Direct Electrochemistry of Myoglobin in a Nafion‐Ionic Liquid Composite Film Modified Carbon Ionic Liquid Electrode

In this paper two kinds of ionic liquids (ILs) were used for the construction of a myoglobin (Mb) electrochemical biosensor. Firstly a hydrophilic ionic liquid of 1‐ethyl‐3‐methylimidazolium tetrafluoroborate (EMIMBF₄) was used as binder to prepare a carbon ionic liquid electrode (CILE), then a Nafion and hydrophobic ionic liquid of 1‐butyl‐3‐methylimidazolium hexafluorophosphate (BMIMPF₆) composite film was applied on the surface of the CILE. The direct electrochemistry of Mb in the Nafion‐BMIMPF₆/CILE was achieved with the cathodic and anodic peak potentials located at ?0.345 V and ?0.213 V (vs. SCE). The formal potential (E°′) was located at ?0.279 V, which was the characteristic of Mb Fe^III/Fe^II redox couples. The electrochemical behaviors of Mb in the Nafion‐ionic liquid composite film modified CILE were carefully investigated. The Mb modified electrode showed good electrocatalytic behaviors to the reduction of trichloroacetic acid (TCA) and NaNO₂. Based on the Nafion‐BMIMPF₆/Mb/CILE, a new third generation reagentless biosensor was constructed.     

Electrochemical Surface Structuring with Polyaniline Wrapped Hb for Hydrogen Peroxide Biosensing

Through the electrodeposition of aniline with hemoglobin (Hb) on zincoxide‐gold colloidal sols (ZnO‐AuNPs) modified indium oxide electrode, a hydrogen peroxide (H₂O₂) biosensor was constructed. Polyaniline (PANI) form a nano‐cage wrapped Hb, which provided a comfortable and stable site for the immobization of Hb. UV‐vis spectrum was employed to characterize Hb retained original structure in the resulting Hb‐PANI/ZnO‐AuNPs membrane. Electrochemical investigation of the biosensor showed a pair of well‐defined, quasi‐reversible redox peaks with E_pa= ‐0.139 V and E_pc = ‐0.238 V (vs. SCE) in 0.1 M pH 7.0 phosphate buffer solution at the scan rate of 100 mV/s. The biosensor displayed a fast response time (<3 s) and broad linear response to H₂O₂ in the range from 1.5 μM to 1.7 mM with a detection limit of 0.8 μM (S/N = 3).     

Direct Electrochemistry of Hemoglobin on Single‐Walled Carbon Nanotubes Modified Carbon Ionic Liquid Electrode and Its Electrocatalysis

In this article we report on the fabrication of a carbon ionic liquid electrode (CILE) by using a room temperature ionic liquid of 1‐butyl‐3‐methylimidazolium hexafluorophosphate (BMIMPF₆) as binder. It was further modified by single‐walled carbon nanotubes (SWCNTs) to get a SWCNTs modified CILE denoted as SWCNTs/CILE. The redox protein of hemoglobin (Hb) was further immobilized on the surface of SWCNTs/CILE with the help of Nafion film. UV‐vis and FT‐IR spectra indicated that the immobilized Hb retained its native conformation in the composite film. The direct electrochemistry of Hb on the SWCNTs/CILE was carefully studied in pH 7.0 phosphate buffer solution (PBS). Cyclic voltammetric results indicated that a pair of well‐defined and quasireversible voltammetric peaks of Hb heme Fe(III)/Fe(II) was obtained with the formal potential (E°') at ?0.306 V (vs. SCE). The electrochemical parameters such as the electron transfer coefficient (α), the electron transfer number (n) and the apparent heterogeneous electron transfer rate constant (k_s) were calculated as 0.34, 0.989 and 0.538 s^?1, respectively. The fabricated Hb modified electrode showed good electrocatalytic ability to the reduction of trichloroacetic acid (TCA) in the concentration range from 20.0 to 150.0 mmol/L with the detection limit of 10.0 mmol/L (3σ).     

Direct Electron Transfer and Electrocatalysis of Myoglobin Based on its Direct Immobilization on Carbon Ionic Liquid Electrode

Direct electron transfer of myoglobin (Mb) was achieved by its direct immobilization on carbon ionic liquid electrode (CILE) with a conductive hydrophobic ionic liquid, 1‐butyl pyridinium hexaflourophosphate ([BuPy][PF₆]) as binder for the first time. A pair of well‐defined, quasi‐reversible redox peaks was observed for Mb/CILE resulting from Mb redox of heme Fe(III)/Fe(II) redox couple in 0.1 M phosphate buffer solution (pH 7.0) with oxidation potential of ?0.277 V, reduction potential of ?0.388 V, the formal potential E°′ (E°′=(E_pa+E_pc)/2) at ?0.332 V and the peak‐to‐peak potential separation of 0.111 V at 0.5 V/s. The average surface coverage of the electroactive Mb immobilized on the electrode surface was calculated as 1.06±0.03×10^?9 mol cm^?2. Mb retained its bioactivity on modified electrode and showed excellent electrocatalytic activity towards the reduction of H₂O₂. The cathodic peak current of Mb was linear to H₂O₂ concentration in the range from 6.0 μM to 160 μM with a detection limit of 2.0 μM (S/N=3). The apparent Michaelis–Menten constant (K and the electron transfer rate constant (k_s) were estimated to be 140±1 μM and 2.8±0.1 s^?1, respectively. The biosensor achieved the direct electrochemistry of Mb on CILE without the help of any supporting film or any electron mediator.     

Voltammetric Studies of Cadmium‐ and Zinc‐Containing Metallothioneins at Nafion‐Coated Mercury Thin Film Electrodes

Voltammetric studies of rabbit liver metallothioneins (MTs, containing both Zn and Cd ions) and Zn₇‐MT were carried out at Nafion‐coated mercury film electrodes (NCMFEs). The accumulation of MT molecules into the NCMFEs enhances the voltammetric signals and the electrostatic interaction between the Nafion membrane and MT facilitates facile electron transfer reactions. Two well‐defined redox waves, with reduction potential (E_pc) values at ?0.740 and ?1.173 V, respectively, were observed. The peak at E_pc =?0.740 V is attributable to the reduction of the Cd‐MT complex, whereas that at E_pc=?1.173 V was assigned to the reduction of the Zn‐MT complex. Zn₇‐MT exhibits only one redox wave with E_pc=?1.198 V. The NCMFE was found to be more advantageous than thin mercury film electrode (MFE), because the pristine metal ions in MTs (e.g., Cd²⁺ and/or Zn²⁺) are not significantly replaced by Hg²⁺. The NCMFE is also complementary to Nafion‐coated bismuth film electrode in that it has a greater hydrogen overpotential, which allows the reduction of the Zn‐MT complex to be clearly observed. Moreover, intermetallic compound formation between Cd and Zn appears to be less serious at NCMFEs. Consequently, the amounts of Cd and Zn deposited into the electrode upon the reduction reactions can be quantified more accurately.     

Electrochemical Biosensor Based on Carbon Ionic Liquid Electrode Modified with Nafion/Hemoglobin/DNA Composite Film

A new electrochemical biosensor was constructed by immobilization of hemoglobin (Hb) on a DNA modified carbon ionic liquid electrode (CILE), which was prepared by using 1‐ethyl‐3‐methylimidazolium tetrafluoroborate (EMIMBF₄) as the modifier. UV‐vis absorption spectroscopic result indicated that Hb remained its native conformation in the composite film. The fabricated Nafion/Hb/DNA/CILE was characterized by scanning electron microscopy (SEM), electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). A pair of well‐defined redox peaks was obtained on the modified electrode, indicated that the Nafion and DNA composite film provided an excellent biocompatible microenvironment for keeping the native structure of Hb and promoting the direct electron transfer rate of Hb with the basal electrode. The electrochemical parameters of Hb in the composite film were further calculated with the results of the charge transfer coefficient (α) and the apparent heterogeneous electron transfer rate constant (k_s) as 0.41 and 0.31 s^?1. The proposed electrochemical biosensor showed good electrocatalytic response to the reduction of trichloroacetic acid (TCA), H₂O₂, NO and the apparent Michaelis–Menten constant (K_M^app) for the electrocatalytic reaction was calculated, respectively.     

A Hydrogen Peroxide Biosensor Based on Room Temperature Ionic Liquid Functionalized Graphene Modified Carbon Ceramic Electrode

A room temperature ionic liquid (IL) 1‐butyl‐3‐methylimidazolium hexafluorophosphate functionalized graphene (GE) was prepared and a hydrogen peroxide (H₂O₂) biosensor was fabricated by immobilizing hemoglobin (Hb) into the IL‐GE composite film. UV‐visible and Fourier transform infrared spectra of the composite film indicated that Hb retained its native structure in the film. Electrochemical investigation of the biosensor showed a pair of well‐defined, quasi‐reversible redox peaks with E_pa=?0.209 V and E_pc= ?0.302 V (vs. SCE) in pH 7.0 phosphate buffer solution at the scan rate of 100 mV/s. To the reduction of H₂O₂, the biosensor had a good linear range from 8.0×10^?7 to 1.8×10^?4 mol/L with a detection limit of 3.0×10^?7 mol/L. The apparent Michaelis‐Menten constant K^app_M was estimated to be 3.4×10^?5 mol/L.     

Electrodeposition CaCO3 Nanoparticles‐chitosan Composite Film on Carbon Ionic Liquid Electrode as a Platform for Hemoglobin Electrochemical Biosensor

By one‐step co‐electrodeposition CaCO₃ nanoparticles‐chitosan composite film on carbon ionic liquid electrode (CILE), and then by spreading the composition of hemoglobin (Hb) and chitosan on the nanoCaCO₃‐chi/CILE, a Hb‐chi/nanoCaCO₃‐chi/CILE was fabricated and the direct electrochemistry and electrocatalysis of Hb at the electrode was investigated. The electrochemical impedance spectroscopy of the modified electrode showed the electron transfer resistance was 1166 Ω. Investigation results of cyclic voltammetrys showed a pair of well‐defined and quasireversible redox peak of Hb with the formal potentials of ‐0.295 V (vs. SCE) in 0.1 mol·L^‐1 pH 7.0 PBS; the response time of the reduction peak currents of Hb was lower than 3s; a linear range for determination of H₂O₂ was from 5.0 μmol·L^‐1 to 1.3 mmol·L^‐1 with a detection limit of 1.6 μmol·L^‐1 (S/N = 3) and a sensitivity of 0.16 A·M^‐1·cm^‐2; the electron transfer rate constant and the apparent Michaelis‐Menten constant of Hb were 1.98 s^‐1 and 0.81 mmol·L^‐1, respectively. As a result, the case of the one‐step co‐electrodeposition and the promising feature of biocomposite could serve as a versatile platform for the fabrication of electrochemical biosensors.     

Direct Electron Transfer of Hemoglobin on a Carbon Ionic Liquid Electrode with TiO2 Nanopatricle as Enhancer

Room temperature ionic liquids (RTILs) N‐butylpyridinium hexafluorophosphate (BPPF₆) modified carbon paste electrode (CILE) was fabricated and applied to adsorb the hemoglobin (Hb) and TiO₂ nanoparticles on the electrode surface step by step to form a Hb modified electrode noted as TiO₂/Hb/CILE. UV‐Vis and FT‐IR spectra showed that Hb in the film retained its native conformations. Cyclic voltammetric experiments indicated that a pair of well‐defined quasi‐reversible redox peaks appeared with the formal potential (E^0′) located at ?0.251 V (vs. SCE) at pH 7.0 phosphate buffer solution (PBS), which was the characteristic of heme Fe(III)/Fe(II) redox couples. Electrochemical parameters of the Hb in the film such as the electron transfer coefficient (α), the electron transfer number (n) and the standard electron transfer rate constant (k_s) were estimated as 0.469, 0.87 and 0.635 s^?1, respectively.     

Cu3Mo2O9 nanosheet incorporated with hemoglobin on carbon ionic liquid electrode for the direct electrochemistry and electrocatalysis

In this paper Cu₃Mo₂O₉ nanosheet was prepared by a hydrothermal method and further used to investigate the direct electrochemistry of hemoglobin (Hb) with a carbon ionic liquid electrode (CILE) as the substrate electrode. Hb was mixed with Cu₃Mo₂O₉ nanosheet and cast on the CILE surface with chitosan (CTS) as the film-forming material. UV-vis and FT-IR spectroscopic results showed that Hb remained in its native structure in the composite film. Direct electron transfer of Hb on the modified electrode was realized with a pair of well-defined quasi-reversible redox waves that appeared on cyclic voltammograms. The redox peak potential appeared at ?0.252 V (E _pc) and ?0.141 V (E _pa), respectively, with the formal peak potential calculated as ?0.196 V, which was the characteristic of electroactive center of Hb heme Fe(III)/Fe(II). The result could be attributed to the presence of Cu₃Mo₂O₉ nanosheet on the electrode surface that was of benefit for the protein orientation and promoted direct electron transfer between the redox active center of Hb and the substrate electrode. The CTS/Cu₃Mo₂O₉–Hb/CILE showed good electrocatalytic ability in reducing different substrates such as trichloroacetic acid, H₂O₂ and O₂, with wider linear range and lower detection limit, thus exhibiting the potential application of the Cu₃Mo₂O₉ nanosheet in third-generation electrochemical biosensors.     

Electrochemical Behavior of a Glassy Carbon Electrode Chemically Modified with Nickel Pentacyanonitrosylferrate in Presence of Sulfur Compounds

The glassy carbon electrode was modified with a nickel pentacyanonitrosylferrate film by electrodeposition of Ni and subsequent derivatization with NaPCNF. The film was characterized by XPS and electrochemical methods. Cyclic voltammetry of the NiPCNF onto the GC shows a redox couple (Fe^III/Fe^II) with E°′ of 538 mV (I_pa/I_pc around 1) and ΔE_p of 93 mV in 0.5 mol L^?1 KNO₃, with a diffusion‐controlled process. There was a decrease of anodic peak currents of the film in the presence of sulfide and 2‐propanethiol due to a precipitation reaction on the film surface by nucleophilic attack.     

Fabrication and Electrochemical Behavior of Hemoglobin Modified Carbon Ionic Liquid Electrode

A new hemoglobin (Hb) and room temperature ionic liquid modified carbon paste electrode was constructed by mixing Hb with 1‐butyl‐3‐methylimidazolium hexafluorophosphate (BMIMPF₆) and graphite powder together. The Hb modified carbon ionic liquid electrode (Hb‐CILE) was further characterized by FT‐IR spectra, scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS). Hb in the carbon ionic liquid electrode remained its natural structure and showed good direct electrochemical behaviors. A pair of well‐defined quasireversible redox peaks appeared with the apparent standard potential (E′) as ?0.334 (vs. SCE) in pH 7.0 phosphate buffer solution (PBS). The electrochemical parameters such as the electron transfer number (n), the electron transfer coefficient (α) and the heterogeneous electron transfer kinetic constant (k_s) of the electrode reaction were calculated with the results as 1.2, 0.465 and 0.434 s^?1, respectively. The fabricated Hb‐CILE exhibited excellent electrocatalytic activity to the reduction of H₂O₂. The calibration range for H₂O₂ quantitation was between 8.0×10^?6 mol/L and 2.8×10^?4 mol/L with the linear regression equation as I_ss (μA)=0.12 C (μmol/L)+0.73 (n=18, γ=0.997) and the detection limit as 1.0×10^?6 mol/L (3σ). The apparent Michaelis–Menten constant (K_M^app) of Hb in the modified electrode was estimated to be 1.103 mmol/L. The surface of this electrochemical sensor can be renewed by a simple polishing step and showed good reproducibility.     

Simultaneous Determination of Dopamine and Ascorbic Acid Using the Nano‐Gold Self‐Assembled Glassy Carbon Electrode

Electrochemical behavior of dopamine (DA) was investigated at the gold nanoparticles self‐assembled glassy carbon electrode (GNP/LC/GCE), which was fabricated by self‐assembling gold nanoparticles on the surface of L ‐cysteine (LC) modified glassy carbon electrode (GCE) via successive cyclic voltammetry (CV). A pair of well‐defined redox peaks of DA on the GNP/LC/GCE was obtained at E_pa=0.197 V and E_pc=0.146 V, respectively. And the peak separation between DA and AA is about 0.2 V, which is enough for simultaneous determination of DA and AA. The peak currents of DA and AA were proportional with their concentrations in the range of 6.0×10^?8–8.5×10^?5 mol L^?1 and 1.0×10^?6–2.5×10^?3 mol L^?1, with the detection limit of 2.0×10^?8 mol L^?1 and 3.0×10^?7 mol L^?1 (S/N=3), respectively. The modified electrode exhibits an excellent reproducibility, sensibility and stability for simultaneous determination of DA and AA in human serum with satisfactory result.     

Electrodeposited Graphene and Silver Nanoparticles Modified Electrode for Direct Electrochemistry and Electrocatalysis of Hemoglobin

By using a 1‐butylpyridinium hexafluorophosphate based carbon ionic liquid electrode (CILE) as the working electrode, graphene (GR) nanosheets and silver nanoparticles (Ag NPs) were step by step electrodeposited on the surface of the CILE with potentiostatic method. The fabricated Ag/GR/CILE was used as a new platform for protein electrochemistry and hemoglobin (Hb) was immobilized on its surface with chitosan (CTS) as film forming material. In 0.1 mol/L phosphate buffer solution, a pair of well‐defined and quasi‐reversible redox peaks appeared on the CTS/Hb/Ag/GR/CILE with a formal peak potential of ?0.202 V (vs. SCE) and a peak‐to‐peak separation (ΔE_p) of 68 mV, which indicated that direct electrochemistry of Hb was realized on the modified electrode. The results could be attributed to the synergistic effects of Ag NPs and GR nanosheets on the electrode surface, which provided a specific three‐dimensional structure with high conductivity and good biocompatibility. The Hb modified electrode showed excellent electrocatalysis to the reduction of trichloroacetic acid in the concentration range from 0.8 to 22.0 mmol/L with a detection limit of 0.42 mmol/L (3σ). Moreover, the modified electrode exhibited favorable reproducibility, long term stability and accuracy, with potential applications in the third‐generation electrochemical biosensor.     

Application of NiMoO4 Nanorods for the Direct Electrochemistry and Electrocatalysis of Hemoglobin with Carbon Ionic Liquid Electrode

In this paper NiMoO₄ nanorods were synthesized and used to accelerate the direct electron transfer of hemoglobin (Hb). By using an ionic liquid (IL) 1‐butylpyridinium hexafluorophosphate (BPPF₆) modified carbon paste electrode (CILE) as the basic electrode, NiMoO₄ nanorods and Hb composite biomaterial was further cast on the surface of CILE and fixed by chitosan (CTS) to establish a modified electrode denoted as CTS/NiMoO₄‐Hb/CILE. UV‐vis and FT‐IR spectroscopic results showed that Hb in the film retained its native structures without any conformational changes. Electrochemical behaviors of Hb entrapped in the film were carefully investigated by cyclic voltammetry with a pair of well‐defined and quasi‐reversible redox voltammetric peaks appearing in phosphate buffer solution (PBS, pH 3.0), which was attributed to the direct electrochemistry of the electroactive center of Hb heme Fe(III)/Fe(II). The results were ascribed to the specific characteristic of NiMoO₄ nanorods, which accelerated the direct electron transfer rate of Hb with the underlying CILE. The electrochemical parameters of Hb in the composite film were further carefully calculated with the results of the electron transfer number (n) as 1.08, the charge transfer coefficient (α) as 0.39 and the electron‐transfer rate constant (k_s) as 0.82 s^?1. The Hb modified electrode showed good electrocatalytic ability toward the reduction of trichloroacetic acid (TCA) in the concentration range from 0.2 to 26.0 mmol/L with a detection limit of 0.072 mmol/L (3σ), and H₂O₂ in the concentration range from 0.1 to 426.0 µmol/L with a detection limit of 3.16×10^?8 mol/L (3σ).     

Direct electrochemistry and electrocatalysis of hemoglobin on gold nanoparticle decorated carbon ionic liquid electrode

In this paper a carbon ionic liquid electrode (CILE) was fabricated by using ionic liquid 1-ethyl-3-methylimidazolium ethylsulfate ([EMIM]EtOSO₃) as modifier and further gold nanoparticles were in situ electrodeposited on the surface of CILE. The fabricated Au/CILE was used as a new platform for the immobilization of hemoglobin (Hb) with the help of a Nafion film. Electrochemical experimental results indicated that direct electron transfer of Hb was realized on the surface of Au/CILE with a pair of well-defined quasi-reversible redox peaks appeared. The formal peak potential (E⁰′) was obtained as −0.210 V (vs. SCE) in pH 7.0 phosphate buffer solution (PBS), which was the characteristic of Hb heme Fe(III)/Fe(II) redox couple. The fabricated Nafion/Hb/Au/CILE showed excellent electrocatalytic activity to the reduction of trichloroacetic acid (TCA) and the reduction peak current was in proportional to TCA concentration in the range from 0.2 to 18.0 mmol/L with the detection limit as 0.16 mmol/L (S/N = 3). The proposed electrode showed good stability and reproducibility, and it had the potential application as a new third-generation electrochemical biosensor.     

Electrochemical behavior of horseradish peroxidase on WS2 nanosheet‐modified electrode and electrocatalytic investigation

In this paper, a WS₂ nanosheet was modified on the surface of a carbon ionic liquid electrode (CILE), and horseradish peroxidase (HRP) was further fixed on the electrode with a Nafion film. Direct electrochemistry and bioelectrocatalysis of HRP incorporated on the modified electrode were investigated in detail. On Nafion/HRP/WS₂/CILE, a pair of well‐defined quasi‐reversible redox peaks appeared on the cyclic voltammogram, indicating that the presence of the WS₂ nanosheet on the electrode surface could provide a specific interface with large surface area for HRP and its direct electron transfer rate was greatly enhanced. The formal potential (E⁰) obtained was –0.179 V, which was the typical feature of heme Fe(III)/Fe(II) in HRP. The electron transfer coefficient (α) and the heterogeneous electron transfer rate constant (k_s) of HRP were calculated as 0.44 and 1.01 s^–1, respectively. This HRP‐modified electrode showed excellent electrocatalytic activity for the reduction of trichloroacetic acid and NaNO₂ with a wide linear range and low detection limit. Real samples were detected by this proposed method, indicating the successful fabrication of a new third‐generation electrochemical enzyme sensor utilizing the WS₂ nanosheet.     

Direct electrochemistry and electrocatalysis of hemoglobin in sodium alginate film on a BMIMPF6 modified carbon paste electrode

A room temperature ionic liquid (RTIL) modified carbon paste electrode was constructed based on the substitute of paraffin with 1-butyl-3-methyl-imidazolium hexafluorophosphate (BMIMPF₆) as binder for carbon paste. Direct electrochemistry and electrocatalytic behaviors of hemoglobin (Hb) entrapped in the sodium alginate (SA) hydrogel film on the surface of this carbon ionic liquid electrode (CILE) were investigated. The presence of IL in the CILE increased the electron transfer rate and provided a biocompatible interface. Hb remained its bioactivity on the surface of CILE and the SA/Hb modified electrode showed a pair of well-defined, quasi-reversible cyclic voltammetric peaks with the apparent standard potential (E^0′) at about −0.344 V (vs. SCE) in pH 7.0 Britton–Robinson (B–R) buffer solution, which was attributed to the Hb Fe(III)/Fe(II) redox couple. UV–Vis absorption spectra indicated that heme microenvironment of Hb in SA film was similar to its native status. Hb showed a thin-layer electrochemical behavior in the SA film with the direct electron transfer achieved on CILE without the help of electron mediator. Electrochemical investigation indicated that Hb took place one proton with one electron electrode process and the average surface coverage of Hb in the SA film was 3.2 × 10⁻¹⁰ mol/cm². The immobilized Hb showed excellent electrocatalytic responses to the reduction of H₂O₂ and nitrite.     

Direct electrochemistry of hemoglobin in a nafion and CuS microsphere modified carbon ionic liquid electrode and its electrocatalytic behavior

Direct electrochemistry of hemoglobin (Hb) was realized on a Nafion and CuS microsphere composite film modified carbon ionic liquid electrode (CILE) with N-butylpyridinium hexafluorophosphate (BPPF6) as binder. Scanning electron microscopy (SEM), UV-Vis absorption spectroscopy and cyclic voltammetry were used to characterize the fabricated Nafion/CuS/Hb/CILE. Experimental results showed that a pair of well-defined quasi-reversible redox peaks appeared with the formal potential as ?0.386 V (vs. SCE) in pH 7.0 Britton-Robinson (B-R) buffer solution, which was attributed to the Hb heme Fe(III)/Fe(II) redox couples. The electrochemical parameters of Hb in the composite film were carefully investigated with the charge transfer coefficient (α), the electron transfer number (n) and the electron transfer rate constant (k _s) as 0.505, 1.196 and 0.610 s^?1, respectively. The composite film provided a favorable microenvironment for retaining the native structure of Hb. The presence of CuS microspheres showed great improvement on the electron transfer rate of Hb with the CILE, which maybe due to the contribution of specific characteristics of CuS microspheres and the inherent advantages of ionic liquid on the modified electrode. The fabricated Hb modified electrode showed good electrocatalytic ability in the reduction of H₂O₂. The proposed bioelectrode can be used as a new third generation H₂O₂ biosensor.     

Electrochemical Studies of a New Iron Porphyrin Entrapped in a Propylpyridiniumsilsesquioxane Polymer Immobilized on a SiO2/Al2O3 Surface

In this work, a new porphyrin, the 5,10,15,20‐tetrakis‐(2,6‐difluoro‐3‐sulfonatophenyl) porphyrinato iron(III) chloride (denoted as FeTsP) was immobilized on SiO₂/Al₂O₃ (SiAl) coated with n‐propylpyridiniumsilsesquioxane polymer (SiPy⁺Cl^?). The FeTsP was adsorbed on SiAl/SiPyCl by an ion exchange reaction, obtaining a modified solid, SiAl/SiPy/FeTsP, where the porphyrin complex was strongly adhered. Cyclic voltammograms of the SiAl/SiPy/FeTsP carbon paste electrode showed an irreversible response, with an oxidation peak at E_pa=0.40 V and nondefined reduction peak at E_pc=0.15 V (vs. SCE). These peaks were not observed for the nonmetallated porphyrin, indicating that they probably correspond to the Fe(III)/Fe(II) process. Studies made in solutions having different pH, (between pH 2 and 9) using the modified electrode showed that the peak potentials and the current density were not affect by pH changes, indicating that the iron porphyrin is very stable and strongly entrapped in the matrix. The modified electrode presented the property to electrocatalyze the eletrooxidation of hydrazine at 0.41 V (vs. SCE), at pH 7. The potentiality of the SiAl/SiPy/FeTsP electrode as a sensor for hydrazine was evaluated by the using the chronoamperometric technique. A linear response was obtained in the concentration range between 5×10^?5 and 6×10^?4 mol L^?1 of hydrazine.