Summary: Fluorescent images that illustrate acid‐catalyzed tert‐butoxycarbonyl (tBoc) deprotection patterns in polymer films were obtained using fluorescent sensors based on 7‐hydroxycoumarin dyes. Three commercial 7‐hydroxycoumarins, which are highly fluorescent, become practically nonemissive upon protection of the 7‐hydroxyl position with tBoc. In thin polymer films, the protected “prefluorescent” probes can return to their deprotected, fluorescent states by reaction with catalytic amounts of photogenerated acid and mild heating.
Protected probes become highly fluorescent after acid‐induced deprotection. 相似文献
In this work, the formation of two‐compartment micelles from symmetric pentablock copolymers in selective solvents was studied using the dissipative particle dynamics simulation technique, and the effects of block lengths and solvent quality were investigated. The simulations revealed several new morphologies and their formation mechanisms were elucidated at the molecular level, providing useful information that may contribute to the future rational design and synthesis of novel multicompartment micelles with tailored structures.
The nucleophilic living ring‐opening polymerization of N‐substituted glycine N‐carboxyanhydrides using solid‐phase synthesis resins is reported. By variation of experimental parameters, products with near Poisson distributions are obtained. As opposed to reversible deactivation radical polymerization, the living polymerization is demonstrated to be viable to high monomer conversion and through multiple monomer addition steps. Successful preparation of a multiblock copolypeptoid is proof for a highly living and robust character of the solid‐phase peptoid polymerization.
Summary: A superhydrophobic coating was facilely fabricated in one step by casting bisphenol A polycarbonate (PC) solution under moisture. Vapor‐induced phase separation occurred during the solidifying process and a rough surface with a micro‐nano‐binary structure (MNBS) similar to the microstructure shown on lotus leaf was formed.
Summary: Pulsed‐IR laser‐induced decomposition of poly(vinyl acetate) (PVAC) differs remarkably from its conventional pyrolysis, which results in the formation of acetic acid and non‐polar carbonaceous residue. In contrast, the products in the former case are (i) vinyl acetate (low energy channel), (ii) products of cleavage in the acetate group, and (iii) an ablatively deposited polar polymeric film containing roughly half of the acetoxy groups initially present.
Schematic of the different routes of poly(vinyl acetate) degradation. 相似文献
Plasma Enhanced Chemical Vapor Deposition (PECVD) of poly‐2‐hydroxyethyl methacrylate (pHEMA) biocompatible, biodegradable polymer films were produced alone and cross‐linked with ethylene glycol diacrylate (EGDA). Degree of cross‐linking was controlled via manipulation of the EGDA flow rate, which influenced the amount of swelling and the extent of degradation of the films in an aqueous solution over time. Noncross‐linked pHEMA films swelled 10% more than cross‐linked films after 24 h of incubation in an aqueous environment. Increasing degree of film cross‐linking decreased degradation over time. Thus, PECVD pHEMA films with variable cross‐linking properties enable tuning of gel formation and degradation properties, making these films useful in a variety of biologically significant applications.
Nonlinear optical vinyl polymers with high glass transition temperature (Tg) were prepared by the functionalization of a fluorinated acrylate‐methyl vinyl isocyanate copolymer. A modified pathway to obtain a thiophene bridged chromophore was worked out. Poled films of the polymers show a fairly high and stable nonlinear optical response, even at elevated temperatures.
The thiophene‐bridged chromophore, based on a substituted dicyanomethylene‐dihydrofuran acceptor, synthesized here. 相似文献
A novel phenylacetylene ( 1 ) having two hydroxyl groups and a chiral pinanyl group together with the other three related phenylacetylenes has been synthesized and (co)polymerized by using an achiral catalytic system. Among the four monomers, only 1 is suitable to the asymmetric‐induced polymerization ( AIP ). Chiral amplification phenomenon is only observed in the copolymerization of 1 with an achiral phenylacetylene having two hydroxyl groups ( 3 ). The tight helical cis‐cisoidal main chain formed by making intramolecular hydrogen bonds between the hydroxyl groups in the copoly( 1 / 3 ) enhances the efficiency of chiral induction and as a result chiral amplification phenomenon is observed during the copolymerization.
Hierarchical nanoporous structures are fabricated by adsorption of micelles of diblock copolymer‐templated Au‐nanoparticles onto a hydrophilic solid substrate. Gold nanoparticles are prepared using micelles (19 nm) of polystyrene‐block‐poly(4‐vinylpyridine) (PS‐b‐P4VP) as nanoreactors. Deposition of thin films of the micellar solution, modified with a non‐selective solvent (THF), on hydrophilic surfaces leads to the formation of hierarchical nanoporous morphologies. The thin films exhibit two different pore diameters and a total pore density of 15 × 108 holes per cm2. The structure was analyzed in terms of topography and chemical composition using AFM, TEM and XPS measurements. The PS‐b‐P4VP template was subsequently removed by oxygen plasma etching, to leave behind metallic nanopores that mimic the original thin film morphology.
This work reports a facile method to fabricate multi‐tiered polymer nanopatterns on SU‐8 by the combination of imprint‐ and photo‐lithography. First, SU‐8 is imprint patterned using a polymeric flexible mold with an anti‐adhesion coating that is deposited on a transparent and flexible substrate, at room temperature under low pressure. Next, the resulting SU‐8 nanopatterns are exposed to UV light through a chromium mask by a photolithographic process. Removal of the unexposed SU‐8 leaves behind multi‐tiered structures. The use of a hemispherical poly(dimethylsiloxane) pad facilitates the evacuation of trapped air during the imprinting process. Line/space patterns of 500 nm with the smallest line width of 200 nm were homogeneously imprint‐patterned on SU‐8 on a large flexible substrate, and three‐tiered structures, ranging in thickness from 300 nm to 2 µm, were successfully formed.
It is demonstrated that an optically transparent and electrically conductive polyethylene oxide (PEO) film is fabricated by the introduction of individualized single‐walled carbon nanotubes (SWNTs). The incorporated SWNTs in the PEO film sustain their intrinsic electronic and optical properties and, in addition, the intrinsic properties of the polymer matrix are retained. The individualized SWNTs with smaller diameter provide high transmittance as well as good electrical conductivity in PEO films.
Summary: The vapor‐based synthesis and characterization of a reactive polymer, poly[(4‐formyl‐p‐xylylene)‐co‐(p‐xylylene)] ( 1 ), have been reported. The reactive polymer coating enables the immobilization of oligosaccharides via the chemoselective aldehyde‐hydrazide coupling reaction.
We report a facile method to accomplish the crosslinking reaction of PVA with SWNTs, MWNTs, and C‐60 using MW irradiation. Nanocomposites of PVA crosslinked with SWNT, MWNT and C‐60 were prepared expeditiously by reacting the respective carbon nanotubes with 3 wt.‐% PVA under MW irradiation, maintaining a temperature of 100 °C, representing a radical improvement over literature methods to prepare such crosslinked PVA composites. This general preparative procedure is versatile and provides a simple route to manufacture useful SWNT, MWNT and C‐60 nanocomposites.
Summary: A chitin‐xylan hybrid polysaccharide having β(1 → 4)‐linked alternating structure of N‐acetyl‐D ‐glucosamine and D ‐xylose was synthesized via chitinase‐catalyzed polymerization. An oxazoline derivative of D ‐xylosyl‐β(1 → 4)‐N‐acetyl‐D ‐glucosamine ( 1 ) was effectively polymerized by the catalysis of chitinase from Bacillus sp., giving rise to a water‐soluble chitin‐xylan hybrid polysaccharide ( 2 ) in good yields. Molecular weights ( ) of 2 reached 1 500, which corresponds to 8–10 saccharide units.
A chitin‐xylan hybrid polysaccharide ( 2 ) synthesized via chitinase‐catalyzed polymerization. 相似文献
The classical Doi‐Edwards model describes the dynamics of polymer strands between entanglements and predicts stress in linear polymers. This contribution considers the dynamics of whole molecules within the same tube picture. The probability distribution function of the end‐to‐end molecule vectors after deformation and retraction was calculated. The second moment of the distribution function coincides with that derived earlier by Doi and Edwards. The damping function shows considerably weaker thinning if the molecule end‐to‐end vector is considered as a Hookean spring. The present model describes one of the possible mechanisms leading to weaker damping exhibiting, e.g., by branched polymers.
Deposition of hole injection layers including a perfluorinated ionomer has been demonstrated using layer‐by‐layer spin self‐assembly for enhanced device efficiency and lifetime in PLEDs. We show that the LBL spin self‐assembled thin films enable to control work functions of indium‐tin oxide anodes by changing the PFI concentration and that a resulting green‐emitting device has an enhanced luminescence efficiency and 18 times longer half lifetime than a device using a conventional HIL. We also fabricate a gradient of energy levels by the LBL self‐assembly of the PFI that results in a work function of 5.74 eV, which can be used to improve carrier injection even for an emitting layer whose ionization potential is over 5.7 eV.
