Simultaneous Determination of Cadmium,Lead, Copper and Mercury Ions Using Organofunctionalized SBA‐15 Nanostructured Silica Modified Graphite–Polyurethane Composite Electrode

A new sensor has been developed for the simultaneous detection of cadmium, lead, copper and mercury, using differential pulse and square wave anodic stripping voltammetry (DPASV and SWASV) at a graphite–polyurethane composite electrode with SBA‐15 silica organofunctionalized with 2‐benzothiazolethiol as bulk modifier. The heavy metal ions were preconcentrated on the surface of the modified electrode at ?1.1 V vs. SCE where they complex with 2‐benzothiazolethiol and are reduced to the metals, and are then reoxidized. Optimum SWASV conditions lead to nanomolar detection limits and simultaneous determination of Cd²⁺, Pb²⁺, Cu²⁺ and Hg²⁺ in natural waters was achieved.     

Simultaneous Voltammetric Determination of Zn,Cd and Pb at Bismuth Nanopowder Electrodes with Various Particle Size Distributions

Effect of particle size distribution on sensor characteristics of nano‐Bi fixed electrode has been investigated using square wave anodic stripping voltammetry. Bi nanopowders with various particle size distributions were synthesized by gas condensation (GC) method with the change of chamber pressure. As the chamber pressure decreased, the size of Bi nanopowder became smaller with narrower distribution due to a shorter residence time of Bi vapor. The square wave anodic stripping voltammograms (SWASV) showed well‐defined and highly reproducible peaks at ?1.2 V, ?0.8 V and ?0.6 V (vs. SCE), which are closely related to the oxidation of Zn, Cd and Pb, respectively. The sensitivity and detection limit of the nano‐Bi fixed electrode were quantitatively estimated from the analyses of SWASV. From the results, it is concluded that as the size of Bi nanopowder becomes smaller with narrower particle size distribution, the sensitivity and detection limit of sensor electrode for Zn, Cd and Pb are improved, which is ascribed to the increase in electrochemical‐active surface area.     

Quantitation of Metal Ions in Archaeological Glass by Abrasive Stripping Square‐Wave Voltammetry Using Graphite/Polyester Composite Electrodes

A method for identifying Co, Cu, Sb, Sn, Fe, Zn, and Zr pigments in glasses using square‐wave voltammetry as the detection mode is described. It is based on the abrasive attachment of glass microsamples to graphite/polyester composite electrodes. Sample amounts less than 1 μg are used allowing for the study of archaeological samples. In all cases well‐defined anodic stripping peaks corresponding to the oxidation of metal deposits generated at potentials ranging from ?0.6 to ?1.6 V (vs. SCE) are obtained. This response is in agreement with that displayed by the corresponding metal oxides. Quantitative estimates of the relative population of metal ions in glasses are obtained from peak area measurements with an accuracy comparable to that obtained with SEM/EDX.     

Sensitive Voltammetric Determination of Cadmium(II) with 8‐Hydroxyquinoline and Ionic Liquid Modified Carbon Paste Electrode

In this paper 8‐hydroxyquinoline (HQ) and ionic liquid (IL) modified carbon paste electrode was fabricated and used for the sensitive determination of cadmium(II) with differential pulse anodic stripping voltammetry (DPASV). The modified electrode was prepared by the addition of HQ and IL 1‐ethyl‐3‐methylimidazoliam ethylsulphate as the modifiers into the traditional carbon paste mixture. Cd(II) was preconcentrated and reduced on the surface of the modified electrode at the potential of ‐1.0 V (vs. SCE) by the co‐contributions from the formation of HQ‐Cd(II) complex and the accumulation effect of IL. Then the reduced Cd on the electrode surface was reoxidized by DPASV with a sensitive oxidation peak appeared at ‐0.79 V (vs. SCE). Under the optimal conditions the oxidation peak current was proportional to the Cd(II) concentration in the range from 0.03 to 2.0 mol/L with the detection limit as 5.0 nmol/L (3σ). The proposed method was successfully applied to the water samples detection with the recovery in the range from 95.6% to 96.6%.     

Electrochemical Impedance Characterization of Nafion‐Coated Carbon Film Resistor Electrodes for Electroanalysis

Carbon film disk electrodes with Nafion coatings have been characterized by electrochemical impedance spectroscopy (EIS) with a view to a better understanding of their advantages and limitations in electroanalysis, particularly in anodic stripping voltammetry of metal ions. After initial examination by cyclic voltammetry, spectra were recorded over the full potential range in acetate buffer solution at the bare electrodes, electrodes electrochemically pretreated in acid solution, and Nafion‐coated pretreated electrodes in the presence and absence of dissolved oxygen. EIS equivalent circuit analysis clearly demonstrated the changes between these electrode assemblies. In order to simulate anodic stripping voltammetry conditions, spectra were also obtained in the presence of cadmium and lead ions in solution at Nafion‐coated electrodes, both after metal ion deposition and following re‐oxidation. Permanent changes to the structure of the Nafion film occurred, which has implications for use of these electrode assemblies in anodic stripping voltammetry at relatively high trace metal ion concentrations.     

Renewable Pencil Electrodes for Highly Sensitive Anodic Stripping Voltammetric Determination of 3‐Hydroxyflavone and Morin in Bulk Form and in Biological Fluids

An electrochemical anodic adsorptive stripping procedure for ultra‐trace assay of 3‐hydroxyflavone (3HF) and Morin at a renewable pencil electrode (PGE) in bulk form and in biological fluids is described. The nature of the oxidation process of 3HF and Morin taking place at the PGE was characterized by cyclic voltammetry. The results show that the determination of the oxidation peak current is the basis of a simple, accurate and rapid method for quantification of 3HF by square‐wave anodic stripping voltammetry. Determination of Morin was achieved by square‐wave anodic adsorptive stripping voltammetry of the formed Morin? Cu(II) complex at a PGE. Factors influencing the trace measurements of 3HF and the Morin? Cu (II) complex at a PGE are assessed. The limits of detection and quantitation for the determination of 3HF and Morin in bulk form and in biological fluids were determined. The statistical analysis and the calibration curve data for trace determination of 3HF and Morin are reported.     

辛可宁修饰碳糊电极的应用研究——铋的阳极溶出伏安法测定

报道了利用辛可宁修饰碳糊电极测定铋的方法,在1mol/LH2SO4溶液中,通过在－1.00V电位下富集Bi3＋后,在－0.20～＋0.15V电位范围内作阳极溶出伏安法测定。在－0.022V处有一灵敏的氧化峰,峰电流与Bi     

Intermetallic compounds and the determination of copper and zinc by anodic stripping voltammetry

The intermetallic CuZn compounds produced during the simultaneous deposition of copper and zinc at a preformed mercury film electrode were studied. Over a wide range of metal concentration ratios, the real concentrations of metals in the amalgam were calculated from the peak areas obtained by anodic stripping voltammetry. The results indicate the formation of CuZn (insoluble) and CuZn2 (soluble) compounds with K_so=5×10^?4 and β₂=100, respectively. The electrodeposition potential of ?0.85 V vs. SCE for the reduction of copper in presence of zinc is confirmed as correct.     

A new method for the voltammetric determination of molybdenum(VI) using carbon paste electrodes modified in situ with cetyltrimethylammonium bromide

Molybdenum(VI) is determined by anodic stripping voltammetry using a carbon paste electrode modified in situ with cetyltrimethylammonium bromide (CTAB). The preconcentration of molybdenum is performed by adsorption and reduction of ion-pairs of cetyltrimethylammonium and molybdenum(VI) oxalate at a potential of −0.4 V vs. the saturated calomel electrode (SCE). The supporting electrolyte contains 0.01 M oxalic acid and 0.075 mM CTAB. Differential pulse anodic stripping voltammetry exploiting the reoxidation signal is used for the determination of trace levels of molybdenum(VI). Linearity between current and concentration exists for a range of 0.5–500 μg 1⁻¹ Mo with proper preconcentration times; the limit of detection (calculated as 3σ) is 0.04 μg 1⁻¹ with an accumulation period of 10 min.     

痕量铅在草酸修饰电极上阳极溶出伏安的研究

本文对草酸修饰电极的制作、痕量铅在草酸修饰电极上的反应机理和电化学特性作了研究。采用阳极溶出伏安法,测定铅的灵敏度比玻碳电极提高7.5倍,在1.0～15.0ng·/mL铅浓度范围内溶出峰高与铅浓度呈良好的线性关系。连续测定12次变异系数为3.0％。利用草酸修饰电极对人尿中痕量铅进行了测定,结果良好。     

Electrochemistry of triphenyltin acetate at a mercury-film glassy carbon electrode

The electrochemical behaviour of triphenyltin acetate was investigated by cyclic voltammetry, differential-pulse voltammetry and controlled potential electrolysis at a mercury-film glassy carbon electrode. Effects on the electrochemical response of the composition of supporting electrolytes, pH, electrode rotation speed and triphenyltin acetate concentration were determined. The electrochemical reduction of this compound was found to involve a preliminary adsorption process (E_peak ≈ ?0.7 V vs. SCE), the reduction of triphenyltin acetate to the triphenyltin radical (E_peak ≈ ?1.0 V) and reduction of the radical to the triphenyltin anion (E_peak ≈ ?1.4 V). A procedure for the determination of trace amounts of this compound by differential-pulse anodic stripping voltammetry in 50% (v/v) ethanol with 0.1 M acetic acid + 0.1 M ammonia solution was developed and applied to the analysis of a commercial powder formulation and water and fish samples. The limit of detection was 2.5 × 10^?9 M triphenyltin acetate.     

聚氯乙烯膜修饰碳微电极的研制及应用

采用浸涂流延法制得ＰＶＣ膜修饰碳微电极,用Ｋ３Ｆｅ（ＣＮ）６的循环伏安图考察了电极的电化学性能,并用此电极建立了环境水样中痕量汞的阳极溶出伏安法测定。在０．０６ｍｏｌ／Ｌ ＫＳＣＮ＋０．０１ｍｏｌ／ＬＫＣｌ介质中,富集电位－０．８０Ｖ,搅拌富集时间３００ｓ,扫描电压范围－０．２０～０．４０Ｖ,扫描速率３１４ｍＶ／ｓ,咄峰电流与Ｈｇ＾２＋浓度在０．０１～２．０ｍｇ／Ｌ的范围内有良好的线性关系,本电极     

Bucky-gel coated glassy carbon electrodes, for voltammetric detection of femtomolar leveled lead ions

Femtomolar (fM) leveled lead ions were electrochemically detected using a bucky-gel coated glassy carbon electrode and differential pulse anodic stripping voltammetry. The bucky-gel was composed of dithizone, ionic liquid (1-butyl-3-methylimidazolium hexafluorophosphate), and multi-walled carbon nanotubes (MWCNTs). The fabrication of the bucky-gel coated electrode was optimized. The modified electrode was characterized with voltammetry, electrochemical impedance spectroscopy, and chronoamperometry. After the accumulation of lead ions into the bucky-gel modified electrode at −1.2 V vs. saturated calomel electrode (SCE) for 5 min in a pH 4.4 sodium acetate-acetate acid buffer solution, differential pulse anodic stripping voltammograms of the accumulated lead show an anodic wave at −0.58 V. The anodic peak current is detectable for lead ions in the concentration range from 1.0 μM down to 500 fM. The detection limit is calculated to be 100 fM. The proposed method was successfully applied for the detection of lead ions in lake water.     

Stripping voltammetry for the determination of trace metal speciation and in-situ measurements of trace metal distributions in marine waters

Progress in marine chemistry has been driven by improved sampling and sample handling techniques, and developments in analytical chemistry. Consequently, during the last 20 years our understanding of marine trace metal biogeochemistry has improved a great deal. Stripping voltammetric techniques (anodic stripping voltammetry and adsorptive cathodic stripping voltammetry) have made an important contribution to this understanding. The selectivity and extremely low detection limits have made stripping voltammetry a widely used technique for trace metal speciation and trace metal distribution measurements in seawater. Stripping voltammetry is very suitable for ship-board and in-situ applications because of the portability, low cost and capability for automation of the voltammetric instrumentation. Future developments in stripping voltammetry can be expected in the field of stand-alone submersible voltammetric analysers, capable of continuous trace metal measurements. Future applications of stripping voltammetry can be found in the interactions between trace metal speciation and growth and the functioning of organisms in pristine and metal polluted marine waters.     

Nafion‐Modified Glassy Carbon Electrode for Trace Determination of Indium

Abstract

A new method for determination of trace indium is proposed by the adsorption stripping voltammetry (ASV) using a Nafion‐modified glassy carbon electrode (NMGCE). This chemically modified electrode (CME) shows a better stability. A sensitive oxidation peak was observed, and the anodic peak potential is ca. ?0.548 V (vs. SCE). The influences of various experimental parameters on the current peak were completely studied. Under the optimized condition, the method has been applied to the determination of indium in water samples. There is a good linear relationship between the peak current (i_p) and indium(III) concentration in the range of 1.0×10^?9–1.0×10^?7 mol/l, and the limit of detection is 7.5×10^?10 mol/l.     

Voltammetric Study of Aminopurines on Pencil Graphite Electrode in the Presence of Copper Ions

Electrochemical oxidations of aminopurines (adenine, 2‐aminopurine, 2,6‐diaminopurine) and their complexes with Cu(I) on a pencil graphite electrode were investigated by means of linear sweep voltammetry (LSV) and elimination voltammetry with linear scan (EVLS). The anodic process of the Cu(I)‐aminopurine complex, corresponding to the oxidation of Cu(I) to Cu(II), takes place in the potential range between 0.4 and 0.5 V (vs. Ag/AgCl/3 M KCl). At more positive potentials the aminopurines provide voltammetric peaks resulting from the oxidation of the purine ring. The stability of the accumulated complex layer was investigated by the adsorptive transfer stripping technique.     

Anodic behaviour of the (222) macrobicyclic ligand on mercury electrode in propylenecarbonate

The anodic behaviour of the free macrobicyclic ligand (222) was examined by various electrochemical techniques on mercury and on platinum electrodes. From results on platinum electrode using cyclic voltammetry it appears that the anodic oxidation of (222) proceeds irreversibly at potentials more positive than +0.7 V (aq. SCE), however, its mechanism could not be determined because the anodic signal was not well developed. Under polarographic conditions a reversible anodic diffusion controlled wave at E_1/2=+0.08 V (aq. SCE) was observed, corresponding to a complex formation of the ligand (222) with the ions of mercury formed by anodic polarization of mercury electrode. In excess of mercuric cations a cathodic wave at slightly more positive potentals was found.     

Influence of Nafion Coatings and Surfactant on the Stripping Voltammetry of Heavy Metals at Bismuth‐Film Modified Carbon Film Electrodes

Nafion polymer coated bismuth‐film‐modified carbon film electrodes have been investigated for reducing the influence of contaminants such as surfactants in the anodic stripping voltammetry of trace metal ions. The influence of the coating on electrode response has been tested with both ex situ and in situ bismuth film deposition, with and without the polymer coating. The electrode assemblies and interfacial characteristics in the presence of the non‐ionic surfactant Triton‐X‐100 have been probed with electrochemical impedance spectroscopy. The Nafion coating successfully decreases the adsorption of Triton on the bismuth film surface, and demonstrates that this strategy allows measurement of these trace metals in environmental samples containing surfactants.     

Sb在Au电极上不可逆吸附的电化学过程

用电化学循环伏安法和电化学石英晶体微天平(EQCM)技术研究了Sb在Au电极上不可逆吸附的电化学过程. 研究结果表明, 在-0.25 V到0.18 V(vs SCE)范围内, Sb可在Au电极上稳定吸附, 并且在0.15 V附近出现特征氧化还原峰. 根据EQCM实验数据, 在电位0.18 V时, Sb在Au电极上的氧化产物是Sb2O3; 同时Sb的吸附阻止了电解液中阴离子和水在Au电极上的吸附. 当电极电位超过0.20 V时, Sb2O3会被进一步氧化成Sb5+化合物, 同时逐渐从Au电极表面脱附.     

Electrode Modified with Langmuir–Blodgett (LB) Film of Calixarenes for Preconcentration and Stripping Analysis of Hg(II)

A new type of current sensor, Langmuir–Blodgett (LB) film of calixarene on the surface of glassy carbon electrode (GCE) was prepared for determination of mercury by anodic stripping voltammetry (ASV). An anodic stripping peak was obtained at 0.15 V (vs. SCE) by scanning the potential from ?0.6 to +0.6 V. Compared with a bare GCE, the LB film coated electrode greatly improves the sensitivity of measuring mercury ion. The fabricated electrode in a 0.1 M H₂SO₄+0.01 M HCl solution shows a linear voltammetric response in the range of 0.07–40 μg L^?1 and detection limit of 0.04 μg L^?1 (ca. 2×10^?10 M). The high sensitivity, selectivity, and stability of this LB film modified electrode demonstrates its practical application for a simple, rapid and economical determination of Hg²⁺ in a water sample.