Electrochemical Sensor for trans‐Resveratrol Determination Based on Indium Tin Oxide Electrode Modified with Molecularly Imprinted Self‐Assembled Films

A voltammetric sensor for sensitive and specific determination of trans‐resveratrol (RES) were prepared based on immobilization of an RES‐imprinted film on the surface of functionalized Indium Tin Oxide (ITO) electrode, which was modified with γ‐methacyloxypropyl trimethoxysilane (γ‐MPS). Cyclic Voltammetry (CV) was presented to extract RES from the molecularly imprinted polymer film and RES were extracted rapidly and completely. The binding performance of the imprinted electrode with the template RES were investigated using differential pulse voltammetry (DPV). The results showed that the imprinted ITO film can give selective recognition to the template RES over that of structurally analogous molecules. A linear response to RES in the concentration range of 2.0×10^?6 M to 2.0×10^?5 M was observed with a correlation coefficient of 0.992, and the detection limit of the electrochemical sensor was 8.0×10^?7 M. Whereas, binding to the reference nonimprinted electrode, made in the same way but without the addition of template RES, there was almost no response to RES.     

Paracetamol Sensor Based on Molecular Imprinting by Photosensitive Polymers

A voltammetric paracetamol sensor based on molecularly imprinted polymeric (MIP) micelles was prepared by direct electrodeposition. The MIP micelles were prepared via macromolecule self‐assembly of an amphiphilic photocrosslinkable copolymer using paracetamol as the template molecule. The resultant molecularly imprinted polymeric micelles swelled with increasing pH, and the disassociation of the micelles occurred at pH above approximately 7.4. A robust MIP film with good solvent resistance was formed on the electrode surface by anodic electrodeposition of the MIP micelles and subsequent photocrosslinking, resulting in the fabrication of a MIP electrochemical sensor for detecting paracetamol. The resultant sensor showed good response and selectivity towards paracetamol. In addition, a wide linear range from 0.01 mmol/L to 8 mmol/L and a low detection limit of 1×10^?6 mol/L for paracetamol detection was demonstrated based on this sensor. The MIP sensor also showed good stability and reversibility which was applied to determine paracetamol commercial tablets.     

分子印迹电化学传感器测定L-色氨酸的研究

报道了一种由溶胶-凝胶法制备的分子印迹电化学传感器,并用于L-色氨酸的测定.印迹聚合物是由四乙氧基硅烷、甲基三甲氧基硅烷、苯基三甲氧基硅烷等聚合而成,L-色氨酸为模板分子.通过循环伏安法验证了印迹膜与模板分子的结合和去除.该传感器对L-色氨酸具有良好的选择性以及高的灵敏度,线性范围为1.0×10-9～1.0×10-5m...     

A Novel Electrochemical Sensor for β2‐Agonists with High Sensitivity and Selectivity Based on Surface Molecularly Imprinted Sol‐gel Doped with Antimony‐Doped Tin Oxide

A novel strategy to improve the sensitivity of molecularly imprinted polymer (MIP) sensors was proposed for the determination of β₂‐agonists. The imprinted sol‐gel film was prepared by mixing silica sol with a functional monomer of antimony‐doped tin oxide (ATO) and a template of β₂‐agonists. ATO, which was embedded in the surface of the molecularly imprinted sol‐gel film, not only provides the excellent conductivity for biosensor but also increases the stability and the surface area of the MIP film. The imprinted sensor was characterised by field emission scanning electron microscope, fourier transform infrared spectroscopy and electrochemical methods. Under the optimal experimental conditions, the peak current was linear with the logarithm of the concentration of clenbuterol (CLB) in the range of 5.5 nM–6.3 µM, and a detection limit of 1.7 nM was obtained. Meanwhile, the electrochemical sensor showed excellent specific recognition of the template molecule among structurally similar coexisting substances. Furthermore, the proposed sensor was satisfactorily applied to determine β₂‐agonists in human serum samples. The good results indicated that highly effective molecularly imprinted sol‐gel films doped with ATO can be employed for other analytes.     

A Biomimetic Potentiometric Sensor Using Molecularly Imprinted Polymer for the Cetirizine Assay in Tablets and Biological Fluids

Despite the increasing number of applications of molecularly imprinted polymers (MIPs) in analytical chemistry, the construction of a biomimetic potentiometric sensor remains still challenging. In this work, a biomimetic potentiometric sensor, based on a non‐covalent imprinted polymer was fabricated for the recognition and determination of cetirizine. The MIP was synthesized by precipitation polymerization, using cetirizine dihydrochloride as a template molecule, methacrylic acid (MAA) as a functional monomer and ethylene glycol dimethacrylate (EGDMA) as a cross linking agent. The sensor showed high selectivity and a sensitive response to the template in aqueous system. The MIP‐modified electrode exhibited Nernstian response (28.0±0.9 mV/decade) in a wide concentration range of 1.0×10^?6 to 1.0×10^?2 M with a lower detection limit of 7.0×10^?7 M. The electrode has response time of ca. 20 s, high performance, high sensitivity, and good long term stability (more than 5 months). The method was satisfactory and used to the cetirizine assay in tablets and biological fluids.     

Development of a Creatinine Sensor Based on a Molecularly Imprinted Polymer‐Modified Sol‐Gel Film on Graphite Electrode

An electrochemical creatinine sensor based on a molecularly imprinted polymer (MIP)‐modified sol‐gel film on graphite electrode was developed. The surface coating of MIP over sol‐gel was advantageous to obtain a porous film with outwardly exposed MIP cavities for unhindered selective rebinding of creatinine from aqueous and biological samples. A fast differential pulse, cathodic stripping voltammetric response of creatinine can be obtained after being preanodized the sensor in neutral medium containing appropriate amount of creatinine at +1.8 V versus SCE for 120 s. A linear response over creatinine concentration in the range of 1.23 to 100 μg mL^?1 was exhibited with a detection limit of 0.37 μg mL^?1 (S/N=3).     

Biomimetic properties and surface studies of a piezoelectric caffeine sensor based on electrosynthesized polypyrrole

An approach for preparing a chemical sensor for caffeine through the combination of molecularly imprinted polypyrrole and a piezoelectric quartz transducer was proposed. The caffeine-imprinted polymer was synthesized using galvanostatic electropolymerization of pyrrole monomer directly onto one of the gold electrodes of a 9 MHz AT-cut quartz crystal in the presence of caffeine. The optimum conditions for the electrosynthesis of the reagent phase were established. Caffeine molecules were entrapped in the matrix of polymer film, and were removed by subsequent washing with water, leaving behind pores capable of recognizing the target analyte molecule.The caffeine sensor was fixed in a measuring cell and measurement of the resonant frequency of the quartz crystal as it comes in contact with the caffeine solution was carried out in a stopped flow mode. A steady-state response was achieved in about 10 min. The sensor exhibited a linear relationship between the frequency shift and the ln of caffeine concentration in the range of 0.1-10 mg/mL (correlation coefficient, r = 0.9882). The sensitivity of the sensor was about 255 Hz/ln concentration (mg/mL). A good repeatability, R.S.D. = 9 (n = 6) for 0.5 mg/mL caffeine solution was also observed. The use of the sensor can present a potential low-cost option for determining caffeine.Surface analytical techniques such as scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) were performed on the polymer coating in order to elucidate the imprinting process and rebinding of caffeine to the polymer matrix during the sensing process. The SEM micrographs and XPS spectra revealed features and structures that could support the imprinting and recognition of caffeine molecule by the imprinted polymer.     

利用分子印迹技术预处理生物样品中头孢药物的研究

优化了头孢硫脒分子印迹聚合物的合成条件,探讨了分子印迹技术和固相萃取联用对血浆中头孢硫脒的分离富集,发现用4-乙烯基吡啶作功能单体合成的分子印迹聚合物作为固相萃取填充料,能定量吸附血浆中的头孢硫脒,并初步研究了其吸附机理。     

Highly Selective Molecularly Imprinted Polymer Sensor for Indium Detection Based on Recognition of In‐Alizarin Complexes

A highly selective molecularly imprinted polymer electrochemical sensor for In³⁺ detection was proposed. In³⁺ ion was chelated with alizarin red S to form a complex In‐ARS. The complex was used as the template molecule to prepare a molecularly imprinted polymer (MIP) based sensor. The selectivity of the sensor was improved significantly due to the three‐dimensional specific structure of the complex, and the selective complexation of ligands for metal ions. Moreover, the sensitivity of the proposed sensor was improved by recording the reductive current of ligand in complex. This technique was highly sensitive for quantitative analysis of In³⁺ in the concentrations ranged from 1×10^?8 mol/L to 2.5×10^?7 mol/L with a detection limit of 4.7×10^?9 mol/L. The proposed sensor has been successfully used in detecting In³⁺ in real samples.     

吲哚-3-乙酸分子印迹聚合物膜电化学传感器的研制

利用分子印迹技术,以吲哚-3-乙酸(IAA)为模板分子,甲基丙烯酸为单体,在玻碳电极表面采用原位聚合制备分子印迹敏感膜.采用方波伏安法对吲哚乙酸在该印迹电极上的电化学行为进行了研究.结果表明,0.62 V(vs.SCE)处的峰电流与吲哚乙酸的浓度在5.0×10-6～2.0×10-4mol/L范围内呈线性关系,检出限(S...     

基于乙硫基取代的三层酞菁铕二聚体修饰ITO电极构筑电化学多巴胺和尿酸传感器

通过在水平和垂直两个方向上来扩展酞菁配合物的共轭结构, 合成了三明治三层酞菁铕二聚体配合物[Pc(SC₂H₅)₈]₂Eu₂[BiPc(SC₂H₅)₁₂]Eu₂[Pc(SC₂H₅)₈]₂, 使用Quasi-Langmuir-Sh?fer(QLS)方法将配合物薄膜修饰在氧化铟锡导电玻璃(ITO)电极表面, 利用多种谱学手段对配合物分子在薄膜内的排列进行表征, 发现分子采取J聚集模式Edge-on排列在ITO电极表面, 该薄膜具有良好的半导体性质, 导电率高达8.86×10^-5 S/cm. 将配合物薄膜修饰的ITO电极成功应用于多巴胺(DA)和尿酸(UA)的电化学灵敏检测, 最低检测限分别达到1.35和1.64 μmol/L, 灵敏度分别达到110和186.5 mA·μL·mol^-1 ·cm^-2.     

Non-Aqueous Assay System for Phenobarbital Using Biomimetic Bulk Acoustic Wave Sensor Based on a Molecularly Imprinted Polymer

ABSTRACT

A new biomimetic bulk acoustic wave (BAW) sensor based on a molecularly imprinted polymer (MIP) was fabricated and applied for the determination of phenobarbital The MIP was synthesized using phenobarbital as the template molecule and methacrylic acid as the functional monomer by the non-covalent method. In absolute ethanol, the sensor exhibited good selectivity and sensitivity. A linear relationship between 9.0×10^?8 M and 5.0×10^?5 M was revealed. The determination limit was 5.0×10^?8 M. In harsh chemical environments such as high temperature, organic solvent, bases, acids, etc., the sensor still exhibited long-time stability. Satisfactory results of real sample assay were obtained by the proposed method.     

基于门控制电催化效应的分子印迹传感器

以绿麦隆为模板分子,在镍电极表面聚合制得绿麦隆分子印迹膜.洗脱后的分子印迹膜重新吸附不同浓度绿麦隆分子,在印迹膜上形成不同量的印迹孔穴,H2O2通过印迹孔穴在镍电极表面产生电催化氧化,从而形成门控制电催化效应,以此对绿麦隆进行定量分析.研究表明,镍电极对H2O2有较好的催化效果,分子印迹聚合膜中模板分子、功能单体和交联剂的摩尔配比为1∶12∶30,重吸附时间为10 min,测试缓冲液pH=7.2.H2O2的催化电流值与绿麦隆浓度在1.0× 10-4～4.0× 10-7 mol/L范围内呈良好的线性关系;检出限为2.9×10-8 mol/L.将传感器应用于农田水样的检测,其回收率在97％～103％之间.     

Preparation and evaluation of a molecularly imprinted sol–gel material as the solid‐phase extraction adsorbents for the specific recognition of cloxacilloic acid in cloxacillin

Highly selective molecularly imprinted polymers on the surface of silica gels were prepared by a sol–gel process and used as solid‐phase extraction adsorbents for the specific recognition, enrichment and detection of cloxacilloic acid in cloxacillin. The obtained polymers were characterized by scanning electron microscopy, FTIR spectroscopy, nitrogen adsorption and desorption, elemental analysis and thermogravimetric analysis. The imprinted polymers not only possessed high adsorption capacity (6.5 μg/mg), but also exhibited fast adsorption kinetics (they adsorb 80% of the maximum amount within 20 min) and excellent selectivity (the imprinted factor was 3.6). A method using the imprinted polymers as solid‐phase extraction adsorbents coupled with high‐performance liquid chromatography was established with good specificity, linearity (r = 0.9962), precision (ranging from 0.5 to 6.7%), accuracy (ranging from 93.9 to 97.7%) and extraction recoveries (ranging from 78.8 to 89.8%). The limits of detection and quantification were 0.07 and 0.25 mg/g, respectively. This work could provide a promising method in the enrichment, extraction and detection of allergenic impurities in the manufacture, storage and application of cloxacillin.     

分子印迹电位型传感器快速检测猪尿液中的克伦特罗

以盐酸克伦特罗为模板分子,采用沉淀聚合法合成了克伦特罗的分子印迹聚合物,并以其为离子载体,制得分子印迹聚合物膜克伦特罗离子选择性电极.在最优实验条件下,电极对克伦特罗阳离子的检出限可达7.0×10-8mol/L,线性范围为1.0×10 7～1.0×10-4 mol/L,能斯特斜率为55.7 mV/decade.此电极具有优越的选择性、快速的响应时间以及良好的稳定性;已成功应用于实际猪尿样品中克伦特罗的测定,加标回收率为98％～107％,检测时间小于3 min.     

碳纳米管修饰电极分子印迹传感器快速测定沙丁胺醇

以单壁碳纳米管(SWNTs)为电极材料,应用分子印迹技术,以邻苯二胺为功能单体、沙丁胺醇为模板,采用电化学聚合法制备了一种新型的快速检测沙丁胺醇分子印迹传感器,并运用电化学方法去除模板.在磷酸盐缓冲溶液(PBS)中,利用线性溶出伏安法对印迹和非印迹膜的性能进行了比较,对分子印迹膜的影响因素进行了优化.实验表明,本传感器...     

Effective separation of dopamine from bananas on 2-(3,4-dimethoxyphenyl)ethylamine imprinted polymer

A 2-(3,4-dimethoxyphenyl)ethylamine imprinted polymer (MIP(pt) ) was prepared via the precipitation polymerization together with a nonimprinted polymer (NIP). The morphology of particles was investigated by scanning electron microscopy and the specific surface areas were estimated by methylene blue adsorption (60.5 ± 3.5 and 36.9 ± 1.2 m(2)/g for MIP(pt) and NIP, respectively). The binding experiments were performed to determine the binding capacity of MIP(pt)/NIP particles toward dopamine. Next, the effects of solvents on loading, washing, and eluting steps were examined on solid-phase extraction (SPE). Methanol-water 85:15 v/v (loading step), methanol (washing step), and 0.04 M aqueous ammonium acetate-methanol 30:70 v/v (eluting step) were selected as the most effective systems. Described SPE protocol was successfully applied for separation of dopamine on 2-(3,4-dimethoxyphenyl)ethylamine imprinted particles. Finally, the molecularly imprinted polymer was used for determination of dopamine in spiked banana extract. The total recovery of dopamine from MIP(pt) was equal to 88.5 ± 4.6%, but from NIP was only 12.8 ± 2.3%. The developed material and method were demonstrated to be applicable for the separation of dopamine from bananas. The commercial sorbent C18 was not suitable to such application.     

Sol-Gel Imprinted Polymers Based Electrochemical Sensor for Paracetamol Recognition and Detection

Molecular imprinting and sol-gel technique were combined to develop a molecular imprinted polymer (MIP) based electrochemical sensor in this work. With the successive modification of multi-walled carbon nanotubes (MWNTs) and gold nanoparticles (GNPs), a modified glassy carbon electrode (GCE) was immersed in a sol-gel solution in the presence of paracetamol (PR) for the electropolymerization to fabricate an imprinted sensor. Scanning electron microscopy (SEM), electrochemical impedance spectroscopy (EIS), and differential pulse voltammetry (DPV) were employed to characterize the constructed sensor. The factors for the sensor preparation, the electropolymerization potential range, the monomer concentration, and the scan rate for the sensor preparation were optimized. The sensor displayed an excellent recognition capacity toward PR compared with other analogues. Additionally, the DPV peak current was linear to the PR concentration in the range from 8.0 × 10^?8 to 5.0 × 10^?5 mol/L, with a detection limit of 4.0 × 10^?8 mol/L. The prepared sensor also showed satisfactory reproducibility and regeneration capacity.     

A High Sensitivity Electrochemical Sensor Based on Fe3+‐Ion Molecularly Imprinted Film for the Detection of T‐2 Toxin

The excellent detection sensitivity in various matrices of T‐2 toxin (T‐2), which has cytotoxic and immunosuppressive effects in DNA and RNA synthesis, is a highly desirable characteristic. A sensitive molecularly imprinted electrochemical sensor was constructed for the selective detection of T‐2. In this study, iron ions (Fe³⁺) were introduced to increase the chelation of the metal ions and templates for preparing molecularly imprinted polymers (MIPs). With the increased chelation of the metal ions and templates, the selectivity and sensitivity of the MIPs were effectively improved. The imprinted sensor was successfully employed to detect T‐2 in cereals and human serum samples.