Rubbery copolymer electrolytes containing polymerized ionic liquid for dye-sensitized solar cells

A novel type of random copolymer comprised of a polymerized ionic liquid, poly(1-((4-ethenylphenyl)methyl)-3-butyl-imidazolium iodide) (PEBII), and amorphous rubbery poly(oxyethylene methacrylate) (POEM) was synthesized and employed as a solid electrolyte in an I₂-free dye-sensitized solar cell (DSSC). The copolymer electrolytes deeply infiltrated into the nanopores of mesoporous TiO2 films, resulting in improved interfacial contact of electrode/electrolyte. The glass transition temperature (T _g) of the PEBII–POEM (?23 °C) was lower than that of PEBII homopolymer (?4 °C), indicating greater chain flexibility in the former. However, the DSSC efficiency of PEBII–POEM (4.5 % at 100 mW/cm²) was lower than that of PEBII (5.9 %), indicating that ion concentration is more important than chain flexibility. Interestingly, upon the introduction of ionic liquid, i.e., 1-methyl-3 propylimidazolium iodide, the efficiency of PEBII remained almost constant (5.8 %), whereas that of PEBII–POEM was significantly improved up to 7.0 % due to increased I^? ion concentration, which is one of the highest values for I₂-free DSSCs.     

Effect of pore size/distribution in TiO2 films on agarose gel electrolyte-based dye-sensitized solar cells

This study develops a simple method to change the distribution of the pore size in a TiO₂ layer, using polyethylene glycol (PEG), while maintaining nearly the same surface area and porosity to clarify how large pores affect the performance of dye-sensitized solar cells (DSSCs). Specifically, a heating step at 100 °C for a specific duration is added prior to PEG removal and TiO₂ sintering at 400 °C. This process transforms the role of the PEG from a surfactant to a pore generator (porogen) and forms larger pores, depending on the loading and aggregation time for the PEG to gain larger pores. The effect of larger pores in TiO₂ films under 30 % PEG loading, on the performance of an agarose gel electrolyte-based DSSC, was further investigated using the ionic liquid, 1-allyl-3-ethylimidazolium iodide (AEII). The I–V characteristic and the electrochemical impedance spectroscopy analysis show that larger pores readily improve redox couple diffusion in a TiO₂ porous electrode and modify the interface between electrolyte and TiO₂. Using the optimized TiO₂ film with larger pores (30 % PEG loading, 100 °C/60 min), an efficiency of 7.43 % is achieved for the agarose gel electrolyte-based DSSC, which represents a 26.1 % improvement over TiO₂ without the addition of PEG.     

A highly efficient electric additive for enhancing photovoltaic performance of dye-sensitized solar cells

N-cetylpyridinium iodide (N-CPI) as a new electric additive for enhancing photovoltaic performance of the dye-sensitized solar cell (DSSC) was studied. It showed high efficiency for enhancing both the open-circuit voltage and the short-circuit current density of DSSC when the suitable amount of N-CPI as 0.02 M was added in liquid electrolyte. The energy conversion efficiency of DSSC increased from 4.429% to 6.535%, with 47.55% enhancement. Therefore, it is a highly efficient electric additive for DSSC. The intrinsic reason is owing to the special molecular structure of N-CPI, which contains two different polarity groups. As a surfactant, N-CPI could form ordered arrangement in liquid electrolyte, which affects the diffusing ability and the redox reaction of I^?/I ₃ ^? , and further affects the photovoltaic performance of DSSC.     

Ionic Liquid Based Electrolyte with Mesoporous Silica SBA-15 as Framework for Quasi-solid-state Dye-sensitized Solar Cells

Quasi-solid-state electrolytes were fabricated with mesoporous silica SBA-15 as a framework material. Ionic conductivity measurements revealed that SBA-15 can enhance the conductivity of the quasi-solid-state electrolyte. The diffusion coefficients of polyiodide ions such as Ⅰ3ˉ and Ⅰ5ˉ which were confirmed by Raman spectroscopic measurement, were about twice larger than that of I-. The optimized photoenergy conversion efficiency of dye-sensitized solar cells （DSSC） with the quasi-solid-state electrolyte was 4.3% under AM 1.5 irradiation at 75 mW·cm^-2 light intensity.     

Ternary diffusion with charged-complex formation in aqueous I2+NaI and I2+KI solutions

Diaphragm cells have been used to measure ternary diffusion coefficients for I₂+NaI and I₂+KI in aqueous solution at 25°C. Although most of the iodine molecules are bound to iodide ions and are transported as the triiodide species [I₂(aq)+I^–(aq)=I ₃ ^– (aq)], diffusion of the iodide salts produces relatively small countercurrent coupled flows of the iodine component. The ternary diffusivity of the iodine component in the solutions is 10 to 20% larger than the diffusivity of the triiodide species. This behavior can be understood by considering electrostatic coupling of the ionic flows. The diffusion equations for I₂+NaI and I₂+KI components are reformulated in terns of NaI₃+NaI and KI₃+KI mixed electrolyte components.     

Influence of amylopectin in dimethylsulfoxide on the improved performance of dye-sensitized solar cells

A highly viscous liquid electrolyte is prepared by adding a small amount of amylopectin into dimethylsulfoxide solvent. By using this viscous electrolyte, a dye-sensitized solar cell (DSSC) enhances the short-circuit photocurrent density and solar-to-electricity conversion efficiency by 22% and 8.4%, respectively, compared to those obtained with the reference cell without amylopectin. Furthermore, the stability of the DSSC is enormously improved by the addition of amylopectin. Polarization curves indicate that amylopectin is a reasonable corrosion inhibitor for silver metal in the electrolyte containing I₃^?/I^? couple.     

The effect of ionic strength on the diffusion of 125I in Gaomiaozi bentonite

The diffusion of ¹²⁵I^? in compacted Gaomiaozi (GMZ) bentonite was investigated by capillary in-diffusion method. Apparent and effective diffusion coefficients and accessible porosity of iodide in GMZ bentonite were obtained, and the effect of ionic strength on diffusion parameters was studied. The apparent diffusion coefficients of iodide in compacted GMZ bentonite are in the range of 1.0–6.0 × 10^?10 m² s^?1 under the conditions of dry bulk density 1,500 kg m^?3 and temperature 298 K, and increase with increasing ionic strength. This effect was explained through the analysis of microscopic structure of compacted bentonite. The iodide can only diffuse in unbound interparticle pore solution of compacted bentonite. The apparent diffusion coefficient is a function of accessible porosity which is decided by the thickness of diffusion double layer, and the thickness is in turn controlled by ionic strength.     

Quantum dot doped solid polymer electrolyte for device application

ZnS capped CdSe quantum dots embedded in PEO:KI:I₂ polymer electrolyte matrix have been synthesized and characterized for dye sensitized solar cell (DSSC) application. The complex impedance spectroscopy shows enhance in ionic conductivity (σ) due to charges provide by quantum dots (QD) while AFM affirm the uniform distribution of QD into polymer electrolyte matrix. Cyclic voltammetry revealed the possible interaction between polymer electrolyte, QD and iodide/iodine. The photovoltaic performances of the DSSC containing quantum dots doped polymer electrolyte was also found to improve.     

β‐Pyridinium di­chloro­iodide

The β modification of pyridinium di­chloro­iodide, C₅H₆N⁺·Cl₂I^?, was obtained as yellow crystals by the reaction of (C₅NH₅)AuCl₃, C₅H₆N⁺·Cl^? and I₂ in a vacuum‐sealed ampoule. The di­chloro­iodide ion is nearly symmetric and linear with I—Cl bond lengths of 2.544 (3) and 2.550 (3) Å and a Cl—I—Cl angle of 179.68 (12)°.     

Electrochemistry of iodine and iodide in chloroaluminate melts

The electrochemical behavior of iodine and iodide has been studied in AlCl₃+NaCl mixtures with compositions ranging from NaCl saturated melts to AlCl₃+NaCl (63+37 mol %) at platinum and tungsten electrodes. Iodide is oxidized in two steps to iodine and I(I); a reduction wave to iodide and an oxidation wave to I(I) are obtained in iodine solutions. The equilibrium constant for the reaction, I^?+I(I)=I₂, is 6×10⁸ l mol^?1 in molten chloroaluminate melts at 175°C.     

Bis(2‐chloro‐N‐methyl­pyridinium) iodide triiodide

The title compound, 2C₆H₇ClN⁺·I^?·I₃^?, crystallizes with undulating layers of chains containing alternate iodide and triiodide anions formed from iodine and the heterocyclic iodide salt.     

Study of lithium ion intercalation/de-intercalation into LiNi1/3Mn1/3Co1/3O2 in aqueous solution using electrochemical impedance spectroscopy

The mechanism of lithium ion intercalation/de-intercalation into LiNi_1/3Mn_1/3Co_1/3O₂ cathode material prepared by reactions under autogenic pressure at elevated temperatures method is investigated both in aqueous and non-aqueous electrolytes using electrochemical impedance spectroscopy (EIS) technique. In accordance with the results obtained an equivalent circuit is used to fit the impedance spectra. The kinetic parameters of intercalation/de-intercalation processes are evaluated with the help of the same equivalent circuit. The dependence of charge transfer resistance (R _ct), exchange current (I ₀), double layer capacitance (C _dl), Warburg resistance (Z _w), and chemical diffusion coefficient (D _Li+) on potential during intercalation/de-intercalation is studied. The behavior of EIS spectra and its potential dependence is studied to get the kinetics of the mechanism of intercalation/de-intercalation processes, which cannot be obtained from the usual electrochemical studies like cyclic voltammetry. The results indicate that intercalation and de-intercalation of lithium ions in aqueous solution follows almost similar mechanism in non-aqueous system. D _Li+ values are in the range of 10^?8 to 10^?14?cm²?s^?1 in aqueous 5?M LiNO₃ and that in non-aqueous 1?M LiAsF₆/EC+DMC electrolyte is in the order of 10^?12?cm²?s^?1 during the intercalation/de-intercalation processes. A typical cell LiTi₂ (PO4)₃/5?M LiNO₃/LiNi_1/3Mn_1/3Co_1/3O₂ is constructed and the cycling stability is compared to that with an organic electrolyte.     

LiTFSI as a plastic salt in the quasi-solid state polymer electrolyte for dye-sensitized solar cells

Ionic conductivity and the type of ions are important for the composite polymer electrolyte (CPE) of the dye-sensitized solar cells (DSSCs). Lithium bis(trifluoromethane sulphone)imide (LiTFSI for short) which is easy to dissociate, is added in the composite polymer electrolyte(CPE) as a plasticizer. The LiTFSI acts differently from the conventional LiClO₄. LiTFSI changes the conformation of the polymer chain and shows higher ionic conductivity than LiClO₄. That contributes to the improvement of the short current density of the DSSC. Furthermore, the DSSCs with LiTFSI modification show higher photovoltage than the LiClO₄. The anions of TFSI^? prohibit the interface recombination more effectively compared with the LiClO₄ as the electrochemical impedance spectroscopy indicated. With the LiTFSI modified electrolyte, the performances of the DSSCs under 1 Sun, AM1.5 are improved and reaches the highest of 4.82% at the LiTFSI:LiI = 0.116:1, much better than the original DSSC(3.6%) and the LiClO₄ modified CPE electrolyte DSSC(4.32%).     

Preparation of a novel polymer gel electrolyte based on N-methyl-quinoline iodide and its application in quasi-solid-state dye-sensitized solar cell

Using poly(acrylonitrile-co-styrene) as polymer host, 1,2-propanediol carbonate, dimethyl carbonate and ethylene carbonate as mixture solvent, N-methyl-quinoline iodide and iodine as the source of I⁻/I₃ ⁻, a novel polymer gel electrolyte with ionic conductivity of 5.12 × 10⁻³ S· cm⁻¹ at 25°C was prepared by sol-gel and hydrothermal methods. Based on the polymer gel electrolyte, a quasi-solid-state dye-sensitized solar cell was fabricated. The solar cell possess better long-term stability and light-to-electrical energy conversion efficiency of 4.04% under irradiation of 100 mW· cm⁻². The influences of polymer host, solvent, N-methyl-quinoline iodide and temperature on ionic conductivity of the polymer gel electrolyte and the performance of the dye-sensitized solar cell was discussed.     

The conducting polymer electrolyte based on polypyrrole-polyvinyl alcohol and its application in low-cost quasi-solid-state dye-sensitized solar cells

The effect of polypyrrole (PPy) on the polyvinyl alcohol (PVA)-potassium iodide (KI)-iodine (I₂) polymer electrolytes has been investigated and optimized to use in a dye-sensitized solar cell (DSSC). The different weight ratios of PVA: PPy (93: 2, 91: 4, 89: 6, 87: 8, and 85: 10 wt%) polymer electrolytes (PE) were prepared by solution casting. Structural, complex formation and surface roughness of the prepared electrolytes was confirmed by X-ray diffraction, FTIR, and atomic force microscopy (AFM) respectively. Conductivity plots of all polymer films showed increasing trend with temperature and concentration of PPy. The activation energy of the optimized system found to be 0.871 kJ mol^?1. UV-visible spectrum was adopted to characterize the absorption spectra of the material revealed that increase in the absorbance with increasing PPy content and shifting the absorbance maximum towards lower energy. The indirect band gap decreased from 3.78 to 2.14 eV and direct band gap decreased from 3.88 to 2.71 eV. The EIS analyses revealed the lower charge transfer resistance of 3.029 Ω cm² at the interface between CE and PE. The excellent performance was observed in the fabricated DSSCs using PVA (85%)/PPy (10%)/KI (5%)/I₂ polymer electrolyte with a short-circuit current density of 11.071 mA cm^?2, open-circuit voltage of 0.644 V, fill factor of 0.575, and photovoltaic conversion efficiency of 4.09% under the light intensity of 100 mW cm^?2. Hence, the PPy content in polymer electrolyte influences the remarkable performance of low-cost DSSC.     

Use of A Novel Acetone-H2O2−C10− Chemiluminescence System for the Determination of Iodide Ion

Abstract

The present paper reports a new chemiluminescence system, i.e, acetone-H₂O₂?C10^?, which can be catalyzed by iodide ion (I^?). Based on this catalysis, a new chemiluminescence method for the determination of trace iodide ion is proposed. the optimum conditions are reported in this note. the detection limit is 2 × 10^?11 g/ml I^?, the linear dynamic range is 4 × 10^?10 g/ml to 3 × 10^?7 g/ml I^?, and the variation coefficient at an iodide concentration of 5 × 10^?9 g/ml I^? (n=10) is 4.6%. the method has been satisfactorily applied to the determination of trace iodide ion in water.     

Graphene oxide sheet–polyaniline nanohybrids for enhanced photovoltaic performance of dye‐sensitized solar cells

In this study, photovoltaic (PV) properties of dye‐sensitized solar cells (DSSCs) incorporated with graphene oxide nanosheet‐polyaniline (GOS‐PANI) nanohybrid/poly(ethylene oxide) (PEO) blend gel electrolytes were investigated. Chemical structure and composition of GOS‐PANI nanohybrids were characterized by Raman spectroscopy and X‐ray photoelectron spectroscopy. The images of transmission electron microscopy revealed that PANI nanorods were anchored to the single‐layered GOS for the GOS‐PANI nanohybrids. Ionic conductivities of the GOS‐PANI/PEO–based gel electrolytes were measured using a conductivity meter. The electrochemical catalytic activities of the GOS‐PANI nanohybrids were determined through cyclic voltammetry. These GOS‐PANI nanohybrids were served as the extended electron transfer materials and catalyst for the electrochemical reduction of I₃^?. Due to the enhancement of the ionic conductivity and electrochemical catalytic activity of the gel electrolyte, better PV performance was observed for the DSSCs based on the GOS‐PANI containing electrolytes as compared to the pristine PEO electrolyte‐based DSSC sample. Moreover, PV performances of the GOS‐PANI/PEO–based DSSCs were closely related to the PANI content of GOS‐PANI nanohybrids. The highest photo‐energy conversion efficiency (5.63%) was obtained for an optimized GOS‐PANI/PEO (5:95, w/w) blend gel electrolyte‐based DSSC sample. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 321–332     

A novel gel polymer electrolyte based on poly ionic liquid 1-ethyl 3-(2-methacryloyloxy ethyl) imidazolium iodide

Poly ionic liquid 1-ethyl 3-(2-methacryloyloxy ethyl) imidazolium iodide (PEMEImI) as a single-ion conductor was designed and synthesized. When appropriate amount of suitable plasticizers, I₂ and polyacrylonitrile (PAN) were incorporated into it, the complex formed gel polymer electrolyte. Chemical structure, thermal behavior and ionic conductive properties of the gel polymer electrolyte were investigated by Raman spectra, UV-Vis spectra, differential scanning calorimetry (DSC), and complex impedance analysis, respectively. For the new gel polymer electrolyte, the ionic conductivity of about 1 × 10⁻³ S cm⁻¹ at room temperature was achieved.     

Upon the existence of [Al3Cl10]− in room temperature chloroaluminate ionic liquids

A negative-ion fast-atom-bombardment mass spectrometric study of the room temperature chloroaluminate ionic liquids AlCl₃-[MeEtim]Cl ([MeEtim]⁺ = 1-methyl-3-ethylimidazolium cation) has produced the first unambiguous experimental evidence for the existence of [Al₃C1₁₀]^?.     

Highly Catalytic Carbon Nanotube/Pt Nanohybrid‐Based Transparent Counter Electrode for Efficient Dye‐Sensitized Solar Cells

Low‐cost transparent counter electrodes (CEs) for efficient dye‐sensitized solar cells (DSSCs) are prepared by using nanohybrids of carbon nanotube (CNT)‐supported platinum nanoparticles as highly active catalysts. The nanohybrids, synthesized by an ionic‐liquid‐assisted sonochemical method, are directly deposited on either rigid glass or flexible plastic substrates by a facile electrospray method for operation as CEs. Their electrochemical performances are examined by cyclic voltammetry, current density–voltage characteristics, and electrochemical impedance spectroscopy (EIS) measurements. The CNT/Pt hybrid films exhibit high electrocatalytic activity for I^?/I₃^? with a weak dependence on film thickness. A transparent CNT/Pt hybrid CE film about 100 nm thick with a transparency of about 70 % (at 550 nm) can result in a high power conversion efficiency (η) of over 8.5 %, which is comparable to that of pyrolysis platinum‐based DSSCs, but lower cost. Furthermore, DSSC based on flexible CNT/Pt hybrid CE using indium‐doped tin oxide‐coated polyethylene terephthalate as the substrate also exhibits η=8.43 % with J_sc=16.85 mA cm^?2, V_oc=780 mV, and FF=0.64, and this shows great potential in developing highly efficient flexible DSSCs.