Growth and spectral properties of Nd:LaVO4 crystal

This paper reports the growth and spectral properties of 3.5 at% Nd³⁺:LaVO₄ crystal with diameter of 20×15 mm² which has been grown by the Czochralski method. The spectral parameters were calculated based on Judd–Ofelt theory. The intensity parameters Ω_λ are: Ω₂=2.102×10⁻²⁰ cm², Ω₄=3.871×10⁻²⁰ cm², Ω₆=3.235×10⁻²⁰ cm². The radiative lifetime τ_r is 209 μs and calculated fluorescence branch ratios are: β₁(0.88μm)=45.2, β₂(1.06μm)=46.7, β₃(1.34μm)=8.1. The measured fluorescence lifetime τ_f is 137 μm and the quantum efficiency η is 65.6%. The absorption band at 808 nm wavelength has an FWHM of 20 nm. The absorption and emission cross sections are 3×10⁻²⁰ and 6.13×10⁻²⁰ cm², respectively.     

Flux growth of BPO4 crystals

Single crystals of BPO₄ with sizes up to 15×10×12 mm³ were grown by top-seeded solution growth method using Li₂O–Li₄P₂O₇ as fluxes. The components volatilized from the melt were characterized by the method of X-ray powder diffraction. The defects of grown crystals have also been investigated. The measured ultraviolet cutoff edge of BPO₄ was about 130 nm. Its density was 2.82 g/cm³ determined using drainage method.     

A new technique for the growth of superconducting YBa2Cu3O6 + δ crystals completely separated from flux

Growth of completely flux-separated YBa₂Cu₃O_{6 + δ} (referred to as 123 phase) crystals using a novel technique is described. The technique employs a modification of the seed pulling method commonly used in crystal growth. The crystals are grown in the temperature range of 960–1000°C using a BaCuO₂ flux. A 123 flux ratio of 1:5 is maintained. Photographs of the crystals and photomicrograph of the surfaces are presented to show complete flux-separation of the crystals measuring 6 mm × 3 mm × 1 mm. The Raman spectra recorded on the as-grown crystals show that they are in the tetragonal phase. Magnetic susceptibility measurements on crystals annealed in an oxygen atmosphere show a superconducting transition starting at 71 K. The present technique offers a possibility of growing large, completely flux-separated crystals of 123 for superconductivity research.     

Ambient-condition growth of superconducting YBa2Cu4O8 single crystals using KOH flux

YBa₂Cu₄O₈ is a stoichiometric oxide superconductor of T_c80 K. Unlike YBa₂Cu₃O_7−δ, this compound is free from oxygen vacancy or twin formation and does not have any microscopic disorder in the crystal. Doping with Ca raises its T_c to 90 K. The compound is a promising superconductor for technological application. Up to now, single crystals have not been grown without using specialized apparatus with extremely high oxygen pressure up to 3000 bar and at over 1100 °C due to the limited range of reaction kinetics of the compound. This fact has delayed the progress in the study of its physical properties and potential applications. We present here a simple growth method using KOH as flux that acts effectively for obtaining high-quality single crystals in air/oxygen at the temperature as low as 550 °C. As-grown crystals can readily be separated from the flux and exhibit a perfect orthorhombic morphology with sizes up to 0.7×0.4×0.2 mm³. Our results are reproducible and suggest that the crystals can be grown using a conventional flux method under ambient condition.     

Growth and spectral properties of Nd-doped Sr3Y(BO3)3 crystal

A new crystal of Nd³⁺:Sr₃Y(BO₃)₃ with dimension up to 25×35 mm² was grown by Czochralski method. Absorption and emission spectra of Nd³⁺: Sr₃Y(BO₃)₃ were investigated . The absorption band at 807 nm has a FWHM of 18 nm. The absorption and emission cross sections are 2.17×10⁻²⁰ cm² at 807 nm and 1.88×10⁻¹⁹ cm² at 1060 nm, respectively. The luminescence lifetime τ_f is 73 μs at room temperature     

High-quality InP grown by chemical beam epitaxy

InP films were grown by chemical beam epitaxy using trimethylindium (TMI) and pure phosphine (PH₃) in a flow control mode with hydrogen as the carrier gas, with the TMI flow rate fixed at 3 SCCM. Substrate temperatures were varied between 505 and 580°C and V/III ratios from 3 to 9. InP layers with high optical quality (intense and narrow excitonic transition lines) and high crystalline quality (narrow and symmetric X-ray diffraction peaks) could be grown only within a narrow parameter window around a substrate temperature of 545°C (δT_s ≤ 25°C) and a V/III ratio of 5.5 (δ(V/III) ≤ 2). Carrier densities of 8 × 10¹⁴ cm^-3 with mobilities of 70000 cm²/V.s measured at 77 K were obtained for growth conditions close to the edge of this parameter window towards low V/III ratios. The growth rate of inP was also clearly at its maximum in the given parameter window. Leaving the window, by changing either the growth temperature or the V/III ratio, significantly decreased the growth rate. This reduced growth rate was accompanied by a degradation in the crystalline quality. We also demonstrate that for higher TMI flow the parameter window shifts to higher growth temperatures. The InP could be doped effectively with Si in the range from 9 × 10¹⁵ to 3 × 10¹⁸ cm^-3.     

Growth of large dimension BaWO4 crystal by the Czochralski method

In this paper, polycrystalline materials of BaWO₄ were synthesized by solid-state phase method, and a single crystal of BaWO₄ was successfully grown along a and c-axis direction by using the Czochralski method. Up to 20×22×80 mm³ BaWO₄ crystal was obtained, and X-ray powder diffraction results show that the as-grown BaWO₄ crystal belongs to the scheelite structure. The effective segregation coefficients of Ba and W of the BaWO₄ crystal were measured by the X-ray fluorescence method, and the effective segregation coefficients of Ba and W were near 1. The rocking curve from (2 0 0) diffraction plane of as-grown BaWO₄ single crystal was measured on the High-resolution X-ray diffractometer D5005, and the full-width at half-maximum value was found to be 26.64′′ The density and hardness of the BaWO₄ crystal was measured, the measured density was in agreement with the calculated result, and the Mohs hardness was about 4.     

Replacement of hydrides by TBAs and TBP for the growth of various III–V materials in production scale MOVPE reactors

Besides the standard group V precursors AsH₃ and PH₃, so-called alternative precursors like TBAs and TBP (tertiary-butyl-arsine and tertiary-butyl-phosphine) are more and more important in today's MOVPE processes. A lot of publications have demonstrated that these precursors can be successfully used for the growth of different III–V materials. In this study we want to demonstrate that TBAs and TBP can be used as the group V precursor in a complete family of production scale reactors. It is shown that these precursors can be used for the growth of InP-based as well as for GaAs-based materials. The reactors that have been employed are medium scale reactors (AIX 200/4; 1 × 2 inch, 3 or 4 inch or 3 × 2 inch capability) and large scale Planetary Reactors®, in particular the AIX 2400 system (15 × 2 inch or 5 × 4 inch). Materials that have been grown are (Al)GaInP on GaAs and GaInAsP on InP. The lower cracking energy of these precursors compared to PH₃ and AsH₃ allows one to use lower growth temperatures and lower V/III ratios, particularly in combination with the high cracking efficiencies of the used reactors. For the growth of GaInAsP on InP, the consumption of TBP and TBAs is up to 8 times lower than using PH₃ and AsH₃. GaInP on GaAs could be grown with a V/III ratio as low as 25 in a Planetary Reactor®. Good crystalline quality is demonstrated by DCXD (e.g. for GaInP: FWHM = 35 arcsec, substrate 32 arcsec). PL intensity and growth rate are not affected by using the alternative precursors. The compositional uniformity is similar to layers grown with arsine and phosphine (e.g. 1.5 nm uniformity for GaInAsP (λ = 1.5 μm) on 2 inch; approximately 1 nm uniformity for GaInP) [1,2]. The purity of the grown layers depends mainly on the quality of the TBP and TBAs. Using high purity TBP, InP revealed background carrier concentration in the mid 10¹⁴ cm⁻³ regime. Our investigation shows that TBP and TBAs can replace phosphine and arsine in state of the art MOVPE reactors. Both for single and multi-wafer production MOVPE reactors these compounds can be used successfully for the growth of the entire material spectrum in the Al---Ga---In---As---P system.     

Growth of cadmium mercury thiocyanate dimethylsulphoxide single crystal for laser frequency doubling

This paper reports the growth of an organometallic nonlinear optical (NLO) complex crystal, Cadmium mercury thiocyanate dimethyl-sulphoxide (CdHg(SCN)₄(H₆CP₂OS)₂, CMTD), which was grown from aqueous solution by a temperature lowering method. Its powder SHG intensity is higher than that of CMTC. The crystal size of CMTD can reach 25×23×15mm³. The solubility curve, and solubility variation with pH value are also reported. The growth habits of crystals of CMTD grown under different conditions are discussed and the optimized condition for the growth CMTD using a temperature-lowering method from aqueous solution are also discussed.     

Improved growth of PbI2 single crystals

The phase equilibrium and the crystallization process of lead iodide (PbI₂) melt have been primarily investigated according to the lead–iodine phase diagram. It is found that the iodine evaporation and the segregated lead deposition are the two important factors that affect the PbI₂ crystal quality. The new method of Pulling U-type quartz growth ampoule has been made to impede the decomposition of PbI₂ and the vaporization and condensation of iodine. An orange and translucent PbI₂ single crystal of large size was obtained by the improved growth method, i.e. U-type ampoule pulling. Resistivity of the as-grown crystal is up to 4×10¹¹ Ω cm, and IR transmission is up to 45% in the region from 7800 to 450 cm⁻¹. Therefore, the improved growth method is a promising convenient new method for the growth of high quality PbI₂ crystals.     

Quantum transport measurements on Si δ- and slab-doped In0.53Ga0.47As grown by molecular beam epitaxy

A series of high quality δ-doped In_0.53Ga_0.47As samples have been grown lattice matched to InP with design doping densities in the range 2×10¹² to 5×10¹² cm⁻². Analysis of the individual sub-band densities deduced from the Shubnikov-De Haas effect shows that both spreading and amphoteric behaviour increase with doping density.     

Growth and self-frequency doubling laser output of Nd : Ca4Gd0.275Y0.725O(BO3)3 crystal

In this letter, Nd : Ca₄Gd_0.275Y_0.725O(BO₃)₃ (Nd : GdYCOB) single crystal with good optical quality and large size has been grown by the Czochralski method. The absorption and fluorescence spectra have been measured. The self-frequency doubling (SFD) laser output of Nd : GdYCOB at 0.53 μm has been demonstrated when a Nd : GdYCOB crystal sample with dimensions of 3 mm×3 mm×7 mm (the phase-matched angle is θ=78.8°, Φ=90°) is pumped by a cw Ti : sapphire laser.     

Nanocrystallization of fresnoite glass. I. Nucleation and growth kinetics

We determined the internal nucleation, crystal growth and overall crystallization kinetics of fresnoite crystal (2BaO · TiO₂ · 2SiO₂) in an almost stoichiometric fresnoite glass. Due to the extremely high nucleation rates (10¹⁷ m⁻³ s⁻¹) that limit the maximum crystal size to 700 nm the nucleation densities and crystal sizes were estimated by scanning electron microscopy (SEM). The volume fraction crystallized was measured by X-ray diffraction. The nucleation rates obtained directly from SEM measurements reasonably agree with those calculated from the combination of overall crystallization with crystal growth kinetics. The activation enthalpies for viscous flow, transport of structural units across the nucleus/melt interface (nucleation) and crystal growth: ΔH_η, ΔH_τ and ΔH_U respectively, follow a similar trend to that observed for other stoichiometric silicate glasses that nucleate internally: ΔH_η=294>ΔH_τ=87>ΔH_U=61 kJ/mol. Fresnoite glass displays the highest internal nucleation rates so far measured in inorganic glasses. These rates are comparable to some metallic glasses and can lead to nanostructured glass-ceramics.     

Investigations on the effect of InSb and InAsSb step-graded buffer layers in InAs0.5Sb0.5 epilayers grown on GaAs (0 0 1)

We report the structural and electrical properties of InAsSb epilayers grown on GaAs (0 0 1) substrates with mid-alloy composition of 0.5. InSb buffer layer and InAs_xSb_1−x step-graded (SG) buffer layer have been used to relax lattice mismatch between the epilayer and substrate. A decrease in the full-width at half-maximum (FWHM) of the epilayer is observed with increasing the thickness of the InSb buffer layer. The surface morphology of the epilayer is found to change from 3D island growth to 2D growth and the electron mobility of the sample is increased from 5.2×10³ to 1.1×10⁴ cm²/V s by increasing the thickness of the SG layers. These results suggest that high crystalline quality and electron mobility of the InAs_0.5Sb_0.5 alloy can be achieved by the growth of thick SG InAsSb buffer layer accompanied with a thick InSb buffer layer. We have confirmed the improvement in the structural and electrical properties of the InAs_0.5Sb_0.5 epilayer by quantitative analysis of the epilayer having a 2.09 μm thick InSb buffer layer and 0.6 μm thickness of each SG layers.     

Top-seeded solution growth of LiB3O5

We report on the top-seeded solution growth of LiB₃O₅ from an excess B₂O₃ solution. Parameters investigated include the Li₂O/B₂O₃ ratio, rotation rate, pulling rate, cooling rate, and seed direction. With careful control of the above parameters, we have grown clear crystals of 25 × 30 × 20 mm in size. Selected nonlinear optical properties of these crystals are reported. Observations concerning the occurrence of unstable growth (inclusions, hopper growth) are discussed, and methods to eliminate the unstable growth are suggested.     

Surface features of synthetic silicate garnets

Crystals of Ca₃Al₂Si₃O₁₂-Mg₃Al₂Si₃O₁₂ solid solution have been synthesized with excess water at various high temperature-high pressure conditions. Surface features observed on the faces of the synthetic garnets and the habit variations caused by changes in Ca/Mg concentration of bulk compositions are described. The garnet crystal product are bounded predominantly by {110} faces and occasionally by small {211} and {321} faces when grown from Ca-rich bulk compositions.     

Growth of large crystals of deuterated tetrathiafulvalene tetracyanoquinodimethan (TTF-TCNQ-d8)

Large single crystal platelets of TTF-TCNO-d₈ up to 30 × 6 × 0.7 mm³ were grown from acetonitrile by the diffusion method at 36°C.     

RHEED studies of MOMBE growth using TMGa or TEGa with As2

MOMBE and CBE growth has until recently been based on largely empirical studies of the epitaxial process. We have used reflection high energy electron diffraction (RHEED), previously applied to the study of MBE, to study the growth GaAs using TMGa and As₂. In this work we have extended our previous studies to include a detailed study of the effect of As₂ flux on growth rate and to compare data on singular and vicinal plane surfaces cut off orientation in two orthogonal {110} directions. Clear evidence for site blocking mechanisms is observed together with an indication that the concentration of elemental Ga present on the surface during growth is negligible even under conditions where the arrival rate of TMGa exceeds that As₂. We have compared this behaviour with that observed using TEGa and As₂ under identical conditions. Using TEGa a conversion from a (2×4) to (4×2) reconstructed surface is observed under As deficient conditions indicating the presence of elemental Ga on the surface. This is accompanied by an abrupt change in growth rate similar to that secn in MBE.     

Heavily carbon-doped p-type (In)GaAs grown by gas-source molecular beam epitaxy using diiodomethane

Heavily carbon-doped p-type In_xGa_1−xAs (0≤x<0.49) was successfully grown by gas-source molecular beam epitaxy using diiodomethane (CH₂I₂), triethylindium (TEIn), triethylgallium (TEGa) and AsH₃. Hole concentrations as high as 2.1×10²⁰ cm⁻³ were achieved in GaAs at an electrical activation efficiency of 100%. For In_xGa_1−xAs, both the hole and the atomic carbon concentrations gradually decreased as the InAs mole fraction, x, increased from 0.41 to 0.49. Hole concentrations of 5.1×10¹⁸ and 1.5×10¹⁹ cm⁻³ for x = 0.49 and x = 0.41, respectively, were obtained by a preliminary experiment. After post-growth annealing (500°C, 5 min under As₄ pressure), the hole concentration increased to 6.2×10¹⁸ cm⁻³ for x = 0.49, probably due to the activation of hydrogen-passivated carbon accepters.     

Observation of optical inhomogeneities in flux grown KTP crystals

Optical inhomogeneities in potassium titanyl phosphate crystals grown from different fluxes have been investigated. In the crystals grown from a flux which contains tungsten, striations parallel to the {011} faces were observed. The main reason for forming striations is the change in tungsten concentration with change in growth rate. In the case of a potassium phosphate flux, no striations were observed in the crystal which was grown at almost the same temperature and stirring conditions as for the tungstate flux. We can conclude that the phosphate flux is more suitable for the growth of optically good crystals for KTP as laser harmonic converters.