Capillary zone electrophoretic determination of iodide in seawater using transient isotachophoresis with artificial seawater as the background electrolyte

We describe an application of capillary zone electrophoresis (CZE) with transient isotachophoresis (ITP) as the on-line concentration procedure for the determination of iodide in seawater. The effective mobility of iodide was decreased by the addition of 10 mM cetyltrimethylammonium chloride (CTAC) to an artificial seawater background electrolyte (BGE) so that transient ITP functioned and iodide was separated from other coexisting anions such as bromide, nitrite, and nitrate in seawater samples. After sample injection, 600 mM acetate was separately injected into the capillary as the terminating ion to generate transient ITP. The limit of detection (LOD) for iodide was 3.0 microg/L. The LOD was obtained at a signal-to-noise ratio (S/N) of 3. The values of the relative standard deviation (RSD) of peak area, peak height, and migration time for iodide were 2.9, 2.1, and 0.6%. The proposed method was applied to the determination of iodide in seawater collected around the Osaka Bay. The results obtained by use of the calibration graph were agreed with those obtained by the addition of the standard solutions for iodide.     

Importance of the counterion in optimization of a borate electrolyte system for analyses of anions in samples with complex matrices performed by capillary zone electrophoresis

Borate buffers are common background electrolytes for analyses of anions in capillary zone electrophoresis. Usually, sodium borate at a given pH is used and this specification seems to be sufficient for a successful analysis. In this paper, we show that free migration of OH(-) may deteriorate the analysis of a typical anionic analysis of clinical samples due to uncontrolled migration of OH(-) throughout the systems of analyzed zones and may damage the stacking of anionic analytes of interest. We have proven that the use of ammonium borate may remedy the situation where the presence of ammonium may selectively stop the free migration of OH(-) ions, slow down their effective mobility and bring their safe behavior resulting in reproducible stacking of clinically important anions. Results of real analyses of human serum samples confirmed the proposed method and proved that substitution of sodium for ammonium in borate buffers offers reliable analyses of clinical samples having chloride as the bulk component. The experimental results given in this paper are supported also by computer simulation, which can not only support the positive results but also show the dynamics of the separation that is otherwise hidden to any detection possibilities.     

Simultaneous determination of ofloxacin and ornidazole in pharmaceutical preparations by capillary zone electrophoresis

A simple, rapid and validated capillary electrophoretic method has been developed for the separation and determination of ofloxacin and ornidazole in pharmaceutical formulations with detection at 230 nm. Optimal conditions for the quantitative separations were investigated. Analysis times shorter than 4 min were obtained using a background electrolyte solution consisting of 25 mmol/L phosphoric acid adjusted with 1 m Tris buffer to pH 8.5, with hydrodynamic injection of 5 s and 20 kV separation voltage. The validation criteria for accuracy, precision, linearity and limits of detection and quantitation were examined and discussed. An excellent linearity was obtained in concentration range 25–250 µg/mL. The detection limits for ofloxacin and ornidazole were 1.03 ± 0.11 and 1.80 ± 0.06 µg/mL, respectively. The proposed method has been applied for the analysis of ofloxacin and ornidazole both individually and in a combined dosage tablet formulation. The proposed validated method showed recoveries between 96.16 and 105.23% of the nominal contents. Copyright © 2009 John Wiley & Sons, Ltd.     

Reverse flow injection spectrophotometric determination of iodate and iodide in table salt

A very simple and sensitive reverse flow injection method is described for the determination of iodate and iodide. The iodate reacts with excess iodide in acidic medium to form tri-iodide, which can be spectrophotometrically monitored at 351 nm, and the absorbance is directly related to the concentration of iodate in the sample. The determination of iodide is based on oxidizing iodide to iodate. The calibration curve is linear in the range of 0.02-3.0 μg ml⁻¹ I with r²=0.9998, and the limit of detection is 0.008 μg ml⁻¹ I. The chemical and flow injection variables were studied and optimized to make the procedure suitable for quantitating iodate and iodide in table salts. It is shown that the reverse flow injection analysis could greatly improve the sensitivity and precision for determination of iodate with a relative standard deviation of 0.9%. A complete analysis, including sampling and washing, could be performed in 35 s. The procedure was applied successfully to the determination of iodate and iodide in table salts, and the results were statistically compared with results determined by standard iodometry method.     

Determination of anions in rainwater by capillary electrophoresis with conductivity detection

A routine method for the determination of chloride, nitrate and sulfate anions in rainwater by capillary electrophoresis was developed. The system uses an end-column non-suppressed conductivity detector. Linear calibration plots were generated from 0.050 to 20 mg/l, which is the range generally found in wet depositions. Accuracy and precision were evaluated by analyzing certified standards of simulated rainwater and environmental samples, or by comparing CE results with those obtained by IC, the reference technique for anion analysis in wet deposition. The reproducibility of the method was satisfactory except at the lower and upper limits of the analytical range. Sensitivity lay in the range of few μg/l.     

Simultaneous determination of bromide and iodide ions by capillary isotachophoresis using quaternary ammonium salts

Bromide and iodide ions were determined simultaneously by capillary isotachophoresis using an aqueous electrolyte system; the separation principle was based on the ion-pairing equilibria between tetradecyldimethylbenzylammonium ion and these anions in the leading electrolyte. The interaction between iodide ion and tetradecyldimethylbenzylammonium ion was stronger than that for bromide ion. Thus complete separation of bromide and iodide ions could be obtained by using a leading electrolyte containing 1.5 mM tetradecyldimethylbenzylammonium ion. The pH of the leading electrolyte was adjusted to 5.0. The relative standard deviations of the zone length for bromide and iodide ions were 1.1 and 1.2%, respectively, when mixture of 3.0 mM of these ions was analysed. A 150-μl volume could be injected for the simultaneous determination of low concentrations of bromide and iodide ions.     

邻苯二甲酸为背景吸收电解质的毛细管电泳法测定低分子量肝素中的阴离子

在生产和贮存低分子量肝素的过程中,糖链上的硫酸酯基团会被水解而损失活性,因此肝素样品中常可以检测到游离的硫酸根离子,此外在生产过程中还会引入其他阴离子。为了检测低分子量肝素的质量稳定性,常用离子色谱检测低分子量肝素中游离的阴离子。但是相对分子质量较大的低分子量肝素会污染离子色谱柱和抑制器。为此发展了一种灵敏的毛细管电泳方法用于测定低分子量肝素中游离的SO~(2-)_4、Cl~-、F~-、PO~(3-)_4和OAc~-。不同于常用的背景吸收离子铬酸根,采用邻苯二甲酸根作为背景吸收电解质。与铬酸根相比,邻苯二甲酸根与所有待测阴离子电泳淌度匹配得更好,因此可以获得较窄的峰形。而且邻苯二甲酸根在230 nm检测波长下的摩尔吸光系数(4 754 L/(mol·cm))比铬酸根(254 nm,2 400 L/(mol·cm))高。因此,可以将毛细管电泳检测阴离子的灵敏度提高到与离子色谱法相当的水平。通过验证,该方法在0.002~1 mmol/L的浓度范围内具有较好的线性关系,日内(n=6)和日间(n=3)迁移时间和峰面积的相对标准偏差均小于3%。所测阴离子的检出限(S/N=3)和定量限(S/N=10)分别为0.4~0.8μmol/L和2~4μmol/L。该方法可用于监测低分子量肝素的稳定性。     

毛细管区带电泳法同时分离测定香兰素和邻位香兰素异构体

建立了同时测定香兰素和其异构体邻位香兰素的毛细管区带电泳法(CZE)。考察了缓冲溶液的种类、浓度和pH以及分离电压等因素对分离结果的影响。在缓冲溶液为50 mmol/L硼砂-150 mmol/L磷酸氢二钠(pH 7.5)、分离电压15 kV的优化条件下,6 min内即可实现分离。香兰素和邻位香兰素在10～240 mg/L范围内线性关系良好,相关系数分别为0.9999和0.9997;方法的检出限均为1.0 mg/L (信噪比为3);样品的加标回收率为99.4%～101.2%,相对标准偏差为0.19%～0.73%。该方法操作简单、快速,已应用于实际样品的分析,并获得了令人满意的结果。     

Simultaneous determination of atenolol,chlorthalidone and amiloride in pharmaceutical preparations by capillary zone electrophoresis with ultraviolet detection

Capillary zone electrophoresis methods for the simultaneous determination of the β‐blocker drugs, atenolol, chlorthalidone and amiloride, in pharmaceutical formulations have been developed. The influences of several factors (buffer pH, concentration, applied voltage, capillary temperature and injection time) were studied. Using phenobarbital as internal standard, the analytes were all separated in less than 4 min. The separation was carried out in normal polarity mode at 25°C, 25 kV and using hydrodynamic injection (10 s). The separation was effected in an uncoated fused‐silica capillary (75 μm i.d. × 52 cm) and a background electrolyte of 25 mm H₃PO₄ adjusted with 1 m NaOH solution (pH 9.0) and detection at 198 nm. The method was validated with respect to linearity, limit of detection and quantification, accuracy, precision and selectivity. Calibration curves were linear over the range 1–250 μg/mL for atenolol and chlorthalidone and from 2.5–250 μg/mL for amiloride. The relative standard deviations of intra‐ and inter‐day migration times and corrected peak areas were less than 6.0%. The method showed good precision and accuracy and was successfully applied to the simultaneous determination of atenolol, chlorthalidone and amiloride in various pharmaceutical tablets formulations. Copyright © 2010 John Wiley & Sons, Ltd.     

Simultaneous determination of sulfamethoxazole and trimethoprim in human plasma by capillary zone electrophoresis

A capillary electrophoretic method for the simultaneous determination of sulfamethoxazole and trimethoprim in plasma was developed. Sulfamethoxazole and trimethoprim extracted from human plasma with ethyl acetate were analyzed at 20 kV and 25 degrees C using 15 mm phosphate buffer (pH 6.2) as the electrolyte. The detection was by UV at 220 nm. The run time was 8.0 min and the limit of quantification was 10.00 microg/mL for sulfamethoxazole and 2.00 microg/mL for trimethoprim. The recovery was >99% for both compounds. This method enabled the detection of sulfamethoxazole and trimethoprim in plasma of patients after oral ingestion of their combined formulation. The present simple and rapid method is applicable to drug monitoring in immunocompromised patients who are taking the combined formulation of these compounds for the treatment or prophylaxis of Pneumocystis carinii pneumonia.     

离子液体为背景电解质的毛细管电泳-间接紫外检测法同时测定葡萄酒中无机阴离子和阳离子

以离子液体1-乙基-3-甲基咪唑对甲苯磺酸盐([EMIm]TS)为背景电解质,采用双端进样方式,实现了毛细管电泳-间接紫外检测法同时分析测定葡萄酒中无机阳离子(K⁺、Ca²⁺、Na⁺、Mg²⁺和Li⁺)和阴离子(Cl^-、SO■和ClO^-₃)。[EMIm]TS作为电泳缓冲溶液的同时,其阳离子和阴离子分别作为样品中阳离子和阴离子组分的间接紫外检测的背景电解质。在最佳分析条件下,可在6.5 min内完成8种无机离子的同时分离检测,其线性范围为0.005～0.7 g/L,相关系数为0.963～0.995,检出限(S/N=3)为1.2～12.5 mg/L。该方法成功测定了3种不同品牌的市售葡萄酒中8种无机离子。在3个加标水平下,8种无机离子的回收率为90.1%～110.5%,相对标准偏差(RSD)≤4.8%。结果表明,该方法可应用于葡萄酒中无机阴、阳离子的同时分离检测,且方法简单、快速且结果可靠。     

Sensitive determination of anions in saliva using capillary electrophoresis after transient isotachophoretic preconcentration

A transient isotachophoresis-capillary electrophoresis (tITP-CE) system for the determination of minor inorganic anions in saliva is described. The complete separation and quantification of bromide, iodide, nitrate, nitrite, and thiocyanate has been achieved with only centrifugation and dilution of the saliva sample. In-line tITP preconcentration conditions, created by introduction of the plugs of 5 mM dithionic acid (leading electrolyte) and 10 mM formic acid (terminating electrolyte) before and after the sample zone, respectively, allowed the limits of direct UV absorption detection (at 200 nm) to be up to 50-fold improved as compared with CE without tITP. As a result, nitrate and thiocyanate were still detectable at 4.6 and 3.8 μg l⁻¹, respectively, in 1000 times diluted saliva. The daily variations of anionic concentrations in saliva samples taken from a smoking health volunteer were discussed based on the results of tITP-CE analysis. It was confirmed that the thiocyanate concentration in saliva noticeably increased after smoking. This is apparently the first report on simultaneous quantification of more than four anionic salivary constituents using CE.     

Determination of phosphate in natural waters by capillary electrophoresis Influence of solution composition on migration time and response

This paper deals with the determination of the more complex phosphate anion by capillary electrophoresis using indirect UV detection. First, the pH of the running electrolyte influences both the migration time and the response of the phosphate anion. Both effects could be explained well by taking into account phosphorus speciation in solution. In addition, the experimental method has been applied to three different sets of natural water systems; (i) groundwater, (ii) surface water and (iii) stemflow samples. The migration time behaviour of phosphate was different for the three sample sets and, hence, difficulties arise with respect to a clear and unique identification of the compound. Deviations herein could be minimized by applying a correction method for migration time drift. Concentrations of phosphate could be quantified in most samples and were confirmed by a calorimetric method. Average recoveries of additions of phosphate to groundwater, surface water and stemflow samples were 105, 83 and 103%, respectively. For one stemflow sample, quantitative recovery of phosphate was possible only by changing the pH of the running electrolyte solution. The latter observation might be very useful in setting up speciation-related measurement methods.     

Improvement of capillary zone electrophoresis sensitivity with artificial seawater as the background electrolyte utilizing transient isotachophoresis for the determination of nitrate and nitrate ions in seawater

We describe capillary zone electrophoresis (CZE) with transient isotachophoresis (ITP) for the determination of low concentrations of nitrite and nitrate ions in seawater. Bromide-free artificial seawater was adopted as background electrolyte (BGE) to eliminate the interference of high concentrations of salts in seawater. To reverse the electroosmotic flow (EOF), 3 mM cetyltrimethylammonium chloride (CTAC) was added to the BGE. High concentrations of chlorate were added to sample solutions as the terminating ion to generate the ITP process before the CZE separation. In general, the stacking effect increased with increasing amounts of chlorate injected into the capillary. The limits of detection (LODs) for nitrite and nitrate were 0.063 and 0.033 mg/L when the chlorate concentration was 600 and 200 mM, respectively; these were half of those obtained by CZE without the transient ITP. The LODs were obtained at a signal to noise ratio (S/N) of 3. The relative standard deviations (RSD, n = 10) of the peak areas for these ions were 3.2 and 2.9%. The RSDs of peak heights for these ions were 1.6 and 2.1%. The RSDs of migration times for these ions were 0.67 and 0.46%.     

Trace ion analysis of seawater by capillary electrophoresis: determination of iodide using transient isotachophoretic preconcentration

An improved transient isotachophoresis (tITP) procedure for the preconcentration of iodide from highly saline matrices was developed with the objective to quantify iodide in seawater by capillary electrophoresis (CE). The procedure takes advantage of introducing cetyltrimethylammonium chloride into the high-sodium chloride background electrolyte, which due to a specific interaction with iodide amended placement of the analyte at a large distance from the matrix chloride (the latter performed the role of a leading anion). Computer simulation showed that 2-(N-morpholino)ethanesulfonate could be adopted as a suitable terminating ion to enable isotachophoretic focusing at the beginning of the CE run. Under optimized tITP conditions, the sensitivity response of iodide was improved by a factor of 140 over normal CE mode. This allowed for direct UV detection of as low as 0.6 microg/L iodide and made feasible CE analysis of undiluted surface seawater samples where iodide was found at a 30 microg/L level. The applicability of the proposed tITP-CE method could apparently be extended to the determination of other trace seawater anions (e.g., iodate).     

Rapid optimized separation of bromide in serum samples with capillary zone electrophoresis by using glycerol as additive to the background electrolyte

After decades of neglect, bromide has recently been re-introduced in therapy as an effective anti-epileptic drug. The present paper describes the methodological optimization and validation of a method based on capillary zone electrophoresis for the rapid determination of bromide in serum using a high-viscosity buffer and a short capillary (10 cm). The optimized running buffer was composed of 90 mM sodium tetraborate, 10 mM sodium chloride, pH 9.24 and 25% glycerol. The separation was carried out at 25 kV at a temperature of 20 °C. Detection was by direct UV absorption at 200 nm wavelength. The limit of detection (signal-to-noise ratio = 5) in serum was 0.017 mM. The precision of the method was verified in blank serum samples spiked with bromide, obtaining intra-day and day-to-day tests, relative standard deviation values ≤0.2% in terms of migration times and values <2% in terms of peaks areas, respectively.     

Determination of chlorite in drinking water by on-line coupling of capillary isotachophoresis and capillary zone electrophoresis

An isotachophoresis (ITP)–capillary zone electrophoresis (CZE) combination was used for the determination of chlorite in drinking waters. No sample preparation is needed and no interfering by other anions in tap water was observed. The reached limits of detection with conductivity detector were 0.012–0.017 mg l⁻¹. By four-fold sample loading with a 30 μl valve, 0.005 mg l⁻¹ of chlorite was determined with R.S.D.=3.3%. The concentrations of 0.05 and 0.20 mg l⁻¹ were measured with R.S.D. of 2.2 and 2.7%, respectively. The recoveries of chlorite from drinking water were 96–106% in the range of 0.02–0.20 mg l⁻¹. The R.S.D. values of migration times (inter-day) were up to 1.3%. The time for analysis is about 15 min.     

Routine determination of major anions in atmospheric aerosols by capillary electrophoresis

Capillary electrophoresis (CE) with indirect UV detection utilizing a pyromellitate-based electrolyte was used for the routine analysis of major anions in atmospheric aerosols collected on filters with high-volume (Hi-Vol) samplers. The long-term reliability of the CE system was checked over an 8-month period during which over 2900 samples were analyzed. In addition, approximately 1100 samples were analyzed in parallel by ion chromatography (IC). It has been shown that acceptable analytical performance can be routinely obtained. The agreement between the CE and IC results is good, generally better than 20% at concentrations larger than 1 mg l⁻¹.     

Simultaneous determination of atenolol and amiloride in pharmaceutical preparations by capillary zone electrophoresis with capacitively coupled contactless conductivity detection

Capillary zone electrophoresis coupled with a capacitively coupled contactless conductivity detector (CE‐C⁴D) has been employed for the determination of atenolol and amiloride in pharmaceutical formulations. Acetic acid (150 mm ) was used as background electrolyte. The influence of several factors (detector excitation voltage and frequency, buffer concentration, applied voltage, capillary temperature and injection time) was studied. Non‐UV‐absorbing L‐valine was used as internal standard; the analytes were all separated in less than 7 min. The separation was carried out in normal polarity mode at 28°C, 25 kV and using hydrodynamic injection (25 s). The separation was effected in an uncoated fused‐silica capillary (75 μm, i.d. × 52 cm). The CE‐C⁴D method was validated with respect to linearity, limit of detection and quantification, accuracy, precision and selectivity. Calibration curves were linear over the range 5–250 μg/mL for the studied analytes. The relative standard deviations of intra‐ and inter‐day migration times and corrected peak areas were less than 6.0%. The method showed good precision and accuracy and was successfully applied to the simultaneous determination of atenolol and amiloride in different pharmaceutical tablet formulations. Copyright © 2010 John Wiley & Sons, Ltd.     

Simultaneous determination of inorganic anions, calcium and magnesium by suppressed ion chromatography

Suppressed conductimetric detection ion chromatography (IC) was investigated for the separation and detection of common inorganic anions, calcium and magnesium by anion-exchange chromatography using a sodium carbonate-EDTA mobile phase. The formation of anionic Ca2+ -EDTA and Mg2+ -EDTA complexes allowed its separation from other inorganic anions opening the way for their simultaneous determination in a single chromatographic run. The effect of the pH, carbonate and EDTA concentrations in the eluent and the previous addition of EDTA to the samples has been studied. The optimised experimental conditions were applied to the determination of Ca2+ and Mg2+ in mineral waters with results in agreement with alternative ICP-MS methodologies.