以聚酰胺-胺树形分子为模板制备AgI纳米簇

本文以聚酰胺-胺(PAMAM)树形分子为模板,原位制备AgI纳米簇.系统地研究了AgI纳米簇制备过程中各种反应条件如树形分子端基、反应时间、Ag⁺与PAMAM摩尔比等对AgI纳米簇粒径的影响,分别用紫外-可见光谱、荧光光谱、透射电镜等对所制备的纳米簇进行表征.在相同的条件下,以G4.5-COOH₃为模板较以G5.0-NH₂为模板制备的AgI纳米簇粒径小、分布均匀,这主要取决于G4.5-COOCH₃PAMAM树形分子所起的“内模板”作用.G4.5-COOH₃树形分子浓度为1×10^-5mol/L,Ag⁺与树形分子摩尔比为30:1时所制备的AgI纳米簇的粒径分布均匀、稳定性好,室温避光可稳定存在两个月以上.     

AgBr纳米簇：PAMAM树形分子模板法制备及光催化性能研究

以酯端基聚酰胺-胺(PAMAM)树形分子为模板，原位制备了AgBr纳米簇。由于酯端基的半代PAMAM树形分子起到“内模板”作用，制得的AgBr纳米簇粒径小、尺寸分布窄、稳定性好，并通过改变Ag⁺∶PAMAM树形分子的物质的量的比可以精确控制纳米簇的尺寸。AgBr纳米簇/树形分子纳米复合材料在光催化降解甲基橙方面具有很好的催化能力，且随纳米簇的尺寸减小，其催化能力增强。     

以PAMAM树形分子为模板制备Pd纳米簇合物

以酯端基聚酰胺-胺树形分子(PAMAM)为模板在甲醇溶剂中制备了Pd纳米簇合物. 采用紫外-可见分光光度法和红外光谱法研究了Pd²⁺与树形分子的作用机理, 结果表明, Pd²⁺与树形分子内部胺基基团(主要为叔胺基)产生了络合作用. 采用硼氢化钠还原法制备了树形分子包裹的、粒径为2 nm的球形面心立方Pd纳米簇合物. 紫外-可见吸收光谱研究结果表明, Pd²⁺与树形分子的摩尔比越小, 生成的纳米簇合物尺寸越小; 由于高代数树形分子具有封闭结构, 且其内部配体数目较多, 采用较高代数的树形分子(5.5代)比低代数(3.5代)更有利于得到尺寸小、分散性较好的Pd纳米簇合物.     

PAMAM树形分子与Cd2＋的配位作用研究及CdS/PAMAM纳米复合材料的制备与表征

CdS半导体纳米簇具有独特的光、电性能, 如何制备均匀分散的、能够稳定存在的CdS纳米簇是目前的研究热点之一. 以聚酰胺-胺(PAMAM)树形分子为模板, 原位合成了CdS纳米簇. 首先用UV-Vis分光光度法研究了与树形分子的配位机理, 得出G4.5和G5.0的平均饱和配位数分别为16和34, 并发现在G4.5PAMAM树形分子中Cd^2＋主要与最外层叔胺基配位, 在G5.0PAMAM树形分子中Cd^2＋主要与最外层伯胺基配位. 酯端基的G4.5的模板作用要明显优于胺端基的G5.0. 通过改变Cd^2＋与G4.5树形分子的摩尔比可以得到不同粒径的CdS纳米簇. 溶液的pH值对CdS纳米簇影响很大, pH在7.0左右制备的CdS纳米簇粒径小而均匀, 且溶液稳定性高. 用UV-Vis分光光度计和TEM对CdS纳米簇的大小和形貌进行了表征. 结果表明TEM观测CdS纳米簇的粒径要大于用Brus公式的估算值.     

PAMAM树形分子与Cd2＋的配位作用研究及CdS/PAMAM纳米复合材料的制备与表征

CdS半导体纳米簇具有独特的光、电性能, 如何制备均匀分散的、能够稳定存在的CdS纳米簇是目前的研究热点之一. 以聚酰胺-胺(PAMAM)树形分子为模板, 原位合成了CdS纳米簇. 首先用UV-Vis分光光度法研究了与树形分子的配位机理, 得出G4.5和G5.0的平均饱和配位数分别为16和34, 并发现在G4.5PAMAM树形分子中Cd^2＋主要与最外层叔胺基配位, 在G5.0PAMAM树形分子中Cd^2＋主要与最外层伯胺基配位. 酯端基的G4.5的模板作用要明显优于胺端基的G5.0. 通过改变Cd^2＋与G4.5树形分子的摩尔比可以得到不同粒径的CdS纳米簇. 溶液的pH值对CdS纳米簇影响很大, pH在7.0左右制备的CdS纳米簇粒径小而均匀, 且溶液稳定性高. 用UV-Vis分光光度计和TEM对CdS纳米簇的大小和形貌进行了表征. 结果表明TEM观测CdS纳米簇的粒径要大于用Brus公式的估算值.     

高分子模板对CdS量子点制备及其光催化性能的影响

分别以球形聚酰胺-胺(PAMAM)树形分子和线形聚乙烯吡咯烷酮(PVP)两种结构不同的高分子为模板, 原位制备了分散良好的CdS量子点(CdS QDs), 并以甲基橙为降解对象, 研究了高分子模板结构对CdS量子点的制备和光催化性能的影响. 结果表明, 以PAMAM 树形分子为模板制备的CdS量子点(CdS QDs/PAMAM)比以PVP为模板制备的CdS量子点(CdS QDs/PVP)的尺寸分布更窄, 激子吸收峰更明显, 光致发光(PL)强度更高|并且在量子点尺寸接近的情况下, CdS QDs/PAMAM的催化效率明显高于CdS QDs/PVP. 这是由于PAMAM树形分子独特的结构有利于生成尺寸均匀的CdS量子点, 且不易钝化量子点表面的活性位点|而线性的PVP分子量分布较宽, 使制备的量子点的尺寸分布较宽, 且PVP分子链缠绕在CdS量子点表面, 钝化了部分活性位点, 降低催化效率. 此外, CdS QDs/PAMAM的催化能力随粒径减小而增大.     

聚酰胺-胺型树形分子模板法制备Pt纳米簇

利用紫外-可见吸收光谱和红外光谱对Pt2＋与G5.5-COOCH3聚酰胺-胺型树形分子的络合机理进行了研究, 结果表明Pt2＋与G5.5-COOCH3 PAMAM的最外层叔胺基发生络合作用, 但两者之间达到络合平衡需要较长时间, 且平衡时间随Pt2＋与树形分子物质的量比增大而增长; Pt2＋与G5.5-COOCH3树形分子的最大络合数为50～55; 采用硼氢化钠还原法原位制备了G5.5-COOCH3 PAMAM包裹、平均粒径小于2 nm、多晶的球形Pt纳米簇, 并研究了Pt2＋与PAMAM物质的量比对Pt纳米簇形貌的影响, 实验结果表明, Pt2＋与PAMAM物质的量比为10时, 生成尺寸较小分布较窄的内型Pt纳米簇/树形分子复合材料, 而物质的量比为50时, 会生成部分尺寸较大、分布较宽的外型Pt纳米簇/树形分子纳米复合材料.     

温度对聚酰胺-胺树形分子模板法制备CdS量子点的影响

为了研究温度对聚酰胺-胺(PAMAM)树形分子的模板法制备硫化镉(CdS)量子点的影响, 以4.5代(G4.5, 64个甲酯端基)PAMAM树形分子为模板, 在－10～30 ℃的温度范围内制备了分散良好的CdS量子点. 用透射电子显微镜(TEM)表征了CdS量子点的形貌、尺寸; 用紫外-可见光谱(UV-Vis)和光致发光光谱(PL)表征了CdS量子点的光学性能. 发现在相同条件下, 制备温度从－10 ℃升高到30 ℃, CdS量子点粒径从1.8 nm增大到3.4 nm, 其中在10 ℃时制备的量子点的尺寸分布最窄; CdS量子点的吸收和发射光谱均随温度增大而红移, 其中10 ℃时制备的量子点的室温光致发光效率最高. 这表明制备温度决定了树形分子的配位基团与Cd^2＋的分离速度, 并影响了CdS量子点的成核和生长过程, 从而最终决定了CdS量子点的尺寸及尺寸分布、光致发光颜色和发光效率.     

低代端酯基PAMAM树形分子存在下银纳米颗粒的制备

在低代端酯基PAMAM树形分子(G1.5-COOCH₃)存在时，用氢气还原AgNO₃制备出银纳米颗粒。用透射电子显微镜(TEM)，电子衍射(ED)，紫外-可见吸收光谱(UV-Vis)和红外光谱(FT-IR)对所制备的银纳米颗粒进行了表征。实验结果表明，当用氢气作为还原剂时，以低代树形分子为保护剂，通过优化还原条件，可成功制备尺寸稳定、均一的银纳米颗粒，其粒径为2.9±0.5 nm，且所制备的银纳米颗粒的粒径分布较窄。根据树形分子的理论尺寸与制备的银纳米颗粒的粒径关系，可推断出大多数的银纳米颗粒是由多个树形分子所包围而稳定存在。     

以树形分子为模板制备银纳米颗粒

以硝酸银为原料,硼氢化钠为还原剂,PAMAM树形分子为模板兼稳定剂,制备出粒径分布范围在4～7mm的银纳米颗粒．实验发现,其他条件相同时,银纳米颗粒的粒径随着Ag^ ／树形分子摩尔比的增加而增加,并且树形分子代数越高,所起的模板作用越显著．还研究了溶液pH值的影响,发现当溶液pH值在7左右时,可以制得粒径较小、分散性较好的银纳米颗粒．用紫外-可见光谱,透射电镜(TEM)以及原子力显微镜(AFM)等测试手段对所制得的银纳米颗粒进行了表征．     

PVP and G1.5 PAMAM dendrimer co-mediated synthesis of silver nanoparticles

PVP and G1.5 PAMAM dendrimer co-mediated silver nanoparticles of smaller than 5 nm in diameter were prepared using H₂ as reducing agent. With the TEM micrograph, it was found that the molar ratios of PVP and G1.5 PAMAM dendrimer have significant effect in the morphology and size distribution of silver nanoparticles. The reaction rate (fitting a first-order equation) was strongly influenced by the molar ratios of PVP and G1.5 PAMAM dendrimer and the reaction temperature. From the UV-Vis spectra of an aqueous solution of silver nanoparticles, they could be stored for at least 2 months without coagulation at room temperature.     

PAMAM树形分子为模板低温制备纳米硫化锌空心球

Hollow ZnS spheres have been prepared in the presence of generation 3.5 poly (amidoamine) dendrimers with surface ester groups (G3.5-COOCH3 PAMAM dendrimer) as synthetic matrix template. The products obtained were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and UV-Vis absorption. TEM studies show that the hollow spheres with diameters ranging from 80 to 100 nm are prepared. The range of wall thickness was estimated to be about 20～30 nm. It was found that the concentration of PAMAM dendrimer had a significant influence on the formation of hollow ZnS spheres. The possible formation mechanism of the hollow spherical structure is also discussed.     

Comparison of PAMAM-Au and PPI-Au nanocomposites and their catalytic activity for reduction of 4-nitrophenol

Dendrimer-Au nanocomposites are prepared in aqueous solutions using poly(amidoammine)dendrimers (PAMAM) (generation 2, 3, and 5) and poly(propyleneimine)dendrimers (PPI)(generation 2, 3, and 4) by wet chemical NaBH(4) method. The Au nanoparticles thus obtained are 2-4 nm in diameter for both dendrimers and no generation dependence on the particle size is observed, whereas the generations of the dendrimers are increased as stabilization of Au-nanoparticles is achieved with lower dendrimer concentrations. Studies of the reduction reaction of 4-nitrophenol using these nanocomposites show that the rate constants for the PAMAM dendrimers (generations 2 and 3) are higher than those for the PPI dendrimers (generations 2 and 3), while a distinct difference in the rate constants is not seen for the PAMAM dendrimer (generation 5) or the PPI dendrimer (generation 4). In addition, the rate constants for the reduction of 4-nitrophenol involving all the dendrimers decrease with increases in dendrimer concentrations.     

Strong blue photoluminescence and ECL from OH-terminated PAMAM dendrimers in the absence of gold nanoparticles

A product showing strong blue photoluminescence was obtained by oxidation of OH-terminated PAMAM dendrimers, such as G4-OH, G2-OH, and G0-OH, with HAuCl4 or (NH4)2S2O8. The fluorescence emission spectrum peaked at 450 nm, while the excitation maximum was at 380 nm, independent of the generation of dendrimer. The product also shows two weak electrogenerated chemiluminescence (ECL) signals upon cycling the potential between about 1.2 and -1.7 V.     

Interaction forces between poly(amidoamine) (PAMAM) dendrimers adsorbed on gold surfaces

Interaction forces between two gold surfaces with adsorbed poly(amidoamine) (PAMAM) dendrimers (generations G3.0 and G5.0) have been investigated using colloidal probe atomic force microscopy (AFM). In the absence of dendrimers or at their low concentrations, an attractive force derived from the van der Waals interaction was observed. On the other hand, this attractive interaction changed to repulsion with increasing dendrimer concentration. The origin of the repulsion can be attributed to either an electric double layer interaction or a steric effect of the adsorbed dendrimers, depending on the concentration of dendrimer. The steric hindrance was also influenced by the generation of the dendrimer; the force-detectable distance in the presence of PAMAM G5.0 dendrimer was slightly longer than that in the presence of G3.0 dendrimer. In order to estimate the occupied area of each dendrimer adsorbed on gold, quartz crystal microbalance (QCM) measurement was also carried out.     

Preparation of PAMAM- and PPI-metal (silver, platinum, and palladium) nanocomposites and their catalytic activities for reduction of 4-nitrophenol

Dendrimer-metal (silver, platinum, and palladium) nanocomposites are prepared in aqueous solutions containing poly(amidoamine) (PAMAM) dendrimers with surface amino groups (generations 3, 4, and 5) or poly(propyleneimine) (PPI) dendrimers with surface amino groups (generations 2, 3, and 4). The particle sizes of the metal nanoparticles obtained are almost independent of the generation as well as the concentration of the dendrimer for both the PAMAM and the PPI dendrimers; the average sizes of silver, platinum, and palladium nanoparticles are 5.6-7.5, 1.2-1.6, and 1.6-2.0 nm, respectively. It is suggested that the dendrimer-metal nanocomposites are formed by adsorbing the dendrimers on the metal nanoparticles. Studies of the reduction reaction of 4-nitrophenol by these nanocomposites show that the rate constants are very similar between PAMAM and PPI dendrimer-silver nanocomposites, whereas the rate constants for the PPI dendrimer-platinum and -palladium nanocomposites are greater than those for the corresponding PAMAM dendrimer nanocomposites. In addition, it is found that the rate constants for the reduction of 4-nitrophenol involving all the dendrimer-metal nanocomposites decrease with an increase in the dendrimer concentrations, and the catalytic activity of dendrimer-palladium nanocomposites is highest.     

磁性Fe_3O_4@PS@PAMAM-Ag复合催化粒子的制备及其可再生催化性能(英文)

采用聚苯乙烯(PS)包裹Fe3O4磁性纳米粒子,制得Fe3O4@PS复合微球,以此作为磁性载体,通过微球表面的羧基将聚酰胺-胺类树形大分子(PAMAM)连接到磁性载体上,然后使Ag纳米粒子镶嵌在树形分子层中,制得可再生的金属复合催化粒子Fe3O4@PS@PAMAM-Ag.并采用红外光谱、扫描电镜、电感耦合等离子体质谱(ICP-MS)和X射线光电子能谱等方法对复合催化粒子进行了表征,结果表明,树形分子可以较好地分散和稳定金属Ag纳米粒子,所制复合催化粒子表面Ag含量为1.64%,具有较高的催化还原对硝基苯酚的活性.同时,利用外加磁场可以方便快捷地从反应体系中分离出来,继续用于下一次反应中,复合催化粒子循环使用6次后,仍保持完全的催化性能.