Stability Improvement of Prussian Blue by a Protective Cellulose Acetate Membrane for Hydrogen Peroxide Sensing in Neutral Media

The cellulose acetate covered Prussian blue modified glassy carbon electrode (GCE/PB/CA) was fabricated as a novel hydrogen peroxide sensor. It was shown by scanning electron microscope (SEM) and atomic force microscope (AFM) that Prussian blue was covered and protected by cellulose acetate perfectly. The modified electrode showed a good electrocatalytic activity for H₂O₂ reduction in neutral aqueous solution. H₂O₂ was detected amperometrically in 0.05 mol/L phosphate buffer solutions (pH 7.0, containing 0.1 mol/L KCl as supporting electrolyte) at an applied potential of ?0.2 V (vs. SCE). The response current was proportional to the concentration of H₂O₂ in the range of 1.0×10^?5 mol/L to 2.5×10^?4 mol/L with the detection limit of 2.2×10^?6 mol/L at a signal to noise ratio 3.     

Catalysis‐Electrochemical Detection of Horseradish Peroxidase at Zeptomole Level in Capillary Zone Electrophoresis

Capillary zone electrophoresis with catalysis‐electrochemical detection has been developed and applied to determining horseradish peroxidase (HRP) at zeptomole levels. In this method, an on‐line enzyme catalysis reactor with a reaction capillary was designed. Isoenzymes of HRP were separated by capillary zone electrophoresis, and then they catalyzed the enzyme substrate 3,3′,5,5′‐tetramethylbenzide (TMB(Red)) and H₂O₂ in the reaction capillary. The reaction product, TMB(Ox), could be determined using amperometric detection on a carbon fiber microdisk bundle electrode at the outlet of the reaction capillary. Because of enzyme amplification, a significant amount of TMB(Ox) could be produced for detection. Therefore, the limit of detection (LOD) of HRP is very low. The optimum conditions of the method are 1.5×10^?2 mol/L borate (pH 7.4) for the run buffer, 2×10^?3 mol/L for the concentration of H₂O₂, 2×10^?4 mol/L TMB(Red)+2.0×10^?2 mol/L citrate‐phosphate (pH 5.0) for the substrate solution, 40 cm for the liquid pressure height, 20 kV for the separation voltage, 100 mV for the detection potential. HRP could be measured with a detection limit of 4.8×10^?12 mol/L or 47.5 zmol (S/N=3). The linear range is from 2.40×10^?11 to 2.40×10^?8 mol/L. Using this method, commercial HRP was measured at zeptomole within ten minutes.     

One-step construction of an electrode modified with electrodeposited Au/SiO2 nanoparticles, and its application to the determination of NADH and ethanol

A new electrode was developed by one-step potentiostatic electrodeposition (at ?2.0 V for 20 s) of Au/SiO₂ nanoparticles on a glassy carbon electrode. The resulting electrode (nano-Au/SiO₂/GCE) was characterized by scanning electronic microscopy, X-ray photoelectron spectroscopy and electrochemical techniques. The electrochemical behavior of dihydronicotinamide adenine dinucleotide (NADH) at the nano-Au/SiO₂/GCE were thoroughly investigated. Compared to the unmodified electrode, the overpotential decreased by about 300 mV, and the current response significantly increased. These changes indicated that the modified electrode showed excellent catalytic activity in the oxidation of NADH. A linear relationship was obtained in the NADH concentration range from 1.0?×?10^?6 to 1.0?×?10^?4 mol?L^?1. In addition, amperometric sensing of ethanol at the nano-Au/SiO₂/GCE in combination with alcohol dehydrogenase and nicotinamide adenine dinucleotide was successfully demonstrated. A wide linear response was also found for ethanol in the range from 5.0?×?10^?5 to 1.0?×?10^?3 mol?L^?1 and 1.0?×?10^?3 to 1.0?×?10^?2 mol?L^?1, respectively. The method was successfully applied to determine ethanol in beer and biological samples.     

Determination of Albumin Using the Chemiluminescence of Tb3+/K2S2O8 System

A new chemiluminescence system of Tb³⁺/K₂S₂O₈ was developed for the determination of albumin. Some experimental conditions were examined and optimized. The linear ranges of the calibration curves are 5.0 × 10^?9–5.0 × 10^?6 mol/L for bovine serum albumin, 5.0 × 10^?8–1.0 × 10^?5 mol/L for human serum albumin and 2.5 × 10^?7–1.0 × 10^?5 mol/L for ovalbumin, and the corresponding detection limits are 1.9 × 10^?9 mol/L, 1.5 × 10^?8 mol/L, and 1.5 × 10^?7 mol/L, respectively. The method was applied to the determination of albumin in human serum samples, and the results were in agreement with those obtained by the bromcresol green method. The relative errors for the analytical results were from ?2.0% to 4.3%.     

Catalytic Adsorptive Stripping Voltammetry of Germanium(IV) in the Presence of Gallic Acid and Vanadium(IV)‐EDTA

A highly sensitive and selective catalytic adsorptive cathodic striping procedure for the determination of trace germanium is presented. The method is based on adsorptive accumulation of the Ge(IV)‐gallic acid (GA) complex onto a hanging mercury drop electrode, followed by reduction of the adsorbed species. The reduction current is enhanced catalytically by addition of vanadium(IV)‐EDTA. The optimal experimental conditions include the use of 0.03 mol/L HClO₄ (pH1.6), 6.0×10^?3 mol/L GA, 3.0×10^?3 mol/L V(IV), 4.0×10^?3 mol/L EDTA, an accumulation potential of ?0.10 V(vs. Ag/AgCl), an accumulation time of 120 s and a differential pulse potential scan mode. The peak current is proportional to the concentration of Ge(IV) over the range of 3.0×10^?11 to 1.0×10^?8 mol/L and the detection limit is 2×10^?11 mol/L for a 120 s adsorption time. The relative standard deviation at 5.0×10^?10 mol/L level is 3.1%. No serious interferences were found. The method was applied to the determination of germanium in ore, mineral water and vegetable samples with satisfactory results.     

Adsorptive Voltammetric Measurement of Trace Level of Iron(III) with 4–(2–Pyridylazo) Resorcin

Abstract

The polarographic behavior of the complex of iron–4– (2–pyridylazo) resorcin(PAR) was studied. In HAc– NaAc– EDTA buffer solution, the complex can be adsorped on a hanging mercury drop electrode giving a sensitive adsorptive complex reduction peak with a peak potential at -0.36V(vs. SCE). Optimum experimental conditions were found by the use of 0.08mol/L HAc, 0.06mol/L NaAc, 5.0 × 10^?3mol/L EDTA and 1.0 × 10^?5mol/L PAR. With preconcentration for 60s, the derivative peak height of the complex compound is linearly proportional to the concentration for Fe in the range from 1.0 × 10^?9mol/L to 1.0 × 10^?7mol/L. For a 2–min pre–concentration time, the detection limit found was 2.0 × 10^?10mol/L. This method has high sensitivity and selectivity. It has been applied to the determination of trace iron in food and water samples without any pre–separation step.     

Simultaneous Determination of Dopamine and Ascorbic Acid Using the Nano‐Gold Self‐Assembled Glassy Carbon Electrode

Electrochemical behavior of dopamine (DA) was investigated at the gold nanoparticles self‐assembled glassy carbon electrode (GNP/LC/GCE), which was fabricated by self‐assembling gold nanoparticles on the surface of L ‐cysteine (LC) modified glassy carbon electrode (GCE) via successive cyclic voltammetry (CV). A pair of well‐defined redox peaks of DA on the GNP/LC/GCE was obtained at E_pa=0.197 V and E_pc=0.146 V, respectively. And the peak separation between DA and AA is about 0.2 V, which is enough for simultaneous determination of DA and AA. The peak currents of DA and AA were proportional with their concentrations in the range of 6.0×10^?8–8.5×10^?5 mol L^?1 and 1.0×10^?6–2.5×10^?3 mol L^?1, with the detection limit of 2.0×10^?8 mol L^?1 and 3.0×10^?7 mol L^?1 (S/N=3), respectively. The modified electrode exhibits an excellent reproducibility, sensibility and stability for simultaneous determination of DA and AA in human serum with satisfactory result.     

Electrochemical Behavior and Determination of L‐Tyrosine at Single‐walled Carbon Nanotubes Modified Glassy Carbon Electrode

Based on single‐walled carbon nanotubes (SWCNTs) modified glassy carbon electrode (GCE/SWCNTs), a novel method was presented for the determination of L ‐tyrosine. The GCE/SWCNTs exhibited remarkable catalytic and enhanced effects on the oxidation of L ‐tyrosine. In 0.10 mol/L citric acid‐sodium citrate buffer solution, the oxidation potential of L ‐tyrosine shifted negatively from +1.23 V at bare GCE to +0.76 V at GCE/SWCNTs. Under the optimized experimental conditions, the linear range of the modified electrode to the concentration of L ‐tyrosine was 5.0×10^?6–2.0×10^?5 mol/L (R₁=0.9952) and 2.7×10^?5–2.6×10^?4 mol/L (R₂=0.9998) with a detection limit of 9.3×10^?8 mol/L. The kinetic parameters such as α (charge transfer coefficient) and D (diffusion coefficient) were evaluated to be 0.66, 9.82×10^?5 cm² s^?1, respectively. And the electrochemical mechanism of L ‐tyrosine was also discussed.     

Label-Free Detection of DNA Hybridization Based on MnO2 Nanoparticles

Abstract

Nano-MnO₂/chitosan composite film modified glassy carbon electrode (MnO₂/CHIT/GCE) was fabricated and a DNA probe was immobilized on the electrode surface. The immobilization and hybridization events of DNA were characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The EIS was applied to the label-free detection of the target DNA. The human immunodeficiency virus (HIV) gene fragment was successfully detected by this DNA electrochemical sensor. The dynamic detection range was from 2.0 × 10^?11 to 2.0 × 10^?6 mol/L, with a detection limit of 1.0 × 10^?12 mol/L.     

多臂碳纳米管/Nafion复合材料修饰玻碳电极测定痕量的铅离子

A composite material of nitric acid oxidized multiwalled carbon nanotube （MWNT） and Nation was prepared. Such composite was modified on a glassy carbon electrode to determine trace of lead by differential pulsed voltammetry. In pH=6.47 NaNO3 solution, Pb^2＋ ions were accumulated on the modified electrode at -0.4 V. Compared with a bare and a Nation film coated electrode, the composite coated GC electrode can reduce the accumulating potential and eliminate the toxic character of mercury. The calibration plots were linear at low concentration of 5.0× 10^-9-2.0× 10^-8 mol/L and high concentration of 2.5× 10^-8-5.0× 10^-6 mol/L. The performances characteristics indicate that the electrode can be used to determine trace Pb^2＋ ions.     

Electrochemical Enzyme‐Linked Immunoassay for the Determination of Estriol Using Methyl Red as Substrate

Abstract

A new electrochemical substrate for horseradish peroxidase, methyl red, is reported. In this reaction system, horseradish peroxidase can catalyze the redox reaction of methyl red and H₂O₂. Methyl red exhibits a sensitive voltammetric peak at?0.51 V vs. Ag/AgCl reference electrode, the decrease of the peak current of methyl red is in proportion to the concentration of horseradish peroxidase (HRP). The linear range for determination of horseradish peroxidase is 5.0×10^?8～5.0×10^?7 g mL^?1 and the detection limit is 1.8×10^?8 g mL^?1. The relative standard deviation is 3.3% when 2.0×10^?7 g mL^?1 HRP was sequentially determined 11 times. A voltammetric enzyme‐linked immunoassay method for the determination of estriol was developed, based on this electrochemical system. The linear range for determination of estriol is 1.0～1000.0 ng mL^?1, and the detection limit is 0.33 ng mL^?1. The relative standard deviation for 11 parallel determinations with 200 ng mL^?1 estriol is 4.8%. Some pregnancy serum samples were analyzed with satisfactory results.     

Sensitive and Simple Electrochemical Detection of Lead(II) with Carbon Ionic Liquid Electrode

In this paper a carbon ionic liquid electrode (CILE) was fabricated by using ionic liquid 1‐ethyl‐3‐methylimidazolium ethylsulphate ([EMIM]EtOSO₃) as the modifier and further used as the working electrode for the sensitive anodic stripping voltammetric detection of Pb²⁺. The characteristics of the CILE were investigated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). In pH 4.5 NaAc‐HAc buffer Pb²⁺ was accumulated on the surface of CILE due to the extraction effect of IL and reduced at a negative potential (‐1.20 V). Then the reduced Pb was oxidized by differential pulse anodic stripping voltammetry with an obvious stripping peak appeared at ?0.67 V. Under the optimal conditions Pb²⁺ could be detected in the concentration range from 1.0 × 10^?8 mol/L to 1.0 × 10^?6 mol/L with the linear regression equation as I_p(μA) = ?0.103 C (μmol/L) + 0.0376 (γ = 0.999) and the detection limit as 3.0 × l0^?9 mol/L (3σ). Interferences from other metal ions were investigated and Cd²⁺ could be simultaneously detected in the mixture solution. The proposed method was further applied to the trace levels of Pb²⁺ detection in water samples with satisfactory results.     

Tubular potentiometric detector used to determine As(V) in sediment extracts by flow injection

The construction and evaluation of a tubular potentiometric detector sensitive to As(V) ions is described. This electrode, with no inner reference solution, is comprised of a FeOOH–SiO₂–graphite composite agglutinated with an epoxy resin. For As(V) ion concentrations in the range 1.0?×?10^?5 to 1.0?×?10^?1?mol?L^?1, the sensor is used as the selective electrode in an FIA system along with a commercial Ag/AgCl reference electrode. In optimal conditions, the practical limit of detection is 4?×?10^?6?mol?L^?1 and a sampling rate of 40?h^?1 can be achieved. The system was applied to estimate As(V) levels in sediments of a drinking water distributor in Zimapán (Mexico), an area known to be polluted with this element. The As(V) concentrations detected in the different extracts of sediments generated by the sequential modified BCR three-step extraction procedure (BCR-SEP) were comparable to those obtained by electrothermal atomic absorption spectroscopy (ET-AAS).     

Thiol‐Functionalized Silica Thin Film Modified Electrode in Determination of Mercury Ions in Natural Water

The use of a thin thiol‐functionalized silica film modified glassy carbon electrode in the determination of Hg(II) ions in a natural water sample is described. A typical measurement involves two successive steps: a glassy carbon electrode coated with a thin mesoporous silica film containing 10% of mercaptopropyl groups, according to the MPTMS/TEOS ratio in the starting sol‐gel, was first immersed into the accumulation medium for 15 min, then removed, and finally transferred into a detection solution containing KCl 1.0 mol L^?1 where detection was performed by anodic stripping voltammetry. In this medium the previously accumulated Hg²⁺ species complexed by the thiol groups in an open circuit preconcentration step is then directly reduced at ?0.6 V during 60 s prior to be quantified by a differential pulse anodic scan from ?0.6 to 0.3 V (vs. Ag/AgCl). A stripping peak appeared at about ?0.01 V, which is directly proportional to the quantity of the analyte previously accumulated into the film. The best results were obtained under the following conditions: 100 mV pulse amplitude and 10 mV s^?1 scan rate in 1.0 mol L^?1 KCl solution pH 2.0. Using such parameters a linear dynamic range from 1.00 to 10.0×10^?8 mol L^?1 Hg(II) was observed with a limit of detection of 4.3 nmol L^?1 for an accumulation time of 15 min. Hg(II) spiked in a natural water sample was determined between 97.0 and 101.4% mean recovery at 10^?8 mol L^?1 level. The results indicate that this electrode is sensitive and selective for the Hg(II)determination.     

Flow injection determination of hydrogen peroxide using diperiodatoargentate- and diperiodatonickelate-luminol chemiluminescence

A novel chemiluminescence (CL) method for the determination of hydrogen peroxide is described. Method is based on the transition metals in highest oxidation state complex, which include diperiodatoargentate (DPA) and diperiodatonickelate (DPN) and show excellent sensitisation on the luminol-H₂O₂ CL reaction with low luminol concentration in alkaline medium. In particular, the sensitiser which was previously reported (such as Co²⁺, Cu²⁺, Ni²⁺, Mn²⁺, Fe³⁺, Cr³⁺, KIO₄, K₃Fe(CN)₆ etc.) to be unobserved CL due to poor sensitisation with such low concentration of luminol which makes the method hold high selectivity. Based on this observation, the detection limits were 6.5?×?10^?9?mol?L^?1 and 1.1?×?10^?8?mol?L^?1 hydrogen peroxide for the DPN- and DPA-luminol CL systems, respectively. The relative CL intensity was linear with the hydrogen peroxide concentration in the range of 2.0?×?10^?8–6.0?×?10^?6?mol?L^?1 and 4.0?×?10^?8–4.0?×?10^?6?mol?L^?1 for the DPN- and DPA-luminol CL systems, respectively. The proposed method had good reproducibility with a relative standard deviation of 3.4% (8.0?×?10^?7?mol?L^?1, n?=?7) and 1.0% (2.0?×?10^?6?mol?L^?1, n?=?7) for the DPN- and DPA-luminol CL systems, respectively. A satisfactory result has been gained for the determination of H₂O₂ in rainwater and artificial lake water by use of the proposed method.     

Detection and Quantification of Sulfonamide Antibiotic Residues in Milk Using Scanning Electrochemical Microscopy

The use of scanning electrochemical microscopy (SECM) for the qualitative and quantitative determination of sulfapyridine (SPY) in milk is described. A direct competitive immunoassay was performed involving an antibiotic horseradish peroxidase (HRP)‐labeled analog and using selective capture antibodies immobilized on the surface of Protein G‐modified glassy carbon plates. SECM detection was accomplished by means of the sample generator/tip collector (GC) mode involving the reduction of benzoquinone (BQ) generated upon the HRP‐catalyzed oxidation of hydroquinone (HQ) at the modified substrate surface in the presence of H₂O₂. The detection limit for SPY in milk samples was as low as 0.13 ng mL^?1.     

A New Fluorimetric Reagent for Determination of Trace Amounts of Europium

ＩｎｔｒｏｄｕｃｔｉｏｎＴｈｅｃｈｅｍｉｃａｌｐｒｏｐｅｒｔｉｅｓｏｆｒａｒｅ ｅａｒｔｈｅｌｅｍｅｎｔｓａｒｅｖｅｒｙｓｉｍｉｌａｒ ,ｃｏｎｓｅｑｕｅｎｔｌｙ ,ｉｔｉｓｄｉｆｆｉｃｕｌｔｔｏｄｅｔｅｃｔａｎｉｎ ｄｉｖｉｄｕａｌｉｏｎｉｎｔｈｅｉｒｍｉｘｔｕｒｅｓｏｗｉｎｇｔｏｔｈｅｉｎｔｅｒｆｅｒｅｎｃｅｏｆｏｔｈｅｒｒａｒｅ ｅａｒｔｈｅｌｅｍｅｎｔｓ .Ｄｕｅｔｏａｈｉｇｈｅｒｓｅｎｓｉｔｉｖｉｔｙａｎｄｓｅｌｅｃｔｉｖｉｔｙ ,ｆｌｕｏｒｉｍｅｔｒｉｃｍｅｔｈｏｄｓｏｆｒａｒｅ ｅａｒｔｈｅｌ…     

Study on Diffusion Mechanisms and Determination of Dihydroxybenzene Isomers at the Pre‐anodized Inlaying Ultrathin Carbon Paste Electrode

In this paper, nichrome was adopted as a substrate, to fabricate the pre‐anodized inlaying ultrathin carbon paste electrode (PAIUCPE). The electrochemical behaviors and diffusion mechanisms of three dihydroxybenzene isomers at the electrode were carefully investigated. The effect of pH on oxidation peak current was also detailedly explained. The results were shown that oxidation peak current not only related to the reaction of electroactive materials at the working electrode, but also depended on the reaction variable of reduction at the auxiliary electrode. The oxidation peaks of hydroquinone (HQ), catechol (CC) and resorcinol (RC) located at 0.181 V, 0.288 V and 0.736 V. For CC, RC and HQ, the oxidation peak currents were linear to the concentrations at the range of 5.0 × 10^?6～5.0 × 10^?4 mol/L, 3.0 × 10^?6～5.0 × 10^?4 mol/L and 4.0 × 10^?6～4.0 × 10^?4 mol/L with the detection limits of 2.0 × 10^?7 mol/L, 1.2 × 10^?7 mol/L and 1.2 × 10^?7 mol/L, respectively. The proposed method was successfully applied in the simultaneous determination of dihydroxybenzene isomers in artificial sewage samples with satisfactory results.     

Electrochemical Detection of Methimazole by Capillary Electrophoresis at a Carbon Fiber Microdisk Electrode

We developed a sensitive, simple and low cost method to determine methimazole based on capillary electrophoresis with electrochemical detection (CE‐EC) at a carbon fiber microdisk electrode (CFE). We investigated the effects of detection potential, the concentration and pH value of the phosphate buffer, and injection time as well as separation voltage on the detection of methimazole. Under the optimized conditions: the detection potential at 1.30 V, 10 mmol/L phosphate buffer (pH 7.0), injection time 30 s at a height of 20 centimeter and separation voltage at 15 kV, the linear range was obtained from 1.0×10^?7 to 2.0×10^?4 mol/L, covering 3 orders of magnitude with a correlation coefficient of 0.9995. The LOD (S/N=3) obtained was 5.0×10^?8 mol/L. The RSD of migration time and peak current for 2.0×10^?4 mol/L methimazole was 1.04% and 1.54% (n=10), respectively. The method was also used to analyze methimazole tablets and human urine sample.     

Anodic Stripping Voltammetric Determination of Lead（Ⅱ） Using Glassy Carbon Electrode Modified with Novel Calix[4] arene

A new glassy carbon electrode modified with novel calix[4]‐arene derivative was prepared and then applied to the selective recognition of lead ion in aqueous media by cyclic and square wave voltammetry. A new anodic stripping peak at ? 0.92 V (vs. Ag/Ag⁺) in square wave voltammogram can be obtained by scanning the potential from ? 1.5 to ? 0.6 V, of which the peak current is proportional to the concentration of Pb²⁺. The modified electrode in 0.1 mol/L HNO₃ solution showed a linear voltammetric response in the range of 2.0 × 10–⁸–1.0 × 10–⁶ mol/L and a detection limit of 6.1 × 10–⁹ mol/L. In the modified glassy carbon electrode no significant interference occurred from alkali, alkaline and transition metal ions except Hg²⁺, Ag⁺ and Cu²⁺ ions, which can be eliminated by the addition of KSCN. The proposed method was successfully applied to determine lead in aqueous samples.