硫化CoMo/Al2O3-TiO2催化剂上CO催化还原SO2的研究

报导了Al2O3、Al2O3-TiO2和TiO2担载的硫化CoMo催化剂上CO催化还原SO2的规律性,结果表明，反应物分别在350 ℃、350～400 ℃间和400 ℃完全转化为CO2和元素S.在含TiO2的催化剂上,CO-SO2反应可同时按COS中间物机理和Redox机理进行,从而使尾气中COS的含量大为降低,提高了生成元素S的选择性.对反应机理进行了讨论.     

多孔Pd/TiO2-Al2O3催化剂上乙醇完全氧化的研究

利用模板剂-浸渍法制备出了不同焙烧温度下的多孔复合材料TiO2-Al2O3 和Pd/Al2O3-TiO2 催化剂,催化剂用来催化氧化乙醇。样品经过XRD,FT-IR,孔结构分析、TEM、XPS进行表征分析。250℃焙烧的Pd/TiO2-Al2O3催化剂具有最高的乙醇转化率和CO2生成率。高比表面积、均匀分散的金属Pd颗粒和丰富的表面吸附氧是其具有高的催化活性的主要原因。     

CeO2改性Cu/Al2O3催化剂上甲醇水蒸气重整制氢

研究CeO2改性Cu/Al2O3催化剂上甲醇水蒸气重整制氢反应过程,得到低温活性、氢选择性和稳定性较好的催化剂.Cu/A12O3催化剂中添加CeO2提高了催化剂的活性和稳定性,当CeO2质量分数为20%时,催化剂活性表现最佳.在反应温度250℃,水醇摩尔比为1.0,液体空速为3.28 h-1条件下,甲醇转化率为95.5%,氢气选择性为100%.此外,CeO2通过促进水气转化反应降低了重整气中CO的含量.Cu/CeO2/Al2O3催化剂在200 h的寿命实验中,活性仍保持在90.0%以上,而Cu/Al2O3催化剂在100 h的寿命实验中,活性已很快下降.XRD和TPR分析及表面元素分布结果表明,铜和铈相互作用促进了铜在催化剂表面的高度分散,阻止了铜晶粒团聚、烧结,促使铜晶粒细小化,促进了铜的还原,改善了Cu/CeO2/Al2O3催化剂的性能.     

CeO2改性Cu/Al2O3催化剂上甲醇水蒸气重整制氢

研究CeO2改性Cu/Al2O3催化剂上甲醇水蒸气重整制氢反应过程,得到低温活性、氢选择性和稳定性较好的催化剂.Cu/Al2O3催化剂中添加CeO2提高了催化剂的活性和稳定性,当CeO2质量分数为20％时,催化剂活性表现最佳.在反应温度250 ℃,水醇摩尔比为1.0,液体空速为3.28 h －1条件下,甲醇转化率为95.5％,氢气选择性为100％.此外,CeO2通过促进水气转化反应降低了重整气中CO的含量.Cu/CeO2/Al2O3催化剂在200 h的寿命实验中,活性仍保持在90.0％以上,而Cu/Al2O3催化剂在100 h的寿命实验中,活性已很快下降.XRD和TPR分析及表面元素分布结果表明,铜和铈相互作用促进了铜在催化剂表面的高度分散,阻止了铜晶粒团聚、烧结,促使铜晶粒细小化,促进了铜的还原,改善了Cu/CeO2/Al2O3催化剂的性能.     

制备条件对MoS2/Al2O3耐硫甲烷化催化剂性能的影响

本文研究了前驱体MoO_3的负载量、浸渍温度和焙烧温度等制备条件对Mo S2/Al_2O_3耐硫甲烷化催化剂性能的影响,并通过XRD和H2-TPR表征了催化剂的物相和还原性能。结果表明,随着负载量增加,MoO_3与Al_2O_3间的相互作用增强,Al2(Mo O4)3相增多,导致催化剂更难被还原硫化,MoO_3还原温度升高。浸渍温度对CO转化率和CH4选择性有一定的影响,浸渍温度为70℃时,MoO_3的生成增多,且还原温度最低,CO转化率较高,而CH4选择性和CO_2选择性变化不大。随着焙烧温度升高,CO转化率先升高后降低,对CH4和CO_2选择性影响不大,其中以450℃焙烧的CO转化率最高,600℃焙烧的CO转化率最低。当焙烧温度在400~450℃时,Al2(Mo O4)3和Mo4O11的特征峰基本上消失,能够完全生成MoO_3,且结晶度较好。因此,合适的焙烧温度为400~450℃。     

硫化镍和磷化镍的HDS加氢活性和稳定性

采用共沉淀法制备了高分散80％Ni/Al2O3催化剂,经350℃焙烧,得高分散NiO/Al2O3(NiO粒径～3 nm),将其以CS2硫化(310 ℃,4 h)或PPh3磷化(320 ℃,36 h),分别获得了高分散的硫化镍(Ni3S2和Ni3S4,5.8 nm)和Ni2P(7.0 nm),在二苯并噻吩(DBT)的加氢...     

TiO2／Al2O3负载量对气相酯交换合成碳酸甲丙酯的影响

采用XRD、N2 physical adsorption、XPS、NH3-TPD和吡啶吸附IR等技术,对碳酸二甲酯和丙醇气固相合成碳酸甲丙酯的TiO2/Al2O3催化剂进行了表征.实验结果表明,TiO2/Al2O3表面的Lewis酸中心是反应的催化活性位,酸性主要来源于Al2O3,TiO2起修饰作用,有利于选择性生成碳酸甲丙酯.随着Ti负载量的增加,TiO2在Al2O3表面由高度分散状态向晶态转变,其比表面积逐渐降低,但是TiO2/Al2O3的表面酸性质没有受到显著影响,L酸量先是增加,而后略有下降.当Ti负载量为5%时,DMC的转化率及MPC的选择性分别达到54.3%和88.1%.     

具有良好热稳定性的Al2O3改性Fe2O3基金催化剂

通过共沉淀法和沉积-沉淀法制备出了具有良好热稳定性的Al2O3改性Fe2O3基金催化剂, 并通过透射电镜(TEM)、X射线衍射(XRD)、N2吸附-脱附及热重和差示扫描量热(TG-DSC)分析等表征手段对催化剂的结构与表面形貌进行了研究分析. TEM测试结果表明: 500 ℃焙烧后, 未掺杂Al2O3的催化剂中金颗粒粒径分布较宽, 平均粒径约为7.0 nm, 载体颗粒尺寸在50-100 nm范围内; 而掺杂Al2O3的催化剂中金颗粒粒径分布变窄, 平均粒径约为5.0 nm, 且载体颗粒大小也明显小于未掺杂Al2O3的催化剂, 保持在30-50 nm的范围内. N2吸附-脱附测试结果表明, Al2O3的掺杂有利于保持催化剂的介孔结构和比表面积, 从而提高了载体的热稳定性. XRD和TG-DSC测试结果表明, Al2O3的掺杂可以有效地抑制Fe2O3的结晶, 进而抑制了高温焙烧过程中金颗粒的长大. 选用CO低温氧化反应对催化剂的活性进行了评价, 即使在500 ℃高温下焙烧12 h, 掺杂了Al2O3的催化剂仍然可在26.7 ℃将CO完全转化, 而未掺杂Al2O3的催化剂CO最低完全转化温度(T100)高达61.6 ℃. Al2O3的掺杂显著提高了催化剂的热稳定性能.     

MO(M=Cu和Ni)/TiO2/-Al2O3催化剂在CO+O2反应中的活性

采用X射线衍射(XRD),程序升温还原(TPR)等表征手段考察了TiO2改性对CuO(或NiO)在γ-Al2O3表面上分散以及还原性能的影响,同时检测了这些改性的催化剂在CO+O2反应中的活性.结果表明:TiO2的改性使得CuO和NiO在γ-Al2O3载体上的分散复杂化,产生了多种状态的氧化铜(氧化镍)物种.当负载量低于其在γ-Al2O3上的分散容量(0.56 mmol Ti4+/100 m2γ-Al2O3)时,TiO2的加入主要是抑制了CuO和NiO在γ-Al2O3载体上的分散;而当负载量远大于其分散容量时,出现了CuO和NiO在晶相TiO2(锐钛矿)上的分散.无论其负载量如何,TiO2的加入促进了CuO的还原.因此,在250℃的CO+O2反应中,改性的催化剂中具有更多的活性位,因而显示出更高的活性;相反,TiO2的改性则抑制了NiO的还原.因此,在350℃的CO+O2反应中,可还原的氧化镍的量明显少于未经改性的催化剂,导致改性催化剂的活性降低.     

微波辐射对浆态床合成甲醇CuO/ZnO/Al2O3催化剂前驱体晶相转变的影响

在微波辐射条件下,对CuO/ZnO/Al2O3催化剂的沉淀母液进行老化,通过XRD、TG、H2-TPR,FTIR、HR-TEM和XPS对前驱体及催化剂微观结构的进行表征,探讨了CuO/ZnO/Al2O3催化剂前驱体晶相转变过程中微波辐射的作用。结果表明,微波辐射有利于Cu2+取代Zn5(CO3)2(OH)6中Zn2+的同晶取代反应。微波辐射的老化过程中,首先发生Cu2+取代Zn5(CO3)2(OH)6中Zn2+生成(Cu,Zn)5(CO3)2(OH)6的同晶取代反应,并于1.0 h内基本完成;随着老化时间继续延长,主要进行Zn2+取代Cu2(CO3)(OH)2中Cu2+生成(Cu,Zn)2(CO3)(OH)2的同晶取代反应,同时(Cu,Zn)5(CO3)2(OH)6进一步结晶。与常规老化1 h制备的前驱体相比,微波辐射老化1.0 h制备的前驱体含有较多的(Cu,Zn)5(CO3)2(OH)6物相,有助于增强焙烧后CuO/ZnO/Al2O3催化剂中CuO-ZnO协同作用,提高表面铜含量,进而提高CuO/ZnO/Al2O3催化剂在浆态床合成甲醇的催化活性和稳定性,在400 h浆态床合成甲醇评价期间,甲醇时空收率最大达318.9 g.kg-1.h-1,失活率仅为0.11%.d-1。     

Sc2MgGa2 and Y2MgGa2

Scandium magnesium gallide, Sc₂MgGa₂, and yttrium magnesium gallide, Y₂MgGa₂, were synthesized from the corresponding elements by heating under an argon atmosphere in an induction furnace. These intermetallic compounds crystallize in the tetragonal Mo₂FeB₂‐type structure. All three crystallographically unique atoms occupy special positions and the site symmetries of (Sc/Y, Ga) and Mg are m2m and 4/m, respectively. The coordinations around Sc/Y, Mg and Ga are pentagonal (Sc/Y), tetragonal (Mg) and triangular (Ga) prisms, with four (Mg) or three (Ga) additional capping atoms leading to the coordination numbers [10], [8+4] and [6+3], respectively. The crystal structure of Sc₂MgGa₂ was determined from single‐crystal diffraction intensities and the isostructural Y₂MgGa₂ was identified from powder diffraction data.     

Electrochemical study of (NEt4)2Cl2FeS2MoS2 and (NEt4)2Cl2FeS2MoS2FeCl2

Summary The ability of [MoS₄]^2–, anions to be used as ligands for transition metal ions has been widely demonstrated, especially with Fe²⁺. The present study has been restricted to linear complexes such as (NEt₄)₂ [Cl₂FeS₂MoS₂] and (NEt₄)₂[Cl₂FeS₂MoS₂FeCl₂]. Their electrochemical properties are described: upon electrochemical reduction, these compounds yield MoS₂, as a black precipitate, and an iron complex in solution, assumed to be [SFeCl₂]^2–. The electrochemical reduction goes through two electron transfers, coupled with the breakdown of the molecular skeleton: a DISPl and an ECE mechanism. Depending on the solvent, the following equilibrium may be observed: [Cl₄Fe₂MoS₄]^2–[Cl₂FeMoS₄]^2–+FeCl₂. The equilibrium constant, K_D, was evaluated by differential pulse polarography. K_D is tightly related to the donor number of the solvent.     

The alkali hypophosphites KH2PO2, RbH2PO2 and CsH2PO2

The structures of the hypophosphites KH₂PO₂ (potassium hypophosphite), RbH₂PO₂ (rubidium hypophosphite) and CsH₂PO₂ (caesium hypophosphite) have been determined by single‐crystal X‐ray diffraction. The structures consist of layers of alkali cations and hypophosphite anions, with the latter bridging four cations within the same layer. The Rb and Cs hypophosphites are isomorphous.     

Zur Kenntnis der Dialkalimetalldichalkogenide β-Na2S2, K2S2, α-Rb2S2, β-Rb2S2, K2Se2, Rb2Se2, α-K2Te2, β-K2Te2 und Rb2Te2

On Dialkali Metal Dichalcogenides β-Na₂S₂, K₂S₂, α-Rb₂S₂, β-Rb₂S₂, K₂Se₂, Rb₂Se₂, α-K₂Te₂, β-K₂Te₂ and Rb₂Te₂ The first presentation of pure samples of α- and β-Rb₂S₂, α- and β-K₂Te₂, and Rb₂Te₂ is described. Using single crystals of K₂S₂ and K₂Se₂, received by ammonothermal synthesis, the structure of the Na₂O₂ type and by using single crystals of β-Na₂S₂ and β-K₂Te₂ the Li₂O₂ type structure will be refined. By combined investigations with temperature-dependent Guinier-, neutron diffraction-, thermal analysis, and Raman-spectroscopy the nature of the monotropic phase transition from the Na₂O₂ type to the Li₂O₂ type will be explained by means of the examples α-/β-Na₂S₂ and α-/β-K₂Te₂. A further case of dimorphic condition as well as the monotropic phase transition of α- and β-Rb₂S₂ is presented. The existing areas of the structure fields of the dialkali metal dichalcogenides are limited by the model of the polar covalence.     

Formal [(2+2)+2] and [(2+2)+(2+2)] nonconjugated dienediyne cascade cycloadditions

[reaction: see text] Fluoranthene 2 and heptacycle 3 are easily accessible from the reaction of diyne 1 and norbornadiene (NBD) in the presence of the rhodium catalyst. The unusual [(2+2)+(2+2)] adduct 3 was confirmed by the X-ray crystal structure analysis.     

Crystal Structures of [Bu2Sn(O2PPh2)2], [Ph2Sn(O2PPh2)2], and [PhClSn(O2PPh2)OMe]2. Raman Spectra of [Ph2Sn(O2PPh2)2] and [PhClSn(O2PPh2)OMe]2

[(n‐Bu)₂Sn(O₂PPh₂)₂] ( 1 ), and [Ph₂Sn(O₂PPh₂)₂] ( 2 ) have been synthesized by the reactions of R₂SnCl₂ (R=n‐Bu, Ph) with HO₂PPh₂ in Methanol. From the reaction of Ph₂SnCl₂ with diphenylphosphinic acid a third product [PhClSn(O₂PPh₂)OMe]₂ ( 3 ) could be isolated. X‐ray diffraction studies show 1 to crystallize in the monoclinic space group P2₁/c with a = 1303.7(1) pm, b = 2286.9(2) pm, c = 1063.1(1) pm, β = 94.383(6)°, and Z = 4. 2 crystallizes triclinic in the space group , the cell parameters being a = 1293.2(2) pm, b = 1478.5(4) pm, c = 1507.2(3) pm, α = 98.86(3)°, β = 109.63(2)°, γ = 114.88(2)°, and Z = 2. Both compounds form arrays of eight‐membered rings (SnOPO)₂ linked at the tin atoms to form chains of infinite length. The dimer 3 consists of a like ring, in which the tin atoms are bridged by methoxo groups. It crystallizes triclinic in space group with a = 946.4(1) pm, b = 963.7(1) pm, c = 1174.2(1) pm, α = 82.495(6)°, β = 66.451(6)°, γ = 74.922(6)°, and Z = 1 for the dimer. The Raman spectra of 2 and 3 are given and discussed.     

Die Photoionenspektren von SCl2, S2Cl2 und S2Br2

Photoionization Mass Spectra of SCl₂, S₂Cl₂, and S₂Br₂ Photoionization mass spectra of SCl₂, S₂Cl₂, and S₂Br₂ have been measured. Heats of formation, bond energies, and ionization potentials of fragments have been calculated from appearance potentials.