一种探针-样品距离的切变力控制新方法

报道了近场扫描光学显微镜(Near-filed Scanning Optics Microscope-NSOM)中一种基于切变力的探针-样品间距控制新方法.条形压电蜂鸣器片的上表面电极被沿着中心线分成两半,一半用于驱动,其上施加振荡源谐振频率进行激励,另一半上粘附光纤探针,并利用压电效应作为光纤探针的振幅传感器.当受振动激励的光纤探针由远处逐渐接近样品表面时,由于样品与探针之间的切变力阻尼作用使得探针的振幅减小,通过检测探针振幅的变化可以控制探针与样品的间距.我们建立了一套探针-样品间距探测控制系统并利用该系统获得了CD盘片表面8μm×8μm范围内的切变力形貌图.     

一种探针-样品距离的切变力控制新方法

报道了近场扫描光学显微镜(Near-filed Scanning Optics Microscope NSOM)中一种基于切变力的探针 样品间距控制新方法.条形压电蜂鸣器片的上表面电极被沿着中心线分成两半,一半用于驱动,其上施加振荡源谐振频率进行激励,另一半上粘附光纤探针,并利用压电效应作为光纤探针的振幅传感器.当受振动激励的光纤探针由远处逐渐接近样品表面时,由于样品与探针之间的切变力阻尼作用使得探针的振幅减小,通过检测探针振幅的变化可以控制探针与样品的间距.我们建立了一套探针 样品间距探测控制系统并利用该系统获得了CD盘片表面8μm×8μm范围内的切变力形貌图.     

一种基于大角度倾斜光纤光栅包层模的低频声传感方案

利用倾斜光纤光栅在发生弯曲时其存在的多种纤芯-包层模式耦合方式容易发生改变,进而使其光谱特征发生明显变化的特点,提出并验证了一种基于大角度倾斜光纤光栅包层模的低频声传感方案.将倾斜光纤光栅与设计的聚对苯二甲酸乙二酯(PET)换能膜片及腔体结构相结合,得到了一种有效的低频声传感系统.该换能膜片在被测声波信号作用下产生振动,使固定在膜片表面的倾斜光纤光栅发生周期性动态弯曲,引起倾斜光纤光栅的包层模式光谱发生周期性漂移,最后采用边缘滤波法进行解调,实现低频被测声波的有效探测.实验结果显示,该传感方案可以在45—220 Hz范围内实现高灵敏度声波探测,在传感系统固有频率附近54 Hz处获得最大声灵敏度115.88 m V/Pa,且最小探测声压为539.2μPa/Hz^1/2.该传感方案具有灵敏度高、重复性好、结构简单、容易加工等优势,在低频声探测等相关应用领域具有较大的发展前景.     

双层孔大模场微结构光纤的模式特性分析

本文分析一种由两层低折射率孔组成的大模场光纤的模式特性,采用多极法和有限元方法数值计算并分析了内层孔与外层孔尺寸变化对光纤基模与高阶模的束缚损耗与弯曲损耗的影响,设计获得了一种具有较高的高阶模和基模损耗比同时允许一定程度弯曲的大模场光纤,结果表明:当内层孔直径为34μm,外层孔直径为24 μm时,其基模束缚损耗为0.00017 dB m,而高阶模束缚损耗为1.39 dB/m;光纤的基模模场面积为2450.9μm2,当弯曲半径为1.2m 时,弯曲损耗为0.106 dB/m.     

一种小尺寸抗弯曲光纤的制备与性能研究

制备了一种外径远小于常规G.652光纤的大模场抗弯曲单模光纤.通过设计凹陷包层的预制棒结构,提高光缆光纤的抗弯曲性能,同时保持与G.652光纤相似的模场直径.测试结果显示光纤涂层外径为180μm、模场直径为9.1μm,且在7.5 mm半径单圈弯曲下,其宏弯损耗低于0.4 dB@1550 nm,长期环境性能附加衰减不大于...     

内窥式二维光纤扫描探头及其驱动方法

基于压电换能器技术设计了一种应用于光学相干层析成像的新型内窥式二维光纤扫描探头,即利用两片压电陶瓷片和一片薄导电基片驱动光纤探头.该探头利用光纤悬臂的共振特性,通过对压电陶瓷施加等于光纤共振频率的混频信号,能同时激发光纤悬臂两正交方向上的振动,可以实现光纤悬臂的二维扫描.建立了理论模型并进行了有限元仿真分析,最后搭建了实验系统,验证并获得了扫描图样.实验结果实现了光纤悬臂的二维扫描,扫描范围达到(500×500)μm,调节驱动信号振幅幅值可以调节扫描范围.实验结果与理论分析和仿真相吻合,验证了方案的可行性.     

多芯光纤及其在弯曲传感中的应用（英文）

采用纤芯间距为38.78μm的国产多芯光纤设计了一种光纤弯曲传感器.该多芯光纤弯曲传感器由长度为1m的七芯光纤与单模光纤拼接制成,多芯光纤弯曲时,相邻的纤芯发生模式耦合.在传感器一侧,将宽带光注入到位于多芯光纤中心的纤芯,用光谱分析仪测量带有曲率信息的频谱,获得弯曲传感器的透射谱波长偏移与弯曲曲率半径的关系.结果表明:多芯光纤弯曲半径越小,弯曲曲率越大,串扰越明显.     

内窥式二维光纤扫描探头及其驱动方法

基于压电换能器技术设计了一种应用于光学相干层析成像的新型内窥式二维光纤扫描探头,即利用两片压电陶瓷片和一片薄导电基片驱动光纤探头.该探头利用光纤悬臂的共振特性,通过对压电陶瓷施加等于光纤共振频率的混频信号,能同时激发光纤悬臂两正交方向上的振动,可以实现光纤悬臂的二维扫描.建立了理论模型并进行了有限元仿真分析,最后搭建了...     

全固态八边形大模场光子晶体光纤的设计

提出一种新型的全固态八边形大模场低损耗的掺镱石英光子晶体光纤,利用多极法对光纤的结构和特性进行了模拟.这种结构的光子晶体光纤空气孔由掺有少量氧化硼的石英棒代替,简化了制备过程,提高了光纤的热损伤阈值.在波长为1064 μm处,光纤的模场面积可达2000 μm²,还可实现单模传输,而且其弯曲损耗很小,当弯曲半径为5 cm时弯曲损耗小于05 dB/m.这种光纤对光纤激光器和光纤放大器的发展有重要意义. 关键词： 光子晶体光纤 模场面积 弯曲损耗 限制损耗     

线圈型全光纤偏振器的研究

本文采用等效电流法对线圈型全光纤偏振器进行了分析计算.对应于保偏光纤中两正交传输基模的消光比,提出了一种分析保偏光纤弯曲损耗的新方法,这种方法基于将保偏光纤两个不同偏振模式分别等效为两个普通圆光纤的基模,等效参数通过测量不同偏振模式的模场半径来确定.实验证明这种理论计算方法与实验结果一致.最终,我们研制出的线圈型光纤偏振器在1.31μm工作波长下,实测消光比达30dB以上,工作偏振模式插入损耗≤3dB.     

Bending dual-core photonic crystal fiber coupler

In this paper, we systematically study a designed structure of a bending dual-core photonic crystal fiber (PCF). We propose the controllable wavelength-selective coupling PCF. This coupler allows highly accurate control of the filtering wavelength. The different wavelengths can be selected by controlling the bending radius of the fiber. Coupling characteristics of novel bending wavelength-selective coupling PCF are evaluated by using a vector finite element method and their application to a multiplexer demultiplexer (MUX–DEMUX) based on the novel coupler is investigated. When the fiber length is 4168 μm, the bending radius of PCF couplers for 1.48/1.55 μm, 1.3/1.55 μm, 0.98/1.55 μm, and 0.85/1.55 μm is calculated, respectively, and the beam propagation analysis is performed. Different from the traditional wavelength-selective coupling PCF, the dual-core PCF is bent and it can realize the separation of multiple wavelengths.     

近场扫描光学显微镜中一种新的切向力检测系统

在近场扫描光学显微镜（ＮＳＯＭ）［１］中,近场距离控制一般采用切向力控制法。检测切向力有两种方法：光学检测法和非光学检测法。目前普遍采用非光学检测法,基本上是采用压电陶瓷管控制探针和样品的距离。本文提出一种新的切向力检测系统,利用双压电片实现近场距离控制。实验结果表明,检测灵敏度大大提高,扫描力显微（ＳＦＭ）像的分辨率可达纳米量级。     

FABRICATION AND APPLICATION OF NEAR-FIELD OPTICAL FIBRE PROBE

In this paper, the fabrication of a large cone angle near-field optical fibre probe, using the two-step chemical etching method and bent probe, is introduced, and the controlling parameters of the coated Cr－Al film at the probe tip are presented. The scanning electron microscopy images display that the tip diameter of the uncoated large cone angle fibre probe obtained is less than 50nm, the cone angle over 90°, and the diameter of light aperture at the coated probe tip is less than 100nm. The measured results of the optical transmission efficiency for various probe tips show that the uncoated straight optical fibre probe, film-coated straight probe and film-coated bent probe are 3×10^-1, 2×10^-3, and 1×10^-4 times that of the flat fibre probe, respectively. In addition, the force images and near-field optical images of a standard sample are acquired using a large cone angle and film-coated bent probe.     

Real-time measurements of sliding friction and elastic properties of ZnO nanowires inside a scanning electron microscope

A real-time nanomanipulation technique inside a scanning electron microscope (SEM) has been used to investigate the elastic and frictional (tribological) properties of zinc oxide nanowires (NWs). A NW was translated over a surface of an oxidised silicon wafer using a nanomanipulator with a glued atomic-force microscopic tip. The shape of the NW elastically deformed during the translation was used to determine the distributed kinetic friction force. The same NW was then positioned half-suspended on edges of trenches cut by a focused ion beam through a silicon wafer. In order to measure Young’s modulus, the NW was bent by pushing it at the free end with the tip, and the interaction force corresponding to the visually observed bending angle was measured with a quartz tuning fork force sensor.     

中红外空心Bragg光纤的制备及在气体传感中的应用

空心Bragg光纤可广泛用于气体传感, 但要求它的传输通带处于中红外波段, 以便与待测气体的基频吸收峰匹配. 本文提出了空心Bragg光纤传输通带的一种设计方法与波长控制工艺, 可以实现传输通带在2.5-12 μ m内任意波长的空心Bragg光纤的制备. 实验制备出一阶传输通带分别在10.6 μ m和 3.3 μ m的光纤样品, 利用截断法测量出其一阶传输通带损耗分别为5.9 dB/m和8.8 dB/m. 利用在传输通带在3.3 μ m的样品中注入和排出甲烷/氮气混合气体, 观察到了光纤样品透射谱随注入气体浓度的变化, 并用指数稀释法初步测量了该系统的浓度探测极限约为26 ppm, 验证了该光纤应用于气体传感的可行性.     

采用DDS的近场扫描光学显微镜探针-样品的纳米距离检测

近场扫描光学显微术中, 近场距离的检测和控制是需要解决的核心技术之一. 本文研究了基于DDS驱动的压电传感器, 在一个压电陶瓷片上, 电极被分成相同的两部分, 分别用于振动驱动和振幅检测. 近场扫描的光纤探针固定于此压电陶瓷片上. 振动驱动信号采用DDS, 在样品的远场时, 可以通过频率扫描得到误差在0.006 Hz以内的压电陶瓷片谐振频率驱动信号, 而当光纤探针处于样品的近场距离之内时, 压电陶瓷片的谐振频率偏离驱动信号频率, 振幅明显减小, 从而检测出近场距离. 高精度振动驱动源DDS和高灵敏度压电传感器的采用提高了检测灵敏度和工作稳定性.     

Multifiber optical catheter with bending control of distal end: Applications of Raman biospectroscopy

This work demonstrates a multifiber optical catheter with bending control of the distal end, whose main use is to collect Raman signal for biospectroscopy. Also, a method for fiber background subtraction is presented, allowing removal of fiber emission peaks from gross Raman spectrum. The fiber optic catheter with seven fiber optics wrapped up in a resin and a biocompatible flexible teflon tube has been modified to incorporate a mechanical device with gauntlet, which allows bending of the distal extremity to access a desired location obeying the anatomy of the organ. The mechanical device (gauntlet) was built halfway from the catheter proximal excitation tip, allowing the bending of the distal end of about 38 mm diameter. Dispersive Raman spectra at 785 nm excitation wavelength from samples were measured without and with bending (from 120 mm decreasing to 14 mm) of the distal end of the catheter. An optical catheter without the gauntlet was used as a reference. Results demonstrated that both catheters (with bending mechanism and standard one) had about the same Raman signal when the device was bent semicircularly to 38 mm diameter (bending limit for the mechanism), with negligible implication to the Raman signal-to-noise relation (SNR) from sample. When both catheters were bent in a full turn, the Raman signal decreased to about 40% when bending reached 14 mm diameter, mainly due to losses introduced by changes in the fiber total internal reflection. The background removal was efficient, with minimum residual from fiber peaks. This optical catherer could be very useful in laser diagnosis and clinical applications, introducing a way to control the fiber tip position and angle on the tissue or organ. Published in Zhurnal Prikladnoi Spektroskopii, Vol. 74, No. 1, pp. 97–102, January–February, 2007.     

Piezoelectric Current Generation in Wurtzite GaAs Nanowires

Generation of electric current is observed when GaAs nanowires with wurtzite crystal structure are bent by the probe of an atomic force microscope. The current originates from a piezo active phase in the nanowires due to the piezoelectric effect. Increasing of the piezo‐potential in bent nanowires enhances tunneling through the probe–nanowire Schottky barrier due to the thermionic field emission. Laser illumination amplifies short‐circuit current pulses by two orders of magnitude from 9 pA to 1 nA due to the piezo‐phototronic effect. Utilization of such piezo‐phototronic effect in GaAs nanowires is a solution to accelerate the efficiency of hybrid energy sources “piezoelectric nanogenerator ? solar cell” comprised of III–V nanowires.     

新型三角芯抗弯曲大模场面积光子晶体光纤

提出了一种新型三角芯抗弯曲大模场面积光子晶体光纤.该结构采用单一尺寸的圆形空气孔, 降低了制作难度.在波长1.064 μm处, 在平直状态和弯曲半径为30 cm时, 模场面积分别为1386 μm²和1153 μm², 弯曲带来的模场面积减少量仅为16.85%. 当弯曲半径为30 cm时, 基模的损耗为0.087 dB/m, 二阶模的损耗大于1.5 dB/m, 大的损耗差有效保证了光纤单模运转.此外, 弯曲半径30 cm时, 弯曲方向角扩展至±180°, 光纤弯曲不再受弯曲方向的限制. 所设计的光纤结构具有大模场面积、小的模场面积减少量、 低的弯曲损耗以及低的弯曲方向敏感度等优势, 为小型化、集成化高功率激光传输及光纤激光器和放大器的研究奠定了基础. 关键词： 光子晶体光纤 大模场面积 抗弯曲 弯曲方向角