Ca2＋交换的几种分子筛的氮氩分离性能

采用水溶液离子交换法制备了Ca2＋交换的4A、13X和LSX分子筛，并在25 ℃下测定了它们的静态吸附等温线和动态穿透曲线.研究发现， Ca2＋交换的4A、13X和LSX分子筛对氮的吸附性能都明显优于其相应的钠型分子筛，而它们对氩的吸附量变化不大，说明Ca2＋交换的这三种分子筛是较好的氮氩分离吸附剂.从动态吸附的结果来看，所研究的各种分子筛都有一个最优的吸附分离压力，在本论文研究的压力范围内，这个最优压力在0.6 MPa附近.由穿透曲线可推算出混合气体的吸附量，通过氮和氩在混合气体中的吸附量和相应纯气体吸附量的对比可以得出，对于氮氩吸附选择性较高的分子筛，氮的存在对氩的吸附量有较大的影响.     

Li＋交换的几种分子筛的氮氩分离性能

采用水溶液离子交换法制备了高Li＋交换度的4A、13X和LSX分子筛,并在25 ℃下测定了它们的静态吸附等温线和动态穿透曲线.研究发现,高Li＋离子交换度的4A、13X和LSX分子筛都具有较大的氮吸附容量和较高的氮氩分离选择性,说明高Li＋离子交换度的4A、13X和LSX分子筛是较好的氮氩分离吸附剂.从动态穿透曲线结果来看,所研究的三种分子筛都有一个最优的吸附分离压力,在本文研究的压力范围内,这个最优压力在0.6 MPa附近.对比高锂交换度的三种分子筛,以高锂交换度的LSX分子筛的氮氩吸附分离性能最好.     

不同分子筛的氮氩分离性能

采用水溶液离子交换法制备了不同离子交换的13X和4A分子筛,并在25℃下测 定了它们的静态吸附等温线和动态穿透曲线。研究发现,Ca~(2+)离子和Li~+离子 交换的13X和4A分子筛对氮的吸附性能都明显优于其相应的钠型分子筛,而它们对 氩的吸附量变化不大,说明这两种离子交换的分子筛是较好的氮氩分离吸附剂。从 动态吸附的结果来看,所研究的各种分子筛都有一个最优的吸附分离压力,在本论 文研究的压力范围内,这个最优压力在0.6MPa附近。通过穿透曲线推算出的混合气 体吸附量和纯气体吸附量的对比可以得出,对于氮氩吸附选择性较高的分子筛,氮 的存在对氩的吸附量有较大的影响。     

N2和Ar在改性的NaA分子筛上的吸附分离

采用水溶液离子交换法分别制备了不同Li^ 和Ca^2^ 交换度的A型分子筛,并在25℃下测定了各分子筛吸附剂的氮和氩的吸附等温线及穿透曲线．研究发现,锂交换和钙交换的两种分子筛的氮吸附量和氮氩分离选择性都随分子筛中阳离子交换度的增加而增大;在阳离子交换度较高时,锂离子和钙离子交换的A型分子筛的氮氩分离能力均优于NaA分子筛．穿透曲线的结果显示,所研究的各种吸附剂都存在一个最优的吸附分离压力,大约在0．6MPa．在0．6MPaT,接近100％阳离子交换度的CaNaA分子筛的动态氮氩分离性能优于相同交换度的LiNaA分子筛。     

几种二价阳离子的交换对13X分子筛氮氩分离性能的影响

采用水溶液离子交换法分别制备了不同二价阳离子(Mg²⁺、Zn²⁺和Ca²⁺)交换的13X型分子筛，并在25 ℃下测定了各分子筛吸附剂的氮和氩的吸附等温线。研究发现，13X分子筛经Mg²⁺和Zn²⁺交换后，吸附剂的吸氮能力及氮氩分离能力降低；13X分子筛经Ca²⁺交换后，吸附剂的吸氮能力及氮氩分离能力随分子筛中钙离子交换度的增加而增大。对常压氮氩分离性能较好的CaNaX系列分子     

氮、氩在5A^。分子筛上的低温吸附分离

测定了不同温度下氮、氩在5分子筛上的吸附等温线,其中三参数的Langmuir-Freundlich方程和Toth方程在不同温度下都能获得较好的拟合结果;计算了不同温度下氮、氩在5分子筛上吸附的亨利常数,获得了氮、氩选择性和温度的关系.测定了125K温度下氮、氩混合气体在5分子筛吸附柱上的穿透曲线.结果表明:最先流出的5L气体中含有约70%的氩,通过收集5L气体即可实现混合气体中氩的初步分离.     

氮、氩在5分子筛上的低温吸附分离

测定了不同温度下氮、氩在5分子筛上的吸附等温线,其中三参数的Langmuir-Freundlich方程和Toth方程在不同温度下都能获得较好的拟合结果;计算了不同温度下氮、氩在5分子筛上吸附的亨利常数,获得了氮、氩选择性和温度的关系。测定了125K温度下氮、氩混合气体在5分子筛吸附柱上的穿透曲线。结果表明:最先流出的5L气体中含有约70%的氩,通过收集5L气体即可实现混合气体中氩的初步分离。     

低温变压分子筛动态分离CH_4/CO_2实验研究

在低温变压条件下测量了5A和13X沸石分子筛对CH_4/CO_2混合气体的分离能力。实验研究了CH_4/CO_2气体流量、吸附压力、填料高度和吸附温度对穿透曲线和分离能力的影响。研究结果表明,增大气体流量、增加吸附压力会降低分离效果,减小混合气体的分离系数;降低吸附温度、增加填料高度有利于CH_4/CO_2分离,提高混合气体的分离系数;在相同实验条件下,13X沸石分子筛对CH_4/CO_2混合气体吸附分离能力高于5A分子筛。     

13X分子筛去除水中重金属离子的研究

以人工合成的13X型分子筛为吸附剂,研究了水中Pb2 、Cd2 和Cu2 在分子筛上的吸附行为,讨论了Pb2 、Cd2 和Cu2 共存条件下的竞争吸附,并考察了水中存在的Na 、Mg2 、Ca2 等离子对分子筛吸附去除重金属的影响.实验结果表明,13X分子筛对Pb2 、Cd2 和Cu2 3种离子的吸附符合Langmuir模型,最大吸附量分别为2.47mmol/L、2.0mmol/L和1.78mmol/L.在竞争吸附条件下,13X分子筛对3种重金属离子的选择性依次为pb2 ＞Cd2 ＞Cu2 .水中存在的Na 、Mg2 、Ca2 等对分子筛吸附重金属效率有一定的影响,其中Ca2 对Cu2 在分子筛上的去除影响最为显著.     

晶种法高效合成低硅铝比LSX型分子筛

分别以工业级的偏铝酸钠和水玻璃为铝源和硅源,氢氧化钠为主要碱源,氢氧化钾为辅助碱源,采用LSX晶种法制备了LSX型分子筛。通过X射线衍射(XRD)、扫描电子显微镜(SEM)、X射线荧光(XRF)、傅里叶变换红外光谱(FTIR)和N2吸附-脱附等表征方式考察了有无晶种、钾钠物质的量之比、晶化条件对合成LSX型分子筛的影响。结果表明,加入LSX晶种不仅能显著缩短晶化时间,提高分子筛的结晶度,还可有效抑制方钠石和A型杂晶的伴生;钾钠比过高或过低均会造成A型或方钠石型杂晶的伴生;直接进行高温晶化会导致亚稳态的LSX型分子筛向热力学稳定相转变;延长老化时间或高温晶化处理降低了产物中的硅铝比;样品的比表面积和N2吸附量随老化时间的延长和高温晶化处理而逐渐下降。     

Sc2MgGa2 and Y2MgGa2

Scandium magnesium gallide, Sc₂MgGa₂, and yttrium magnesium gallide, Y₂MgGa₂, were synthesized from the corresponding elements by heating under an argon atmosphere in an induction furnace. These intermetallic compounds crystallize in the tetragonal Mo₂FeB₂‐type structure. All three crystallographically unique atoms occupy special positions and the site symmetries of (Sc/Y, Ga) and Mg are m2m and 4/m, respectively. The coordinations around Sc/Y, Mg and Ga are pentagonal (Sc/Y), tetragonal (Mg) and triangular (Ga) prisms, with four (Mg) or three (Ga) additional capping atoms leading to the coordination numbers [10], [8+4] and [6+3], respectively. The crystal structure of Sc₂MgGa₂ was determined from single‐crystal diffraction intensities and the isostructural Y₂MgGa₂ was identified from powder diffraction data.     

Electrochemical study of (NEt4)2Cl2FeS2MoS2 and (NEt4)2Cl2FeS2MoS2FeCl2

Summary The ability of [MoS₄]^2–, anions to be used as ligands for transition metal ions has been widely demonstrated, especially with Fe²⁺. The present study has been restricted to linear complexes such as (NEt₄)₂ [Cl₂FeS₂MoS₂] and (NEt₄)₂[Cl₂FeS₂MoS₂FeCl₂]. Their electrochemical properties are described: upon electrochemical reduction, these compounds yield MoS₂, as a black precipitate, and an iron complex in solution, assumed to be [SFeCl₂]^2–. The electrochemical reduction goes through two electron transfers, coupled with the breakdown of the molecular skeleton: a DISPl and an ECE mechanism. Depending on the solvent, the following equilibrium may be observed: [Cl₄Fe₂MoS₄]^2–[Cl₂FeMoS₄]^2–+FeCl₂. The equilibrium constant, K_D, was evaluated by differential pulse polarography. K_D is tightly related to the donor number of the solvent.     

Zur Kenntnis der Dialkalimetalldichalkogenide β-Na2S2, K2S2, α-Rb2S2, β-Rb2S2, K2Se2, Rb2Se2, α-K2Te2, β-K2Te2 und Rb2Te2

On Dialkali Metal Dichalcogenides β-Na₂S₂, K₂S₂, α-Rb₂S₂, β-Rb₂S₂, K₂Se₂, Rb₂Se₂, α-K₂Te₂, β-K₂Te₂ and Rb₂Te₂ The first presentation of pure samples of α- and β-Rb₂S₂, α- and β-K₂Te₂, and Rb₂Te₂ is described. Using single crystals of K₂S₂ and K₂Se₂, received by ammonothermal synthesis, the structure of the Na₂O₂ type and by using single crystals of β-Na₂S₂ and β-K₂Te₂ the Li₂O₂ type structure will be refined. By combined investigations with temperature-dependent Guinier-, neutron diffraction-, thermal analysis, and Raman-spectroscopy the nature of the monotropic phase transition from the Na₂O₂ type to the Li₂O₂ type will be explained by means of the examples α-/β-Na₂S₂ and α-/β-K₂Te₂. A further case of dimorphic condition as well as the monotropic phase transition of α- and β-Rb₂S₂ is presented. The existing areas of the structure fields of the dialkali metal dichalcogenides are limited by the model of the polar covalence.     

The alkali hypophosphites KH2PO2, RbH2PO2 and CsH2PO2

The structures of the hypophosphites KH₂PO₂ (potassium hypophosphite), RbH₂PO₂ (rubidium hypophosphite) and CsH₂PO₂ (caesium hypophosphite) have been determined by single‐crystal X‐ray diffraction. The structures consist of layers of alkali cations and hypophosphite anions, with the latter bridging four cations within the same layer. The Rb and Cs hypophosphites are isomorphous.     

Formal [(2+2)+2] and [(2+2)+(2+2)] nonconjugated dienediyne cascade cycloadditions

[reaction: see text] Fluoranthene 2 and heptacycle 3 are easily accessible from the reaction of diyne 1 and norbornadiene (NBD) in the presence of the rhodium catalyst. The unusual [(2+2)+(2+2)] adduct 3 was confirmed by the X-ray crystal structure analysis.     

Crystal Structures of [Bu2Sn(O2PPh2)2], [Ph2Sn(O2PPh2)2], and [PhClSn(O2PPh2)OMe]2. Raman Spectra of [Ph2Sn(O2PPh2)2] and [PhClSn(O2PPh2)OMe]2

[(n‐Bu)₂Sn(O₂PPh₂)₂] ( 1 ), and [Ph₂Sn(O₂PPh₂)₂] ( 2 ) have been synthesized by the reactions of R₂SnCl₂ (R=n‐Bu, Ph) with HO₂PPh₂ in Methanol. From the reaction of Ph₂SnCl₂ with diphenylphosphinic acid a third product [PhClSn(O₂PPh₂)OMe]₂ ( 3 ) could be isolated. X‐ray diffraction studies show 1 to crystallize in the monoclinic space group P2₁/c with a = 1303.7(1) pm, b = 2286.9(2) pm, c = 1063.1(1) pm, β = 94.383(6)°, and Z = 4. 2 crystallizes triclinic in the space group , the cell parameters being a = 1293.2(2) pm, b = 1478.5(4) pm, c = 1507.2(3) pm, α = 98.86(3)°, β = 109.63(2)°, γ = 114.88(2)°, and Z = 2. Both compounds form arrays of eight‐membered rings (SnOPO)₂ linked at the tin atoms to form chains of infinite length. The dimer 3 consists of a like ring, in which the tin atoms are bridged by methoxo groups. It crystallizes triclinic in space group with a = 946.4(1) pm, b = 963.7(1) pm, c = 1174.2(1) pm, α = 82.495(6)°, β = 66.451(6)°, γ = 74.922(6)°, and Z = 1 for the dimer. The Raman spectra of 2 and 3 are given and discussed.     

Die Photoionenspektren von SCl2, S2Cl2 und S2Br2

Photoionization Mass Spectra of SCl₂, S₂Cl₂, and S₂Br₂ Photoionization mass spectra of SCl₂, S₂Cl₂, and S₂Br₂ have been measured. Heats of formation, bond energies, and ionization potentials of fragments have been calculated from appearance potentials.