Adsorption of cationic starch on cellulose studied by QCM-D

The adsorption of cationic starch (CS) from aqueous electrolyte solutions onto model cellulose film has been investigated by the quartz crystal microbalance with dissipation monitoring (QCM-D) and X-ray photoelectron spectroscopy (XPS). The influence of the electrolyte composition and charge density of CS was examined. The adsorption of CS onto cellulose followed the general trends expected for polyelectrolyte adsorption on oppositely charged surfaces, with some exceptions. Thus, as result of the very low surface charge density of the cellulose surface, highly charged CS did not adsorb in a flat conformation even at low ionic strength. The porosity of the film, however, enabled the penetration of coiled CS molecules into the film at high electrolyte concentrations. Differences between the adsorption behavior of CS on cellulose and earlier observations of the adsorption of the same starches on silica could be explained by the different morphologies and acidities of the hydroxyl groups on the two surfaces.     

Adsorption of polyelectrolyte multilayers and complexes on silica and cellulose surfaces studied by QCM-D

The adsorption of polyelectrolyte (PE) multilayers and complexes, obtained from both high- and low-charge polyelectrolytes, was studied on silica and on cellulose model surfaces by quartz crystal microbalance with dissipation (QCM-D). The film properties acquired with the different strategies were compared. When polyelectrolytes were added on an oppositely charged surface in sequence to form multilayers both the change in frequency and dissipation increased. The changes in frequency and dissipation were clearly higher if low-charge PEs were used in the multilayer formation. The substrate, silica or cellulose, did not affect the adsorption behaviour of low-charge PEs and only minor differences were seen in the adsorbed amounts and changes in dissipation of high-charge PEs between SiO₂ and cellulose. The complexes formed by low-charge PEs had higher changes in frequency and dissipation at low ionic strength on both surfaces, while the complexes formed from high-charge polyelectrolytes adsorbed more at high salt concentration. The complexes of low-charge polyelectrolytes adsorbed more on silica, while the complexes formed by high-charge PEs formed thicker layers on cellulose. The charge ratio had a significant effect on the adsorption and the highest changes in frequency and dissipation were obtained in the anionic/cationic charge ratio of 0.5–0.6. Generally, the multilayers and complexes formed by low-charge polyacrylamides adsorbed highly and formed rather thick layers on both surfaces, unlike the high-charge PEs which formed thin layers using either one of the addition techniques.     

Viscoelastic properties of cationic starch adsorbed on quartz studied by QCM-D

The adsorption and viscoelastic properties of layers of a cationic polyelectrolyte (cationic starch, CS, with 2-hydroxy-3-trimethylammoniumchloride as the substituent) adsorbed from aqueous solutions (pH 7.5, added NaCl 0, 1, 100, and 500 mM) on silica were studied with a quartz crystal microbalance with dissipation (QCM-D). Three different starches were investigated (weight-average molecular weights M(w) approximately 8.7 x 10(5) and 4.5 x 10(5) with degree of substitution DS = 0.75 and M(w) approximately 8.8 x 10(5) with DS = 0.2). At low ionic strength, the adsorbed layers are thin and rigid and the amount adsorbed can be calculated using the Sauerbrey equation. When the ionic strength is increased, significant changes take place in the amount of adsorbed CS and the viscoelasticity of the adsorbed layer. These changes were analyzed assuming that the layer can be described as a Voigt element on a rigid surface in contact with purely viscous solvent. It was found that CS with low charge density forms a thicker and more mobile layer with higher viscosity and elasticity than CS with high charge density. The polymers adsorbed on the silica even when the ionic strength was so high that electrostatic interactions were effectively screened. At this high ionic strength, it was possible to study the effect of molecular weight and molecular weight distribution of the CS on the properties of the adsorbed film. Increasing the molecular weight of CS resulted in a larger hydrodynamic thickness. CS with a narrow molecular weight distribution formed a more compact and rigid layer than broadly distributed CS, presumably due to the better packing of the molecules.     

Adsorption of complexes formed by cationic starch and anionic surfactants on quartz studied by QCM-D

The adsorption of complexes of cationic starch, (CS) and a series of homologous sodium alkanoates on silica was studied with the quartz crystal microbalance with dissipation (QCM-D) instrument. The systems were chosen so as to represent CS/surfactant ratios below and above the critical association concentrations of the surfactants but below their critical micelle concentrations. It was found that

– surfactants did not adsorb on cationic polymers that were very tightly bound to the surface;

– surfactants did adsorb on polyelectrolytes forming layers with loops and tails extending into the solution, provided the concentration of surfactant was at least around the critical association concentration (cac) of the surfactant/polymer system;

– adsorption of surfactant was promoted by increasing the surfactant chain length and by adding simple electrolyte that weakened the electrostatic polymer/surface interaction and

– multilayers were formed when the surfactant concentration in solution was well above the cac; their formation was promoted by increasing hydrophobic interactions, e.g. by increasing the surfactant chain length.

Adsorption properties of polyelectrolyte-surfactant complexes on hydrophobic surfaces studied by QCM-D

Adsorption and deposition from turbid solutions are common in many industrial processes but notoriously difficult to investigate using standard optical techniques such as ellipsometry and reflectometry. In this report, we have addressed this problem by employing a quartz crystal microbalance with dissipation monitoring ability, QCM-D. The system under investigation consisted of a cationic polyelectrolyte, poly(vinylamine), PVAm, and an anionic surfactant, sodium dodecyl sulfate, SDS, which were mixed together in 10 mM NaCl solution. The polyelectrolyte and the surfactant readily associate in bulk solution, resulting in increased solution turbidity once large aggregates are formed. The solutions were placed in contact with a polystyrene surface, and the adsorption process was monitored by following the changes in the resonance frequency and dissipation factor. The results obtained can in most cases be evaluated using the Sauerbrey relation, but in some cases a more elaborate analysis is necessary. It is found that PVAm adsorbs to polystyrene in the absence of SDS. In the turbid region, deposition is observed, and the sensed mass exceeds the sum of that obtained for each of the components alone. On the other hand, at high SDS concentrations, the surfactant dominates in the adsorbed layer. Adsorption equilibrium is in most cases established within 1-2 h, the exception being found around the solution composition that results in the formation of charge-neutralized aggregates. In this case, a slow deposition of aggregates persists over prolonged times.     

Adsorption of bacteria and polycations on model surfaces of cellulose, hemicellulose and wood extractives studied by QCM-D

Quartz crystal microbalance with dissipation monitoring (QCM-D), atomic force microscopy (AFM) and field emission scanning electron microscopy (FESEM) were used as the tools to study the adsorption of bacteria onto surfaces of silica and polystyrene coated with materials related to papermaking. Cationic polyelectrolytes used as fixatives and retention aids in paper industry were found to promote irreversible adsorption of the ubiquitous white water bacterium, Pseudoxanthomonas taiwanensis, onto model surfaces of cellulose (pH 8). The high charged low molecular weight polyelectrolyte, poly(diallyldimethyl) ammonium chloride (pDADMAC) adsorbed to silica surface as a flat and rigid layer, whereas the low charged cationic polyacryl amide (C-PAM) of high molecular weight adsorbed as a thick and loose layer. AFM images showed that the polyelectrolytes accumulated as layers around each bacterial cell. In the presence of wood hemicellulose (O-acetyl-galactoglucomannan) the bacteria adsorbed massively, as large, tightly packed rafts (up to 0.05mm in size) onto the polystyrene crystal surface coated with wood extractives (pH 4.7). AFM and FESEM micrographs also showed large naked areas (with no bacteria) in between the bacterial rafts on the crystal surface. In this case, QCM-D only incompletely responded to the massiveness of the bacterial adsorption. The results indicate that cationic polymers can be used to increase the retention of bacteria from the process water onto the fibre web and that, depending on the balance between hemicelluloses and wood extractives and pH of the process waters, bacteria can be drawn from process waters onto surfaces.     

Improving the combination of cellulose and lignin using xylan as a compatibilizer

Cellulose - Both cellulose and lignin are rich natural resources; however, recombining them to...     

Dependence of the viscoelastic properties of cellulose on water content

The dynamic mechanical properties at about 1 Hz of a film of regenerated cellulose have been measured over a range of temperatures from ?100 to +90°C and water contents from effectively zero to 3%. Three loss peaks were found which were attributed to molecular motions in the amorphous regions. One of these was postulated to involve motion of segments of two chains connected through hydrogen bonding via a “tightly bound” molecule of water. Viscoelastic measurements over a somewhat wider range of water contents at room temperature exhibited contradictory effects depending upon the amount of water. These results provide support for the concept of two types of water in cellulose: tightly bound and loosely bound.     

Adsorption and viscoelastic properties of fractionated mucin (BSM) and bovine serum albumin (BSA) studied with quartz crystal microbalance (QCM-D)

The adsorption profile and viscoelastic properties of bovine submaxillary gland mucin (BSM) and bovine serum albumin (BSA), extracted from a commercial mucin preparation, adsorbing to polystyrene surfaces has been studied using quartz crystal microbalance with dissipation monitoring (QCM-D). A significant difference in the adsorption properties of the different proteins was detected; with the BSA adsorbing in a flat rigid layer whilst the mucin adsorbed in a diffuse, highly viscoelastic layer. Subsequent addition of BSA to the preadsorbed mucin layer resulted in stiffening of the protein layer which was attributed to complexation of the mucin by BSA. In contrast, a preadsorbed layer of BSA prevented mucin adsorption altogether. Combined mixtures of mucin and BSA in well defined ratios revealed intermediate properties between the two separate protein species which varied systematically with the protein ratios. The results shed light on the synergistic effects of complexation of lower molecular weight biomolecular species with mucin. The possibility to selectively control protein uptake and tailor the physical properties of the adsorbed layer makes mucin an attractive option for application in biomaterial coatings.     

Adsorption and desorption properties of trans-resveratrol on cellulose cotton.

The adsorption and desorption properties of trans-Resveratrol (Res) on the cellulose cotton were investigated under various conditions, such as the pH, alcohol percentage, temperature and equilibrium times. Moreover, the acidic-dissociation constants were determined to be pKa1 = 8.01, pKa2 = 9.86 and pKa3 = 10.5 by a curve-fitting method. Also, it was found that the adsorption depended on the temperature and salting effect. On the other hand, the desorptions from cellulose were examined using several kinds of water-miscible organic solvents (methanol, ethanol, acetone and THF).     

Adsorption of cationic surfactants and subsequent adsolubilization of organic compounds onto cellulose fibers

Cationic surfactants with different hydrophobic chain length were adsorbed onto cellulose fibers in an aqueous medium. The adsorption isotherms exhibited three characteristic regions which were interpreted in terms of the mode of aggregation of the surfactant molecules at the solid–liquid interface. The hydrophobic layers were used as a reservoir to trap various slightly water soluble organic molecules. A quantitative study of these phenomena suggested typical partition behavior of the organic solutes between the aqueous phase and the surfactant layer. The surfactant chain length (from C12 to C18) was shown to play an important role in terms of the capacity to retain the organic solute and the capacity increased with the number of carbon atoms.     

生物质三组分热裂解行为的对比研究

在热天平上对比研究了生物质中的纤维素、半纤维素和木质素三种主要组分的热失重规律。结果表明,作为半纤维素模型化合物的木聚糖热稳定性差,在217℃～390℃发生明显分解;纤维素热裂解起始温度最高,且主要失重发生在较窄温度区域,固体残留物仅为6.5%;木质素表现出较宽的失重温度区域,最终固体残留物高达42%。在红外辐射机理试验台上对比研究了三组分热裂解产物随温度的变化规律。三组分热裂解生物油产量随温度变化先升后降。纤维素生物油产量在峰值上最高,但纤维素生物油热稳定性差,高温时挥发分的二次分解最明显;木聚糖和木质素生物油产量较低,表现出较好的热稳定性。三组分热裂解焦炭产量随温度升高而降低,最终纤维素热裂解焦炭产量为1.5%,而木聚糖和木质素分别为22%和26%。三组分热裂解气体产物随温度升高而增长,但在气体组成分布上因三组分的结构上的差异而不同。     

Enzymatic kinetics of cellulose hydrolysis: a QCM-D study

The interactions between films of cellulose and cellulase enzymes were monitored using a quartz crystal microbalance (QCM). Real-time measurements of the coupled contributions of enzyme binding and hydrolytic reactions were fitted to a kinetic model that described closely significant cellulase activities. The proposed model combines simple Boltzmann sigmoidal and 1 - exp expressions. The obtained kinetics parameters were proven to be useful to discriminate the effects of incubation variables and also to perform enzyme screening. Furthermore, it is proposed that the energy dissipation of a film subject to enzymatic hydrolysis brings to light its structural changes. Overall, it is demonstrated that the variations registered in QCM frequency and dissipation of the film are indicative of mass and morphological transformations due to enzyme activities; these include binding phenomena, progressive degradation of the cellulose film, existence of residual, recalcitrant cellulose fragments, and the occurrence of other less apparent changes throughout the course of incubation.     

Adsorption of cationic gemini surfactants at solid surfaces studied by QCM-D and SPR: effect of the rigidity of the spacer

Two small series of cationic gemini surfactants with dodecyl tails have been synthesized and evaluated with respect to self-assembly in bulk water and at different solid surfaces. The first series contained a flexible alkane spacer and is denoted 12-n-12, with n = 2, 4, and 6. The second series had a phenylene group connected to the quaternary nitrogens in either the meta or para position and the surfactants are referred to as 12-m-Φ-12 and 12-p-Φ-12, respectively. The phenylene group is a rigid linker unit. The critical micelle concentration (cmc) was determined both by tensiometry and by conductometry, and the packing density of the surfactants at the air-water interface was calculated from the Gibbs equation. The cmc values for the geminis with a rigid spacer, 12-m-Φ-12 and 12-p-Φ-12, were of the same order of magnitude as for 12-4-12, which is the flexible surfactant that most closely matches the phenylene-based surfactants with respect to hydrophobicity, measured as log P, and distance between the positively charged nitrogen atoms. The adsorption of flexible and rigid surfactants was investigated on gold, silicon dioxide (silica), gold made hydrophobic by the self-assembly of hexadecanethiol, and gold made hydrophilic by the self-assembly of 16-hydroxyhexadecanethiol. On all of the surfaces, there was a reverse relationship between the adsorbed amount at the cmc and the length of the spacer (i.e., 12-2-12 gave the highest and 12-6-12 gave the lowest amount of adsorbed material). The adsorption pattern was similar for all of the surfactants when recorded at 25 °C. Thus, one can conclude that a rigid spacer does not render the self-assembly of a gemini surfactant difficult, neither in bulk water nor at solid surfaces. However, on one of the surfaces-untreated gold-the adsorbed amount of the geminis with a rigid spacer at 40 °C was approximately twice the values obtained at 25 °C. This is interpreted as the formation of an interdigitated bilayer at 25 °C and a regular bilayer without interpenetration of the alkyl chains at 40 °C.     

Quantification of a tightly adsorbed monolayer of xylan on cellulose surface

The successive extraction and re-adsorption of a linear β-(1 → 4) xylan extracted from microfibrillated birch pulp was investigated using solid-state CP/MAS ¹³C NMR spectroscopy, specific surface area measurements, and atomistic molecular dynamics (MD) simulations. The NMR spectra confirmed that when in contact with cellulose after re-adsorption, the xylan molecules altered their conformation from the classical left-handed threefold structure found in the bulk to a different one, presumably a cellulose-like twofold system for quantities up to the equivalent amount of extracted xylan. Combining these observations with specific surface area measurements and the surface occupied by a xylosyl residue, it was possible to show that the re-adsorbed xylan in the modified conformation occurred only within the first adsorbed layer in direct interaction with the cellulose surface. It is only when an excess xylan was added and after full cellulose surface coverage, that the subsequent deposited layers took the classical threefold organization. Following the variation of xylan conformation in terms of sequential xylan addition allowed quantifying the surface of cellulose accessible for a tight adsorption of xylan, not only for microfibrillated birch cellulose, but for other samples as well. The MD simulations confirmed that xylan in threefold conformation had a weaker affinity for the cellulose surface than its twofold counterpart, thus supporting the hypothesis of the twofold conformation for xylan at the cellulose surface. The MD simulations also showed that in contact with cellulose, the adsorbed xylan was mainly organized as an extended molecular chain aligned parallel to the cellulose chain direction.     

Composite film coatings based on epoxy-polysiloxane systems of cationic polymerization and their anticorrosion properties

The anticorrosion properties of epoxy-polysiloxane coatings on the surface of the aluminum alloy D-16 were studied by a potentiodynamic method. It was established that the use of the hybrid coating led to an increased corrosion resistance from 0.250 kΩm·cm² for uncoated alloy to 0.396-0.996 kΩm·cm² for the coated aluminum support. The yield of the sol fraction, the micro hardness, and the glass transition temperature of the polymers were determined.