Electrocatalytic Oxidation and Determination of Norepinephrine at Poly(Cresol Red) Modified Glassy Carbon Electrode

A glassy carbon electrode (GCE) was modified with electropolymerized films of cresol red in pH 5.6 phosphate buffer solution (PBS) by cyclic voltammetry (CV). The modified electrode shows an excellent electrocatalytic effect on the oxidation of norepinephrine (NE). The peak current increases linearly with the concentration of NE in the range of 3×10^?6–3×10^?5 M by the differential pulse voltammetry. The detection limit was 2×10^?7 M. The modified electrode can also separate the electrochemical responses of norepinephrine and ascorbic acid (AA). The separation between the anodic peak potentials of NE and AA was 190 mV by the cyclic voltammetry. And the responses to NE and AA at the modified electrode were relatively independent.     

多巴胺在聚铬黑T修饰玻碳电极上的电化学行为及其测定

制备了聚铬黑T修饰玻碳电极,研究了多巴胺(DA)在该修饰电极上的电化学行为。实验结果表明,在pH 4.0磷酸缓冲溶液中,聚铬黑T薄膜对多巴胺的电化学氧化具有明显的催化作用。此外,实验中观察到铬黑T膜能分离检测DA、抗坏血酸(AA)和尿酸(UA)三者的电化响应,DA与AA和UA之间的电位差达到210 mV和170 mV。利用差示脉冲伏安法(DPV)测定DA,其线性范围为0.1~200μmol/L,检出限为0.02μmol/L。该法已成功用于DA注射剂的含量分析,结果令人满意。     

阿魏酸聚合修饰玻碳电极的制备及其对NADH的催化氧化

研究了阿魏酸修饰电极的制备、性质及对NADH的电催化作用.该电极在0.1mol/L磷酸缓冲溶液(pH=6.60)中,于-0.1～+0.50V(vs.Ag/AgCl)电位范围内呈现一对氧化还原峰,其式量电位E₀为+0.188V(vs.Ag/AgCl),且E₀随pH增加而负向移动.电子转移系数为0.496,表观电极反应速率常数(ks)为6.6s^-1.电极反应的电子数为1且有1个质子参与.该修饰电极对NADH氧化具有很好的催化作用.在NADH存在下,电极过程由扩散控制,扩散系数为1.76×10^-6cm²/s.NADH浓度在0.01～5.0mmol/L范围内与峰电流呈现良好的线性关系.通过计时安培法测得催化速率常数为6.82×10³mol^-1·L·s^-1.     

抗坏血酸在聚对羟基苯甲酸修饰玻碳电极上的催化电氧化行为

通过循环伏安(CV)制备了聚对羟基苯甲酸(poly-PHB)修饰的玻碳电极. 考察了电极对抗坏血酸(AA)电氧化的催化性能. 结果显示,聚对羟基苯甲酸修饰玻碳电极对AA氧化有很好的电催化作用. 在修饰电极上产生的峰电流比在未修饰电极上产生的氧化峰电流大4倍,氧化峰电位负移205 mV. 氧化峰电流与AA浓度在2.6×10-5～3.68 ×10-4 mol/L范围内呈线性关系,相关系数为0.998 4,检测限为5×10-6 mol/L(S/N=3). 在AA与多巴胺(DA)共存的体系中,能排除DA对抗坏血酸测定的干扰.     

Determination of Dopamine in the Presence of Ascorbic Acid Using a Poly(Amidosulfonic Acid) Modified Glassy Carbon Electrode

A glassy carbon electrode (GCE) was modified with electropolymerized films of amidosulfonic acid in pH 7.0 phosphate buffer solution (PBS) by cyclic voltammetry (CV). The modified electrode showed an excellent electrocatalytical effect on the oxidation of dopamine (DA). In pH 7.0 PBS, the anodic peak current increased linearly with the concentration of DA in the range of 5.0×10^–7 1.0×10^–4moldm^–3, with a correlation coefficient of 0.9932, and a detection limit (S/N=3) of 1.0× 10^–7moldm^–3. The relative standard deviation of 10 successive scans was 2.5% for 1.0×10^–6moldm^–3 DA. The interference of ascorbic acid (AA) with the determination of DA could be eliminated because of the very distinct attracting interaction between DA cations and the negatively poly(amidosulfonic acid) film in pH 7.0 PBS. The proposed method exhibited good recovery and reproducibility.     

Electrochemical Preparation of Poly(Malachite Green) Film Modified Nafion‐Coated Glassy Carbon Electrode and Its Electrocatalytic Behavior Towards NADH,Dopamine and Ascorbic Acid

Poly(malachite green) film modified Nafion‐coated glassy carbon electrodes have been prepared by potentiodynamic cycling in malachite green solution. The pH of polymerisation solution has only minor effect on film formation. Electrochemical quartz crystal microbalance (EQCM) was used to monitor the growth of the poly(malachite green) film. Cyclic voltammogram of the poly(malachite green) film shows a redox couple with well‐defined peaks. The redox response of the modified electrode was found to be depending on the pH of the contacting solution. The peak potentials were shifted to a less positive region with increasing pH and the dependence of the peak potential was found to be 56 mV per pH unit. The electrocatalytic behavior of poly(malachite green) film modified Nafion‐coated glassy carbon electrodes was tested towards oxidation of NADH, dopamine, and ascorbic acid. The oxidation of dopamine and ascorbic acid occurred at less positive potential on poly(malachite green) film compared to bare glassy carbon electrode. In the case of NADH, the overpotential was reduced substantially on modified electrode. Finally, the feasibility of utilizing poly(malachite green) film electrode in analytical estimation of ascorbic acid was demonstrated in flow injection analysis.     

多壁碳纳米管-Nafion化学修饰电极在高浓度抗坏血酸和尿酸体系中选择性测定多巴胺

多巴胺是人体内一种重要的神经传递物质 ,它参与许多生命过程[1] .因此 ,测定体内多巴胺的浓度十分重要 .多巴胺的电化学分析方法已有不少报道 [2 ,3 ] .然而 ,共存的抗坏血酸和尿酸的电化学性质与多巴胺相似 ,对多巴胺的测定会产生严重干扰 .因此建立一种选择性测定多巴胺的高灵敏度的分析方法就显得尤为重要 .碳纳米管是一种新型的纳米材料 [4 ] ,它的出现引起了广泛的研究兴趣 [5,6] .由于其性质稳定 ,不溶于水及一般的有机溶剂 ,因此限制了其在电分析方面的应用 .本文将多壁碳纳米管分散在 Nafion的无水乙醇中 ,得到了一种均匀的多壁碳…     

抗坏血酸在多壁碳纳米管修饰玻碳电极上的催化氧化

多壁碳纳米管;抗坏血酸;修饰电极;电催化;伏安法     

碳纳米管修饰电极对多巴胺和抗坏血酸的电催化氧化

研究了碳纳米管修饰玻碳电极 (NTCME)的制备方法及对多巴胺 (DA)和抗坏血酸 (AA)的电催化氧化作用。在磷酸盐缓冲溶液 (PBSpH 7.4)中 ,以NTCME为工作电极时 ,DA与AA的氧化电位分别为 0 .2 6和 0 .0 1V(vs.SCE) ,比在裸玻碳电极 (GC)上分别降低了 0 .0 7和 0 .6 2V。NTCME能消除DA与AA共存时测定的相互干扰。利用二阶导数卷积伏安法测定 ,DA与AA分别在 2 .0 0× 10 - 6～ 3.84× 10 - 4 和 7.99× 10 - 5～ 3.6 6× 10 - 3 mol L浓度范围内 ,峰高与浓度呈线性关系 ;检出限分别为 1.90× 10 - 7和 5 .96× 10 - 5mol L。     

Determination of Uric Acid in the Presence of Ascorbic Acid Using Poly(3,4‐ethylenedioxythiophene)‐Modified Electrodes

A poly(3,4‐ethylenedioxythiophene) (PEDOT) modified glassy carbon electrode (GCE) was used to determine uric acid in the presence of ascorbic acid at physiological pH facilitating a peak potential separation of ascorbic acid and uric acid oxidation (ca. 365 mV), which is the largest value reported so far in the literature. Also, an analytical protocol involving differential pulse voltammetry has been developed using a microchip electrode for the determination of uric acid in the concentration range of 1 to 20 μM in presence of excess of ascorbic acid.     

聚伊文思蓝修饰电极对多巴胺和抗坏血酸的电分离及同时测定

研究多巴胺(DA)和抗坏血酸(AA)在聚伊文思蓝(Evans Blue)修饰电极上的伏安行为,建立差示脉冲伏安测定法.在pH4.5磷酸盐缓冲液中,聚伊文思蓝修饰电极对DA和AA有显著的增敏和电分离作用.DA和AA氧化峰电流与浓度分别在1.0×10-6~3.0×10-5mol/L和5.0×10-6~1.05×10-4mol/L范围内呈良好的线性关系,检测限分别为2.5×10-7mol/L和3.0×10-7mol/L.当DA与AA共存时,由该修饰电极检测的二者氧化峰电位差达184 mV,故可同时测定DA和AA,并有效消除其它组分对DA测定的干扰,已用于实际样品中DA和AA含量的测定,结果令人满意.     

Silver Doped Poly(L‐valine) Modified Glassy Carbon Electrode for the Simultaneous Determination of Uric Acid,Ascorbic Acid and Dopamine

In this paper, a silver doped poly(L ‐valine) (Ag‐PLV) modified glassy carbon electrode (GCE) was fabricated through electrochemical immobilization and was used to electrochemically detect uric acid (UA), dopamine (DA) and ascorbic acid (AA) by linear sweep voltammetry. In pH 4.0 PBS, at a scan rate of 100 mV/s, the modified electrode gave three separated oxidation peaks at 591 mV, 399 mV and 161 mV for UA, DA and AA, respectively. The peak potential differences were 238 mV and 192 mV. The electrochemical behaviors of them at the modified electrode were explored in detail with cyclic voltammetry. Under the optimum conditions, the linear ranges were 3.0×10^?7 to 1.0×10^?5 M for UA, 5.0×10^?7 to 1.0×10^?5 M for DA and 1.0×10^?5 to 1.0×10^?3 M for AA, respectively. The method was successfully applied for simultaneous determination of UA, DA and AA in human urine samples.     

Electropreparation of Poly(benzophenone‐4) Film Modified Electrode and Its Electrocatalytic Behavior Towards Dopamine,Ascorbic Acid and Nitrite

The oxidation of benzophenone‐4 (2‐hydroxy‐4‐methoxybenzophenone‐5‐sulfonic acid) at glassy carbon electrode gives rise to stable redox active electropolymerized film during repetitive potential cycling between 0 to 1.3 V (Ag/AgCl). Cyclic voltammogram of poly(benzophenone‐4) film shows a redox couple with well‐defined peaks. The redox response of the modified electrode was found to be depending on the pH of the contacting solution. The peak potentials were shifted to a less positive region with increasing pH and the dependence of the peak potential was found to be 51 mV/pH. The electrocatalytic behavior of poly(benzophenone‐4) film modified electrode towards oxidation of dopamine, ascorbic acid and reduction of nitrite was investigated. The oxidation of dopamine and ascorbic acid occurred at less positive potential on poly(benzophenone‐4) film compared to bare glassy carbon electrode. For dopamine, the overpotential was reduced about 180 mV. Feasibility of utilizing poly(benzophenone‐4) film coated electrode in analytical estimation of dopamine, ascorbic acid and nitrite was also demonstrated.     

Poly(pyridine‐3‐boronic acid)/Multiwalled Carbon Nanotubes Modified Glassy Carbon Electrodes for Simultaneous Determination of Ascorbic Acid, 3,4‐Dihydroxyphenylacetic Acid and Uric Acid

Poly(pyridine‐3‐boronic acid) (PPBA)/multiwalled carbon nanotubes (MWCNTs) composite modified glassy carbon electrode (GCE) was used for the simultaneous determination of ascorbic acid (AA), 3,4‐dihydroxyphenylacetic acid (DOPAC) and uric acid (UA). The anodic peaks for AA, DOPAC and UA at the PPBA/MWCNTs/GCE were well resolved in phosphate buffer solution (pH 7.4). The electrooxidation of AA, DOPAC and UA in the mixture solution was investigated. The peak currents increase with their concentrations increasing. The detection limits (S/N=3) of AA, DOPAC and UA are 5 µM, 3 µM and 0.6 µM, respectively.     

聚氨基磺酸修饰玻碳电极在抗坏血酸共存时测定肾上腺素

研究了聚氨基磺酸修饰玻碳电极的制备及肾上腺素和抗坏血酸在此修饰电极上的电化学行为。在磷酸盐缓冲液pH为 7. 0的条件下,肾上腺素在修饰电极上呈现 2个氧化峰和 1个还原峰。其峰电位都随着pH值的增加而负移。当肾上腺素与抗坏血酸共存时,EP较正处氧化峰电位与AA氧化峰电位差达 190mV。肾上腺素氧化峰电流与其浓度在 1. 0×10-7 ~1. 0×10-4 mol/L的范围时呈良好的线性关系,其线性回归方程为ip(10μA) = 1. 455 + 0. 3765C(mol/L), 相关系数r=0. 9977,检出限为 1. 0×10-8 mol/L。实验结果表明:该修饰电极能同时测定肾上腺素和抗坏血酸; 100倍的马尿酸、半胱氨酸、柠檬酸不干扰测定。方法用于注射液中肾上腺素的检测,结果令人满意。     

羧基化碳纳米管嵌入石墨修饰电极对多巴胺和抗坏血酸的电催化

采用涂层和嵌入修饰法 ,将羧基化多层碳纳米管制成两种修饰电极。以多巴胺 (DA)和抗坏血酸(AA)为模型化合物 ,研究了两种修饰电极对DA和AA共存时的电催化作用。结果表明 :嵌入的方式比涂层的方式显示了更多的优点。嵌入修饰电极不仅使峰电流增加 ,并且使两者共存时的氧化峰位分离达 16 0mV ,同时 ,该电极对DA的响应灵敏于AA ,这有利于在大量的AA存在下实现对DA的测定。在 1× 10 - 3 mol/L的AA的存在下 ,还原电流的一阶导数与DA浓度在 5× 10 - 7～ 1× 10 - 4 mol/L范围内呈良好的线性关系 ;检测下限达 1× 10 - 7mol L。     

Electrocatalytic Oxidation of Acyclovir on Poly(p‐Aminobenzene Sulfonic Acid) Film Modified Glassy Carbon Electrode

Acyclovir is an antiviral effective drug active compound. A glassy carbon electrode (GCE) was modified with an electropolymerized film of p‐aminobenzene sulfonic acid (p‐ABSA) in phosphate buffer solution (PBS). The polymer film‐modified electrode was used to electrochemically detect acyclovir. Polymer film showed excellent electrocatalytic activity for the oxidation of acyclovir. The anodic peak potential value of the acyclovir at the poly(p‐ABSA) modified glassy carbon electrode was 950 mV obtained by DPV. A linear calibration curve for DPV analysis was constructed in the acyclovir concentration range 2×10^?7–9×10^?6 mol L^?1. Limit of detection (LOD) and limit of quantification (LOQ) were obtained as 5.57×10^?8 and 1.85×10^?7 mol L^?1 respectively. The proposed method exhibits good recovery and reproducibility.     

Selective Detection of Uric Acid in the Presence of Ascorbic Acid and Dopamine Using Polymerized Luminol Film Modified Glassy Carbon Electrode

Electrochemically polymerized luminol film on a glassy carbon electrode (GCE) surface has been used as a sensor for selective detection of uric acid (UA) in the presence of ascorbic acid (AA) and dopamine (DA). Cyclic voltammetry was used to evaluate the electrochemical properties of the poly(luminol) film modified electrode. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) have been used for surface characterizations. The bare GCE failed to distinguish the oxidation peaks of AA, DA and UA in phosphate buffer solution (pH 7.0), while the poly(luminol) modified electrode could separate them efficiently. In differential pulse voltammetric (DPV) measurements, the modified GCE could separate AA and DA signals from UA, allowing the selective determination of UA. Using DPV, the linear range (3.0×10^?5 to 1.0×10^?3 M) and the detection limit (2.0×10^?6 M) were estimated for measurement of UA in physiological condition. The applicability of the prepared electrode was demonstrated by measuring UA in human urine samples.     

Electrocatalytic Determination of Ascorbic Acid at the Surface of 2,7‐Bis(ferrocenyl ethyl)fluoren‐9‐one Modified Carbon Paste Electrode

A chemically modified carbon paste electrode with 2,7‐bis(ferrocenyl ethyl)fluoren‐9‐one (2,7‐BFEFMCPE) was employed to study the electrocatalytic oxidation of ascorbic acid in aqueous solution using cyclic voltammetry, differential pulse voltammetry and chronoamperometry. The diffusion coefficient (D=1.89×10^?5 cm² s^?1), and the kinetic parameter such as the electron transfer coefficient, α (=0.42) of ascorbic acid oxidation at the surface of 2,7‐BFEFMCPE was determined using electrochemical approaches. It has been found that under an optimum condition (pH 7.00), the oxidation of ascorbic acid at the surface of such an electrode occurs at a potential about 300 mV less positive than that of an unmodified carbon paste electrode. The catalytic oxidation peak currents show a linear dependence on the ascorbic acid concentration and linear analytical curves were obtained in the ranges of 8.0×10^?5 M–2.0×10^?3 M and 3.1×10^?5 M–3.3×10^?3 M of ascorbic acid with correlation coefficients of 0.9980 and 0.9976 in cyclic voltammetry and differential pulse voltammetry, respectively. The detection limits (2δ) were determined to be 2.9×10^?5 M and 9.0×10^?6 M with cyclic voltammetry and differential pulse voltammetry, respectively. This method was also examined for determination of ascorbic acid in pharmaceutical preparations.     

基于溶胶-凝胶普鲁士蓝膜修饰玻碳电极电催化氧化测定水果中抗坏血酸

制备了一种溶胶-凝胶普鲁士蓝膜修饰玻碳电极,研究了抗坏血酸在该电极上的电催化氧化作用,建立了测定抗坏血酸的方法。在磷酸缓冲溶液(pH 5.0)中,在2.5×10-5-3.2×10-3mol.L-1范围内,抗坏血酸的浓度与氧化峰电流呈线性关系,相关系数为0.999 5,检出限为7×10-6mol.L-1。该修饰电极具有制备简单、灵敏度高、响应速度快、稳定性和重现性好等特点。方法已用于水果中抗坏血酸的测定,所得结果与药典法测得结果一致。