Determination of indium in high purity antimony by electrothermal atomic absorption spectrometry (ETAAS) using boric acid as a modifier

The use of boric acid as a modifier for the determination of trace amount of indium in high purity antimony by electrothermal atomic absorption is described. It was found that the negative influence of the hydrofluoric acid, used for the digestion could not be eliminated by using stabilized temperature platform furnace (STPF) alone. Due to the high dissociation energy (D₀ = 506 kJ mol⁻¹) of indium fluoride, it is difficult to dissociate in the gas phase and hence is lost. In presence of HF (used for the dissolution of antimony), the universal Pd-Mg modifier does not work satisfactorily. Additionally, rising corrosion and reduced tube lifetime were observed when the acid digested (HF-HNO₃) antimony solution was injected in to the platform. Improvement in platform life and elimination of interferences were achieved by the addition of boric acid as a chemical modifier together with ruthenium coating of the platform. Corrosive changes of the transversely heated graphite atomizer (THGA) platform surface were examined by scanning electron microscopy. The standard addition method was applied. A characteristic mass of 36 pg was obtained. The detection limit of the proposed method is around 0.04 μg g⁻¹. The developed method was applied to the determination of indium in real samples. The data obtained by this method were in good agreement with those obtained by ICP-MS.     

Critical study of the determination of tin by electrothermal atomic-absorption spectrometry using resonance and non-resonance lines

The 235.48 nm non-resonance line of tin gives a sensitivity for AAS determination equal to that given by the most sensitive resonance line. Vaporization from a platform improves some twofold the sensitivities of all lines investigated. The atomization temperature has only slight influence on the relative sensitivities given by the non-resonance tin lines studied. Phosphoric acid shows a rather peculiar interference pattern, low concentrations (0.05%) depressing the signal, but high concentrations (1%) enhancing it. Contrary to expectation, the resonance and non-resonance lines are affected to the same extent by phosphoric acid. Platform-vaporization does not change the interference pattern of phosphoric acid. Calibration can be done by injecting various volumes of a single standard solution onto a platform coated with tantalum carbide. This method yields calibration graphs that are just as linear as those obtained with identical volume of standards of various concentrations. Some suggestions are made for further improvement of the analytical potential of non-resonance lines.     

Determination of traces of rubidium in high purity cesium chloride by electrothermal atomic absorption spectrometry (ETAAS) using boric acid as a modifier

The use of boric acid as a modifier for the determination of trace amount of rubidium in high purity cesium chloride matrix by electrothermal atomic absorption is described. It was found that the negative influence of the chloride matrix could not be eliminated using stabilized temperature platform (STPF) alone. Due to the high dissociation energy (D₀ = 427 kJ mol⁻¹) of rubidium chloride, it was difficult to dissociate in the gas phase and hence is lost. Elimination of interferences was achieved by the addition of boric acid as a chemical modifier. Diluted cesium chloride samples (5%, m/v) were analyzed applying the standard addition method. The characteristic mass of 24 pg was obtained. The detection limit of the proposed method is around 26 ng g⁻¹. The developed method was applied to the determination of traces of rubidium in high purity cesium chloride samples. The data obtained by this method were in good agreement with those obtained by other independent method like FAAS.     

Silicon determination in milk by electrothermal atomic absorption spectrometry using palladium as chemical modifier

A direct method for silicon determination in milk samples by Electrothermal Atomic Absorption Spectrometry was developed. Palladium was used as chemical modifier at a concentration of 610 mg L(-1); with this modifier, silicon was stable up to 1800 degrees C. The precision and accuracy of the method were investigated. The detection limit was 16.2, 2.7 and 7.2 micro g L(-1) for cows' milk, human milk and infant formula, respectively. The method was applied to silicon determination in 17 infant formula samples, 13 human milk samples and 12 cows' milk samples.     

A rapid hydride-evolution electrothermal atomic-absorption method for the determination of tin in geological materials

A rapid, semi-automated electrothermal atomic-absorption spectrophotometric method involving lithium metaborate fusion and hydride evolution has been developed for the determination of tin in geological materials. The sample is fused with lithium metaborate and brought into solution with hydrochloric acid: the tin in the solution is then converted into its hydride with sodium borohydride in an autosampler. The hydride is decomposed and atomized in an electrically heated quartz furnace, and the atomic absorption of tin at 286.3 nm is measured. The detection limit and the linear working range for tin are 1 ng/ml and 0-140 ng/ml respectively. The method has wide tolerance for variation in reagent concentrations and possible interferences, and when tested on some certified rocks and soils having a wide range of tin values, was found to be satisfactorily accurate and precise. The procedure is now used routinely in our laboratories. At least 10-12 samples can be analysed per hour.     

Investigations for the determination of tin by flow injection hydride generation atomic-absorption spectrometry

It could be shown that the pre- or double peaks which are frequently observed in the determination of tin by hydride generation atomic-absorption spectrometry are not due to reagent contamination or memory effects. Rather they originate from the silica material used to make the quartz tube atomizer. At elevated temperatures the tin diffuses to the surface and it can be volatilized and atomized only in the presence of hydrogen. The height of the pre-peak depends, among other things, on the time for which the quartz tube atomizer has been at a high temperature without hydrogen. The pre-peaks disappear when argon with 10% (v/v) hydrogen is used as the purge gas. In flow injection the pre-peaks can be separated in time from the analytical signal by using a program in which hydrogen is generated by reaction of sodium tetrahydroborate reluctant solution with the acid carrier prior to the injection of the sample. Also investigated was the influence of the acid and sodium tetrahydroborate concentration on sensitivity and freedom from interferences. Best results were obtained when a saturated boric acid solution containing 0.1M hydrochloric acid was used for standards, samples and carrier solution, and a 0.4% (m/v) sodium tetrahydroborate solution with 0.05% (m/v) sodium hydroxide as the reluctant. Under these conditions tin could be determined accurately in the range 0.008-0.1% in low alloy steel standard reference materials, with matrix-free standard solutions for calibration.     

Determination of tin in marine sediment slurries by electrothermal atomic absorption spectrometry using palladium-magnesium nitrate as chemical modifier

 A method was optimized for the determination of tin in slurries of marine sediment samples using palladium-magnesium nitrate as chemical modifier and Triton X-100 (0.1%) surfactant as stabilizer. To obtain a complete pyrolysis of the slurry sample, two charring steps were used, the first at 480 °C and the second at 1300 °C. The precision and accuracy of the method were studied using the Reference Material PACS-1 (marine sediment) from National Research Council Canada. The detection limit (LOD) was 57.6 μg kg^-1. The method was applied to the determination of tin in marine sediment samples from the Galicia coast. Received: 16 February 1996/Revised: 26 March 1996/Accepted: 12 April 1996     

Semi-permanent lutetium modifier for the determination of beryllium in urine by electrothermal atomic absorption spectrometry

The determination of beryllium using electrothermal atomic absorption spectrometry with deuterium background correction in the presence of various isomorphous metals and Mg(NO₃)₂ was studied. While, Eu, Ir and Sm had no effect on the transient signals, the addition of Lu and Mg(NO₃)₂ improved the sensitivity of the beryllium signal with respect to that obtained in the absence of modifier. Although, Mg(NO₃)₂ has improved the signal with respect to its sensitivity, it also increased the tail and the background (BG) signals, specially when urine samples are under study. Whereas, when Lu was used the analytical signal is virtually free of BG interference indicating that the urine matrix interference was almost eliminated. Besides, the addition of 6 μg of Lu ensured that the signals were effectively constant for five firings following the furnace program, which included: three drying, and the pyrolysis, atomization, cleaning and cooling steps. The effect of some components, likely to interfere in the accurate determination of beryllium (such as: Al, Ca, Cl, Co, Cr, Fe, Mg and Mn) were investigated. At the physiological levels, most of these elements had no effect, except in the case of chloride when Mg(NO₃)₂ was used as modifier. In this case, the tolerance limit was of 3000 mg Cl⁻ l⁻¹. The characteristic masses were 1.19, 0.45 and 0.48 pg, when integrated absorbance was measured for beryllium without the addition of any modifier and in the presence of Lu and Mg(NO₃)₂, respectively. The limits of detection (3σ) were 85, 19 and 58 fg, respectively. The accuracy and precision with the use of Lu and Mg(NO₃)₂ was tested for the direct determination of beryllium in urine samples. Quantification was performed with aqueous standards. The results obtained for the determination of beryllium in reference materials (Trace Elements in Urine), together with good recovery of spiked analyte, using either Lu or Mg(NO₃)₂ modification demonstrate the applicability of the procedure to the analysis of real samples. However, Lu provided the most accurate results. Also, the addition of Lu enhanced the precision of the measurements to levels of 1.8% relative standard deviation instead of 5.6 and 3.3% for the case of beryllium alone and with the addition of Mg(NO₃)₂.     

Development of a slurry atomization method for the determination of cadmium in food samples by electrothermal atomization atomic-absorption spectrometry

Matrix modifiers have been compared for the determination of cadmium in foodstuffs by ETA-AAS with the sample injected in the form of a slurry. Addition of 800 mug/ml Pd stabilized cadmium to a similar extent as did ammonium dihydrogen phosphate, but avoided the increase in background signal associated with the latter. An analytical procedure was developed, based on palladium matrix modification, platform atomization with a pre-atomization cooling step and integrated absorbance measurements. The method allowed the analysis of milk, liver and olive leaf slurries at concentrations up to at least 50 mg/ml by direct calibration with aqueous standards. The accuracy of the analytical results was within 15% and the detection limit for cadmium in analysis of a 50 mg/ml slurry was 10 ng/g.     

Direct analysis of coal by electrothermal atomization atomic-absorption spectrometry

A novel approach for trace element determination in coal samples is described, based on grinding the sample to less than 200 mesh, "pipetting" the material into a tube-cup furnace, and measurement by electrothermal atomization atomic-absorption spectrometry. Either solid standard reference materials or aliquots of solutions of Pb, Zn and Mn can be used to prepare analytical calibration curves. The SRMs are diluted with spectroscopic grade graphite prior to introduction into the tube-cup furnace. After the atomization and cleaning step, any remaining ash is removed with a Pasteur pipette. The measured values for Pb, Zn and Mn agree well with the certified SRM values. The method is rapid, and sufficiently precise (5-14%) and accurate (within 5-12% of standard reference values).     

Use of complexing ligands in the determination of antimony and tin by atomic-absorption spectrometry

The atomic-absorption spectrophotometric determination of antimony is best achieved in the presence of either an ammonium fluoride, hydrochloric acid, nitric acid mixture, or one of the following complexing agents: tartaric acid, citric acid, oxalic acid, 2-mercaptopropanoic acid. The interference of the 29 metals tested is least in the ammonium fluoride-hydrochloric acid-nitric acid mixture and is similar in tartaric acid, citric acid and 2-mercaptopropanoic acid media. However, the interference is pronounced in oxalic acid. Tin can be determined if any of the complexing agents or 6M hydrochloric acid is present.     

Direct determination of cadmium in calcium drug samples using electrothermal atomic absorption spectrometry with a metal tube atomizer and thiourea as a matrix modifier

A laboratory constructed molybdenum tube atomizer was used for direct determination of trace cadmium in drug samples by the electrothermal atomic absorption spectrometric (ETAAS) method. An ultrasonic agitation method for a solution including the sample powder was used. A calibration curve was constructed with a cadmium standard solution including matrix. To eliminate interference from other matrix elements, a chemical modifier thiourea, was used. The detection limit were 17 pg ml(-1) (3 S/N), and the RSD of the direct analysis was 5-17%. The results for cadmium in the four drug samples analysed by the direct ETAAS method matched well with those obtained with nitric acid digested samples. The recovery of added cadmium was 103-106%. An accurate method is elaborated for the determination of cadmium in drug samples by direct ETAAS techniques. The merits of this method are rapid calibration, simplicity, fast analysis, and low cost.     

Determination of tin in marine sediments by slurry sampling atomic absorption spectrometry with electrothermal atomization using a permanent modifier

A molecularly imprinted polymer (MIP) was synthesized by the precipitation polymerization method using triazophos (TAP) as the template. The MIP can selectively absorb TAP from sample solutions. The absorbed TAP strongly enhances the chemiluminescence (CL) of luminol-H₂O₂. This was applied to design a method for the on-line enrichment and detection of TAP. The change in CL intensity is linearly proportional to the concentration of TAP in the range from 1.0 μM to ~4.0 nM, and the detection limit is 2.5 nM (at an S/N of 3σ). This is about one order of magnitude lower than that of the conventional CL assay. The method was successfully applied to the determination of TAP in vegetable samples.     

Effectiveness of palladium as a chemical modifier for direct silver and manganese determination in cocaine and heroin by electrothermal atomic absorption spectrometry

Methods for the direct determination of silver and manganese in cocaine and heroin by electrothermal atomic absorption spectrometry using palladium as chemical modifier have been developed. Cocaine samples, 0.5 g, were dissolved in 2 ml of 35.0% (m/v), HNO(3) diluting to 10 ml with ultrapure water. A comparative study of palladium, magnesium nitrate, palladium-magnesium nitrate and nitric acid used as chemical modifiers was carried out, and it was found that palladium alone is adequate to stabilize silver and manganese at charring temperatures of 1000 and 1300 degrees C respectively. A study was made on the insertion of a cooling step before the atomization step, and this approach was not advantageous. Limits of detection of 2.3 and 6.9 microg kg(-1) were obtained for silver and manganese respectively. The analytical recovery oscillated between 95.9 and 103.6% for silver and between 99.7 and 103.0% for manganese. Finally, a study of some interferences and a study of the precision and analytical recovery of the amount of sample were also carried out.     

Direct determination of aluminium in serum and urine by electrothermal atomic absorption spectrometry using ruthenium as permanent modifier

Ruthenium (Ru), thermally deposited on a integrated platform graphite furnace, was investigated as a permanent modifier for the determination of Aluminum (Al) in blood serum and urine by electrothermal atomic absorption spectrometry (ETAAS). The platform was treated with 500 μg of Ru as previously described. The pyrolysis and atomization temperatures for each material were of 1300 and 2300 °C, for serum sample and of 1000 and 2400 °C, for urine. The characteristic mass were of 31 and 33 pg for Al in serum sample and urine, respectively (recommended of 31 pg for Al in nitric acid 0.2% (v/v)). For this reason, the calibration was made with aqueous solutions for both the samples. Calibration curves presented r of 0.99145 and 0.99991 for serum and urine, respectively. With the optimized temperatures, being analyzed eight spiked blood serum samples, the recovery was between 95.90 and 113.50%. Two certified urines samples were analyzed with good agreement between experimental and reference values. In both the samples the R.S.D. were <5% (n=3). The detection limit (k=3, n=10) was of 0.40 μg of Al per liter for both the samples. The absorption pulses obtained were symmetrical, with very low background and without interferences. The life time of the tube-platform was higher than 600 cycles of atomizations for both the urine and serum samples.     

A fast method for the determination of lead in paprika by electrothermal atomic-absorption spectrometry with slurry sample introduction

A rapid procedure for the determination of lead in commercial paprika samples is described. The samples are first calcined at 350 degrees , then suspensions are prepared in water containing 0.1% v/v Triton X-100 and 0.1% w/v ammonium phosphate and injected into the electrothermal atomiser. The use of platform atomisation with a preatomisation cooling step allows for simple calibration with aqueous standards. When using 0.4% suspensions the detection limit is 0.2 ug/g. The results for seven paprika samples agree with those obtained by an alternative method involving calcination and dissolution in acid.     

Direct determination of beryllium, copper and zinc in AlU matrices by electrothermal atomization atomic-absorption spectrometry

An atomic-absorption spectrometric method with electrothermal mode of atomization has been developed for the direct determination of Be, Cu and Zn in AlU (3:1) matrix samples without prior chemical separation of the major matrix. The studies carried out include the effect of the matrix on the analyte absorbance, optimization of sample aliquot and other experimental parameters, and analysis of a number of synthetic samples. Nanogram amounts of the analytes can be determined with a solution aliquot of 5 microlitres containing 25 micrograms of the sample with a precision of 6% or better. The analytical range obtained for these analytes is Be: 2-20 mug/l., Cu: 20-200mug/l. and Zn: 1-40mug/ml in the AlU matrix. The analysis of synthetic samples has shown good agreement with their added contents.     

Iridium as permanent modifier in the determination of lead in whole blood and urine by electrothermal atomic absorption spectrometry

The behavior of Iridium as a thermally deposited permanent modifier for the determination of lead by GFAAS was studied. The iridium coating procedure was optimized using a two-level factorial design. Using the optimized coating procedure, up to 1100 firings were possible with the same coating without sensitivity losses. The system was used in the determination of lead in whole blood and urine. A mixture of 0.1% Triton X-100 and 0.2% nitric acid was used as diluent. Pyrolysis temperature was 800°C for both matrices. Spiked, low-level samples were used for calibration. Under these conditions, no significant difference was found in comparison to the results obtained using a validated conventional modification procedure employing phosphate as modifier. Also, good agreement between found and certified/reference values were observed in the analysis of certified and commercial quality control materials, respectively. Such agreement was observed even using a 1100 times fired Ir coated platform–graphite tube assembly.