Determination of Selenium Traces on Cyclic Renewable Mercury Film Silver Electrode in Presence of Copper Ions Using Cathodic Stripping Voltammetry

The new cyclic renewable mercury film silver based electrode (Hg(Ag)FE), applied for the determination of selenium(IV) traces in the presence of copper ions using differential pulse cathodic stripping voltammetry (DP CSV) is presented. The preparation of the Hg(Ag)FE is very simple. The effects of various factors such as: preconcentration potential and time, pulse height, step potential and supporting electrolyte composition are optimized. The calibration graph is linear from 0.5 nM (39 ng L^?1) to 100 nM (7.9 μg L^?1) for a preconcentration time of 45 s, with correlation coefficient of 0.9995. For a Hg(Ag)FE with a surface area of 8 mm² the detection limit for a preconcentration time of 90 s is as low as 17 ng L^?1. The repeatability of the method at a concentration level of the analyte as low as 2 μg L^?1, expressed as RSD is 2.7% (n=7). The proposed method was successfully applied and validated by studying the certified reference material (bovine liver BCR‐185) and simultaneously recovery of Se(IV) from spiked water samples.     

Renewable Copper and Silver Amalgam Film Electrodes of Prolonged Application for the Determination of Elemental Sulfur Using Stripping Voltammetry

New, renewable copper (Hg(Cu)FE) and silver (Hg(Ag)FE) based amalgam film electrodes applied for the determination of elemental sulfur using differential pulse cathodic stripping voltammetry are presented. With surface areas adjustable from 1 to 12 mm², both electrodes are characterized by very good surface reproducibility (≤2%) and long‐term stability (a few thousand measurement cycles). The mechanical refreshing of the amalgam film takes about 1–2 seconds. The effects of various factors such as instrumental parameters and the supporting electrolyte composition were optimized. Interferences from sulfides are easily removed by the addition of acid, and bubbling with argon, for Hg(Ag)FE. In the case of Hg(Cu)FE, sulfides did not interfere. The calibration graph is linear within the studied range from 16 ng L^?1 to 4.8 μg L^?1 for Hg(Cu)FE, and up to 6.4 μg L^?1 for Hg(Ag)FE (t_acc=15 s). The correlation coefficients for the two electrodes were at least 0.997. The detection limits for a low concentration of S(0) and t_acc=60 s are as low as 14 ng L^?1 for Hg(Cu)FE and 4 ng L^?1 for Hg(Ag)FE. The proposed method was successfully applied and validated by studying the recovery of S(0) from spiked river water.     

Novel Sensitive Voltammetric Detection of Trace Gallium(III) with Presence of Catechol Using Mercury Film Silver Based Electrode

A new adsorptive stripping voltammetric method for the determination of trace gallium(III) based on the adsorption of gallium(III)‐catechol complex on the cyclic renewable mercury film silver based electrode (Hg(Ag)FE) is presented. The effects of various factors such as: preconcentration potential and time, pulse height, step potential and supporting electrolyte composition are optimized. The calibration graph is linear from 2 nM (0.14 μg L^?1) to 100 nM (6.97 μg L^?1) for a preconcentration time of 30 s, with correlation coefficient of 0.9993. For a Hg(Ag)FE with a surface area of 9.7 mm² the detection limit for a preconcentration time of 90 s is as low as 7 ng L^?1. The repeatability of the method at a concentration level of the analyte as low as 0.05 μg L^?1, expressed as RSD is 3.6% (n=5). The proposed method was successfully applied by studying the natural samples and simultaneous recovery of Ga(III) from spiked water and sediment samples.     

Novel Screen-Printed Gold Nano Film Electrode for Trace Mercury(II) Determination Using Anodic Stripping Voltammetry

Integrating the screen printing technique with the vacuum evaporation method, we developed a novel and disposable screen-printed gold film electrode (SPGFE) in the present work. First, a conductive silver layer, a connection graphite-carbon layer, and an insulating polymer layer were successively printed onto a flexible polyethylene terephthalate (PET) substrate. Then, a gold thin film was achieved on the scheduled vacant site by use of the vacuum evaporation method. In order to enhance the electroanalytical performance of the SPGFE, the thickness of the gold film was controlled in the range of 70–80 nm under optimum conditions. The fabricated SPGFE was applied to detect trace mercury(II) based on the square-wave anodic stripping voltammetry (SWASV). The results indicated that the proposed SPGFE exhibited higher sensitivity to trace mercury(II) than the gold disc electrode. The stripping current was linearly related to the concentration of mercury(II) in the range of 16–280 µg/L (R² = 0.9919) and 1.2–8.0 µg/L (R² = 0.9977), with a detection limit of 0.8 µg/L (S/N = 3) under 180 s accumulation. The SPGFE was further used to detect mercury in real samples, and the obtained results revealed a good agreement with those of inductively coupled plasma atomic emission spectrometry (ICP-AES) and atomic absorption spectroscopy (AAS). The highly sensitive and environmental friendly electrode, as another type of “mercury-free” electrode, holds great promise in stripping measurements.     

Adsorptive Stripping Determination of Scandium(III) with Mordant Blue 9 on Silver Amalgam Film Electrode

A new adsorptive stripping voltammetric method for the determination of trace scandium(III) based on the adsorption of scandium(III)‐mordant blue 9 complex on the cyclic renewable mercury film silver based electrode (Hg(Ag)FE) is presented. The effects of various factors such as: preconcentration potential and time, pulse height, step potential and supporting electrolyte composition are optimized. The calibration graph is linear from 2 nM (0.09 μg L^?1) to 90 nM (4 μg L^?1) for a preconcentration time of 45 s, with correlation coefficient of 0.9995. For a Hg(Ag)FE with a surface area of 7.9 mm² the detection limit for a preconcentration time of 90 s is as low as 5 ng L^?1. The repeatability of the method at a concentration level of the analyte as low as 0.2 μg L^?1, expressed as RSD is 1.9 % (n=5). The proposed method was successfully applied and validated by studying the certified reference material (CRM 320 – river sediment) and natural samples with simultaneous recovery of Sc(III) from spiked water and sediment samples.     

Nafion Coated Silver Amalgam Electrode for Determination of Trace Metals by Anodic Stripping Voltammetry

This paper describes characterization and application of Nafion coated solid silver amalgam electrodes to prevent surface fouling of surfactants in determination of trace metals by differential pulse anodic stripping voltammetry (DPASV). Polymer films of different thickness were tested using Nafion solutions in the range 0.25%–1%. Optimum thickness was archived using a 0.5% Nafion solution, resulting in both increased response and stability over time compared to uncoated electrodes. The influence of model surface active macromolecules was studied using triton X‐100, sodium dodecyl sulfate, dodecyl pyridinium chloride and bovine serum albumin as representatives for surfactants. The resistance to surfactants makes the studied Nafion coated solid silver amalgam electrodes an interesting alternative for practical use in environmental monitoring.     

TiC Working Electrode. Voltammetric Characteristics and Application for Determination of Lead Traces by Stripping Voltammetry

The TiC working electrode was tested as a novel, potential electrode for anodic stripping voltammetric determination of lead(II) ions traces. To demonstrate the practical applicability of the TiC electrode, an underpotential deposition/dissolution (UPD) phenomena system in electrolyte without removal of oxygen was tested. The electrode was constructed be means of mounting a TiC disk (Ø=3.5 mm) in a resin body. Three compositions of TiC were tested differing in stoichiometry, namely TiC_0.6, TiC_0.8, and TiC_1.0. The key problem is the method of electrochemical activation of the TiC electrode. No or improperly activated electrode is not polarized and is unsuitable as a voltammetric sensor. The TiC electrode was used for the determination of Pb²⁺ in concentrations ranging from 1 to 100 nM. The instrumental parameters, composition of supporting electrolyte and procedures of the electrode activation were optimized. The repeatability of DP ASV runs in synthetic solutions covering the entire concentration range is better than 3%. The calibration curve is characterized by a correlation coefficient of at least 0.999. The detection limit was 2 nM for an electrodeposition time of 30 s. The method enables determination of Pb²⁺ in the presence of, among the others, high excesses of Cd, Cu, In, Sb, Se, and Tl ions as well as surfactants, Triton X‐100 and humic acids. The analysis of Pb²⁺ in synthetic solutions with and without surfactants, certified reference material and natural water samples have been performed. The voltammetric data were associated with the structural characterization of the electrode surface using scanning electron microscopy (SEM) and X‐ray fluorescence spectroscopy (XRF).     

Determination of Folic Acid by Adsorptive Stripping Voltammetry at a Lead Film Electrode

An adsorptive stripping voltammetric procedure for the determination of folic acid at an in situ plated lead film electrode was described. Formation of lead film on a glassy carbon substrate and accumulation of folic acid was performed simultaneously from an acetate buffer solution of pH 5.6 at the potential ?0.88 V. The measurements were carried out from aerated solutions. The calibration graph for an accumulation time of 300 s was linear from 2×10^?9 to 5×10^?8 mol L^?1. The detection limit was 7×10^?10 mol L^?1, the relative standard deviation for 2×10^?8 mol L^?1 of folic acid was 3.9%. The proposed procedure was applied to folic acid determinations in pharmaceutical preparations.     

A Highly Sensitive Method for Determination of Monobutyltin in Aqueous Media by Stripping Voltammetry at a Renewable Silver Amalgam Annular Band Electrode

An adsorptive stripping voltammetric (AdSV) procedure for the determination of monobutyltin in aqueous media at a silver liquid amalgam film‐modified silver solid amalgam annular band electrode (AgLAF? AgSAE) is described. Determination of monobutyltin proceeds in two steps. At the beginning monobutyltin ions (BuSn³⁺) are accumulated from 0.1 M NH₄NO₃ and 10 % ethanol solution at a potential of ?0.2 V, than the BuSn⁰ film is preconcentrated at the working electrode surface at a potential of ?0.7 V. After this step the DP AdSV voltammogram is recorded. The analytical parameters and the procedure of the electrode regeneration and activation were optimized. The calibration curve of monobutyltin in the range 0.02–0.30 mg L^?1 is linear (r=0.9973). The detection limit for 5 s of preconcentration, calculated as 3σ of the blank was equal to 0.004 mg L^?1, repeatability of the peak current was 1.8 % (n=5). Repeatability and sensitivity of monobutyltin determination depends strongly on the analyzed solution properties, measurement conditions and the working electrode quality. The proposed procedure was tested by means of monobutyltin determination in tap waters.     

Application of Square Wave Anodic Stripping Voltammetry for Determination of Traces of Ti(I) at Carbon Electrodes In Situ Modified with Bi Films

Bismuth films deposited in situ at glassy carbon and carbon film electrodes were tested for the determination of traces of Tl(I) separately and together with Zn(II) and Pb (II), in acetate buffer solution pH 3.7, using square wave anodic stripping voltammetry. Electrochemical impedance spectra in the presence of Tl(I) showed differences between the electrode substrates. The sensitivity to Tl does not depend on the presence of other ions, and was better at carbon film electrodes, although the 2 nmol L^?1 detection limit was independent of electrode substrate. Application to the measurement of Tl(I) in commercial berry juice is demonstrated.     

Elimination of SAS Interferences in Catalytic Adsorptive Stripping Voltammetric Determination of Cr(VI) by Means of Fumed Silica

In the work the procedure of chromium(VI) determination by catalytic adsorptive stripping voltammetry (CAdSV) with application of fumed silica, is presented. Two variants of the method are proposed: in the first fumed silica is put directly to the electrolytic cell containing tested solution, in the second the silica is shaken with the sample and next centrifuged. The effectiveness of many surface‐active substances removal from synthetic solutions as well as natural water samples, is studied. In the experiments the fumed silica (Sigma‐Aldrich) of the specific surface area in the range 200–390 m² g^?1 was used. Two types of the working electrodes were applied, i.e., hanging mercury drop electrode (HMDE) and cyclic renewable mercury film electrode (Hg(Ag)FE). In the silica presence i) the relative standard deviation (RSD) for 0.1 μg L^?1 Cr(VI) is <2% (HMDE) and <5% (Hg(Ag)FE), n=7, ii) the detection limits estimated deposition time 20 s were respectively 14 ng L^?1 (HMDE) and 22 ng L^?1 (Hg(Ag)FE). The accuracy of the method was tested by studying the recovery of Cr(VI) from spiked natural water samples.     

Renewable Ceramic (TiN) Ring Electrode in Stripping Voltammetry. Determination of Pb(II) Without Removal of Oxygen

Characteristic features of the process of Pb(II) reduction and oxidation at a renewable ceramic ring electrode (RCRE) were studied by stripping voltammetry. The main constituents of the RCRE are: a specially constructed TiN ring electrode, a silver sheet used as silver counter/quasi‐reference electrode and a silicon O‐ring are fastened together in a polypropylene body. The renovation of this electrode is carried out through mechanical removal of solid contaminants and electrochemical activation in the electrolyte which fills the RCRE body. The optimal measurement conditions, composition of supporting electrolyte and procedures of the electrode activation were selected. The measurements were carried out from nondeaerated solutions. As shown on selected examples, RCRE exhibits good performance in underpotential deposition stripping voltammetry (UPD‐SV) applied for the determination of lead(II) in synthetic solutions with and without surfactants and in certified reference materials. The peak current is proportional to the concentration of lead(II) over the range 2×10^?9–1×10^?7 mol L^?1, with a 3σ detection limit of 1×10^?9 mol L^?1 with an accumulation time of 30 s. The obtained results showed good reproducibility, (RSD=2–5%; n=5) and reliability.     

Determination of Folic Acid at a Bismuth Film Electrode by Adsorptive Stripping Voltammetry

This article reports a new simple and sensitive method for the determination of folic acid by adsorptive stripping voltammetry. The method is based on the accumulation of folic acid at a bismuth film plated in situ on a glassy carbon substrate. In order to stabilize bismuth ions, sodium potassium tartrate was added to the supporting electrolyte. The bismuth film formation and folic acid accumulation conditions were optimized and measurements were carried without solution deaeration. The calibration graph was linear from 5 × 10^?10 to 2 × 10^?8 mole per liter with an accumulation time of 180 seconds with a limit of detection of 2 × 10^?10 mole per liter. The relative standard deviation for 5 × 10^?9 mole per liter of folic acid was 3.1 percent (n = 5). The method was successfully applied for determination of folic acid in pharmaceutical preparations.     

固态汞合金电极吸附伏安法测定酪氨酸

采用白合金粉与汞混合制成汞合金糊,涂布在固体石蜡碳糊电极表面,固化后制得固态汞合金电极,并首先应用于酪氨酸的测定。在含Co2 的pH 9.2的硼砂-NaOH底液中,用线性扫描伏安法在-0.80~-1.30V范围内进行扫描,酪氨酸于-1.05 V出现灵敏的还原峰,酪氨酸的浓度与峰电流在1.0×10-7~1.0×10-5mol/L范围内呈线性关系。该法已用于复方氨基酸注射液中酪氨酸含量的测定,加标回收率达96%~102%。该电极既保留了汞电极的优点,又避免了汞电极有毒、使用不方便的缺点。     

Oligonucleotide Functionalized Microporous Gold Electrode for the Selective and Sensitive Determination of Mercury by Differential Pulse Adsorptive Stripping Voltammetry (DPAdSV)

Abstract

A novel electrode modified with oligonucleotide and microporous gold was fabricated for the determination of mercury by differential pulse adsorptive stripping voltammetry (DPAdSV). Microporous gold was synthesized by electrochemical reduction using dynamic hydrogen bubble template. The oligonucleotide was immobilized on microporous gold by self-assembly. The prepared electrode exhibited an improved electrochemical response for mercury(II) ion because of the large surface area and excellent electron transfer capacity provided by microporous gold and the specific coordination between mercury ion and thymine bases in oligonucleotides. Under the optimal experiment conditions, the oligonucleotide functionalized microporous gold electrode had a linear relationship between the stripping current and mercury ion concentration in the range from 0.5 to 30?µg/L with a detection limit of 0.021?µg/L. Moreover, the prepared electrode exhibited good selectivity, reproducibility, repeatability and stability. Furthermore, the prepared electrode was applied to detect mercury in tap water with satisfactory results.     

Adsorptive Stripping Voltammetric Determination of Trace Uranium with a Bismuth‐Film Electrode Based on the U(VI)→U(V) Reduction Step of the Uranium‐Cupferron Complex

This work reports the use of adsorptive stripping voltammetry (AdSV) for the determination of uranium on a preplated rotating‐disk bismuth‐film electrode (BiFE). The principle of the method relied on the complexation of U(VI) ions with cupferron and the subsequent adsorptive accumulation of the complex on the surface of the BiFE. The uranium in the accumulated complex was then reduced by means of a cathodic voltammetric scan while the analytically useful U(VI)→U(V) reduction signal was monitored. The experimental variables as well as potential interferences were investigated and the figures of merit of the method were established. Using the selected conditions, the 3σ limit of detection for uranium was 0.1 μg L^?1 at a preconcentration time of 480 s and the relative standard deviation was 4.7% at the 5 μg L^?1 level for a preconcentration time of 120 s (n=8). The accuracy of the method was established by analyzing a reference sea water sample.     

Determination of Ultra Trace Amounts of Uranium (VI) by Adsorptive Stripping Voltammetry Using L-3-(3, 4-dihydroxy phenyl) Alanine as a Selective Complexing Agent

Abstract

The spectrophotometric behavior of uranium (VI) with L-3-(3, 4-dihydroxy phenyl) alanine (LDOPA) reagent revealed that the uranium can form a ML₂ complex with LDOPA in solution. Thus a highly sensitive adsorptive stripping voltammetric protocol for measuring of trace uranium, in which the preconcentration was achieved by adsorption of the uranium-LDOPA complex at hanging mercury drop electrode (HMDE), is described. Optimal conditions were found to be a 0.02 M ammonium buffer (pH 9.5) containing 2.0 × 10^?5 M (LDOPA), an accumulation potential of ? 0.1 V (versus Ag/AgCl) and an accumulation time of 120 sec.

The peak current and concentration of uranium accorded with linear relationship in the range of 0.5–300 ng ml^?1. The relative standard deviation (at 10 ng ml^?1) is 3.6% and the detection limit is 0.27 ng ml^?1. The interference of some common ions was studied. Applicability to different real samples is illustrated. The attractive behavior of this reagent holds great promise for routine environmental and industrial monitoring of uranium.     

Nafion汞膜修饰电极用于阳极溶出伏安法测定痕量铋的研究

本文报道了Nafion汞膜修饰电极及其用于阳极溶出伏安法测定未处理尿样,水样及土样中痕量铋的研究。样品中常共存的Pb(Ⅱ)、Sb(Ⅲ )等19种阳离子及尿样中共存的有机物在实验条件下不干扰。本法不仅选择性好,而且灵敏度也较高。线性范围为2×10~(-10)～1×10~(-7)mol/L。回收率为94～105％。