The total surface free energy and the contact angle in the case of low energetic solids

Using the literature data of the refractive index, the structural unit molar volume of polymers and their dipole moment, as well as the literature data of the polarizability, ionization potential, and dipole moment of many liquids, values of the Φ parameter for paraffin—liquid and polymer—liquid interfaces were calculated. Next, introducing these values of Φ and the earlier measured values of the contact angle for many liquids to the Young equation, values of the surface free energy (γ_S) of paraffin, polytetrafluoroethylene (PTFE), polyethylene (PE), polyethylene terephthalate (PET), and polymethacrylate (PMMA), were determined. It was found that the average values of γ_S for these solids were in agreement with those calculated on the basis of geometric, harmonic, or harmonic—geometric mean approaches. The values of the surface free energy of paraffin, PTFE, PE, PET, and PMMA were also calculated from the Young equation modified by Neumann et al. and, using the earlier measured values of the contact angle for many liquids, they were compared with the values obtained by other methods. Next, employing the mean value of the surface free energy, values of the contact angles for many liquids were calculated and compared with those measured earlier for the same liquids. It was found that for paraffin, PTFE, and PE there were big differences among the values of their surface free energies calculated from the contact angles for some liquids; however, the average values were in agreement with those obtained by other methods. The average values of the surface free energies of PET and PMMA were also in the range of the results obtained by other authors. It was also found that the average deviations of the contact angles calculated from the Young equation modified by Neumann et al. from the measured ones were slightly larger than those of the contact angles calculated from equations employing the geometric and harmonic means of the surface free energy components; the method of Neumann et al. may also be used to predict the wettability in some systems.     

含氟丙烯酸酯共聚乳液及其膜表面特性的研究

以十二烷基硫酸钠 (SDS)和OP 10混合乳化剂 ,制备了甲基丙烯酸全氟辛基乙酯 (FMA8) 甲基丙烯酸丁酯 (BMA) 甲基丙烯酸 (MAA)共聚乳液 .通过DSC、FT IR、1 H NMR对共聚物的结构、组成进行了表征研究 .采用JZHY 180界面张力仪研究了共聚乳液膜表面的性质 ,结果表明 ,随着共聚物中全氟单体含量的增加 ,共聚物膜的表面能显著降低 ,当全氟单体的含量达到 2 5wt %时 ,其表面能降低到 19 74mJ m2 .X ray光电子能谱(XPS)对共聚物表面原子组成的分析结果表明 ,共聚物表面氟的含量远高于其平均含量 ,证明了含氟基团的趋表现象 .经退火处理 ,共聚物膜表面的氟含量增加 ,表面自由能降低     

Relationship between heat of immersion and surface Gibbs energy of fluorite and cassiterite

Calorimetric measurements were made of the heat of immersion in water of cassiterite that was either untreated or treated with 60% HNO₃. The heats of immersion of cassiterite and fluorite were also calculated theoretically from the surface Gibbs energy components, and compared with the heat of immersion measured for cassiterite and that taken from the literature for fluorite. The results of the measurements and calculation revealed that the heat of immersion depends on the degree of hydration of the surface of cassiterite and fluorite. It was also found that it is possible to predict the heats of immersion in water of cassiterite and fluorite from the Lifshitz-van der Waals and acid-base components of the surface Gibbs energy.     

Investigation into pH-responsive self-assembled monolayers of acylated anthranilate-terminated alkanethiol on a gold surface

This article describes the preparation of pH-responsive self-assembled monolayers (SAMs) of acylated anthranilate-terminated alkanethiol. These monolayers are formed by chemisorption of the alkanethiol molecules onto a gold surface, resulting in different wetting properties of the surfaces depending upon the pH. By using various characterization techniques (e.g., infrared spectroscopy, cyclic voltammetry, contact angle measurements, and surface energy analysis), we have found that the changes in the wetting properties originate from the different surface structures of the monolayers in different pH environments. From surface energy analysis, we found that the disperse components of the surface energy on such SAMs predominate after treatment with pH 1 water, whereas the polar components of the surface energy on such SAMs predominate after treatment with pH 13 water. It is greatly anticipated that this line of research will provide new insight into the mechanism behind pH-responsive properties, facilitating the design and synthesis of new surface-active molecules for the fabrication of pH-responsive functional surfaces.     

Wettability of tri-block copolymer coated hydrophobic surfaces Predictions and measurements

Hydrophobic surfaces with adsorbed tri-block copolymers are wetted by oil in spite of the hydrophilic buoy groups of the block copolymer that are present near the surface. The effect of the buoy group length of the adsorbed molecules on the wettability of hydrophobic surfaces is studied by contact angle measurements and by computer modelling.

The computer model predicts an increase in interfacial free energy with increasing buoy group length for equilibrium adsorption of block copolymer from water. Molecules with large buoy groups occupy more lateral space; therefore the “bare” surface gets more exposed and the anchor groups contribute less to the interfacial free energy which thus increases with the buoy group length.

The calculations showed that the variation of the interaction parameter between solvent and buoy group hardly influences the interfacial free energy. In contrast the interaction parameter between solvent and surface influences the interfacial free energy to a large extent because the oil/surface interactions have a lower energetic value as compared to water/surface interactions and therefore the interfacial free energy is lower than in water. The interfacial free energy varies slightly with increasing buoy group length, depending on the value chosen for the solvent/surface interaction parameter.

Advancing and receding contact angles of hexadecane, sunflower oil and hydrolysate (partly hydrolysed sunflower oil) were measured on hydrophobic surfaces. All oil/water contact angles were small, indicating a hydrophobic apolar surface character. It was found that, for oils with a “good” interaction with the surface (hexadecane and sunflower oil), the contact angle has a minimum value at a certain buoy group length. For hydrolysate (less-strong interaction with the surface) the contact angle decreases monotonically with increasing buoy group length. The results for hexadecane, sunflower oil and hydrolysate are in reasonable agreement with the model predictions. The effect of increasing buoy group length is weak; both decreasing and increasing angles are found, depending on the type of oil used.     

Surface free energy of sulfur--revisited I. Yellow and orange samples solidified against glass surface

Surface free energy of two different samples of solidified sulfur (yellow and orange) was investigated, using several approaches for its determination. It was found that values determined about two decades ago for surface free energy of sulfur were overestimated. From current studies the apparent value of this energy ranges between 30 and 60 mJ/m(2), depending on the kind and age of the sulfur samples (up to 1 year old) and/or the probe liquid used for the advancing and receding contact angle measurements. The energy has been calculated from van Oss et al.'s approach (Lifshitz-van der Walls, electron-donor, and electron-acceptor components), the contact angle hysteresis approach proposed by Chibowski, the equation of Owens and Wendt (dispersion and polar components), and Neumann et al.'s equation of state, as well as from equilibrium contact angle using Tadmor's procedure. The lowest values of the energy for 3-day- and 3-month-old samples of sulfur were calculated from the equation of state; they were below the range mentioned above.     

Foam films stabilized with alpha olefin sulfonate (AOS)

Alpha olefin sulfonate (AOS) surfactants have shown outstanding detergency, lower adsorption on porous rocks, high compatibility with hard water and good wetting and foaming properties. These properties make AOS an excellent candidate for foam applications in enhanced oil recovery. This paper summarizes the basic properties of foam films stabilized by an AOS surfactant. The foam film thickness and contact angle between the film and its meniscus were measured as a function of NaCl and AOS concentrations. The critical AOS concentration for formation of stable films was obtained. The critical NaCl concentration for formation of stable Newton black films was found. The dependence of the film thickness on the NaCl concentration was compared to the same dependence of the contact angle experiments. With increasing NaCl concentration the film thickness decreases gradually while the contact angle (and, respectively the free energy of film formation) increases, in accordance with the classical DLVO theory.The surface tension isotherms of the AOS solutions were measured at different NaCl concentrations. They coincide on a single curve when plotted as a function of mean ionic activity product. Our data imply that the adsorption of AOS is independent of NaCl concentration at a given mean ionic activity.     

Foam films stabilized by dodecyl maltoside. 1. Film thickness and free energy of film formation

Foam films stabilized by a sugar-based nonionic surfactant, beta-dodecyl maltoside, are investigated. The film thickness and the film contact angle (which is formed at the transition between the film and the bulk solution) are measured as a function of NaCl concentration, surfactant concentration, and temperature. The film thickness measurements provide information about the balance of the surface forces in the film whereas the contact angle measurements provide information about the specific film interaction free energy. The use of the glass ring cell and the thin film pressure balance methods enables studies under a large variety of conditions. Thick foam films are formed at low electrolyte concentration. The film thickness decreases (respectively the absolute value of the interaction film free energy increases) with the increase of the electrolyte concentration according to the classical DLVO theory. This indicates the existence of a repulsive double layer electrostatic component of the disjoining pressure. An electrostatic double layer potential of 16 mV was calculated from the data. A decrease of the film thickness on increase of the surfactant concentration in the solution is observed. The results are interpreted on the basis of the assumption that the surface double layer potential originates in the adsorption of hydroxyl ions at the film surfaces. These ions are expelled from the surface at higher surfactant concentration.     

PREPARATION AND SURFACE PROPERTIES OF ACRYLIC COPOLYMERS CONTAINING FLUORINATED MONOMERS

A series of copolymers comprising butylmethacrylate, styrene, butylacrylate, hydroxypropyl acrylate and perfluoroalkyl methacrylate were synthesized by the free radical polymerization using BPO as an initiator. The surface property of the copolymer films was subsequently characterized. The contact angle measurements and energy dispersive analysis of X-ray （EDAX） show that the length and content of perfluoroalkyl side chains in the copolymers are crucial for the preparation of the film with low surface energy. At a given content of fluorinated monomers in the copolymers, the longer the perfluoroalkyl side chain, the larger the water contact angle of the copolymer films will be. On the other hand, the higher the content of fluorinated monomers, the lower the surface energy is. The water contact angle increases with the increase of the fluorinated monomer content and reaches a plateau at 3 wt% of fluorinated monomer content.     

Surface modification of PET films by atmospheric pressure plasma exposure with three reactive gas sources

The surface modification of poly (ethylene terephthalate) (PET) film was carried out using an atmospheric pressure plasma (APP) jet device with three reactive gases: air, N₂, and Ar. The water contact angles on the PET film were found to decrease considerably after the APP exposure. The changes in the advancing and receding contact angles of water on the APP-exposed PET film with aging time were examined by the wetting force measurements employing the Wilhelmy method. The hydrophobic recovery due to the rinsing with water as well as the aging in air was observed only for the advancing angle, which was probably caused by the dissolution of low molecular weight oxidized materials into water, the loss of volatile oxidized species to the atmosphere and the reorientation and the migration of polymer chains. The wettability and the surface free energy of the APP-exposed PET film after diminishing hydrophobic recovery was sufficiently large compared with the untreated film. X-ray photoelectron spectroscopy confirmed that the PET film surface was oxidized due to the APP exposure. When N₂ gas was used for the APP exposure, the surface nitrogen concentration was found to increase with decreasing D. The surface oxygen concentration on the APP-exposed PET film was reduced by rinsing with water, in accordance with the hydrophobic recovery behavior. From atomic force microscopy, surface topographical change due to the APP exposure was observed. The changes in the PET surface properties due to the APP exposure as mentioned above were remarkable for using N₂ gas.     

一种可溶性低表面自由能聚合物的制备及其表面性质

用全氟辛酸和甲基丙烯酸羟丙酯 (HPMA)为原料 ,合成了具有低表面自由能 ( 1 4 2mN m)的聚合物聚甲基丙烯酸全氟辛酰氧丙基酯 (PFPMA) ,接触角的测定表明聚合物具有较好双疏性 (疏水 疏油性 ) ,其对水的接触角高达 1 1 5°,对正十六烷的接触角为 75°.     

Effect of Cationic and Zwitterionic Surfactants on Contact Angle of Quartz–Water–Crude Oil System

The influences of four cationic surfactants hexadecyl glycidyl ether ammonium chloride and four zwitterionic surfactants hexadecyl glycidyl ether glycine Betaine solutions on contact angle of crude oil on a quartz surface were investigated using a captive drop method. The effects of surfactant type, structure, and concentration on contact angle were expounded. From obtained results it appears that the adsorbed surfactant at oil–water interface reduces the interfacial tension and the adsorption at quartz–water interface improves interfacial free energy, which results in reducing the stable value of contact angle and weakening dynamic behavior. At high concentration, the zwitterionic surfactant with branched-chain may form semi-micelle at quartz surface. As a result, the stable value of contact angle passes through a sharp minimum with the increasing concentration.     

Effect of surface oxyfluorination on the dyeability of polyethylene film

The effect of surface oxyfluorination on low-density polyethylene (LDPE) film was studied in terms of surface functionality and surface energetics of the film surfaces, which can be attributed to improvement of the dyeability. The growth of functional groups and surface free energy was confirmed by FTIR-ATR, XPS, and contact angle methods. As a result, the total surface free energy was increased with oxyfluorination time, as a progressive increase of the polar component together with a small decrease of the dispersive component of surface free energy. From the dyeability test using the Kubelka-Munk equation, it was found that the oxyfluorination treatment plays an important role in the growth of oxygen-containing functional groups of LDPE film, resulting in improving the dyeability with a basic dyeing agent. A direct linear relationship is shown between the specific component of surface free energy and the K/S value for this work.     

Correlation between surface free energy of quartz and its wettability by aqueous solutions of nonionic, anionic and cationic surfactants

The measurements of the advancing contact angle for water, glycerol, diiodomethane and aqueous solutions of Triton X-100 (TX-100), Triton X-165 (TX-165), sodium dodecyl sulfate (SDDS), sodium hexadecyl sulfonate (SHDS), cetyltrimethylammonium bromide (CTAB) and cetylpyridinium bromide (CPyB) on quartz surface were carried out. On the basis of the contact angles values obtained for water, glycerol and diiodomethane the values of the Lifshitz–van der Waals component and electron-acceptor and electron-donor parameters of the acid–base component of the surface free energy of quartz were determined. The determined components and parameters of the quartz surface free energy were used for interpretation of the influence of nonionic, anionic and cationic surfactants on the wettability of the quartz. From obtained results it was appeared that the wettability of quartz by nonionic and anionic surfactants practically does not depend on the surfactants concentration in the range corresponding to their unsaturated monolayer at water–air interface and that there is linear dependence between adhesional and surface tension of aqueous solution of these surfactants. This dependence for TX-100, TX-165, SDDS and SHDS can be expressed by lines which slopes are positive. This slope and components of quartz surface free energy indicate that the interaction between the water molecules and quartz surface might be stronger than those between the quartz and surfactants molecules. So, the surface excess of surfactants concentration at the quartz–water interface is probably negative, and the possibility of surfactants to adsorb at the quartz/water film–water interface is higher than at the quartz–water interface. This conclusion is confirmed by the values of the adhesion work of “pure” surfactants, aqueous solutions of surfactants and water to quartz surface. In the case of the cationic surfactants the relationship between adhesional and surface tension is more complicated than that for nonionic and anionic surfactants and indicates that the relationship between the adsorption of the cationic surfactant at water–air and quartz–water interface depends on the concentration of the surfactants in the bulk phase.     

Contact angles in thin liquid films : III. Interaction forces in Newton black soap films

The interaction parameters of Newton black soap films stabilized by NaDS, as derived from contact angle experiments, have been interpretated in terms of the structure and the interaction forces in the films. From the film thickness and the difference between the surface excess of the salt in the film and at the bulk surface it is concluded that (a) the diffuse double-layer overlap in the film is practically complete; (b) the film only contains absorbed DS⁻ ions and an equal amount of Na⁺ counterions, but no salt; and (c) the double layer at the bulk surface is still partly diffuse. A model for the structure of the NB films is proposed according to which the adsorbed DS⁻ ions with their counterions form a two-dimensional square lattice at each film surface. It is found that the interaction free energy of the NB films can be explained by taking into account the electrostatic interactions between the discrete ions in the two opposing surface lattices. The model of the NB film is qualitatively in agreement with the experimental results of other workers.     

具有低表面自由能有机介电薄膜的制备及表征

通过自主开发的有机镀膜技术在Mg-Mn-Ce镁合金表面制备了具有低表面自由能和较高介电常数的有机纳米薄膜. 利用X射线光电子能谱(XPS)分析了表面有机镀膜过程的反应机理, 借助傅里叶变换红外(FT-IR)光谱进一步确认表面有机膜层的存在, 采用接触角测量仪测定了有机薄膜的蒸馏水接触角和表面自由能变化, 使用椭圆偏振光谱仪研究了薄膜的厚度, 并借助精密阻抗分析仪评价了薄膜的介电性能. 有机镀膜后镁合金表面形成了一层纳米级厚度的有机薄膜, 接触角从基体的70.8°上升至150.5°, 表面自由能从基体的37.96 mJ·m^-2降低到1.57 mJ·m^-2, 镁合金表面从亲水性转变为疏水性; 薄膜的厚度和质量随有机镀膜时间延长先增加后有所减小, 在镀膜20 min时薄膜性能最佳, 此时膜重达到23.5 μg·cm^-2, 膜厚最大为147.48 nm, 其相对介电常数也达到最大, 在1 kHz下可达24.922.     

盐酸溶液中阴离子表面活性剂在铝表面上的吸附

用失重法研究了盐酸溶液中阴离子表面活性剂十二烷基磺酸钠（ＤＳＡＳＳ），十二烷基苯磺酸钠（ＤＢＳＡＳ）以及十二烷基硫酸钠（ＳＤＳ）在铝表面上的吸附作用，提出这种吸附作用与铝的失重量有关，且符合Ｌａｎｇ－ｍｕｉｒ方程，计算出吸附热，吸附熵和吸附自由能等热力学参数。认为这种吸附主要靠静电作用，根据接触角的变化讨论了阴离子表面活性剂分子在铝表面上的吸附取向。     

表面接枝含氟苯乙烯共聚物的聚酯薄膜制备与表征

利用表面引发原子转移自由基聚合(SI-ATRP)在聚对苯二甲酸乙二醇酯(PET)薄膜表面接枝苯乙烯和4-氟苯乙烯的共聚物.研究不同反应时间和不同配比下接枝共聚物对聚酯薄膜表面组成、结构和性能的影响.通过傅利叶变换红外光谱仪(ATR/FTIR),X-射线光电子能谱仪(XPS),凝胶渗透色谱(GPC)和扫描电子显微镜(SEM)对接枝改性前后PET薄膜的表面组成,结构和形貌进行分析;利用接触角测试和表面能计算对比研究接枝改性前后PET薄膜的表面性能.结果表明反应时间和单体百分含量对接枝百分率及接触角有一定的影响,随着反应时间的增长,聚酯薄膜表面接枝百分率增大,接触角增加,表面自由能下降.     

The physicochemical surface characteristics of Brevibacterium linens

The physicochemical surface characteristics and interfacial behavior of two strains of Brevibacterium linens (BL-MGE and BL-9174), that may enhance cheese flavor, were assessed. Cell surface hydrophobicity was determined by measuring the contact angle of a variety of polar and non-polar wetting agents on lawns of the bacterial cells. The contact angles obtained were used to calculate the cell surface free energy components γ^LW, γ^AB, γ⁺ and γ⁻. The Lifshitz van der Waals component and the Lewis acid-base component were approximately 35 mJ m⁻² and 22 mJ m⁻², respectively, for both strains. Under conditions of physiological pH and low ionic strength, neither strain exhibited affinity for an octyl ligand in hydrophobic interaction chromatography. This occurred despite a favorable free energy of interfacial interaction which was attributable almost entirely to favorable acid-base interactions between cells and octyl-sepharose. The nature of surface functional groups was evaluated using X-ray photoelectron spectroscopy. Excluding H, the mean percentage of atomic fraction for C, O, N and P for BL-MGE was 57.7, 37.8, 3.9 and 0.6%, respectively and 61.0, 31.8, 7.0 and 0.2%, respectively for BL-9174.     

MICROPHASE SEPARATED STRUCTURES AND PROPERTIES OF PDMS-MDI-PEG COPOLYMER SURFACE

A series of poly(dimethylsiloxane)(PDMS)-4,4′-diphenylmethanediisocyanate(MDI)-poly(ethylene glycol)(PEG) multiblock copolymers were synthesized by employing two-step growth polymerization and investigated by AFM,XPS. contact angle system,protein adsorption and platelets adhesion measurements,respectively.It was found that as the molecular weight of PDMS increased,the surface of copolymers had increasing phase separation,while the increase in the molecular weight of PEG decreased the phase separation ext...