Electrochemical synthesis and characterization of poly(pyrrole-co-tetrahydrofuran) conducting copolymer

The direct electrochemical copolymerization of pyrrole and tetrahydrofuran in various monomer ratios was carried out by potentiostatic methods in nitromethane solution. The copolymer has been characterized using FT-IR, scanning electron microscopy (SEM), differential scanning calorimetry (DSC), thermal gravimetrical analysis (TGA), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and elemental analysis. The results showed that the electrochemical oxidation of pyrrole and tetrahydrofuran comonomers generated true copolymers rather than blends of the two homopolymers. The copolymer showed a better flexibility than pure polypyrrole. The electrical conductivity of the copolymers increases with the amount of polypyrrole in the copolymer between the value of 1.69 S/cm and 0.71 S/cm.     

电化学合成吡咯与己内酰胺导电共聚物

采用恒电位方法实现了吡咯与己内酰胺在导电玻璃电极上的直接电化学共聚,聚合反应在含有0.1mol/L吡咯和1.5 mol/L己内酰胺的硝基甲烷电解质溶液中进行,外加电位控制在1.2 V以上.聚合产物中聚吡咯与聚己内酰胺链段的组成可通过调节合成电位加以控制.共聚物的形貌、结构与性质采用扫描电子显微镜、热重分析、红外光谱等手...     

Preparation and characterization of conducting poly(acryloyl chloride)‐g‐ polypyrrole copolymer

The electroactive copolymer of poly(acryloyl chloride) (PAC) and polypyrrole (PPy) can be synthesized by electrochemical polymerization using a polymer precursor which contains a pyrrole moiety in its side chain. Poly(acryloyl pyrrole) (PAP) was synthesized chemically with acryloyl chloride and potassium pyrrole salt and characterized using FT‐IR and ¹H‐NMR spectroscopy. PAP dissolved in dimethyl formamide (DMF), was spin‐coated on a platinum electrode and polymerized electrochemically in the electrolytic mixture solution consisting of acetonitrile, 0.1 M pyrrole, and 0.1 M lithium perchlorate. Constant potential electrolysis showed that pyrrole groups in the precursor were oxidized to form PPy, that is, they acted as grafting centers at which the PPy grew. Scanning electron microscopy (SEM) results and conductivity measurements supported the formation of the graft copolymer. The morphological feature of PAC‐g‐PPy copolymer films showed homogeneous structure, but that of PAC/PPy composite films showed irregular structure. The maximum conductivity of the final products was about 1 S/cm. Copyright © 2002 John Wiley & Sons, Ltd.     

Preparation and electrochemistry of modified polypyrrole films by anodic copolymerization techniques

The anodic copolymerization of pyrrole and N-(ω-ferrocenylalkyl)pyrroles, FcPy-n, at platinum electrodes in an electrolyte consisting of tributylammonium benzenesulfonate in moist acetonitrile is optimized with respect to the absolute and relative concentrations of the monomers and the spacer length of FcPy-n. The copolymer composition is estimated from cyclic voltammograms of the polymer films. Only films with less than 20% FcPy-n content show the typical polypyrrole voltammograms. Free standing copolymer films with a conductivity of ca. 10 S cm⁻¹ can be prepared.     

氧化石墨烯/聚吡咯插层复合材料的制备和电化学电容性能

以FeCl₃-甲基橙(MO)为模板, 通过化学原位聚合法成功制备出氧化石墨烯/聚吡咯(GO/PPy)插层复合材料. 采用X射线衍射(XRD)、傅里叶变换红外(FTIR)光谱、扫描电镜(SEM)和透射电镜(TEM)等测试技术对复合材料进行物性表征. 此外, 利用循环伏安、恒电流充放电和交流阻抗测试方法对复合材料在两种不同水系电解液(1 mol·L^-1 Na₂SO₄和1 mol·L^-1 H₂SO₄)中的电化学性能进行了研究. 结果显示: 氧化石墨烯和聚吡咯表现出各自优势并发挥协同作用, 使得GO/PPy插层复合材料在中性和酸性电解液中都显示出可观的比电容. 电流密度为0.5 A·g^-1时, GO/PPy 插层复合材料在Na₂SO₄和H₂SO₄电解液中的比电容分别为449.1 和619.0 F·g^-1, 明显高于纯PPy的比电容. 经过800 次循环稳定性测试后, 两种不同电解液中, 复合材料初始容量的保持率分别为92%和62%. 其中酸性电解液体系中初始容量更大, 而中性溶液中具有更稳定的循环性能.     

Investigation of SPR and electrochemical detection of antigen with polypyrrole functionalized by biotinylated single-chain antibody: A review

An electrochemical label-free immunosensor based on a biotinylated single-chain variable fragment (Sc-Fv) antibody immobilized on copolypyrrole film is described. An efficient immunosensor device formed by immobilization of a biotinylated single-chain antibody on an electropolymerized copolymer film of polypyrrole using biotin/streptavidin system has been demonstrated for the first time. The response of the biosensor toward antigen detection was monitored by surface plasmon resonance (SPR) and electrochemical analysis of the polypyrrole response by differential pulse voltammetry (DPV). The composition of the copolymer formed from a mixture of pyrrole (py) as spacer and a pyrrole bearing a N-hydroxyphthalimidyl ester group on its 3-position (pyNHP), acting as agent linker for biomolecule immobilization, was optimized for an efficient immunosensor device. The ratio of py:pyNHP for copolymer formation was studied with respect to the antibody immobilization and antigen detection. SPR was employed to monitor in real time the electropolymerization process as well as the step-by-step construction of the biosensor. FT-IR demonstrates the chemical copolymer composition and the efficiency of the covalent attachment of biomolecules. The film morphology was analyzed by electron scanning microscopy (SEM).Results show that a well organized layer is obtained after Sc-Fv antibody immobilization thanks to the copolymer composition defined with optimized pyrrole and functionalized pyrrole leading to high and intense redox signal of the polypyrrole layer obtained by the DPV method. Detection of specific antigen was demonstrated by both SPR and DPV, and a low concentration of 1 pg mL⁻¹ was detected by measuring the variation of the redox signal of polypyrrole.     

Efficient Hybrid Photovoltaic Devices Based on in-situ Electrochemical Copolymerization of 3-Methylthiophene and Bithiophene into Pores of Nanocrystalline TiO2

Novel organic and inorganic hybrid photovoltaic devices were thbricated by in-situ electrochemical copolymerization of 3-methylthiophene（3MT） and bithiophene（BT） into the pores of nanostructured TiO2 sintered on fluorine-doped tin oxide（FTO） substrate. The photoactive layer was investigated by Fourier transform infrared（FTIR） spectroscopy, ultraviolet-visable（UV-Vis） spectrometer, scanning electron microscope（SEM） and cyclic voltammo- gram characterization. Device efficiency based on different molar feed ratios of 3MT and BT during electrochemical polymerization, and the effect of in-situ copolymer state（doped by electrolyte and de-doped） were measured and compared. Under the solar illumination of 100 mW/cm2（AM 1.5）, an optimized device efficiency of 0.938% was obtained when the molar ratio of 3MT to BT was 500：1, polymerization time was 500 s and the system was in doped copolymer state, respectively. The mechanism of overall photovoltaic parameter improvement was discussed.     

Characterization and Potential Applications of Immobilized Glucose Oxidase and Polyphenol Oxidase

Pyrrole functionalized polystyrene (PStPy) was copolymerized with pyrrole to obtain a conducting copolymer, P(PStPy‐co‐Py) which is used as the immobilization matrix. Glucose oxidase and polyphenol oxidase enzymes were immobilized via the entrapment method by electrochemical polymerization. Enzyme electrodes were prepared by electrolysis at a constant potential using sodium dodecyl sulfate (SDS) as the supporting electrolyte during the copolymerization of PStPy with pyrrole. Maximum reaction rates (V_max) and enzyme affinities (Michaelis‐Menten constants, K_m) were determined for the enzyme entrapped both in polypyrrole (PPy) and P(PStPy‐co‐Py) matrices. Optimizations of enzyme electrodes were done by examining the effects of temperature and pH on enzymes' activities along with the shelf life and operational stability investigations. Glucose oxidase enzyme electrodes were used for human serum analysis and glucose determination in two brands of orange juices. Polyphenol oxidase enzyme electrodes were used for the determination of phenolics in red wines of Turkey.     

Electrochemical measurements of the ion conductivity, permselectivity and transference numbers of polypyrrole and polypyrrole derivatives

Electrochemical dc and ac measurements were carried out on free-standing polypyrrole (ppy) membranes to study the ion conductivity and permselectivity of the polymer as a function of the oxidation state. The membranes were prepared by electropolymerisation and mounted in a two-compartment cell, where the oxidation state of the ppy membrane could be adjusted by potentiostatic polarisation and the ion conductivity and permselectivity of the polymer could be measured in a symmetrical electrolyte/membrane/electrolyte configuration. Combining constant current permeation experiments with solution analysis using ion chromatography (IC) and atomic absorption spectroscopy (AAS), it was demonstrated that ppy exhibits not only an appreciable ion conductivity but also a distinct permeability and selectivity for anions in the oxidised state. Incorporation of immobile anions like dodecylsulfate or copolymerization with a modified pyrrole monomer like N-sulfopropyl-pyrrole carrying a sulfonate group leads to modified membranes which exhibit distinct cation permselectivity in the reduced state. Such a membrane can be switched dynamically between anion and cation permeability through electrochemical oxidation and reduction of the polymer backbone. Received: 27 March 1997 / Accepted: 18 July 1997     

Characterization of Conducting Copolymer of Pyrrole via Pyrolysis Mass Spectrometry

In this work, structural and thermal characterization of BF₄ ^? doped copolymer of pyrrole (PPy) with 2‐methylbutyl‐2‐(3‐thienyl)acetate prepared by electrochemical polymerization were performed via a pyrolysis mass spectrometry technique. The pyrolysis mass spectrometry data of the copolymer PPy/PMBTA, and the homopolymers; polypyrrole, PPy, and poly(2‐methylbutyl‐2‐(3‐thienyl)acetate), PMBTA were analyzed and compared. It has been determined that when the electrochemical polymerization of pyrrole was achieved on a PMBTA coated anode through the thiophene moieties of PMBTA, thermal stability of PMBTA chains increased slightly and the decomposition of both units followed quite similar pathways indicating an increase in the thermal stability of PMBTA chains unlike what was observed for PTSA doped PPy/PMBTA copolymer.     

Electrocatalytic hydrogenation of 4-chlorophenol on the glassy carbon electrode modified by composite polypyrrole/palladium film

A polypyrrole/palladium composite film was prepared on a glassy carbon electrode by the electrochemical deposition method. The palladium particles were uniformly dispersed on a polypyrrole film that was previously electrodeposited on a glassy carbon electrode. By controlling the polymerization process of pyrrole, a highly porous polypyrrole film was obtained; this kind of structure provided more surface areas for depositing palladium particles. The sizes of Pd particles deposited on the porous polypyrrole film are about 15-30 nm. The X-ray photoelectron spectroscopy results showed there was strong interaction between polypyrrole film and palladium particles. This modified electrode showed excellent current efficiency (49.5%) for electrochemical hydrogenation of 4-chlorophenol and the phenol was the sole product. The potential effect on the dechlorination process was also investigated.     

基于静电吸附作用制备PPy/CNTs复合材料

通过添加十二烷基苯磺酸钠(SDBS), 在碳纳米管(CNTs)表面引入具有静电吸附作用的基团, 使吡咯单体附着于CNTs表面, 然后发生化学原位聚合, 得到了由片状聚吡咯(PPy)包覆CNTs所构成的PPy/CNTs复合材料, 开辟了一条易于工业化生产制备PPy/CNTs复合材料的途径. 所得材料和CNTs借助傅立叶变换红外光谱、扫描电子显微镜、透射电子显微镜等设备进行了成分和形貌的表征; 并将所得材料组装成电化学超级电容器, 进行了电化学性能测试. 研究结果表明, 加入SDBS后, 吡咯单体能很好地吸附于CNTs表面; CNTs的应用细化了PPy的颗粒, 改善了PPy的导电性能和机械性能, 使PPy/CNTs复合材料呈现出多孔状; 其电化学容量达到101.1 F·g-1(有机电解液), 是同样制备条件下所得纯PPy电化学容量(19.0 F·g-1)的5倍多, 约是所用纯CNTs电化学容量(25.0 F·g-1)的4倍.     

Immobilization of glucose oxidase on the films prepared by electrochemical copolymerization of pyrrole and 1-(2-carboxyethyl)pyrrole for glucose sensing

Glucose oxidase (GOx) was immobilized through amide linkages on the surfaces of the conducting polymer films prepared by electrochemical copolymerization of pyrrole (Py) and 1-(2-carboxyethyl)pyrrole (Py-COOH) for the purpose of fabricating GOx-immobilized electrodes for amperometric sensing of glucose. The conductivity of the copolymer film was in the range 10⁻⁸-10⁻³ S/cm and showed a tendency to decrease with increasing content of Py-COOH units in the copolymer. The amount of immobilized GOx increased significantly with increasing content of Py-COOH units in the copolymer film up to 30%, and showed a tendency to level off when the content of Py-COOH units became larger. The activity of immobilized GOx per area of the copolymer film decreased slightly with increasing content of Py-COOH units in the copolymer. Although the GOx-immobilized copolymer films gave the amperometric response to glucose depending on its concentration, the magnitude of the response to a given concentration was found to decrease with increasing content of Py-COOH units in the copolymer. The variation in the amperometric response was attributed to the difference in conductivity of the copolymer film. The appropriate content of Py-COOH units in the copolymer was considered to be 5% or less for the amperometric sensing of glucose with the GOx-immobilized copolymer film.     

Electrochemical fabrication of novel fluorescent polymeric film: Poly(pyrrole–pyrene)

We describe herein the electrochemical characterization and polymerization of 4-pyren-1-yl-butyric acid 11-pyrrol-1-yl-decyl ester (pyrrole–pyrene) in CH₃CN. The electrochemical oxidation of the pyrrole group at 0.77 V vs Ag/Ag + 10 mM in CH₃CN led to the first example of a fluorescent polypyrrole film. The mechanism of deposition on platinum electrode was studied by voltammetry and chronoamperometry. The optical properties of the polymeric films electrogenerated on ITO electrodes were examined by UV–visible spectroscopy and fluorescence microscopy indicating an increase in fluorescence properties by increased polymer thickness. The electrochemical oxidation of pyrenyl group linked to the polypyrrole backbone was carried out at 1.2 V. This additional polymerization was demonstrated by UV–visible spectroscopy and induced the loss of the fluorescence properties of the resulting polymeric film.     

Molecular Dynamics Simulations of the Orientation and Reorientational Dynamics of Water and Polypyrrole Rings as a Function of the Oxidation State of the Polymer

Summary: Polypyrrole is one of the most widely‐studied conducting polymers due to its steady electrochemical response and good chemical stability in different solvents, including organic and inorganic ones. In this work, we provide for the first time valuable information in atomic detail concerning the steady and dynamic properties of pyrrole rings as a function of the oxidation state of the polymer. The study was carried out by Classical molecular dynamics simulation, where the system was modelled by 256 polypyrrole chains of 10 pyrrole rings each. Water was explicitly introduced in our simulations. Besides the uncharged or reduced state, two steady oxidation states of the polymer have been simulated by introducing a net charge (+1) on 85 and 256 of the polypyrrole chains. To balance the charges emerging in these oxidised states, 85 and 256 chloride ions (Cl⁻¹) respectively, were introduced into the system. From an analysis of the simulated trajectories, the orientation and relaxation times of water and pyrrole rings were evaluated for the different oxidation states of the polymer across the polypyrrole/water interface. The calculated densities for different oxidation states describe the swelling or shrinking process during electrochemical oxidation or reduction respectively. The rotational relaxation times calculated for the polypyrrole rings decrease with increasing oxidation of the polymer, which is in a good agreement with experimental electrochemical data. Almost no variation in pyrrole ring orientation was measured for the different oxidation states of the polymer, even compared with polypyrrole bulk. As regards the water structure in the vicinity of the polypyrrole/water interface, both the orientation and orientation relaxation time were strongly affected by the presence of charges in the polymer. Thus, the water dipole was strongly orientated in the vicinity of the water/polypyrrole interface and its orientational relaxation time increased by one order of magnitude compared with bulk water, even when only one‐third of the total polymer chains were oxidised. The results attained in this work were validated with experimental results, when they were available.

Polypyrrole ring orientation and water orientation at the polypyrrole/water interface. (a) 256 rPPy and (b)171 rPPy + 85 oPPy.     

Electrocatalytic Oxidation of Amines on a Mediator‐Modified Electrode by Electrochemical Copolymerization of Nitroxyl Radical Precursor Containing Pyrrole Side Chain and Bithiophene

This paper describes the electrocatalytic oxidation of amines on TEMPO (2,2,6,6‐tetramethylpiperidine‐1‐oxyl)‐modified electrodes prepared by electrochemical copolymerization of TEMPO precursor containing pyrrole side chain and 2,2′‐bithiophene. The modified electrode exhibits electrocatalytic activity for the oxidation of primary and secondary amines. Cyclic voltammetric studies showed that the peak current of the cyclic voltammogram increased linearly with increasing concentration of amine in the sample solution.     

以聚吡咯和纳米金为基质基于电化学交流阻抗测试的乙肝表面抗原免疫传感器研究

A novel simple immunosensing strategy for fabrication of hepatitis B surface antigen detection has been developed via electrochemical impedance spectroscopy （EIS） as a platform. At first, the conductive polymer polypyrrole （PPy） film was electrodeposited on a platinum electrode surface to adsorb the gold nanoparticles （nano-Au） via the opposite-charged adsorption technique, and then hepatitis B surface antibodies were adsorbed onto the surface of nano-Au. The modification procedure was characterized by EIS. Such spectroscopy is attributed to the concomitant conductivity changes of the polymerized pyrrole film and gold nanoparticles. The factors influencing the performance of resulting immunoelectrode were studied in detail. The linear range of the resulting immunoelectrode is from 2.6 to 153.6 ng.mL^-1 with a detection limit of 1.3 ng·mL^-1 at 3σ. In addition, the experiment results indicate that antibody immobilized on this way exhibits a good sensitivity, selectivity, high stability and a long-term maintenance of bioactivity, implying a great promising alternative approach for reagentless immunosensing analysis in the clinical diagnosis.     

Cross-linking copolymers of acrylates’ gel electrolytes with high conductivity for lithium-ion batteries

The cross-linking gel copolymer electrolytes containing alkyl acrylates, triethylene glycol dimethacrylate, and liquid electrolyte were prepared by in situ thermal polymerization. The gel polymer electrolytes containing 15 wt% polymer content and 85 wt% liquid electrolyte content with sufficient mechanical strength showed the high ionic conductivity around 5?×?10^?3 Scm^?1 at room temperature. The gel electrolytes containing different polymer matrices were prepared, and their physical observation and conductivity were discussed carefully. The cross-linking copolymer gel electrolytes of alkyl acrylates with other monomers were designed and synthesized. The results showed that copolymerization can improve the mechanical properties and ionic conductivities of the gel electrolytes. The polymer matrices of gels had excellent thermal stability and electrochemical stability. The scanning electron microscope analysis showed the gel electrolyte was the homogeneous structure, and the cross-linking polymer host was the porous three-dimensional network structure, which demonstrated the high conductivity of the gel electrolytes. The gel polymer Li-ion battery was prepared by this in situ thermal polymerization. The cell exhibited high charge-discharge efficiency at 0.1 C. The results of LiFePO4-PEA-Li cell and graphite-PEA-Li cell showed that gel polymer electrolytes have good compatibility with the battery electrodes materials.     

Electrochemical copolymerization of 9,10-dihydrophenanthrene and 3-methylthiophene and characterization of their copolymer with tunable fluorescence properties

Electrochemical copolymerization of 9,10-dihydrophenanthrene and 3-methylthiophene was successfully achieved in boron trifluoride diethyl etherate by direct anodic oxidation of the monomer mixtures. The structure and properties of the copolymers were investigated with ultraviolet–visible, Fourier transform infrared spectroscopy, ¹H nuclear magnetic resonance, fluorescence spectra, and thermal analysis. The novel copolymers had the advantages of both poly(9,10-dihydrophenanthrene) and poly(3-methylthiophene), such as good electrochemical behavior, good mechanical properties, and high electrical conductivity. Fluorescence spectroscopy studies revealed that the copolymers had good fluorescence properties, and the emitting properties of the copolymer could be parameters by changing the feed ratio of the monomer mixtures during the electrochemical polymerization.     

Preparation, structure, and electrochemistry of a polypyrrole film doped with manganese(III)-substituted Dawson-type phosphopolyoxotungstate

The fabrication, structure, electrochemical properties, and electrocatalytic properties of a manganese(III)-substituted Dawson-type phosphopolyoxotungstate, alpha 2-K7P2W17O61(Mn3+.OH2).12H2O (P2W17Mn), entrapped in polypyrrole (PPy) film have been studied. The hybrid film was prepared by potentiostatic polymerization from aqueous solution containing 20 mM pyrrole (Py) and 2 mM P2W17Mn on a pyrolytic graphite (PG) surface. Chronoamperometry, Raman spectroscopy, UV-visible absorption spectroscopy, and cyclic voltammetry were used to monitor and characterize the growth, structure, and properties of the film. The chronoamperometric curve shows that P2W17Mn can catalyze the electrochemical polymerization of Py. The Raman spectrum suggests that the doped P2W17Mn has little effect on the structure of PPy film. The P2W17Mn/PPy film exhibits good voltammetric response in both the acidic aqueous and acetonitrile solutions. At pH 1.0, the molar ratio of pyrrole to P2W17Mn7- in the hybrid film is 21.1:1, quite close to the expected ratio of 21.2:1 for a PPy film with a +0.33 oxidation level per pyrrole moiety and doped with an anion with a charge of 7. The influence of solution pH on P2W17Mn7- in the film is much smaller than that in the aqueous solution. During the potential scanning in 0.1 M LiClO4 acetonitrile solution, P2W17Mn7- was slowly released from the hybrid film and electrolyte ions (Li+ and ClO4-) were inserted into the film. This was identified by cyclic voltammetry and UV-visible spectroscopy. Additionally, the hybrid film can effectively catalyze the reduction of hydrogen peroxide and nitrite.