Adsorption and solar light decomposition of acetone on anatase TiO2 and niobium doped TiO2 thin films

Adsorption and solar light decomposition of acetone was studied on nanostructured anatase TiO2 and Nb-doped TiO2 films made by sol-gel methods (10 and 20 mol % NbO2.5). A detailed characterization of the film materials show that films contain only nanoparticles with the anatase modification with pentavalent Nb oxide dissolved into the anatase structure, which is interpreted as formation of substituted Nb=O clusters in the anatase lattice. The Nb-doped films displayed a slight yellow color and an enhanced the visible light absorption with a red-shift of the optical absorption edge from 394 nm for the pure TiO2 film to 411 nm for 20 mol % NbO2.5. In-situ Fourier transform infrared (FTIR) transmission spectroscopy shows that acetone adsorbs associatively with eta1-coordination to the surface cations on all films. On Nb-doped TiO2 films, the carbonyl bonding to the surface is stabilized, which is evidenced by a lowering of the nu(C=O) frequency by about 20 cm(-1) to 1672 cm(-1). Upon solar light illumination acetone is readily decomposed on TiO2, and stable surface coordinated intermediates are formed. The decomposition rate is an order of magnitude smaller on the Nb-doped films despite an enhanced visible light absorption in these materials. The quantum yield is determined to be 0.053, 0.004 and 0.002 for the pure, 10% Nb:TiO2, and 20%Nb:TiO2, respectively. Using an interplay between FTIR and DFT calculations we show that the key surface intermediates are bidentate bridged formate and carbonate, and H-bonded bicarbonate, respectively, whose concentration on the surface can be correlated with their heats of formation and bond strength to coordinatively unsaturated surface Ti and Nb atoms at the surface. The oxidation rate of these intermediates is substantially slower than the initial acetone decomposition rate, and limits the total oxidation rate at t>7 min on TiO2, while no decrease of the rate is observed on the Nb-doped films. The rate of degradation of key surface intermediates is different on pure TiO2 and Nb-doped TiO2, but cannot explain the overall lower total oxidation rate for the Nb-doped films. Instead the inferior photocatalytic activity in Nb-doped TiO2 is attributed to an enhanced electron-hole pair recombination rate due to Nb=O cluster and cation vacancy formation.     

Formation of the structure of cerium oxide-modified titanium dioxide

The formation of the structure of titanium dioxide containing 3–15 wt % CeO₂ in a wide temperature range (300–850°C) has been investigated by X-ray powder diffraction, electron microscopy, and adsorption methods. Modification of titanium dioxide with cerium oxide causes the formation of nanostructured Ce-Ti-O compounds consisting of incoherently intergrown fine anatase crystallites. The crystallites are separated by interblock boundaries in which cerium ions are stabilized. The nanostructure formed in the Ce-TiO₂ oxide system stabilizes the anatase phase, prevents the sintering of anatase particles at high temperatures, and allows modified anatase to retain a larger specific surface area and a higher porosity upon heat treatment than pure titanium dioxide does.     

The structure of multilayered titania nanotubes based on delaminated anatase

We constructed a truly nanotubular structure model of titania nanotubes based on delaminated anatase with realistic dimensions replicating those observed in experiments. It is shown that this nanotubular structure based on delaminated anatase produces an XRD pattern in excellent agreement with the observed spectrum and that the tube axis is along the [0 1 0] direction of the anatase structure. Preserving the atomic registry of delaminated anatase between adjacent layers is essential along the tube axis but unnecessary along the circumference. These understandings provide detailed information on the structure and morphology of hydrothermally synthesized titania nanotubes. The findings will help discern the complex surface chemistry of these materials.     

Aerosol-assisted fabrication of mesoporous titania spheres with crystallized anatase structures and investigation of their photocatalitic properties

We demonstrate practical aerosol-assisted approach to synthesize spherical mesoporous titania particles with high surface areas. Scanning electron microscopy observation of the spray-dried products clearly shows spherical morphology. To remove surfactants and enhance crystallinity, the spray-dried products are calcined under various temperatures. The crystalline structures inside the particles are carefully detected by wide-angle XRD measurements. With increase of the calcination temperatures, anatase crystal growth proceeds and transformation from anatase to rutile is occurred. The effect of various calcination temperatures on the mesostructures is also studied by using N₂ adsorption desorption isotherms. The mesoporous titania particles calcined at 350, 400, and 500 °C exhibit type IV isotherms with a capillary condensation step and shows a hysteresis loop, which is a characteristic of mesoporous materials. The reduction in the surface areas and the pore volumes is confirmed by increasing the calcination temperatures, while the average pore diameters are increased gradually. This is attributed to the distortion of the mesostructures due to the grain growth of the anatase phase and the transformation to the rutile phase during the calcination process. As a preliminary experimental photocatalytic activity, oxidative decomposition of acetaldehyde under UV irradiation is examined. The mesoporous titania calcined at 400 °C shows the highest photocatalytic activity, due to both high surface area and well-developed anatase crystalline phase.     

Block copolymer‐directed synthesis of porous anatase for lithium‐ion battery electrodes

A templating method is developed to produce porous nanocrystalline anatase materials for negative electrodes in lithium‐ion batteries (LIBs). Amphiphilic diblock copolymers are used to generate template films with phase‐separated internal structure. Subsequent swelling with acidified titanium(IV) bis(ammonium lactato) dihydroxide (TALH) solution yielded structured hybrid films. Upon heating, the formation of TiO₂ nanocrystals is induced, resulting in a three‐dimensional mesoporous structure directed by the bulk morphology of the polymer template. In comparison to commercial nanosized anatase, the structured anatase shows significant performance improvements in lithium‐ion coin cell batteries in terms of capacity, stability, and rate capability. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 1890–1896     

Stable hydrosols for TiO<Subscript>2</Subscript> coatings

The optimum processing parameters required to synthesize, by hydrolysis of titanium isopropoxide (TIP), highly stable hydrosols composed of nanoparticles of the smallest possible size, are deduced both from data available in literature and from our own experiments. The colloids prepared in these conditions are composed of aggregates of anatase (~90%) and brookite crystallites (5–6 nm). They are suitable for coatings and have long-term stability (more than one year) in terms of polymorphic composition, crystallite and agglomerate size. Stable sols composed solely of anatase crystallites (4 nm) can be prepared by partially complexing the TIP by acetylacetone before hydrolysis. It is not possible to produce porous films with these colloids because they are stabilized by electrostatic repulsion which causes the particles to organize themselves, during the drying step, to form materials with a close packed structure. However, coatings with controlled porosity can be prepared from these stable sols through the post addition of polymers, like PEG or block copolymers.     

Influence of the pore structure parameters of mesoporous anatase microspheres on their performance in lithium-ion batteries

Monodisperse mesoporous anatase microspheres were prepared by a combination of sol–gel and liquid–crystal template methods. With the change in annealing temperature, the pore structure parameters of samples were regulated. The influence of pore structure parameters on lithium-ion battery performance was systematically investigated. Results of electrochemical test and analysis demonstrated that the pore structure parameters significantly influenced the specific capacity, charging and discharging curves, rate capability, and cycle performance of the batteries. The first irreversible capacity increased with increased specific surface area. Materials with larger specific surface area showed better rate capability. When the average pore size was too small, the transport of Li⁺ in the electrolyte was impeded, which affected the rate capability of the materials. Based on the charging and discharging curves, the capacity of the plateau section corresponding to lithium insertion/extraction ions in the interstitial octahedral sites of anatase became smaller with increased specific surface area. By contrast, the capacity of the oblique line section corresponding to the Li⁺ insertion/extraction into/from the surface layer of anatase became larger. The pore volume influenced the cycling stability.     

Effect of the microstructure of the supported catalysts CuO/TiO<Subscript>2</Subscript> and CuO/(CeO<Subscript>2</Subscript>-TiO<Subscript>2</Subscript>) on their catalytic properties in carbon monoxide oxidation

The effect of the microstructure of titanium dioxide on the structure, thermal stability, and catalytic properties of supported CuO/TiO₂ and CuO/(CeO₂-TiO₂) catalysts in CO oxidation was studied. The formation of a nanocrystalline structure was found in the CuO/TiO₂ catalysts calcined at 500°C. This nanocrystalline structure consisted of aggregated fine anatase particles about 10 nm in size and interblock boundaries between them, in which Cu²⁺ ions were stabilized. Heat treatment of this catalyst at 700°C led to a change in its microstructure with the formation of fine CuO particles 2.5–3 nm in size, which were strongly bound to the surface of TiO₂ (anatase) with a regular well-ordered crystal structure. In the CuO/(CeO₂-TiO₂) catalysts, the nanocrystalline structure of anatase was thermally more stable than in the CuO/TiO₂ catalyst, and it persisted up to 700°C. The study of the catalytic properties of the resulting catalysts showed that the CuO/(CeO₂-TiO₂) catalysts with the nanocrystalline structure of anatase were characterized by the high-est activity in CO oxidation to CO₂.     

Effect of silicon dioxide on the formation of the phase composition and pore structure of titanium dioxide with the anatase structure

The formation of the structure of titanium dioxide modified with silicon dioxide, which was introduced as tetraethyl orthosilicate, was studied. It was found that the formation of the nanocrystalline structure of TiO₂ occurred upon the modification of titanium dioxide with silicon dioxide. This nanocrystalline structure of TiO₂ was formed by highly dispersed anatase particles of size 6–10 nm stabilized by silicon oxide layers, which were formed upon the decomposition of tetraethyl orthosilicate. An increase in the modifier concentration resulted in a deceleration of the growth of anatase particles and an increase in the temperature of the phase transition of anatase to rutile. It was found that the anatase phase in the samples containing 5–15 wt % SiO₂ was stable up to 1000°C. The stabilization of highly dispersed anatase particles facilitated the retention of the developed fine-pore structure of xerogels with a pore diameter of 4 nm up to 900°C.     

Synthesis and photoluminescence of well-dispersible anatase TiO2 nanoparticles

High-purity anatase TiO(2) nanoparticles were prepared using a low-temperature sol-gel route. The as-prepared sample was characterized by X-ray diffraction, transmission electron microscopy, infrared spectroscopy, thermogravimetric analysis, UV-vis spectroscopy, and photoluminescence. It is shown that the as-prepared sample crystallized in a pure anatase phase with an average crystallite size of about 7 nm, and the surfaces were highly hydrated. These nanoparticles were stabilized as a water suspension via the cooperation of DLVO force and surface hydration force. These suspensions showed characteristic band-gap emission at 397+/-1.5 nm, which is a little red-shifted compared with the band-gap energy of indirect electronic transition measured in the UV-vis absorption spectrum. These observations were explained by the light-induced relaxation of polar water molecules in the surface hydration layer.     

A structural and surface approach to size and shape control of sulfur-modified undoped and Fe-doped TiO2 anatase nano-materials

In situ synchrotron X-ray diffraction and diffuse reflectance infrared spectroscopy (DRIFTS) are combined to study the influence of sulfur on the crystallization of pure and Fe-doped titania nano-materials. Using these two tools we have investigated the effect of sulfur on the nucleation and growth processes of the anatase polymorph from amorphous powders and show how the addition of sulfur controls the primary particle size and shape of the materials. As well known, sulfur leads to the stabilization of the oxide particle size against sintering during thermal treatments and here we interpret the physico-chemical basis of such behaviour as an exclusive effect on grain growth kinetics, in turn linked to the dehydration of the surface layers of the materials. In addition this work shows that the presence of sulfur also affects the shape of the anatase particles, favouring the existence of (101)-type surfaces and elongated (along the c crystallographic axis) particles. This combined analysis of how sulfur influences morphological aspects of the anatase phase as it grows provides a basis for understanding of surface and chemical properties of anatase nano-powders that are highly dependent upon particle morphology.     

Sulfate Ions in Titania Polymorphs

Sol-gel titania was sulfated by using sulfuric acid as hydrolysis catalyst, or by impregnating with ammonium sulfate fresh samples prepared with nitric acid or ammonium hydroxide as hydrolysis catalyst. Samples were characterized with X-ray powder diffraction, infrared spectroscopy, thermogravimetry and atomic absorption spectroscopy. Sulfate ions were found anchored to brookite and anatase phases, because they have short O—O atomic bond lengths slightly larger than the largest O—O bond length of sulfate ion. Since the shortest O—O atomic bond in anatase is smaller than the one in brookite, the sulfate ions are then less deformed when they are anchored to anatase, and consequently more stable. Therefore when the sample temperature is raised, the brookite with sulfate ions was transformed mainly to anatase and not into rutile, which is the most probably transformation when these ions are not involved. Sulfate ions also hindered anatase and brookite crystallite growing and stabilized the crystalline structure of anatase. When the sulfate ions are lost the crystalline anatase phase is transformed into rutile, leaving a large number of vacancies that favored atom diffusion and consequently the growing of rutile crystallites. The crystalline evolution of the samples as a function of the annealing temperature is almost independent of the sulfating method.     

Study of the Stable Nanocrystalline TiO<Subscript>2</Subscript> Hydrosol and its Fractions

Nanodisperse TiO₂ hydrosol and two of its fractions stabilized by HCl are studied. The anatase nanocrystalline fractions are obtained by the stepped coagulation of the stable sol using dependence of coagulation thresholds on size of nanocrystallites. X-Ray investigation in small and wide angles of scattering has revealed that the anatase nanocrystallites have a shape of 2.5–3 nm thick elongated plates with 8–18 nm lateral sizes. The concentrated hydrosols with the reduced HCl content prepared from the anatase fractions are shown to form an ordered structure. Narrow fractions of TiO₂ nanocrystallites obtained from the stable hydrosols seem to be promising for the preparation of highly ordered structures with a nanometer periodicity.     

Adsorption configurations and energetics of BClx (x=0-3) on TiO2 anatase (101) and rutile (110) surfaces

This study investigates the adsorption and reactions of boron trichloride and its fragments (BClx) on the TiO2 anatase (101) and rutile (110) surfaces by first-principles calculations. The results show that the possible absorbates on the TiO2 anatase and rutile surfaces are very similar. The single- and double-site adsorption configurations are found for both anatase and rutile surfaces. The particular adsorbate feature on the anatase surface is its in-plane double-site adsorption by Ti and O from its sawtooth surface. The potential energy surface shows that BCl3 can be adsorbed on the O site for both the anantase and rutile surfaces and the most of the BClx reaction on both anatase and rutile surfaces are endothermic, except for the dissociative reaction on the rutile surface. The energy levels of the BClx reactions between the anatase and rutile surfaces show that the rutile surface has lower energy levels than those of anatase surface. This result reveals that the BClx dissociative adsorption more easily occurs on rutile surface than on anatase surface.     

Cluster Models of the VOx/TiO2 Supported Catalyst

Molecular structures of the active vanadium phase of the VO _x /TiO₂ supported catalyst are calculated in the framework of the cluster approximation of density functional theory (DFT). It is shown that vanadium can be stabilized on the anatase (001) surface both in the tetrahedral and octahedral coordinations with the formation of monoxo- and dioxovanadyl structures. The energy of the dioxovanadyl structure binding to the support surface is 600–800 kJ/mol. The formation of dioxovanadyl structures from monoxovanadyl ones with the formation of water molecules is energetically favorable. The effect of support on the electronic state and acidic properties of the supported vanadium phase is discussed.     

引入应力的锐钛矿TiO_2(001)薄膜的外延生长

锐钛矿TiO_2(001)(anataseTiO_2(001),简记为ATO)表面因其优异的催化活性受到了广泛的关注。理论计算结果表明,ATO表面应力导致的晶格畸变可能会增强该表面的催化活性。因此有必要研究应力对ATO表面结构的影响。本文利用BaTiO_3(001)(简记为BTO)与ATO之间存在较大的晶格失配度,将ATO薄膜外延生长在BTO衬底上从而引入应力,研究了存在应力情况下的ATO薄膜的结构特征。实验中,利用脉冲激光沉积方法在Nb掺杂的SrTi O_3(001)(简记为STO)单晶衬底上制备了ATO/BTO/STO外延薄膜。X射线衍射(XRD)和扫描透射电子显微术(STEM)结果表明,作为应力引入层的BTO薄膜厚度约为4–6nm时,能够部分地将应力引入到ATO薄膜中。X射线光电子能谱(XPS)结果显示,ATO薄膜合适的厚度应大于15 nm,从而降低从衬底反向扩散至表面的Sr和Ba原子的浓度;Ti 2p的高分辨XPS谱仅呈现出Ti~(4+)峰,表明ATO表面Ti原子为完全氧化的价态。ATO外延薄膜表面的扫描隧道显微术(STM)图像仍然呈现为(1×4)重构的结构,但在(1×4)重构的脊上存在明暗交替并具有一定周期性的特征。根据完全氧化的"增氧原子模型"(ad-oxygen model,AOM),脊上观察到的明暗交替特征可归因于表面应力导致的"TiO_2"空位缺陷结构。     

Novel porous anatase TiO2 nanorods and their high lithium electroactivity

We demonstrated a simple approach for the synthesis of a kind of novel porous anatase TiO₂ nanorods. The method is based on a reaction in composite-hydroxide eutectic system and normal atmosphere without using an organic dispersant or capping agent. The synthesis technique is cost effective, easy to control and is adaptable to mass production. This is the first time TiO₂ nanorods with a porous structure are fabricated by using this method. The as-prepared material was characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), high-resolution transmission electron microscopy (HRTEM), nitrogen adsorption and desorption experiments and electrochemical measurements. The results showed that the anatase TiO₂ nanorods obtained in our experiment have a large specific surface area with a porous structure which makes it have a potential application in catalysts and battery materials, especially in lithium ion batteries. In this study, we mainly tested their electrochemical performance as negative materials for lithium ion batteries. Further research to optimize synthesis conditions, particularly to develop their application in the field of catalysis is currently in progress.     

Nitrogen/gold codoping of the TiO2(101) anatase surface. A theoretical study based on DFT calculations

The interaction between implanted nitrogen atoms, adsorbed gold atoms, and oxygen vacancies at the anatase TiO(2)(101) surface is investigated by means of periodic density functional theory calculations. Substitutional and interstitial configurations for the N-doping have been considered, as well as several adsorption sites for Au adatoms and different types of vacancies. Our total energy calculations suggest that a synergetic effect takes place between the nitrogen doping on one hand and the adsorption of gold and vacancy formation on the other hand. Thus, while pre-implanted nitrogen increases the adsorption energy for gold and decreases the energy required for the formation of an oxygen vacancy, pre-adsorbed gold or the presence of oxygen vacancies favors the nitrogen doping of anatase. The analysis of the electronic structure and electron densities shows that a charge transfer takes place between implanted-N, adsorbed Au and oxygen vacancies. Moreover, it is predicted that the creation of vacancies on the anatase surface modified with both implanted nitrogen and supported gold atoms produces migration of substitutional N impurities from bulk to surface sites. In any case, the most stable configurations are those where N, Au and vacancies are close to each other.     

Synthesis of uniform layered protonated titanate hierarchical spheres and their transformation to anatase TiO2 for lithium-ion batteries

Layered protonated titanates (LPTs), a class of interesting inorganic layered materials, have been widely studied because of their many unique properties and their use as precursors to many important TiO(2)-based functional materials. In this work, we have developed a facile solvothermal method to synthesize hierarchical spheres (HSs) assembled from ultrathin LPT nanosheets. These LPT hierarchical spheres possess a porous structure with a large specific surface area and high stability. Importantly, the size and morphology of the LPT hierarchical spheres are easily tunable by varying the synthesis conditions. These LPT HSs can be easily converted to anatase TiO(2) HSs without significant structural alteration. Depending on the calcination atmosphere of air or N(2), pure anatase TiO(2) HSs or carbon-supported TiO(2) HSs, respectively, can be obtained. Remarkably, both types of TiO(2) HSs manifest excellent cyclability and rate capability when evaluated as anode materials for high-power lithium-ion batteries.     

Template evaporation method for controlling anatase nanocrystal size in ordered macroporous TiO2

The importance of pure-phase titanium oxide materials as catalysts, sensors, and photonic band-gap materials has been growing steadily. Recently, more attention has been focused on nanostructured titanium oxide showing controlled and periodic porosity on a nanometric scale. The nanocrystal size control of porous nanostructured titanium oxide in an anatase form is a crucial step for the organic template method. Simple template removal by evaporation in an inert atmosphere is reported in this article and compared with the calcination technique usually reported in the literature. The proposed method allows the formation of a double-porous (macro and meso) anatase phase. We demonstrate that it highly preserves the macropore order into a titanium oxide material and induces narrowly dispersed mesopores by controlling the nano-crystal size that is kept around 6 nm. For the proposed method, polystyrene beads are particularly suitable as templates, being evaporated in the temperature range of anatase existence. The final high surface area makes the materials appealing for applications as photocatalysts or sensors.