Rheotens-mastercurves and elongational viscosity of polymer melts

In a Rheotens experiment, the tensile force needed for elongation of an extruded filament is measured as a function of the draw ratio. For thermo-rheologically simple polymer melts, the existence of Rheotens-mastercurves was proved by Wagner, Schulze, and Göttfert (1995). Rheotens-mastercurves are invariant with respect to changes in melt temperature and changes in the average molar mass. By use of purely viscous models, we convert Rheotens-mastercurves of a branched and a linear polyethylene melt to elongational viscosity as a function of strain rate. The resulting elongational viscosity from constant force extension experiments is found to be in general agreement with what is expected as steady-state viscosity of polyethylene melts measured in either constant strain-rate or constant stress mode.Dedicated to Prof. Dr. J. Meissner on the occasion of his retirement from the chair of Polymer Physics at the Eidgenössische Technische Hochschule (ETH) Zürich, Switzerland     

Investigation of the rheological properties of short glass fiber-filled polypropylene in extensional flow

The behavior of short glass fiber–polypropylene suspensions in extensional flow was investigated using three different commercial instruments: the SER wind-up drums geometry (Extensional Rheology System) with a strain-controlled rotational rheometer, a Meissner-type rheometer (RME), and the Rheotens. Results from uniaxial tensile testing have been compared with data previously obtained using a planar slit die with a hyperbolic entrance. The effect of three initial fiber orientations was investigated: planar random, fully aligned in the stretching flow direction and perpendicular to it. The elongational viscosity increased with fiber content and was larger for fibers initially oriented in the stretching direction. The behavior at low elongational rates showed differences among the various experimental setups, which are partly explained by preshearing history and nonhomogenous strain rates. However, at moderate and high rates, the results are comparable, and the behavior is strain thinning. Finally, a new constitutive equation for fibers suspended into a fluid obeying the Carreau model is used to predict the elongational viscosity, and the predictions are in good agreement with the experimental data.     

Elongational properties and molecular structure of polyethylene melts

Summary The viscosity and the recoverable strain in the steady state of elongation have been measured on several polyethylenes of different molecular structures. The elongational viscosity as a function of tensile stress runs through a more or less pronounced maximum in the nonlinear range whereas in the linear range the Trouton viscosity is reached. For low density polyethylenes it could be demonstrated that the maximum of the steady-state elongational viscosity and the elasticity expressed by the steady-state compliances in shear and tension sensitively increase if the molecular weight distribution is broadened by the addition of high molecular weight components. A variation of the weight average molecular weight does only shift the elongational viscosity curve but leaves its shape unchanged. Two of the four high density polyethylenes investigated do not show a maximum of the steady-state elongational viscosity, for the others it is less pronounced than in the case of low density polyethylenes. The influence of branching on the elongational behaviour of polyethylene melts in the steady-state and the transient region is qualitatively discussed.With 11 figures and 4 tables     

Comparison of viscous and elastic properties of polyolefin melts in shear and elongation

Viscous and elastic properties of a linear polypropylene (PP) and a long-chain branched low-density polyethylene (LDPE) have been investigated by creep and creep–recovery experiments in shear and elongation. The data obtained verify the ratios between the linear values of the viscosities and the steady-state elastic compliances in shear and elongation predicted by the theory of linear viscoelasticity. In the nonlinear range, no simple correlation between the viscous behaviour in shear and elongation exists. The elongational viscosity of the PP decreases with increasing stress analogously to the shear thinning observed; the linear range extends to higher stresses in elongation than in shear, however. The LDPE shows thinning in shear and strain hardening in elongational flow. For the LDPE, a linear steady-state elastic tensile compliance corresponding to one third of the linear steady-state elastic compliance in shear was determined. For the PP, this theoretically predicted value is approximately reached. Analogous to the viscous behaviour, the linear range extends to higher stresses in elongation than in shear. For both materials, the steady-state elastic compliances in the nonlinear range decrease with increasing stress in shear as well as in elongation. However, the decrease in elongation is more pronounced.     

Comparison of the elongational behaviour of a polyethylene melt at constant stress and constant strain rate

Summary Two different apparatuses for measuring the elongational behaviour of polymer melts at constant tensile stress and constant elongational strain rate are described. Measurements on a low density polyethylene were carried out up to stretching ratios of 400. The homogeneity of sample deformation in both test methods was sufficient to reach a steady-state of elongational flow where the tensile stress and the strain rate as functions of time are constant. By unloading the molten rod the recoverable strain can be determined at any state of deformation. The recoverable strain increases with growing deformation and reaches a constant value in the steady-state. The elongational viscosity calculated from the rate of viscous flow agrees with the Trouton viscosity in the case of very small deformations only. With growing deformation the elongational viscosity increases up to a constant value in the steady-state which is greater than the Trouton viscosity by about a factor of six at measured strain rates of 0.03 s^–1 and 0.1 s^–1, respectively. The elongational viscosity and the recoverable strain in the steady-state measured with the two different test methods under the same experimental conditions are in good agreement.

---

Zusammenfassung Zwei verschiedene Apparaturen zur Untersuchung des Dehnverhaltens von Polymerschmelzen unter konstanter Zugspannung und konstanter Dehngeschwindigkeit werden beschrieben. An einem Polyäthylen niedriger Dichte wurden Messungen bis zu Verstreckgraden von 400 durchgeführt. Die ausreichend homogene Probenverformung erlaubt in beiden Versuchsführungen das Erreichen eines stationären Dehnfließens mit zeitlich konstanter Zugspannung und Dehngeschwindigkeit. Durch Entlasten des Schmelzestranges ist der reversible Dehnungsanteil für jeden Verformungszustand direkt zu messen. Die reversible Dehnung steigt mit wachsender Dehnverformung an, bis sich im stationären Bereich ein konstanter Wert einstellt. Die aus der Geschwindigkeit des viskosen Dehnfließens berechnete Dehnviskosität stimmt nur für den Grenzfall kleiner Deformationen mit der Trouton-Viskosität überein. Mit wachsender Dehndeformation steigt die Dehnviskosität bis zu einem Gleichgewichtswert an, der bei den gemessenen Dehngeschwindigkeiten von 0,03 s^–1 und 0,1 s^–1 um etwa einen Faktor 6 über dem Wert der Trouton-Viskosität liegt. Die unter gleichen Versuchsbedingungen mit beiden Apparaturen bestimmten Dehnviskositäten und reversiblen Dehnungen im stationären Bereich stimmen überein.

---

---

Parts of this paper were presented at the VII^th Internat. Congress on Rheology, Gothenburg, Sweden.

---

With 10 figures and 2 tables     

Modeling strain hardening of polydisperse polystyrene melts by molecular stress function theory

The strain hardening of blends of polystyrene (PS) and ultra-high molecular weight polystyrene (UHMW-PS) in elongational flow is modeled by the molecular stress function (MSF) theory. Assuming that the ratios of strain energies stored in polydisperse and monodisperse polymers are identical for linear and nonlinear deformations, the value of the only non-linear parameter of the theory in extensional flows, the maximum molecular stress f_max, can be determined and is shown to be related to steady-state compliance J_e0. Using only linear-viscoelastic data, the elongational viscosity of PS/UHMW-PS blends is consistently predicted by the MSF theory.     

Elongational viscosity by fiber spinning

Isothermal melt, fiber-spinning was recently analyzed by means of a nonlinear, integral, constitutive equation that incorporates shear history effects, spectrum of relaxation times, shear-thinning, and extension thinning or thickening when either the drawing force or the draw ratio is specified. The predictions agreed with experimental data on spinning of polystyrene, low-density polyethylene, and polypropylene melts. The predicted apparent elongational viscosity along the threadline (which, as shown in this work, must be identical to that measured experimentally by fiber spinning type of elongational rheometers) is compared with the true elongational viscosity predicted by the same constitutive equation under well-defined experimental conditions of constant extension rate, independent of any strain history. It is concluded that the apparent elongational viscosity, as measured by fiber-spinning, approaches the true elongational viscosity at low Weissenberg numbers (defined as the product of the liquid's relaxation time multiplied by the extension rate). At moderate Weissenberg numbers, the two viscosities may differ by an order of magnitude and their difference grows even larger at high Weissenberg numbers.     

Effect of a controlled pre-deformation history on extensional viscosity of dilute polymer solutions

We use a modified filament stretching rheometer to quantify the influence of a known controlled pre-shear history on the transient extensional viscosity of a dilute polymer solution. Two different types of pre-deformation are explored; both influence the subsequent stretching significantly, albeit in opposite ways. Small-amplitude oscillatory straining parallel to the direction of stretching enhances strain hardening and accelerates the tensile stress growth toward the steady-state value. Conversely, steady torsional shearing orthogonal to the direction of stretching retards strain hardening and results in a delayed approach to steady-state elongational flow. In both cases, the final steady-state extensional viscosity is the same as that observed with no pre-shearing. Calculations using a finitely extensible nonlinear elastic Peterlin dumbbell model qualitatively capture the trends observed in experiments, enabling interpretation of these observations in terms of the degree of polymer chain stretching imposed by the flow before extensional stretching.     

液晶高分子-各向异性流体挤出拉伸分岔研究

应用共转导数型本构方程研究了液晶高分子纺丝挤出过程的拉伸黏度,应用计算机符号运算软件 Maple得出解析表达式,拉伸黏度与拉伸率之间关系(随剪切速率变化)表明存在分岔现象,得出拉伸黏度显著高于相应的剪切黏度,解释了液晶高分子熔体挤出时不发生挤出胀大的物理机制．     

Rheological properties of long glass fiber filled polypropylene

Long glass fiber-filled polypropylene (PP) composites are produced by pultrusion, and the extrudate is cut at different lengths producing composites containing long fibers of controlled length. The rheological properties of such composites in the molten state have been studied using different rheometers. A capillary rheometer has been constructed and mounted on a molding-injection machine. The shear viscosity of filled PP determined from the capillary rheometer, after corrections for entrance effects, was found to be very close to that of unfilled PP. However, large excess pressure losses at the capillary entrance were observed and these data have been used to obtain an apparent elongational viscosity. The apparent elongational viscosity was shown to be considerably larger than the shear viscosity for PP and filled PP, and it increased markedly with fiber length and fiber content. Rotational rheometers with a parallel-plate geometry were used to investigate the viscoelastic properties of these composites and their behavior was found to be non-linear, exhibiting a yield stress. A model is proposed to describe the shear viscosity from a solid-like behavior at low stresses to fluid-like behavior at high shear stresses taking into account fiber content and orientation. A modified model, proposed for elongational flow, describes relatively well the apparent elongational data.     

Measurements and model predictions of transient elongational rheology of polymeric nanocomposites

Transient elongational rheology of two commercial-grade polypropylene (PP) and the organoclay thermoplastic nanocomposites is investigated. A specifically designed fixture consisting of two drums (SER Universal Testing Platform) mounted on a TA Instruments ARES rotational rheometer was used to measure the transient uniaxial extensional viscosity of both polypropylene and nanoclay/PP melts. The Hencky strain rate was varied from 0.001 to 2 s^− 1, and the temperature was fixed at 180°C. The measurements show that the steady-state elongational viscosity was reached at the measured Hencky strains for the polymer and for the nanocomposites. The addition of nanoclay particles to the polymer melt was found to increase the elongation viscosity principally at low strain rates. For example, at a deformation rate of 0.3 s^− 1, the steady-state elongation viscosity for polypropylene was 1.4 × 10⁴ Pa s which was raised to 2.8 × 10⁴ and 4.5 × 10⁴ Pa s after addition of 0.5 and 1.5 vol.% nanoclay, respectively. A mesoscopic rheological model originally developed to predict the motion of ellipsoid particles in viscoelastic media was modified based on the recent developments by Eslami and Grmela (Rheol Acta 47:399–415, 2008) to take into account the polymer chain reptation. We show that the orientation states of the particles and the rheological behavior of the layered particles/thermoplastic hybrids can be quantitatively explained by the proposed model.     

Tensile properties of an extruded polyethylene-melt

Summary Isothermal continuous stretching experiments with a Rheotens apparatus were carried out on an extruded polyethylene melt. Measurements of the tensile force, the thread velocity and the thread profiles for various mass flow rates resulted in the determination of the elongational viscosity as a function of the strain rate and the deformation time. It was found that the deformation time is a more suitable general parameter than the strain rate for the characterization of the elongational viscosity of extruded polymer melts.

---

Zusammenfassung Experimente zum isothermen Schmelzspinnen wurden mit dem Rheotens an einer extrudierten Polyäthylenschmelze durchgeführt.Messungen von Abzugskraft, Abzugsgeschwindigkeit und Querschnittsprofil des extrudierten Stranges bei variierenden Ausstößen führten zur Bestimmung der Dehnviskosität als Funktion von Dehngeschwindigkeit und Deformationszeit. Es konnte nachgewiesen werden, daß die Deformationszeit besser als die Dehngeschwindigkeit zur Charakterisierung der Dehnviskosität von extrudierten Schmelzen geeignet ist.

---

---

Vortrag, gehalten auf der Jahrestagung der Deutschen Rheologischen Gesellschaft e.V., Universität Dortmund, 9. bis 11. März 1977.

---

With 8 figures     

Uniaxial elongational flow effects and morphology development in LDPE/phosphate glass hybrids

Shear and elongational viscosity measurements were performed on low-density polyethylene/phosphate glass (LDPE/Pglass) hybrid materials in the liquid state. Under shear deformation, the hybrids with low concentrations of Pglass showed a Newtonian region at low frequencies, followed by shear-thinning behavior at high frequencies. High Pglass concentrations displayed shear-thinning behavior over the whole range of frequencies studied. Deviations from the log-additivity rule for viscosity were found to be compositionally dependent and generally indicated an immiscible mixture. The elongational viscosity of the hybrids increased at very low Pglass concentrations (1–2 vol.% Pglass) and then was drastically reduced at higher concentrations (i.e., >10 vol.% Pglass). In addition, elongational flow was found to induce the formation of Pglass fibrils in hybrids containing at least 10 vol.% Pglass. This was correlated to the elongational capillary number; the critical elongational capillary number was estimated to be 0.22. The elongational deformation was also found to greatly increase the overall crystallinity of the system due to molecular orientation of the LDPE polymer chains as confirmed by wide angle X-ray diffraction. A critical composition of 5 vol.% Pglass was found to be the point at which LDPE hybrid rheological properties, molecular orientation, and morphology changed drastically.     

Constitutive relationships for polymeric materials with power-law distributions of relaxation times

The linear relaxation modulus of polydisperse polymer melts and solutions can often be approximated by a power law,ct ^–m over some range of time,t. If, in addition, the nonlinear rheology is given by a separable integral equation, with a strain-dependent factor typical of those observed experimentally, then some commonly observed empirical rules and equations can be readily derived as approximations, namely the Cox-Merz relationship between complex viscosity and steady-state shear viscosity, Bersted's predictions of steady shear stress and first normal-stress difference from a truncated spectrum of linear relaxation times, and the observation of Koyama and coworkers that the ratio of the nonlinear to the linear time-dependent elongational viscosity is independent of strain rate, over a range of strain rates outside the linear regime.     

Isothermal elongational behavior of liquid-crystalline polymers and LCPs based blends

The rheological behavior of two flexible thermoplastics, Nylon-6 (Ny) and bisphenol-A polysulfone (PSu), and two wholly aromatic liquid crystalline polymers, Vectra-A900 (VA) and Vectra-B950 (VB), as well as that of Ny/VB and PSu/VA blends with 10% LCP, has been investigated by the use of capillary viscometers equipped with cylindrical dies having different length-to-diameter ratios. The elongational viscosity of all materials was calculated, from the results of isothermal measurements carried out at 290°C, by means of the Cogswell's analysis, based on the estimation of the pressure drop due to the converging flow at the die inlet. The behavior in elongational flow was compared with the rheological behavior in shear flow conditions. It was found that the elongational viscosities of VA and VB are very large and account for a fairly marked pressure drop at the die entrance, due to the orientation of the LCP domains taking place in the converging flow zone. For these materials, the ratio of the elongational viscosity to the Newtonian shear viscosity is up to two orders of magnitude higher than the value expected on the basis of the Trouton rule. For the flexible resins, the Trouton ratio is 3 and ca. 3–10, are common values for high molar mass linear polymers. The addition of 10% LCP into the flexible resins strongly increases their elongational viscosity and makes the blends resemble neat LCPs in their extensional flow behavior. In shear flow, on the contrary, the addition of LCP was shown to induce a marked reduction of the melt viscosity, even when, as for the Ny/VB blend, the LCP is more viscous than the matrix.     

Modelling elongational and shear rheology of two LDPE melts

Experimental data of two low-density polyethylene (LDPE) melts at 200°C for both shear flow (transient and steady shear viscosity as well as transient and steady first normal stress coefficient) and elongational flow (transient and steady-state elongational viscosity) as published by Pivokonsky et al. (J Non-Newtonian Fluid Mech 135:58–67, 2006) were analysed using the molecular stress function model for broadly distributed, randomly branched molecular structures. For quantitative modelling of melt rheology in both types of flow and in a very wide range of deformation rates, only three nonlinear viscoelastic material parameters are needed: Whilst the rotational parameter, a ₂, and the structural parameter, β, are found to be equal for the two melts considered, the melts differ in the parameter describing maximum stretch of the polymer chains.     

Modeling elongational viscosity of blends of linear and long-chain branched polypropylenes

To enhance the melt strength of a conventional linear polypropylene (L-PP), blends with a long-chain branched polypropylene (LCB-PP) were produced by adding 2, 5, 10, 25, 50, and 75 wt% of LCB-PP to L-PP and mixing in a twin screw extruder. It was found that, already, an addition of 10% or less of LCB-PP to L-PP leads to significant strain hardening. Elongational viscosity data of L-PP and LCB-PP and those of their blends were analyzed by the use of the molecular stress function (MSF) theory. While L-PP is characterized by the MSF parameter, β=1 (typical for linear melts), and shows very little chain stretch (), melt elongational behavior of LCB-PP is characterized by the MSF parameters, β=2 (typical of LCB melts), and (which corresponds to a maximum stretch of molecular chains by a factor of 15). By extruding LCB-PP, a refining effect is observed similar to the refining effects seen in low density polyethylene (LDPE), which reduces the steady-state elongational viscosity and reduces to 121. A second-order mixing rule for the fractional relaxation moduli, g _i , was found to show good agreement with the linear-viscoelastic data of the blends. To simulate the elongational viscosities of the L-PP/LCB-PP blends, a similar second-order mixing rule was used for the MSF parameter, β, while a first-order mixing rule was found to be appropriate for . This allows for a quantitative prediction of the time-dependent elongational viscosities of all L-PP/LCB-PP blends on the basis of the linear and nonlinear parameters of the mixing components L-PP and LCB-PP only. Comparison between the steady-state elongational viscosities as obtained from creep experiments shows good agreement with predictions.