Ultraselective and Sensitive Determination of Cr(VI) in the Presence of a High Excess of Cr(III) in Natural Waters with a Complicated Matrix

In the present work, the catalytic adsorptive stripping voltammetric procedure for trace determination of Cr(VI) in the presence of a high excess of Cr(III) in natural waters with a complicated matrix has been developed. The influence from potentially interfering substances such as organic matter was successfully eliminated by exploiting adsorptive properties of polymeric resin. The detection limit estimated from 3 times the standard deviation for a low Cr(VI) concentration in the simultaneous presence of a 2×10³ fold excess of Cr(III), 50 mg L^?1 surfactants, 50 mg L^?1 humic substances and the accumulation time of 30 s was about 5.3×10^?10 mol L^?1.     

Speciation Analysis of Chromium by Adsorptive Stripping Voltammetry in Tap and River Water Samples

An adsorptive stripping voltammetric method for speciation analysis of chromium in natural water samples has been developed. Ethylenediaminetetraacetic acid (EDTA) and diethylenetriaminepentaacetic acid (DTPA) were used as complexing agents for Cr(III) present in the sample and formed as products of Cr(VI) reduction, respectively. Under optimum experimental conditions linear relations in the range from 1×10^?6 to 3×10^?5 mol L^?1 without accumulation and from 1×10^?9 to 1×10^?7 at 30 s accumulation time were obtained for Cr(III) and Cr(VI), respectively. For samples in which Cr(III) concentration is higher than 1×10^?6 mol L^?1 the Cr(III) and Cr(VI) were determined simultaneously in one voltammetric cell. For samples in which Cr(III) concentration is below 1×10^?6 mol L^?1 only Cr(VI) was selectively determined in the presence of Cr(III), which did not influence the Cr(VI) signal. The determination of Cr(III) and Cr(VI) was successful with the application of the proposed procedure in the presence of common foreign ions. The presented method was applied for the speciation of chromium in spiked tap and river water samples with satisfactory results.     

A catalytic adsorptive stripping voltammetric procedure for trace determination of Cr(VI) in natural samples containing high concentrations of humic substances

A simple and fast catalytic adsorptive stripping voltammetric procedure for trace determination of Cr(VI) in natural samples containing high concentrations of humic substances has been developed. The procedure for chromium determination in the presence of DTPA and nitrates was employed as the initial method. In order to enhance the selectivity vs. Cr(III) the measurements were performed at 40°C. Interference from dissolved organic matter such as humic and fulvic acids was drastically decreased by adding Amberlite XAD-7 resin to the voltammetric cell before the deaeration step. The whole procedure was applied to a single cell, which allowed monitoring of the voltammetric scan. Optimum conditions for removing humic and fulvic acids due to their adsorption on XAD-7 resin were evaluated. The use of XAD-7 resin also minimize interferences from various cationic, anionic, and nonionic surfactants. The calibration graph for Cr(VI) for an accumulation time of 30 s was linear in the range 5 × 10⁻¹⁰ to 5 × 10⁻⁸ mol L⁻¹. The relative standard deviation for determination of Cr(VI) at a concentration of 1 × 10⁻⁸ mol L⁻¹ was 3.5% (n = 5). The detection limit estimated from 3 times the standard deviation for low Cr(VI) concentrations and an accumulation time of 30 s was about 1.3 × 10⁻¹⁰ mol L⁻¹. The proposed method was successfully applied to Cr(VI) determination at trace levels in soil samples.     

Catalytic Adsorptive Stripping Voltammetric Procedure for Determination of Total Chromium in Environmental Materials

A sensitive catalytic adsorptive stripping voltammetric procedure for determination of traces of total chromium in environmental samples is reported. The method is based on the preconcentration of a Cr(III)? H₂DTPA complex by adsorption at the HMDE from an acetate buffer solution at the potential ?1.0 V vs. Ag/AgCl. Total chromium was determined as Cr(III) after reduction of Cr(VI) to Cr(III) by NaHSO₃. In order to stabilize the signal of Cr(III) the measurements were performed at 5 °C. The calibration graph for chromium for an accumulation time of 60 s was linear in the range from 5×10^?10 to 5×10^?8 mol L^?1. The relative standard deviation for a chromium concentration of 1×10^?8 mol L^?1 was 3.9% (n=5). The detection limit for accumulation time of 60 s was about 8×10^?11 mol L^?1. The validation of the procedure was performed by the analysis of the certified reference materials.     

Determination of trace amounts of chromium (VI) by flow injection analysis with chemiluminescence detection

A new sensitive chemiluminescence (CL) method combined with continuous flow injection analysis is described for the determination of Cr(VI). Strong CL signals were generated by Cr(VI)-catalysed oxidation of gallic acid in the presence of potassium permanganate and hydrogen peroxide. Effects of reagent concentrations, temperature, pH, flow rates, mixing coil length and mixing flow sequences on the chemiluminescence intensity were studied. Under the optimised experimental conditions, the relationship between the logarithm of concentration (log?C) of Cr(VI) and the logarithm of intensity (log?I) is linear over the range of 2?×?10^?11 – 5?×?10^?4?mol?L^?1, with the detection limit (3σ) of 4?×?10^?12?mol?L^?1. Relative standard deviation of ten measurements of 1?×?10^?9?mol?L^?1 Cr(VI) is 1.7%. This flow injection analysis (FIA) system proved to be able to analyse up to 40 samples h^?1. Effects of various interferences possibly present in the water samples were investigated. Most cations and anions, as well as organic compounds, did not interfere with the determination of Cr(VI) in water samples. The experimental results obtained for chromium in reference materials were also in good agreement with the certified values.     

Sensitive adsorptive stripping voltammetric method for direct determination of trace concentration of lead in the presence of cupferron in natural water samples

This paper reports the use of an adsorptive voltammetric technique for Pb(II) determination using cupferron as a selective complexing agent. After accumulation of the complex onto a hanging mercury drop electrode, the electrode potential was scanned with differential pulse modulation and the reduction current of lead was observed at about??0.5?V. Under optimum conditions (5?×?10^?4?mol?L^?1 cupferron concentration, 0.1?mol?L^?1 acetate buffer (pH 5.5), adsorption at??50?mV for 30?s) the detection limit was 5.1?×?10^?10?mol?L^?1. The relative standard deviation of five measurements for low lead concentration was 3.1%. The accuracy of the method was tested by analysing certified reference material (SPS-WW1 Waste Water). Finally, the method was successfully applied to the determination of Pb(II) in river water samples without any pretreatments.     

Simple and Highly Selective Catalytic Adsorptive Voltammetric Method for Cr(VI) Determination

A simple and highly selective and sensitive catalytic adsorptive stripping voltammetric procedure for determination of traces of Cr(VI) in the presence of a large excess of Cr(III) in environmental water samples is reported. To obtain a low detection limit the voltammetric procedure of chromium determination in the presence of DTPA and nitrate was exploited. For elimination of interference of Cr(III) ethylenediaminedisuccinic acid was used as a masking agent. At optimized conditions the calibration graph is linear from 2×10^?10 to 2×10^?8 mol L^?1 for accumulation time of 30 s. The validation of the procedure was performed by comparison of the results of analysis of river water samples with those obtained using other accepted voltammetric procedure.     

Fast Simultaneous Adsorptive Stripping Voltammetric Determination of Ni(II) and Co(II) at Lead Film Electrode Plated on Gold Substrate

A fast adsorptive stripping voltammetric procedure for simultaneous determination of Ni(II) and Co(II) in the presence of nioxime as a complexing agent at an in situ plated lead film electrode was described. The time of determination of these ions was shortened due to the application of gold as a substrate for lead film. At gold substrate lead film formation and accumulation of Ni(II) and Co(II) complexes with nioxime proceeds simultaneously. To obtain a stable signals for both ions a simple procedure of activation of the electrode was proposed. Calibration graphs for an accumulation time of 20 s were linear from 5×10^?9 to 1×10^?7 mol L^?1 and from 5×10^?10 to 1×10^?8 mol L^?1 for Ni(II) and Co(II), respectively. The procedure with the application of a lead film electrode on a gold substrate was validated in the course of Ni(II) and Co(II) determination in certified reference materials.     

Determination of Cr(VI) by Catalytic Adsorptive Stripping Voltammetry with Application of Nitrilotriacetic Acid as a Masking Agent

A selective and sensitive method for determination of traces of Cr(VI) in the presence of a large excess of Cr(III) by differential pulse catalytic adsorptive stripping voltammetry is presented. For minimization of Cr(III) interference nitrilotriacetic acid was used as a masking agent. The determinations were performed in a flow system. The calibration plot was linear from 1×10⁻¹⁰ to 1×10⁻⁸ mol L⁻¹ for accumulation time 60 s. The relative standard deviation for 3×10⁻⁹ mol L⁻¹ Cr(VI) was 4.1% (n=5). The detection limit for an accumulation time of 60 s was 4×10⁻¹¹ mol L⁻¹. The influence of common foreign ions is also presented. The performance of the method was verified by analysis of certified reference material for Cr(VI) and comparing the results of analyses of natural water samples with those obtained by another accepted electrochemical method.     

How to Determine Uranium Faster and Cheaper by Adsorptive Stripping Voltammetry in Water Samples Containing Surface Active Compounds

A modification of the voltammetric procedure for the determination of uranium in the presence of cupferron using hanging mercury drop electrode is presented. The pulsed potential accumulation was proposed for the minimization of interferences of surface active substances. The calibration plot for U(VI) in the presence of 2 ppm Tritonu X‐100 was linear from 1.7×10^?10 to 2.0×10^?8 mol L^?1 for an accumulation time of 60 s, with correlation coefficient of 0.996. The application of this method was tested in the determination of uranium in certified reference material NASS‐5 and river water samples.     

Simple and fast voltammetric procedure of U(VI) determination in the presence of high concentrations of surface active substances

In this work, a simple and fast procedure for elimination of interfering surface active substances and for U(VI) adsorptive stripping voltammetric determination was developed. The adsorption in the form of U(VI)-cupferron complexes was performed, because as it was proved before, U(VI) forms with cupferron stable complexes, which were employed in voltammetric procedures. The procedure is based on two steps: the first is an adsorption of surface active substances onto an Amberlite XAD-16 or XAD-7 resin and the second is a voltammetric determination of U(VI) with a pulsed potential of accumulation alternate –0.65–0.3 V with the frequency of 0.5 Hz and then the differential pulse voltammogram was recorded, whereas the potential was scanned from –0.65 to –1.2 V. The detection limit estimated from three times the standard deviation for a low U(VI) concentrations was equal to 1.7 × 10^?10 mol L^?1 (7.2 × 10^?8 g L^?1). The linear range of U(VI) was observed over the concentration range from 5.0 × 10^?10 mol L^?1 (2.1 × 10^?7 g L^?1) to 2.0 × 10^?8 mol L^?1 (8.5 × 10^?6 g L^?1) for an accumulation time of 60 s. The influence of different kinds of surfactants, such as non-ionic, cationic and anionic on the uranium voltammetric signal was studied. The results confirm the possibility of U(VI) determination in water samples containing high concentrations of surface active substances even up to 50 mg L^?1.     

Adsorptive stripping voltammetry of nickel at a bare glassy carbon electrode

A bare glassy carbon electrode is applied to nickel determination by adsorptive stripping voltammetry in the presence of dimethylglyoxime as a complexing agent. A procedure of nickel determination and electrode regeneration was proposed. The calibration graph for Ni(II) for an accumulation time of 120?s was linear from 2?×?10^?9 to 1?×?10^?7?mol?L^?1. The detection limit was 8.2?×?10^?10?mol?L^?1. The relative standard deviation for a solution containing 2?×?10^?8?mol?L^?1 of Ni(II) was 4.1%. The proposed procedure was applied for Ni(II) determination in certified water reference materials.     

Simultaneous Determination of Antimony(III) and Molybdenum(VI) by Adsorptive Stripping Voltammetry Using Quercetin as Complexing Agent

A sensitive and selective voltammetric method for simultaneous determination of Sb(III) and Mo(VI) using Quercetin (Q) as complexing agent is described. Optimal conditions were found to be: pH 3.7, C_Q=6.0 µmol L^?1 and E_acc=?0.10 V. The LOD (3σ) for Sb(III) are 0.076 and 0.040 µg L^?1, whereas for Mo(VI) are 0.086 and 0.048 µg L^?1 with t_acc of 60 and 120 s, respectively. The method was validated using synthetic sea water (ASTM D665) and was applied to the determination of Sb(III) and Mo(VI) in natural waters with satisfactory results.     

Lead Film Electrode Prepared with the Use of a Reversibly Deposited Mediator Metal in Adsorptive Stripping Voltammetry of Nickel

The paper presents the first report on application of a “hybrid” lead film electrode for the adsorptive stripping voltammetric determination of Ni(II) in the presence of nioxime as a complexing agent. The strategy to create a “hybrid” electrode is based on the combination of ex situ and in situ plating methods and the use of a reversibly deposited mediator metal (Zn) for the lead film formation. The surface morphology of a new sensor was characterized by atomic force microscopy. The detection limit for Ni(II) obtained at 120 s of accumulation time was 3.9×10^?11 mol L^?1. The proposed method was validated for the determination of nickel in water certified reference materials with good results.     

Separation and spectrophotometric determination of very low levels of Cr(VI) in water samples by novel pyridine-functionalized mesoporous silica

A modified SBA-15 mesoporous silica was developed, as an adsorbent, for the removal of Cr(VI) ions from natural-water samples. The effects of experimental parameters, including pH of solution, sample and eluent flow rate, the eluent composition, the eluent volume, and the effect of coexisting ions on the separation and determination of Cr(VI), were investigated. It was shown that Cr(VI) was selectively adsorbed from aqueous solution at pH 3, but Cr(III) could be adsorbed from solution at alkaline pH range. The retained Cr(VI) was eluted with 0.5?mol?L^?1 KCl solution in 0.1?mol?L^?1 Na₂CO₃ subsequently. Under the optimum conditions, the modified mesoporous silica (py-SBA-15) with a high pore diameter exhibited an adsorption capacity of 136?mg?g^?1 and a lower limit of detection than 2.3?µg?L^?1 by using diphenylcarbazide as a chromophorous reagent for the determination of Cr(VI) ions. A preconcentration factor as high as 200 was calculated for Cr(VI). The loaded py-SBA-15 can be reactivated with recovery of more than 98.5% over at least eight cycles. The relative standard deviation (RSD) for Cr(VI) ion recovery was less than 1.8%. Validation of the outlined method was performed by analysing a certified reference material (BCR 544). The proposed method was applied to determine Cr(VI) value in natural and waste water samples successfully.     

Determination of Trace of Cobalt in Complex Matrices by Adsorptive Stripping Voltammetry at a Lead Film Electrode

An adsorptive stripping voltammetric procedure for the determination of cobalt in a complex matrices at an in situ plated lead film electrode was described. The procedure exploits the enhancement effect of a cobalt peak observed in the system Co(II)–nioxime–piperazine‐1,4‐bis(2‐ethanesulfonic acid)–cetyltrimethylammonium bromide. The calibration graph was linear from 5×10^?10 to 2×10^?8 mol L^?1 and from 1×10^?10 to 1×10^?9 mol L^?1 for the accumulation times 120 and 600 s, respectively. The detection limit (based on the 3 σ criterion) for Co(II) following accumulation time of 600 s was 1.1×10^?11 mol L^?1. The interference of high concentrations of foreign ions and surfactants was studied.     

Voltammetric Determination of Proguanil in Malarone and Spiked Urine with a Renewable Silver Amalgam Film Electrode

Electrochemical properties of proguanil were investigated by a voltammetric method (SWV) using a renewable silver amalgam film electrode. The influence of buffer pH as well as potential amplitude, frequency, and step potential was studied. The repeatability, precision and recovery of the developed method were examined. The reduction peak current was used for proguanil voltammetric determination in the range 1×10^?7–6×10^?6 mol L^?1, LOD=2.9×10^?8 mol L^?1, LOQ=9.7×10^?8 mol L^?1. The standard addition method was used to determine proguanil in a commercial formulation (Malarone) and in spiked urine.     

Voltametric and Flow Injection Determination of Oxytetracycline Residues in Food Samples Using Carbon Fiber Microelectrodes

A voltammetric method for the determination of the antibiotic oxytetracycline (OTC) in food samples is reported. Carbon fiber microelectrodes (CFMEs), which allow voltammetric measurements to be performed in a small volume (1 mL) of the analyte extract from the samples, are employed. Repeatable electroanalytical responses were obtained with no need of applying cleaning treatments to the CFME. Under the optimized square‐wave conditions, a linear calibration plot for OTC was obtained in the 1.0×10^?6–1.0×10^?4 mol L^?1 range, with a detection limit of 2.9×10^?7 mol L^?1 (150 ng mL^?1) OTC. The determination of OTC by a flow‐injection method with amperometric detection using a homemade flow cell specially designed to work with CFMEs, was also evaluated using pure acetonitrile as the carrier. The SW voltammetric method was applied to the determination of OTC in spiked milk and eggs samples, at 100 ng mL^?1 and 200 ng g^?1 levels, respectively. The procedure involved the extraction of the analyte in ethyl acetate, evaporation of the solvent and reconstitution of the residue in acetonitrile ?5.0×10^?4 mol L^?1 tetrabutylammonium perchlorate medium. Recoveries of 96±8 and 91±8% were obtained for milk and eggs, respectively, by applying the standard additions method.     

Voltammetric Determination of 3‐Nitrofluoranthene and 3‐Aminofluoranthene at Boron Doped Diamond Thin‐Film Electrode

The voltammetric behavior of 3‐nitrofluoranthene and 3‐aminofluoranthene was investigated in mixed methanol‐water solutions by differential pulse voltammetry (DPV) at boron doped diamond thin‐film electrode (BDDE). Optimum conditions have been found for determination of 3‐nitrofluoranthene in the concentration range of 2×10^?8–1×10^?6 mol L^?1, and for determination 3‐aminofluorathnene in the concentration range of 2×10^?7–1×10^?5 mol L^?1, respectively. Limits of determination were 3×10^?8 mol L^?1 (3‐nitrofluoranthene) and 2×10^?7 mol L^?1 (3‐aminofluoranthene).     

The New Application of Boron Doped Diamond Electrode Modified with Nafion and Lead Films for Simultaneous Voltammetric Determination of Dopamine and Paracetamol

A new voltammetric procedure for the simultaneous determination of dopamine (DA) and paracetamol (PA) using boron doped diamond electrode modified with Nafion and lead films (PbF/Nafion/BDDE) was investigated. The use of this electrode resolved the overlapped voltammetric waves of DA and PA into well‐defined peaks with peak to peak separation of about 320 mV. Under the optimized experimental conditions in differential pulse voltammetric technique, DA and PA gave a linear response over the ranges 2.0×10^?7–1.0×10^?4 mol L^?1*(R²=0.9996) and 5.0×10^?7–1.0×10^?3 mol L^?1 (R²=0.9979), respectively. The detection limits were found to be 5.4×10^?8 mol L^?1 for DA and 1.4×10^?7 mol L^?1 for PA. They are lower, comparable or in some cases a little bit higher than those obtained using other electrochemical sensors. However, the proposed procedure of the sensor preparation is much simpler than procedures described in the literature with a lower detection limit. The proposed procedure was successfully applied to the determination of PA in some commercial pharmaceuticals as well as to the simultaneous determination of DA and PA in human urine, whole blood and serum samples directly without any separation steps.