Kinetic studies on the hydrogenation of nitrate in water using Rh/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and Rh-Cu/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

Liquid-phase reduction NO ₃ ⁻ using monometallic and bimetallic catalysts (5% Rh/Al₂O₃, 5% Rh-0.5% Cu/Al₂O₃, 5% Rh-1.5% Cu/Al₂O₃, 5% Rh-5% Cu/Al₂O₃ and a physical mixture of 5% Rh/Al₂O₃ and 1.5% Cu/Al₂O₃) was studied in a slurry reactor operating at atmospheric pressure. Kinetic measurements were performed for a low concentration of nitrate (0.4 × 10⁻³−3.2 × 10⁻³ mol dm⁻³) and the temperature range 293–313 K. From the experimental data, it was found that the reduction of nitrate is first order with respect to nitrate. On the basis of the rate constants, the apparent activation energy was established using a graphic method. Published in Russian in Kinetika i Kataliz, 2007, Vol. 48, No. 6, pp. 881–886. This article was submitted by the authors in English.     

Hydrogenolysis of glycerol to propanediols over heteropolyacids promoted AgCu/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

Various amounts and different types of heteropolyacids promoted 5Ag15Cu/Al₂O₃ catalysts were prepared by impregnation method and analyzed through many techniques. The synthesized catalysts were evaluated for hydrogenolysis of glycerol to propanediols. The results demonstrated that heteropolyacids loading facilitated the reduction, promoted the dispersion, enhanced the acidity, and increased Broensted acid sites of the AgCu catalysts, which benefited the generation of 1,3-propanediol. Compared with phosphotungstic acid and phosphomolybdic acid, silicotungstic acid promoted AgCu catalyst had a better performance for 1,3-propanediol due to the better Cu dispersion and higher Broensted acidity. In addition, when the reaction was performed at 220 °C under 3.5 MPa for 8 h, the chosen 5Ag15Cu-10HSiW/Al₂O₃ achieved a 69.6% glycerol conversion with 35.6% 1,2-propanediol selectivity and 21.5% 1,3-propanediol selectivity.     

Co-Mo/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and Ni-W/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts: Potential and prospects for use in hydrotreating of light cycle oil from catalytic cracking

Со-Мо/Al₂O₃ and Ni-W/Al₂O₃ catalysts were tested in hydrotreating of light cycle oil from catalytic cracking, of the straight-run gasoil, and of their mixture under typical hydrotreating conditions used in industry. The catalysts prepared using PMo₁₂ and PW₁₂ heteropoly acids exhibit high catalytic activity. The Со-Мо/Al₂O₃ catalyst is more active in hydrodesulfurization and hydrogenation of olefin and diene hydrocarbons, whereas the Ni-W/Al₂O₃ catalysts are more active in hydrogenation of mono- and polycyclic aromatic hydrocarbons. Comparison of the quality characteristics of the hydrogenizates obtained with the requirements of the technical regulations shows that the required levels of the sulfur content and cetane number of the hydrogenizates at practically accessible process parameters can be reached for mixtures of the straight-run gasoil and light cycle oil from catalytic cracking with high content of the latter component only when the process with the Со-Мо/Al₂O₃ system and Ni-W/Al₂O₃ catalysts is performed in two steps.     

One-pot synthesis of Nb-modified Al<Subscript>2</Subscript>O<Subscript>3</Subscript> support for NiMo hydrodesulfurization catalysts

The effect of Nb as a support modifier on the NiMo₆/Al₂O₃–Nb₂O₅(x) (x?=?0, 1, 4, and 8?wt% Nb) catalysts was studied. The supports were prepared by one-pot coprecipitation from soluble precursors. The XRF analysis of the catalysts showed that the contents of Mo and Ni increased slightly with the presence of Nb. Micropore area and pore volume augmented importantly with Nb content, resulting in pore diameters between 5.3 and 9.3?nm. XPS analysis showed that the presence of Nb decreases the active metal–support interaction, improving the Mo and Ni sulfidation degree. The Raman spectra of sulfided catalysts suggested an increase in the number of layers of MoS₂ in the presence of Nb. Generally, the thiophene HDS activity at normal pressure of sulfided NiMo₆/Al₂O₃–Nb₂O₅(8) was greater than that of the sulfided catalysts with x?=?0, 1, and 4?wt% Nb, which can be attributed to the Nb promotion that would have an effect on the type of active site (Brønsted or Lewis acidic sites), since the number of sites by CO chemisorption for sulfided NiMo₆/Al₂O₃–Nb₂O₅(x) did not show correlation with the catalytic activity. The high-pressure HDS activity of dibenzothiophene was also greater in the presence of Nb, and the hydrogenation route was preferred for the Nb-promoted solid, while the unpromoted one showed a larger yield of direct desulfurization products.

Open image in new window

     

Gold catalysts supported on ZnO/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> for low-temperature CO oxidation

Gold catalysts with loadings ranging from 0.5 to 7.0 wt% on a ZnO/Al₂O₃ support were prepared by the deposition–precipitation method (Au/ZnO/Al₂O₃) with ammonium bicarbonate as the precipitation agent and were evaluated for performance in CO oxidation. These catalysts were characterized by inductively coupled plasma-atom emission spectrometry, temperature programmed reduction, and scanning transmission electron microscopy. The catalytic activity for CO oxidation was measured using a flow reactor under atmospheric pressure. Catalytic activity was found to be strongly dependent on the reduction property of oxygen adsorbed on the gold surface, which related to gold particle size. Higher catalytic activity was found when the gold particles had an average diameter of 3–5 nm; in this range, gold catalysts were more active than the Pt/ZnO/Al₂O₃ catalyst in CO oxidation. Au/ZnO/Al₂O₃ catalyst with small amount of ZnO is more active than Au/Al₂O₃ catalyst due to higher dispersion of gold particles.     

Effect of cerium dioxide on the properties of monolithic CuO-ZnO-CeO<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/cordierite catalysts in methanol decomposition

Cerium dioxide as a component of CuO-ZnO-CeO₂/Al₂O₃/cordierite catalysts stabilizes their action in the decomposition of methanol by preventing carbon deposition on the surface and facilitating hydrogen formation with selectivity and yield in the range 85–96%. The optimal indices for this reaction are obtained for a CeO₂-CuO/Al₂O₃/cordierite sample prepared using an ammonium precursor for cerium, (NH₄)₂Ce(NO₃)₆. This catalyst displays enhanced reductive capacity relative to the analogous CeO₂-CuO composition prepared using Ce(NO₃)₃·6H₂O.     

Reactivation of CoMo/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> hydrotreating catalysts with chelating agents

Effect of various chelating components, multibasic carboxylic acids and glycols, used to prepare hydrotreating catalysts on the activity regeneration of calcined hydrotreating catalysts was studied. Reactivated catalyst samples were tested in a model reaction of hydrodesulfurization of dibenzothiophene. It was shown that the treatment of calcined catalysts with the chelating components leads to an increase in the catalytic activity. The best catalytic characteristics are observed for the catalyst reactivated with a solution containing citric acid and triethylene glycol.     

Selective oxidation of carbon monoxide in hydrogen-containing gas on CuO-CeO<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts prepared by surface self-propagating thermal synthesis

The CuO-CeO₂/Al₂O₃ catalysts for the selective oxidation of CO in hydrogen-containing mixtures were prepared by surface self-propagating thermal synthesis (SSTS) with the use of cerium nitrate Ce(NO₃)₃, the ammonia complex of copper acetate [Cu(NH₃)₄](CH₃COO)₂, and citric acid C₆H₈O₇ as a fuel additive. The effect of the C₆H₈O₇/Ce(NO₃)₃ molar ratio on the catalyst activity and selectivity for oxygen was studied. The catalyst samples were studied by X-ray diffraction (XRD) analysis, temperature-programmed reduction (TPR-H₂), IR spectroscopy of adsorbed CO, and transmission electron microscopy (TEM). It was found that an increase in the C₆H₈O₇/Ce(NO₃)₃ ratio resulted in an increase in the degree of dispersion of the resulting CeO₂ phase. The greatest amount of dispersed CuO particles, which are responsible for catalytic activity in the oxidation of CO, was formed at C₆H₈O₇/Ce(NO₃)₃ = 1.     

Preparation and characterization of supports with a synthesized layer of catalytic filamentous carbon: IV. Synthesis of carbon nanofibers on a Co/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyst

A comparative study of the synthesis of carbon layers, including catalytic filamentous carbon, on the surface of various alumina modifications was made. The synthesis was performed by the pyrolysis of alkanes (a propane-butane mixture) on Co/Al₂O₃ supported catalysts. The texture characteristics (specific surface area and pore structure) of the starting supports and adsorbents with a synthesized carbon layer were studied. The surface morphology of Co/Al₂O₃ catalysts and the synthesized carbon deposits was studied by scanning electron microscopy. It was found that carbon nanofibers were formed only on the catalysts prepared by the homogeneous precipitation of Co compounds onto the surface of macroporous α-Al₂O₃, whereas carbon deposits on mesoporous aluminum oxides did not exhibit a pronounced fibrous structure. The applicability of C/Co/Al₂O₃ carbon-containing adsorbents to the immobilization of the nitrile hydratase enzyme and the preparation of a biocatalyst for acrylonitrile hydration to acrylamide was considered.     

Composition of the gas phase over Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and the enthalpies of atomization of AlO,Al<Subscript>2</Subscript>O,and Al<Subscript>2</Subscript>O<Subscript>2</Subscript>

The A1, O, AlO, A1₂O, Al₂O₂, WO₂, and WO₃, partial pressures in the vapor over Al₂O₃ in a tungsten Knudsen effusion cell between 2300 and 2600 K were derived from A1⁺, O⁺, AlO⁺, A1₂O⁺, Al₂O₂⁺, WO₂⁺, and WO₃⁺, ion intensities. The mass spectrometer was calibrated against the equilibrium constant of the WO₃(g) = WO₂(g) + O(g) reaction. Refined values of the ionization cross sections of AlO and A1₂O₂ were used in the partial pressure calculations. The enthalpies of atomization of aluminum suboxides were determined to be Δ_at H ^o(AlO, g, 0) = 510.7 ± 3.3 kJ mol⁻¹, Δ_at H ^o(Al₂O, g, 0) = 1067.2 ± 6.9 kJ mol⁻¹, and Δ_at H ^o(Al₂O₂, g, 0) = 1556.7 ± 9.9 kJ mol⁻¹.     

Investigation of macro-/mesoporous Re<Subscript>2</Subscript>O<Subscript>7</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts prepared by a particle-template method for butylene metathesis

Macro-/mesoporous Al₂O₃ supports were prepared by using monodisperse polystyrene (PS) microspheres as a template. The pore volume and BET surface area of the Al₂O₃ supports increased considerably with increasing amounts of the PS microspheres; further investigation showed that PS template only increased the volume of macro-pores but did not change the volume of meso-pores or micro-pores. Macro-/mesoporous Re₂O₇/Al₂O₃ metathesis catalysts were prepared through loading Re₂O₇ onto the as-prepared macro-/mesoporous Al₂O₃ supports, and their catalytic performance was tested in a fixed-bed tubular reactor using the metathesis of normal butylenes as a probe reaction. The results showed that the prepared macro-/mesoporous Re₂O₇/Al₂O₃ catalyst had high activity with consistent selectivity; propylene and pentene accounted for more than 90 wt% of the metathesis products, while the amount of ethylene plus hexane was less than 10 wt%, the majority of which was hexane. These Re₂O₇/Al₂O₃ catalysts had not only higher activity, but also longer working life span and higher tolerance to carbon residues than conventional Re₂O₇/Al₂O₃ catalysts.     

Oxidative desulfurization of thiophene derivatives with H<Subscript>2</Subscript>O<Subscript>2</Subscript> in the presence of catalysts based on MoO<Subscript>3</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> under mild conditions

The catalysts based on MoO₃/Al₂O₃ were synthesized and tested using aqueous hydrogen peroxide as the oxidant in the oxidative desulfurization of thiophene, benzothiophene (BT) and dibenzothiophene (DBT) into the corresponding sulfones. Among catalysts tested, 15%(MoO₃–WO₃)/Al₂O₃ prepared by a conventional impregnation method was considerably active for the oxidation of thiophene, BT and DBT, which could achieve higher than 99.2% conversions at lower reaction temperature (≤338 K). The use of hexadecyltrimethyl ammonium bromide as the phase-transfer reagent in small amounts could promote the reaction efficiently.     

A comparative study of Ir/Ga<Subscript>2</Subscript>O<Subscript>3</Subscript>, Pt/Ga<Subscript>2</Subscript>O<Subscript>3</Subscript>, and Ru/Ga<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts in selective hydrogenation of crotonaldehyde

Catalytic performance of gallia-supported iridium catalysts in the reaction of selective hydrogenation of crotonaldehyde in the gas phase was studied and compared to that of platinum and ruthenium catalysts. The best catalytic properties in terms of the selectivity to crotyl alcohol are shown by 5 wt % Pt/α-Ga₂O₃ and 5 wt % Ir/α-Ga₂O₃ catalysts prepared from nonchlorine precursors: Pt(acac)₂ and Ir(acac)₃, but for the 5 wt % Pt/α-Ga₂O₃ a very high selectivity of 75% at the high conversion (ca. 60%) is observed. A high selectivity of galia-supported iridium and platinum catalysts was explained by the surface reducibility of gallium oxide leading to covering (decoration) of platinum and iridium by gallium suboxides and the promoting effect of gallium.     

ZrO<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> binary oxides as promising supports for palladium catalysts of hydrodechlorination

Deposited palladium catalysts of the hydrodechlorination of 1,3,5-trichlorobenzene were studied. Pure zirconium and aluminum oxides and ZrO₂-Al₂O₃ mixtures with 1, 5, and 10 mol % Al₂O₃ prepared by coprecipitation were used as supports. Palladium was deposited by the precipitation of its hydroxide on supports. Catalysts on binary supports (ZrO₂ + 1% Al₂O₃ and ZrO₂ + 5% Al₂O₃) exhibited higher activity and stability in hydrodechlorination compared with catalysts on pure supports. The suggestion was made that the high activity and stability of these systems in hydrodechlorination was related to the formation of binary oxide in the interaction of ZrO₂ with palladium oxide at the stage of annealing of the catalyst precursor. Binary oxide, which was a center of the activation of the C-Cl bond, was simultaneously a source of active hydrogen. The presence of various palladium states in catalysts was substantiated by the temperature programmed reduction method.     

Initiation behaviour in hydrogenation of pyrolysis gasoline over presulphided Ni-Mo-Zn/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyst

A presulphided treatment was applied to the oxidic Ni-Mo-Zn/Al₂O₃ catalyst (nickel catalyst) in order to avoid thermal run-away during initiation of the hydrogenation of pyrolysis gasoline. The physico-chemical properties of the prepared oxidic nickel catalyst, the reduced and passivated (RP) nickel catalyst and the sulphided (RPS) nickel catalyst were characterised using N₂ adsorption-desorption, X-ray diffraction, temperature-programmed reduction (TPR) and X-ray photoelectron spectroscopy (XPS). The TPR results showed that the reducibility of the RP Ni-Mo-Zn/Al₂O₃ catalyst was improved over the oxidic nickel catalyst. The XPS spectra confirmed the binding energy of the RPS nickel catalyst to be higher than that of the oxidic nickel catalyst. The catalytic performance was evaluated on a fixed-bed reactor (reaction temperature between 30 °C and 70°C, at 2.8 MPa of total pressure and weight hourly space velocity of 2.0 h^?1, the volume of H₂/pyrogasoline = 200: 1). The rising temperature of the RPS nickel catalyst was almost 20°C lower than that of the oxidic nickel catalyst during the initial stage of the hydrogenation reaction. The results indicated that the RPS nickel catalyst exhibited better stability than the oxidic nickel catalyst during the start-up period, thereby providing a better selectivity in long-term operation.     

Thermal stability and catalytic properties of the composite amorphous Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-nanocrystals ZrO<Subscript>2</Subscript>

Catalytic properties in relation to the hydrogen oxidation reaction and thermal stability of materials based on the nanocomposite amorphous Al₂O₃-nanocrystalline ZrO₂ were studied.     

Ni/Al2O3 catalysts for CO methanation: Effect of Al2O3 supports calcined at different temperatures

The correlation between phase structures and surface acidity of Al2O3 supports calcined at different temperatures and the catalytic performance of Ni/Al2O3 catalysts in the production of synthetic natural gas(SNG) via CO methanation was systematically investigated. A series of 10 wt% NiO/Al2O3 catalysts were prepared by the conventional impregnation method, and the phase structures and surface acidity of Al2O3 supports were adjusted by calcining the commercial γ-Al2O3 at different temperatures(600–1200 C). CO methanation reaction was carried out in the temperature range of 300–600 C at different weight hourly space velocities(WHSV = 30000 and 120000 mL·g-1h-1) and pressures(0.1 and 3.0 MPa). It was found that high calcination temperature not only led to the growth in Ni particle size, but also weakened the interaction between Ni nanoparticles and Al2O3 supports due to the rapid decrease of the specific surface area and acidity of Al2O3 supports. Interestingly, Ni catalysts supported on Al2O3 calcined at 1200 C(Ni/Al2O3-1200) exhibited the best catalytic activity for CO methanation under different reaction conditions. Lifetime reaction tests also indicated that Ni/Al2O3-1200 was the most active and stable catalyst compared with the other three catalysts, whose supports were calcined at lower temperatures(600, 800 and 1000 C). These findings would therefore be helpful to develop Ni/Al2O3 methanation catalyst for SNG production.     

Promoted porous Co<Subscript>3</Subscript>O<Subscript>4</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts for ammonia decomposition

Transition metal catalysts have been considerably used for NH₃ decomposition because of the potential application in CO_x-free H₂ generation for fuel cells. However, most transition metal catalysts prepared via traditional synthetic approaches performed the inferior stability due to the agglomeration of active components. Here, we adopted an efficient method, aerosol-assisted self-assembly approach (AASA), to prepare the optimized cobalt-alumina (Co₃O₄-Al₂O₃) catalysts. The Co₃O₄-Al₂O₃ catalysts exhibited excellent catalytic performance in the NH3 decomposition reaction, which can reach 100% conversion at 600 °C and maintain stable for 72 h at a gaseous hourly space velocity (GHSV) of 18000 cm³ g_cat^?1 h^?1. The catalysts were characterized by various techniques including transmission electron microscope (TEM), scanning electron microscope (SEM), nitrogen sorption, temperature-programmed reduction by hydrogen (H₂-TPR), ex-situ/in-situ Raman and ex-situ/in-situ X-ray diffraction (XRD) to obtain the information about the structure and property of the catalysts. H₂-TPR and in-situ XRD results show that there is strong interaction between the cobalt and alumina species, which influences the redox properties of the catalysts. It is found that even a low content of alumina (10 at%) is able to stabilize the catalysts due to the adequate dispersion and rational interaction between different components, which ensures the high activity and superior stability of the cobalt-alumina catalysts.     

Molecular mechanism of formation of supported platinum catalysts of the Pt/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> family

Certain stages of the classical procedure for preparing aluminum-platinum catalysts, whose understanding is important from both the basic and practical viewpoints, are considered on the molecular level. Properties of both participants (active component precursor solution and oxide surface) are shown to be inhomogeneous, which can affect interaction of the components at the fixing stage. Existing views (and their evolution) on the mechanism of adsorption of platinum complexes from aqueous solutions on aluminum oxide surface are discussed. The role of chemical processes on the stage of fixing precursor on the electronic and structural properties of the supported metal is demonstrates. Strong metal-support interaction is shown to endow platinum with specific adsorption and catalytic properties in hydrocarbon transformation reactions.