A sulpha-drug sensitive sensor based on ion-pair complex modified PQC resonator

The construction and general performance characteristics of the piezoelectric sensors responsive to sulpha-drug are described here. The proposed sensing method is based on the use of the ion-pair complex of sulphadiazine-cetyltrioctylammonium. The complex, together with cholestyramine was embedded in PVC matrix. This sensor exhibited reasonable selectivity and a sensitive mass response to sulpha-drugs. The response range of the sensor was between 1.0x10(-7) and 1.0x10(-5) M with a detection limit of 8x10(-8) M at pH 8.63. The influencing factors were investigated in detail and optimized.     

A conductance sensor for dissolved sulphur dioxide using a series piezoelectric crystal device

A new piezoelectric crystal impedance sensor for the determination of sulphur dioxide in aqueous solution is presented. It is realized using a series piezoelectric crystal device which is constructed by connecting an AT-cut piezoelectric crystal to a probe in series. The probe is filled with an internal electrolyte solution that is separated from sample solutions by a gas-permeable membrane. The present sensor exhibits a favourable frequency response to 1 x 10(-7)-1 x 10(-3) M sulphur dioxide. The detection limit is 1 x 10(-8) M. The effects of the sensor preparation are considered. Dynamic range, reproducibility, response time and selectivity of the sensor are also discussed. The proposed sensor has been used successfully for lamp sulphur determinations in petroleum samples.     

A sensitive and specific method for isoniazid determination based on selective adsorption using an isoniazid ion-selective piezoelectric sensor

A selective, sensitive and simple ion-selective piezoelectric (ISP) sensor was developed for the direct determination of isoniazid (INH) in body fluids. Based on sensitive mass response of piezoelectric quartz crystal and selective adsorption/desorption across the modified film, the ISP sensor was fabricated by coating a PVC film containing activant on one electrode of a thickness-shear mode piezoelectric quartz crystal. The observed frequencies of ISP sensor were found to decrease with the increase of the INH concentration in a 0.1 M NaNO(3) solution. In this paper, three activants, INH-phosphotungstate (I), INH-silicotungstate (II), and INH-[BiI(4)](-) (III), were synthesized and investigated. Calibration graphs were linear from 6x10(-8) to 2x10(-3) M for I, 2x10(-7) to 2x10(-3) M for II and 2x10(-7) to 2x10(-3) M for III, with detection limits 6x10(-8) M for I, 2x10(-7) M for II and 2x10(-7) M for III, in a 0.1 M NaNO(3) solution at pH 7.0 and 37 degrees C. Recoveries were from 98% to 102% with R.S.D. up to 2%. Results for real samples obtained by the proposed method agreed well with those obtained by the conventional pharmacopeia method.     

Construction and application of phenytoin anion-selective electrode based on bulk acoustic wave (BAW) sensing technique

This paper describes the construction of an anion-selective bulk acoustic wave (BAW) sensor for the direct determination of phenytoin sodium for the first time. Based on the sensitive mass response of a piezoelectric quartz crystal (PQC) and selective adsorption-desorption across the modified film, the BAW sensor was fabricated by coating a polyvinylchloride (PVC) film containing activator on one side of a PQC. The method was found to be sensitive, rapid and easy to handle without pretreatment of the sample. The logarithm of the frequency shift of the PQC shows a linear relationship to the logarithm of the concentration of phenytoin over the range 6.7 x 10(-8)-8.0 x 10(-4) M with a detection limit of 1.0 x 10(-8) M at pH 10.0. Recoveries were in the range 98.5-102.0%. Influencing factors were examined and optimized. Also discussed is the preliminary application of the phenytoin BAW sensor in serum and injection. The results for real samples obtained by the proposed method agreed with those obtained by conventional methods.     

A piezoelectric biomimetic sensor for aminopyrine with a molecularly imprinted polymer coating

A molecularly imprinted polymer for aminopyrine was synthesized using methacrylic acid as functional monomer. The polymer was employed as the recognition element of a piezoelectric bulk acoustic wave biomimetic sensor for aminopyrine. Influencing factors were investigated in detail and optimized. This sensor exhibited high selectivity and sensitivity to aminopyrine. The response range of the sensor was between 5.0 x 10(-8) and 1.0 x 10(-4) M with a detection limit of 2.5 x 10(-8) M in the aqueous system. Scatchard analysis with UV spectrophotometry showed that the same class of binding sites was formed in the molecularly imprinted polymer in the studied concentration range, and the dissociation constant and the apparent maximum number of these binding sites were estimated to be 2.29 mM and 165.0 mumol g-1 dry polymer, respectively. Impedance analysis was employed to verify the imprinting effect and lack of variation in the viscoelasticity of the polymer coating during detection.     

Real-time monitoring of formaldehyde-induced DNA-lysozyme cross-linking with piezoelectric quartz crystal impedance analysis

A novel method for monitoring, in real time, the formaldehyde (FA)-induced DNA-protein cross-linking process with the piezoelectric quartz crystal impedance (PQCI) technique is proposed. The method was used to monitor FA-induced DNA-lysozyme cross-link formation. Lysozyme was directly immobilized on the silver electrode surface of a piezoelectric quartz crystal by adsorption. The lysozyme-coated piezoelectric sensor was in contact with FA and DNA solutions. The time courses of the resonant frequency and equivalent circuit parameters of the sensor during the cross-linking were simultaneously obtained and are discussed in detail. On the basis of the feature of the multi-dimensional information provided by the PQCI technique, it was concluded that the observed frequency decrease could be mainly ascribed to the mass increase resulting from the cross-linking. According to the frequency decrease with time, the kinetics of the cross-linking process were quantitatively studied. A piezoelectric response model for the cross-linking was theoretically derived. Fitting the experimental data to the model, the kinetic parameters, such as the binding and dissociation rate constants (k(1) and k(-1)) and the cross-linking equilibrium constant (Ka), were determined. At 37 degrees C, the k(1), k(-1) and Ka values obtained were 7.0 (+/-0.1) x 10(-5) (microg ml(-1))(-1) s(-1), 6.6 (+/-0.1) x 10(-3) s(-1) and 1.06 (+/-0.02) x 10(-2) (microg ml(-1))(-1), respectively.     

Monitoring,and estimation of kinetic data,by piezoelectric impedance analysis,of the binding of the anticancer drug mitoxantrone to surface-immobilized DNA

A new method of monitoring drug binding to DNA, in real-time, by means of the piezoelectric quartz-crystal-impedance (PQCI) technique, is proposed. The method was used to monitor the binding of an anticancer drug, mitoxantrone (MX), to double-stranded calf-thymus DNA covalently immobilized on the thioglycollic acid-modified gold electrode surface of a quartz crystal. Optimum experimental conditions for the immobilization were established. The DNA-anchored piezoelectric sensor was in contact with MX solution. The time courses of the resonant frequency and the equivalent circuit characteristics of the sensor were also obtained during the study of DNA-drug binding. On the basis of the analysis of the multidimensional information provided by the PQCI technique the observed frequency decrease was mainly ascribed to the increase in the mass of the sensor surface resulting from the binding. The kinetics of the binding process were studied quantitatively by monitoring the frequency change with time and a piezoelectric response model for the binding was derived theoretically. The experimental data were fitted to the model and the binding and dissociation rate constants and the binding equilibrium constant were estimated to be 66.0+/-0.1 mol(-1) L s(-1), 1.4+/-0.1x10(-4) s(-1), and 4.71+/-0.07x10(5) mol(-1) L, respectively, at 37 degrees C.     

Study of the immobilization of alcohol dehydrogenase on Au-colloid modified gold electrode by piezoelectric quartz crystal sensor,cyclic voltammetry,and electrochemical impedance techniques

The immobilization of alcohol dehydrogenase (ADH) on Au-colloid modified gold electrodes has been investigated. Colloidal Au was first self-assembled onto gold electrodes through the thiol groups of an 1,6-hexanedithiol monolayer. Piezoelectric quartz crystal sensor, cyclic voltammetry, and electrochemical impedance techniques were used to investigate the immobilization of ADH on Au colloids. The cyclic voltammogram tends to be more irreversible with increased ADH concentration. In the impedance spectroscopic study, an obvious difference of the electron transfer resistance between the Au-colloid modified electrode and the bare gold electrode was observed. Using the piezoelectric quartz crystal sensor, the Michaelis constant, K(m), and the maximum initial rate, V(max), of the immobilized ADH were estimated as 6.03 x 10(-4) M and 0.63 Hzs (-1), respectively. The binding constant of ADH with nicotinamide adenine dinucleotide (NAD) was also determined as 1.87 x 10(4) M(-1). Experimental results showed that colloidal Au can be used as a biocompatible matrix for enzyme immobilization.     

Construction and analytical application of ion-selective piezoelectric sensor for atropine sulfate

The method describes the use of a piezoelectric quartz crystal (PQC) as a substitute for ion-selective electrodes. The approach is feasible when the membrane materials are electrically non-conductive and membrane potential measurements are consequently not possible. An ion-selective piezoelectric sensor sensitive to atropine sulfate was constructed by coating a PVC membrane containing activant on one the side of a PQC. On the basis of selective adsorption of atropine ions across the modified film and the sensitive mass response of PQC, the method exhibits a sensitive, rapid response and is easy to operate without pretreatment of the sample. The logarithm of the frequency shift gave a linear relationship with the logarithm of atropine sulfate concentration in the 1.0 x 10(-8)-1.0 x 10(-3) M range with a detection limit of 5.0 x 10(-9) M at pH 7.0. Recoveries were from 98.7-102.2%. Two activants, atropine tetraphenylborate and atropine dipicrylaminate, were synthesized and investigated. Influencing factors were also examined and optimized. The results for real samples obtained by the proposed method agreed with those obtained by conventional methods.     

Detection of complement C1-inhibitor with a piezoelectric immunosensor

A novel piezoelectric immunosensor has been developed for the detection of human complement C1-inhibitor. Anti-C1-inhibitor antibody was immobilized onto the gold electrodes of a 9 MHz AT-cut piezoelectric crystal. Coating the crystal with polyethyleneimine adhesion, followed by a glutaraldehyde cross-linking method to immobilize antibody showed better results than the physical adsorption method with respect to sensitivity and reproducibility. Under the optimized experimental conditions, the sensor showed good response to the C1-inhibitor in the range from 2.0 x 10(-8) to 1.2 x 10(-6) g. Other proteins in human serum did not remarkably interfere with the detection. The crystals could be regenerated 5 times, when bound materials on the crystal surface were eluted by strong acid and strong alkali solution and subsequently cleaned in an ultrasonic cleaner.     

A non-potentiometric sensing method for the determination of pentoxyverine with PQC sensors based on ion-pair complexes.

The construction and general performance characteristics of three piezoelectric quartz crystal sensors responsive to the pentoxyverine are described here. This kind of non-potentiometric sensing method is based on use of ion-pair complexes of the pentoxyverine cation with three counter anions, namely, tungstophosphate, tetraphenylborate and picrolonate. The complexes were embedded in a PVC matrix. Adsorption of the pentoxyverine ion on the complex caused a frequency decrease of the crystal. The frequency decrease was proportional to the amount of adsorbed analyte. The influencing factors were investigated in detail, and then optimized. The proposed sensors exhibit reasonable selectivity and a higher sensitivity than the potentiometric sensors. For a sensor modified with pentoxyverine-phosphotungstate, the calibration graph was linear over concentration of 1.0 x 10(-7) - 5.0 x 10(-5) M with a detection limit of 6 x 10(-8) M at pH 5.4.     

Covalently immobilized aminonaphthalimide as fluorescent carrier for the preparation of optical sensors

By replacing the hydrogen of the 4-amino group of a 4-amino-1,8-naphthalimide derivative with an N-acryloxyethyl group, the fluorophore has been covalently immobilized on an optical sensor surface by UV photopolymerization. The optical sensor obtained can be used for the determination of picric acid. The linear range and detection limit of the sensor are 9.80x10(-7)-1.96x10(-4) mol L(-1) and 7.1x10(-7) mol L(-1), respectively. Leaching of the fluorophore from the membrane is effectively prevented by covalent immobilization, resulting in a sensor with a relatively long lifetime. The response time of the sensor is short, and the reproducibility and reversibility are good. The sensor has been used for the indirect determination of the chloroquine content of pharmaceutical tablets.     

Novel sulfate ion-selective polymeric membrane electrode based on a derivative of pyrilium perchlorate

A sulfate ion-selective PVC membrane sensor based on 4-(4-bromophenyl)-2,6-diphenylpyrilium perchlorate (BDPP) as a novel sensing material is successfully developed. The electrode shows a good selectivity for sulfate ion with respect to common organic and inorganic anions. The sensor exhibits a good linear response with slope of -28.9+/-0.5 mV per decade over the concentration range of 1.0x10(-6)-1.0x10(-2) M, and a detection limit of 8.0x10(-7) M of SO(4)(2-) ions. The electrode response is independent of pH in the range of 4.0-9.0. The proposed sensor was applied as an indicator electrode in potentiometric titration of sulfate and barium ions, and to the determination of zinc in zinc sulfate tablets.     

Mebendazole selective membrane sensor and its application to pharmaceutical analysis.

A PVC membrane sensor for the selective determination of mebendazole (MBZ) was fabricated. The sensor is based on an ion association of MBZ with silicotungstic acid (STA) as ion pair and bis(2-ethylhexyl)phthalate (BEP) as the plasticizing agent in a PVC matrix. The sensor showed a linear response for MBZ for a concentration range 1.0x10(-6)-5.0x10(-2) M with a Nernstian slope of 55.8 mV/decade (limit of detection 6.3x10(-7) M) in the pH range 4-7. It has a fast response time of <30 s. The sensor showed a very good selectivity for MBZ with respect to a large number of ions. The direct determination of MBZ in pharmaceutical formulations gave results that compare well with the data obtained from the standard method.     

Study of a molecular imprinting polymer coated BAW bio-mimic sensor and its application to the determination of caffeine in human serum and urine

A bio-mimic bulk acoustic wave (BAW) sensor was fabricated by coating the caffeine (CAF) template molecular imprinting polymer (MIP). This sensor exhibited high selectivity and a sensitive mass response to CAF. The response range of the sensor was between 5.0 x 10(-9) and 1.0 x 10(-4) M with a detection limit of 5.0 x 10(-9) M at pH 8.0. Recoveries were 96.1-105.6%. Influencing factors were investigated in detail and optimized. When employed to detect real samples, the proposed method proved to be a convenient method with the advantages of high sensitivity, good selectivity and ease of handling.     

A flow-cell optosensor for lead based on immobilized dithizone

Dithizone immobilized on XAD-4 resin has been studied as a sensor element of an optical sensor for lead using a flow-cell. Using this arrangement, lead in solution has been determined in the concentration range 1 x 10(-5)-3 x 10(-7)M with a detection limit of 1 x 10(-8)M(i.e., 2 mug/l.). The standard deviation of the method for the measurement of lead at a concentration of 1 x 10(-6)M was found to be 7%. The response of the sensor was reproducible and can be regenerated using 0.01M hydrochloric acid followed by citrate-hydroxylamine solution.     

A coumarin derivative covalently immobilized on sensing membrane as a fluorescent carrier for nitrofurazone

A coumarin derivative 4-methyl-8-methylacrylamide-2H, 5H-pyrano [3, 2-C] benzpyran 2, 5-dione (MMPBD) has been synthesized as a fluorescent carrier for preparing an optical chemical sensor. The carrier is immobilized on a quartz glass plate surface treated with a silanizing agent to prevent the leakage of the dye. This MMPBD sensor can be utilized for a nitrofurazone (NF) assay based on fluorescence quenching. The sensor shows good repeatability, a long lifetime and a fast response of less then 50 s. NF can be determined in the range between 1.0x10(-6)-1.0x10(-3 )mol L(-1) with a detection limit of 8.0x10(-7) mol L(-1 )at pH 7.0.     

Development of an optical fibre Al(III) sensor based on immobilised chrome azurol S

Chrome azurol S immobilised on XAD-2 has been used in this study as a reagent phase for the development of an optical fibre Al(III) sensor. Using a kinetic approach, this sensor was able to give a linear response in the Al(III) concentration range of 1.3 x 10(-5)-2.0 x 10(-4) M with a limit of detection of 1.0 x 10(-4) M. The optimum responses were obtained at pH 6.0 and when the solution was stirred. The sensor response was found to have a repeatability and reproducibility of 1.6% and 5.8%, respectively. The results obtained for Al(III) determination in aqueous sample were in good agreement with those obtained using graphite furnace-atomic absorption spectrometry.     

An Eu(III) sensor based on N,N-diethyl-N-(4-hydroxy-6-methylpyridin-2-yl)guanidine.

A highly selective poly(vinyl chloride)-based membrane sensor produced by using N,N-diethyl-N-(4-hydroxy-6-methylpyridin-2-yl)guanidine (GD) as active material is described. The electrode displays Nernstian behavior over the concentration range 7.0 x 10(-5) - 1.0 x 10(-1) M. The detection limit of the electrode is 5.0 x 10(-5) M. The best performance was obtained with the membrane containing 30% PVC, 55% benzyl acetate, 5% GD and 10% oleic acid. The response of the sensor is pH-independent in the range of 3.0 - 7.0. The sensor possesses satisfactory reproducibility, fast response time (< 20 s), and specially excellent discriminating ability for Eu(III) ion with respect to the alkali, alkaline earth, transition and heavy metal ions. The membrane sensor was used as an indicator electrode in potentiometric titration of Eu(III) ion with EDTA. It was also applied in determination of fluoride ions in mouth wash preparations.     

Bulk acoustic wave sensor using molecularly imprinted polymers as recognition elements for the determination of pyrimethamine

A new bulk acoustic wave (BAW) sensor modified with a molecularly imprinted polymer (MIP) was fabricated and applied for the determination of pyrimethamine. This sensor exhibited high selectivity and sensitive response to pyrimethamine. Factors such as pH and the amount of coating influencing sensor properties, were investigated in detail and optimized. The calibration curve was linear in the range 6.0x10(-7)-1.0x10(-4) M. The determination limit was 2.0x10(-7) M. In harsh chemical environments such as high temperature, organic solvents, bases, acids, etc., the sensor still exhibited long-term stability. The proposed method has been satisfactorily applied for the determination of pyrimethamine in serum and urine media.