噻吨酮光物理和光化学行为对溶剂的依赖性

本文利用纳秒瞬态吸收光谱技术,在不同溶剂中,研究了噻吨酮的光物理和光化学行为. TX的激发三重态(³TX^*)涉及2种电子态,³nπ^*和³ππ^*态. 随着溶剂极性的增强,³ππ^*态的贡献加大. 在CH₃CN,CH₃CN/CH₃OH(1:1)和CH₃CN/H₂O(1:1)溶剂中,³TX^*的自猝灭速率常数k_sq逐渐减小. 这可能由于通过氢键形成的激基复合物阻碍了³TX^*的碰撞猝灭. 二苯胺通过电子转移还原³TX^*,生成TX^·-阴离子和DPA^·+阳离子自由基. 溶剂对该转移过程的影响不明显,表明TX的³nπ^*和³ππ^*态夺取电子的能力相近. 然而,溶剂的依赖性在TX^·-的猝灭过程中表现明显. 在强酸性条件下(pH=3.0),质子化的TX和非质子化的TX之间存在着动态平衡. 在激发光作用下,生成³TXH^+*,光谱上呈现出520 nm处的吸收峰.     

激光闪光光解研究二羟基蒽醌和腺嘌呤/胞嘧啶的电子转移反应

采用纳秒时间分辨的激光闪光光解技术研究了乙腈/水混合溶液中二羟基蒽醌和腺嘌呤或胞嘧啶之间的电子转移反应. 在355 nm紫外光作用下,经由系间窜跃产生的三重态二羟基蒽醌与两碱基分别发生电子转移反应,其中碱基作为典型的电子给体. 基于测量到的反应瞬态中间体的动力学淬灭速率,两个反应过程被认为分步进行,先电子转移之后发生质子转移反应. 通过研究表观淬灭速率与两个碱基浓度的依赖关系,分别得到了两个双分子间电子转移反应的速率常数,分别是9.0×10⁸ L/(mol·s) (胞嘧啶)、3.3×10⁸ L/(mol·s) (腺嘌呤).     

电子通量对ZnO/K2SiO3热控涂层光学性能的影响

 研究了电子通量对ZnO/K₂SiO₃热控涂层光学性能的影响。分别采用通量为5×10¹¹/cm²·s，8×10¹¹/cm²·s，1×10¹²/cm²·s 和5×10¹²/cm²·s的电子对试样进行辐照。电子辐照下涂层的光学性能发生了退化，并且发现了退化涂层在空气中的“漂白”现象。分析了ZnO/K₂SiO₃热控涂层光学性能的退化机制，同时讨论了电子通量对太阳光谱吸收系数的影响。实验结果发现，在5×10¹¹～1×10¹²/cm²·s的电子通量范围内，电子通量对ZnO/K₂SiO³热控涂层光学性能的影响相同。因此在这个电子通量范围内，采用加速地面试验来模拟空间的电子辐照效应是有效的。     

乙腈-水和乙二醇-水均相溶液中光诱导杜醌激发三重态与色氨酸、酪氨酸的氢原子转移反应

本文用激光闪光光解技术研究了光诱导生物醌杜醌激发三重态(³DQ^*)和色氨酸(Trp)与酪氨酸(Tyr)在乙腈-水(MeCN-H₂O)及乙二醇-水(EG-H₂O)均相溶液中的光化学反应,分析了反应的机理,并基于Stern-Volmer方法测量了反应速率常数. 光解DQ体系可以生成³DQ^*,³DQ^*与Trp、Tyr发生的氢原子转移反应占主导地位. 对于DQ/Trp/MeCN-H₂O和DQ/Trp/EG-H₂O溶液,³DQ^*与Trp反应生成杜醌中性自由基DQH^·、以碳为中心的色氨酸中性自由基Trp^·/NH和以氮为中心的色氨酸中性自由基Trp/N^·. 对于DQ/Tyr/MeCN-H₂O和DQ/Tyr/EG-H₂O溶液,³DQ^*与Tyr反应生成DQH^·和酪氨酸中性自由基Tyr/O^·. ³DQ^*与Trp、Tyr的氢原子转移反应速率常数都在10⁹ L·mol^-1·s^-1量级,反应近似受扩散控制. MeCN/H₂O均相溶液中³DQ^*与Trp、Tyr的反应速率常数要明显高于EG/H₂O均相溶液中的反应速率常数,这与Stokes-Einstein方程定性一致.     

维生素C对菲醌三重激发态的淬灭机理及动力学研究

用时间分辨电子自旋共振技术研究了乙二醇(EG)均相溶液和反胶束溶液中抗氧化剂维生素C(VC)对菲醌(PAQ)分子激发三重态³PAQ*的淬灭反应．利用反胶束模拟生物细胞和组织的生理环境．光解PAQ/EG-H₂O均相溶液,³PAQ*与溶剂分子EG之间发生氢转移反应．当体系中加入VC后,³PAQ*不仅从EG上夺氢,还从VC上夺氢,VC对³PAQ*的淬灭速率常数为1.409×10⁸ L/(mol·s), 反应受扩散控制． 在CTAB/EG-H₂O和AOT/EG-H₂O反胶束溶液中,³PAQ*和VC之间的夺氢反应发生在反胶束的水/油界面附近,³PAQ*扩散到油/水界面的过程降低了反应的速率．对于TX-100/EG-H₂O反胶束溶液, 由于PAQ增溶于亲水的聚氧乙烯链中,VC对³PAQ*的淬灭速率常数比CTAB/EG-H₂O和AOT/EG-H₂O反胶束中的都大,甚至比EG-H₂O均相溶液中的也略大．很强的VC负离子自由基As^-的CIDEP信号来源于³PAQ*与VC之间发生抽氢反应过程中的三重态机理自旋极化转移     

4-硝基联苯酚三重态质子化和去质子化过程中瞬态物种的指认

近年利用超快光谱技术对于4-硝基联苯酚(HO-Bp-NO₂)的研究发现,其在单重态和三重态时均会发生光致质子耦合电子转移(PCET)反应. 其瞬态吸收光谱450 nm处有一个独特的尖锐吸收带,但无羟基取代的对硝基联苯(Bp-NO₂)未观察到此现象. 本文利用酸性溶液作为外加可控质子供体,通过在强酸(∽10^-1 mol/L)和弱酸(∽10^-4 mol/L)溶液中的光谱和动力学结果,指认这个新吸收带为开壳层单重态O-Bp-NO₂H. 它是HO-Bp-NO₂的互变异构体,由三重态HO-Bp-NO₂中硝基氧得质子后羟基快速去质子产生. 动力学分析表明,非质子极性溶剂中三重态HO-Bp-NO₂与基态母体间还会发生PCET或先质子后电子转移生成自由基·O-Bp-NO₂. 这一反应与O-Bp-NO₂H竞争,导致其产率较低. 这些结果阐明了三重态HO-Bp-NO₂在非质子极性溶剂中的失活机制.     

N,N-二甲基硫代乙酰胺S3(ππ*)态的衰变动力学 (cited: 1)

采用共振拉曼光谱和完全活化空间自洽场方法研究了N,N-二甲基硫代乙酰胺在被激发至S₃(ππ^*)态后的衰减动力学. 指认了紫外吸收光谱和振动光谱. 获得了乙腈、甲醇和水溶剂中不同激发波长下的A带共振拉曼光谱,以探测Franck-Condon区域的结构动力学. 开展了CASSCF计算以确定低能单重激发态和锥形交叉点的电子激发能和优化几何结构. 通过共振拉曼强度分析和CASSCF计算获得了结构参数、A带结构动力学和S₃(ππ^*)态衰减机制. 提出了主要衰减通道为_3,FC(ππ^*)→S₃(ππ^*)/S₁(nπ^*)→_1(nπ^*).     

瞬态磷光发射光谱研究阿替洛尔与单线态氧反应的动力学

药物活性化合物阿替洛尔是一种β受体阻滞剂,若将其排放到地表水资源中会对人类健康和生态系统产生不利的影响. 受光驱动的直接光降解以及间接光降解法可以有效去除环境中的阿替洛尔. 在间接光降解方法中,¹O₂是降解阿替洛尔这类污染物的重要活性物种. 然而,关于阿替洛尔与¹O₂反应动力学的信息还比较缺乏,二者间的反应速率常数仍存在争议. 本文通过直接观察¹O₂在1270 nm处衰减动力学来研究阿替洛尔与¹O₂在不同溶剂中的反应速率常数：在重水中为7.0×10⁵ (mol/L)^-1·s^-1,在乙腈中为8.0×10⁶ (mol/L)^-1·s^-1,在乙醇中为8.4×10⁵ (mol/L)^-1·s^-1. 在极性强、给氢能力弱的溶剂中阿替洛尔与¹O₂的反应速率常数更大. 这些结果对光降解阿替洛尔等β受体阻滞剂提供相关动力学信息.     

四氯苯醌与嘧啶类核酸碱基的光化学氢抽取和电子转移反应

采用纳秒时间分辨的激光闪光光解实验技术,研究了四氯苯醌(TCBQ)分子与两种嘧啶核酸碱基(胸腺嘧啶和尿嘧啶)分子在355nm激发下的光化学反应动力学. 355 nm将TCBQ分子布居到激发三重态³TCBQ^*,高反应活性的³TCBQ^*与碱基分子发生两个平行的反应,氢抽取反应和电子转移反应,分别对应生成瞬态光谱上观测到的两个光反应产物TCBQH·和TCBQ·^-. 这两个反应同时生成的碱基自由基和碱基阳     

青蒿素光化学合成中二氢青蒿酸与单线态氧反应的动力学研究

青蒿素是一种优异的抗疟药,广泛用于临床医学. 但由于青蒿素天然来源的限制,青蒿素的化学合成一直受到高度关注. 二氢青蒿酸是合成青蒿素的关键前体. 二氢青蒿酸与单线态氧反应形成过氧化物是青蒿素光化学制备中的关键步骤,制约着青蒿素化学合成的产率. 然而关于二氢青蒿酸与单线态氧反应的重要动力学信息并未有报道. 本文通过光敏化法产生单线态氧,研究二氢青蒿酸与单线态氧之间的反应速率常数. 通过直接检测单线态氧在1270 nm处的发光衰减动力学,得出单线态氧与二氢青蒿酸在不同溶剂中的反应速率常数分别为：在CCl₄中为1.81×10⁵ (mol/L)^-1·s^-1,在CH₃CN中为5.69×10⁵ (mol/L)^-1·s^-1,DMSO中为3.27×10⁶ (mol/L)^-1·s^-1. 发现在三种溶剂中二氢青蒿酸与单线态氧的反应速率常数随着溶剂极性的增加而增加. 这些结果为优化青蒿素光化学合成的实验条件提供了基础知识,有助于提高青蒿素的合成效率.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.     

Fiber Modal Index Measurements Based on Fiber Gratings

A novel method based on fiber gratings for measuring the effective indices of fiber modes is proposed. The effective index difference between the core mode and a cladding mode was obtained by analyzing the interference fringe of a pair of cascaded long-period fiber gratings. In order to extract the core mode index from the measured index difference, an index matching oil immersion method is proposed. By analyzing the interaction between the cladding mode and the oil applied on the cladding surface, the mode order and the effective index of the involved cladding mode might be calculated. Experimental results about the interference fringe shifts induced by the oil index and the oil-applied length are also presented.     

Optical Pulse Compression Schemes That Use Nonlinear Bragg Gratings

Nonlinear optical pulse compression of picosecond pulses typically requires long lengths of optical fiber and multiple components. Periodic structures, such as fiber Bragg gratings, are highly dispersive at wavelengths outside of the photonic bandgap. This implies that such gratings can be used as very short all-fiber compressors. In this paper a number of such compression schemes are reviewed involving uniform and nonuniform fiber Bragg gratings, relying on both soliton and nonsoliton compression principles. Experimental results supporting the corresponding underlying theory are also presented. Finally, an extension of one of the compression schemes is shown, which allows the generation of adjustable high-repetition rate soliton trains.