Te=O groups [d(TeO) = 1.866(3) A] are coordinated to B(C(6)F(5))(3). The central Te(2)O(2) ring in 3 is distinctly unsymmetrical [d(TeO) = 1.912(3) and 2.088(2) A]. The X-ray structure of (C(6)F(5))(3)B.NH(2)(t)()Bu (4), the byproduct of these hydrolysis reactions, is also reported. The geometries and energies of tellurium(IV) diimides and imido telluroxanes were determined using quantum chemical calculations. The calculated energies for the reactions E(NR)(2) + Te(NR)(2) (E = S, Se, Te; R = H, Me, (t)Bu, SiMe(3)) confirm that cyclodimerization of tellurium(IV) diimides is strongly exothermic. In the mixed-chalcogen systems, the cycloaddition is energetically favorable for the Se/Te combination. The calculated energies for the further oligomerization of the dimers XE(mu-NMe)(2)EX (E = Se, Te; X = NMe, O) indicate that the formation of tetramers is strongly exothermic for the tellurium systems but endothermic (X = NMe) or thermoneutral (X = O) for the selenium systems, consistent with experimental observations.     

Chemiluminescence of chlorpromazine hydrochloride based on cerium(IV) oxidation sensitized by rhodamine 6G

A new chemiluminescence (CL) method is proposed for the determination of chlorpromazine hydrochloride, a drug often used to treat the psychiatric patients suffering from clinical depression. The method is based on the reaction between studied drug and Ce(IV) in a nitric acid medium and measurement of the CL intensity produced by rhodamine 6G used as a sensitizer. In the optimum conditions, CL intensities are proportional to concentrations of the studied drug over the range 0-1x10(-5) g ml(-1) with a detection limit of 6.5x10(-9) g ml(-1). The relative standard deviation (R.S.D.) is 4.1% for 1.5x10(-6) g ml(-1) chlorpromazine hydrochloride (n=11). The method has been applied to the determination of studied drug in tablets and biological fluids with satisfactory results.