Quasi‐Block Copolymers Based on a General Polymeric Chain Stopper

Quasi‐block copolymers (q‐BCPs) are block copolymers consisting of conventional and supramolecular blocks, in which the conventional block is end‐terminated by a functionality that interacts with the supramolecular monomer (a “chain stopper” functionality). A new design of q‐BCPs based on a general polymeric chain stopper, which consists of polystyrene end‐terminated with a sulfonate group (PS‐SO₃Li), is described. Through viscosity measurements and a detailed diffusion‐ordered NMR spectroscopy study, it is shown that PS‐SO₃Li can effectively cap two types of model supramolecular monomers to form q‐BCPs in solution. Furthermore, differential scanning calorimetry data and structural characterization of thin films by scanning force microscopy suggests the existence of the q‐BCP architecture in the melt. The new design considerably simplifies the synthesis of polymeric chain stoppers; thus promoting the utilization of q‐BCPs as smart, nanostructured materials.     

Chiral Supramolecular Multiblock Copolymerization Accompanying Chirality Transfer in Heterostructures via Living Chain Growth

We report the unique synthesis of chiral supramolecular tri- and penta-BCPs with controllable chirality using kinetically adjusted seeded supramolecular copolymerization in THF and DMSO (99 : 1, v/v). Tetraphenylethylene (d - and l -TPE) derivatives bearing d - and l -alanine side chains formed thermodynamically favored chiral products via a kinetically trapped in monomeric state with a long lag phase. In contrast, achiral TPE-G containing glycine moieties did not form a supramolecular polymer owing to the energy barrier in its kinetically trapped state. We show that the copolymerization of the metastable states of TPE-G not only enables the generation of supramolecular BCPs by the seeded living growth method, but also transfers chirality at the seed ends. This research demonstrates the generation of chiral supramolecular tri- and penta-BCPs with B-A-B, A-B-A-B-A, and C-B-A-B-C block patterns accompanying chirality transfer via seeded living polymerization.     

Poly(ε‐caprolactone)–poly(isobutylene): A crystallizing,hydrogen‐bonded pseudo‐block copolymer

The crystallization of block copolymers (BCPs) under homogeneous and heterogeneous nucleation is currently well understood revealing the strong interplay of crystallization in competition to microphase separation. This article reports investigations on synthesis and crystallization processes in weakly interacting supramolecular pseudo‐BCPs, composed of poly(ε‐caprolactone) (PCL) and poly(isobutylene) (PIB) blocks, connected by a specifically interacting hydrogen bond (thymine/2,6‐diaminotriazine). Starting from ring opening polymerization of ε‐caprolactone, the use of “click”‐chemistry enabled the introduction of thymine endgroups onto PCL polymer, thus generating the fully thymine‐substituted pure PCLs ( 1a , 1b ) as judged via NMR and MALDI analysis. Physical mixing of 1a , 1b with a bivalent, bis(2,6‐diaminotriazine)‐containing molecule ( 2 ) generated the bivalent polymers BC1 and BC2 , whereas mixing of 1a or 1b with the 2,6‐diaminotriazine‐substituted PIB ( 3 ) generated the supramolecular pseudo‐BCPs BC3 and BC4 . Thermal investigations (DSC, Avrami analysis) revealed only minor changes in the crystallization behavior of BC1 – BC4 with Avrami exponents close to three, indicative of a confluence of the growing crystals during the crystallization process. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Highly Ordered Nanoporous Films from Supramolecular Diblock Copolymers with Hydrogen‐Bonding Junctions

We designed efficient precursors that combine complementary associative groups with exceptional binding affinities and thiocarbonylthio moieties enabling precise RAFT polymerization. Well defined PS and PMMA supramolecular polymers with molecular weights up to 30 kg mol^?1 are synthesized and shown to form highly stable supramolecular diblock copolymers (BCPs) when mixed, in non‐polar solvents or in the bulk. Hierarchical self‐assembly of such supramolecular BCPs by thermal annealing affords morphologies with excellent lateral order, comparable to features expected from covalent diblock copolymer analogues. Simple washing of the resulting materials with protic solvents disrupts the supramolecular association and selectively dissolves one polymer, affording a straightforward process for preparing well‐ordered nanoporous materials without resorting to crosslinking or invasive chemical degradations.     

In situ Nucleation-Growth Strategy for Controllable Heterogeneous Supramolecular Polymerization of Liquid Crystalline Block Copolymers and Their Hierarchical Assembly

The self-assembly morphologies of subunits are largely governed by thermodynamics, which plays a less important role in dimensional control. Particularly for one-dimensional assemblies from block copolymers (BCPs), the negligible energy difference between short and long ones imposes great challenges in length control. Herein, we report that by incorporating additional polymers to induce in situ nucleation and trigger the subsequent growth, controllable supramolecular polymerization driven by mesogenic ordering effect could be realized from liquid crystalline BCPs. The length of the resultant fibrillar supramolecular polymers (SP) is controlled by tuning the ratio between nucleating and growing components. Depending on the choice of BCPs, the SPs can be homopolymer-like, heterogeneous triblock, and even pentablock copolymer-like. More interestingly, with insoluble BCP as a nucleating component, amphiphilic SPs are fabricated, which can undergo spontaneous hierarchical assembly.     

Fabrication of Supramolecular Semiconductor Block Copolymers by Ring‐Opening Metathesis Polymerization

ω‐Telechelic poly(p‐phenylene vinylene) species (PPVs) are prepared by living ring‐opening metathesis polymerization of a [2.2]paracyclophane‐1,9‐diene in the presence of Hoveyda–Grubbs 2nd generation initiator, with terminating agents based on N¹,N³‐bis(6‐butyramidopyridin‐2‐yl)‐5‐hydroxyisophthalamide (Hamilton wedge), cyanuric acid, Pd^II–SCS‐pincer, or pyridine moieties installing the supramolecular motifs. The resultant telechelic polymers are self‐assembled into supramolecular block copolymers (BCPs) via metal coordination or hydrogen bonding and analyzed by ¹H NMR spectroscopy. The optical properties are examined, whereby individual PPVs exhibit similar properties regardless of the nature of the end group. Upon self‐assembly, different behaviors emerge: the hydrogen‐bonding BCP behaves similarly to the parent PPVs whereas the metallosupramolecular BCP demonstrates a hypsochromic shift and a more intense emission owing to the suppression of aggregation. These results demonstrate that directional self‐assembly can be a facile method to construct BCPs with semiconducting networks, while combating solubility and aggregation.     

Dually responsive multiblock copolymers via RAFT polymerization: Synthesis of temperature- and redox-responsive copolymers of PNIPAM and PDMAEMA

We report synthesis of temperature- and redox-responsive multiblock copolymers by reversible addition-fragmentation chain transfer (RAFT) polymerization. Well-defined α,ω-bis(dithioester)-functionalized poly(N-isopropylacrylamide) (PNIPAM) and poly(2-(dimethylamino) ethyl methacrylate) (PDMAEMA) were prepared using 1,4-bis(thiobenzoylthiomethyl)benzene and 1,4-bis(2-(thiobenzoylthio)prop-2-yl)benzene as RAFT agents, respectively. Dually responsive multiblock copolymers were synthesized in a single aminolysis/oxidation step from the α,ω-bis(dithioester)-terminated PNIPAM and PDMAEMA. The copolymers and their stimulus-responsive behavior were characterized by size exclusion chromatography, NMR, light scattering and atomic force microscopy. Due to the presence of redox-sensitive disulfide bonds between the blocks, the copolymers were readily reduced to the starting polymer blocks. The presence of temperature-responsive PNIPAM blocks provided the copolymers with the ability to assemble into core-shell nanostructures with hydrophobic PNIPAM as a core and cationic PDMAEMA as stabilizing shell when above the phase transition temperatures of PNIPAM. The temperature-induced assembly of the copolymers also showed substantial pH sensitivity. The phase transition temperature increased with decreasing pH, while molecular weight of the assemblies decreased.     

The Origin of Hierarchical Structure Formation in Highly Grafted Symmetric Supramolecular Double‐Comb Diblock Copolymers

Involving supramolecular chemistry in self‐assembling block copolymer systems enables design of complex macromolecular architectures that, in turn, could lead to complex phase behavior. It is an elegant route, as complicated and sensitive synthesis techniques can be avoided. Highly grafted double‐comb diblock copolymers based on symmetric double hydrogen bond accepting poly(4‐vinylpyridine)‐block‐poly(N‐acryloylpiperidine) diblock copolymers and donating 3‐nonadecylphenol amphiphiles are realized and studied systematically by changing the molecular weight of the copolymer. Double perpendicular lamellae‐in‐lamellae are formed in all complexes, independent of the copolymer molecular weight. Temperature‐resolved measurements demonstrate that the supramolecular nature and ability to crystallize are responsible for the formation of such multiblock‐like structures. Because of these driving forces and severe plasticization of the complexes in the liquid crystalline state, this supramolecular approach can be useful for steering self‐assembly of both low‐ and high‐molecular‐weight block copolymer systems.     

Trackable Supramolecular Fusion: Cage to Cage Transformation of Tetraphenylethylene-Based Metalloassemblies

Herein, the trackable supramolecular transformation of a two-component molecular cage to a three-component cage through supramolecular fusion with another two-component molecular square is described. The use of tetraphenylethene (TPE), a chromophore with aggregation-induced emission (AIE) character, as a component for the molecular cages enables facile fluorescence monitoring of the transformation process: while both cages exhibit fluorescence emission via the restriction of intramolecular motion of the TPE motif, the interactions between TPE and 4,4′-bipyridine introduced in the supramolecular fusion process result in partial fluorescence quenching and shifts in the emission maximum. This study provides a simple and efficient approach towards complex supramolecular cages with emergent functions and demonstrates that AIE features could provide unique opportunities for the characterization of complex, dynamic supramolecular transformation processes.     

Costereosymmetric α-olefin copolymers

Copolymerization of propylene and 1-butene with highly stereospecific three-component coordination catalysts produced multiblock crystalline copolymers having stereo-regular sequences of both propylene and 1-butene. Copolymers containing from 3 to about 80% 1-butene had two DTA melting points which were attributable to polypropylene and poly-1-butene crystallinity. Those containing from 18 to about 70% 1-butene had x-ray diffraction patterns showing peaks characteristic of polypropylene and form I poly-1-butene, but form II poly-1-butene crystallinity was never observed. The multiblock copolymer structure observed is also supported by the fact that the product of the reactivity ratios is greater than unity. The composition distributions of low-conversion and continuously prepared copolymers were similar and relatively broad. For example, copolymers containing an average of 12% 1-butene had species containing from 5–30% 1-butene. High-conversion copolymers had an even broader composition distribution due to the gradual increase of the 1-butene concentration in the comonomer mixture as the copolymerization proceeded. The absence of homopolymers was demonstrated by fractionation. The ability to detect homopolymers was proved by the fact that a mixture of stereoregular polypropylene and poly-1-butene were readily separated. Increasing the amount of 1-butene tended to decrease those properties dependent upon crystallinity such as hardness, tensile strength, stiffness, density, and melting point, but tended to improve significantly the impact strength, low temperature properties, and clarity of molded objects. These duocrystalline copolymers retained a much higher level of properties than that observed for random copolymers prepared with less stereospecific coordination catalysts.     

Synthesis and properties of multiblock copolymers based on polydimethylsiloxane and polyamides from dicarboxylic acid and diisocyanate terminated functionalities

Polydimethylsiloxane (PDMS)–polyamide multiblock copolymers were successfully synthesized via diisocyanate route by two different procedures, i.e., the one-step and two-step methods, In the two-step method, α, ω-diisocyanate-terminated polyamide oligomers, which were prepared in situ from a mixture of isophthalic acid (IPA) and azelaic acid (AZA) with 4,4′-methylenedi (phenyl isocyanate) (MDI) in 1,3-dimethyl-2-imidazolidone (DMI) in the presence of 3-methyl-1-phenyl-2-phosopholene 1-oxide catalyst, were reacted with α, ω-bis (10-carboxydecyl) polydimethylsiloxane (PDMS-diacid) leading to the formation of multiblock copolymers. In the one-step method, the reaction components, MDI, IPA, AZA, and PDMS-diacid were reacted all together in DMI in the presence of the catalyst. These polymerizations gave multiblock copolymers having inherent viscosities in the range of 0.36–1.12 dL/g in N,N-dimethylacetamide (DMAc). These multiblock copolymers were soluble in amide-type solvents, and transparent (or translucent) and ductile films could be cast from the solutions in a mixture of DMAc and bis(2-ethoxyethyl) ether. The multiblock copolymers prepared by the two-step method had better-defined, microphase-separated morphology than those obtained by the one-step method. The mechanical properties of PDMS–polyamide multiblock copolymer films were found to be highly dependent on the PDMS content; the tensile strength and modulus of the films decreased with increasing the PDMS content.     

刺激响应性刚柔嵌段共聚物的自组装

刚柔嵌段共聚物是指刚性链段和柔性链段以共价键相连形成的共聚物。不仅由于刚性链段有序排列的特点使得其自组装行为更为丰富多样,而且刚性分子将优异的功能特性赋予到超分子组装体中,有望实现超分子材料的功能应用。这类嵌段共聚物在溶液中自组装形成的聚集体会对外界的刺激(例如pH、光、温度、化学添加剂等)敏感,产生聚集体形态的变化。本文选取了部分典型的具有刺激响应性的刚柔嵌段共聚物,介绍了其智能自组装行为,并对其良好的发展前景做了展望。     

A-B-A Triblock and (A-B)n Segmented Block Copolymers of Styrene and Ethylene Oxide via Thermal Iniferters

A free radical technique is described for the synthesis of tri- and multiblock copolymers of styrene and ethylene oxide through polyethylene oxide-based thermal “iniferters.” The mono- or dihydroxy-terminated oligomeric polyethylene oxides were chemically transformed to the secondary amine terminated species. Thiocarba-mylation and oxidation of the amine groups gave rise to macro- or polymeric thiuram disulfides called macro- or polymeric “iniferters,” respectively. Thermal polymerization of styrene in the presence of the macro iniferter led to the formation of their perfect triblock copolymers, with styrene forming the central block. Utilization of the polymeric iniferter, on the other hand, give rise to (A-B)_n type segmented copolymers containing as many as 3 (A-B) sequences. The length of each block could be regulated by the choice of the appropriate iniferter and its relative concentration with respect to the monomer. The iniferters and the block copolymers were characterized.     

Self-assembly and Properties of Block Copolymers Containing Mesogen-Jacketed Liquid Crystalline Polymers as Rod Blocks

Mesogen-jacketed liquid crystalline polymer (MJLCP) has attracted great attention because of its rigid conformation, facile synthesis, and structural controllability. In this feature article, the self-assembly of MJLCP-based block copolymers (BCPs) is briefly reviewed, especially the nanostructures of rod-coil diblock copolymers (diBCPs), rod-rod diBCPs, and triblock copolymers. In addition, the properties of the self-assembled BCPs are also summarized, including their applications as liquid crystalline thermoplastic elastomers and solid polymer electrolytes. The article also discusses the major challenges and future directions in the study of MJLCP-based BCPs.     

Synthesis and properties of sulfonated multiblock copoly(ether sulfone)s by a chain extender

A new series of sulfonated multiblock copoly(ether sulfone)s applicable to proton exchange membrane fuel cells was synthesized. The multiblock copolymers were synthesized by the nucleophilic aromatic substitution of hydroxyl‐terminated oligomers in the presence of highly reactive decafluorobiphenyl (DFB) as a chain extender. Because of the high reactivity of DFB, the ether–ether interchange reaction, which could lead to a randomized polymer architecture, was prevented, and multiblock copolymers with high molecular weights were easily produced. The multiblock copolymers gave tough, flexible, and transparent membranes by solution casting. The ion exchange capacity values could be easily controlled by changing the sulfonated block ratios in the copolymers. The resulting membranes demonstrated good oxidative and dimensional stability and significantly higher proton conductivity than sulfonated random poly(ether sulfone) copolymers. The morphologies of the membranes were investigated by tapping mode atomic force microscopy, which showed that the multiblock membranes had a clear hydrophilic/hydrophobic separated structure. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3947–3957, 2008     

Synthesis and characterization of multiblock copolymers based on hydrophilic disulfonated poly(arylene ether sulfone) and hydrophobic partially fluorinated poly(arylene ether ketone) for fuel cell applications

Sulfonated fluorinated multiblock copolymers based on high performance polymers were synthesized and evaluated for use as proton exchange membranes (PEMs). The multiblock copolymers consist of fully disulfonated poly(arylene ether sulfone) and partially fluorinated poly(arylene ether ketone) as hydrophilic and hydrophobic segments, respectively. Synthesis of the multiblock copolymers was achieved by a condensation coupling reaction between controlled molecular weight hydrophilic and hydrophobic oligomers. The coupling reaction could be conducted at relatively low temperatures (e.g., 105 °C) by utilizing highly reactive hexafluorobenzene (HFB) as a linkage group. The low coupling reaction temperature could prevent a possible trans‐etherification, which can randomize the hydrophilic‐hydrophobic sequences. Tough ductile membranes were prepared by solution casting and their membrane properties were evaluated. With similar ion exchange capacities (IECs), proton conductivity and water uptake were strongly influenced by the hydrophilic and hydrophobic block sequence lengths. Conductivity and water uptake increased with increasing block length by developing nanophase separated morphologies. Atomic force microscopy (AFM) and transmission electron microscopy (TEM) experiments revealed that the connectivity of the hydrophilic segments was enhanced by increasing the block length. The systematic synthesis and characterization of the copolymers are reported. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 214–222, 2010     

Performance assessment of hybrid multiblock copolymers included with ionic liquid for fuel cell applications

To improve the proton conductivity and thermal stability of proton exchange membrane, hybrid poly (arylene ether) multiblock copolymers were synthesized by using 6F-bisphenol A monomer. The hydrophobic oligomers poly (arylene ether sulfone) containing 6F-bisphenol A with varying molecular weight were copolymerised with hydrophilic oligomer disulfonated poly (arylene ether ketone) containing pendant carboxylic acid group to prepare multiblock copolymers. For further enhancing the proton conductivity, ionic liquid is embedded into the synthesized multiblock copolymers to fabricate the hybrid multiblock membranes. The ¹H NMR studies confirmed the synthesis of oligomers and multiblock copolymers whereas the FT-IR spectra revealed the interaction of ionic liquid with the multiblock copolymers. The proton conductivity of the membranes has also been examined at different temperatures and the activation energy required for the proton transport was calculated by using Arrhenius equation. At 30 °C, the maximum proton conductivity of 0.14 S/cm were shown by hybrid membrane (with 50% ionic liquid, 6FB1/I.L-50%), which is of 3.5 times greater than that of pristine 6FB1 membrane. Compared with pristine membranes, the hybrid membranes exhibit improved oxidative, thermal and mechanical stability. Moreover, the scanning electron microscopy (SEM) investigation depicts better phase separation in hybrid membranes than pristine membranes by forming ionic clusters. The membranes have been tested in H₂/O₂ fuel cell and their performance is compared with the state-of-art Nafion 117 membrane.     

聚丙交酯/聚乙二醇多嵌段共聚物的合成及其性能

聚丙交酯 (ＰＬＬＡ)由于具有良好的生物降解性和生物相容性 ,在医学领域已经得到了广泛的临床应用 ,近来又被制备成细胞支架大量应用于组织工程中[1,2 ] ,但由于其疏水性而造成细胞亲和性不好 .聚乙二醇 (ＰＥＧ)具有良好的亲水性 ,良好的生物相容性 ,但是ＰＥＧ是非降解性的 ,只有低分子量的ＰＥＧ可以被吞噬细胞所吞噬或透过肾滤膜而排出体外 ,因此 ,低分子量的ＰＥＧ常被用来与丙交酯 (Ｌ ＬＡ)共聚以改善ＰＬＬＡ支架的亲水性 .聚丙交酯 聚乙二醇共聚物 (ＰＬＥ)的三嵌段及两嵌段共聚物的合成及其性能的研究已被广泛报道[3～ 5] .研究…     

Segmented sulfonated poly(arylene ether sulfone)‐b‐polyimide copolymers for proton exchange membrane fuel cells. I. Copolymer synthesis and fundamental properties

Segmented disulfonated poly(arylene ether sulfone)‐b‐polyimide copolymers based on hydrophilic and hydrophobic oligomers were synthesized and evaluated for use as proton exchange membranes (PEMs). Amine terminated sulfonated poly (arylene ether sulfone) hydrophilic oligomers and anhydride terminated naphthalene based polyimide hydrophobic oligomers were synthesized via step growth polymerization including high temperature one‐pot imidization. Synthesis of the multiblock copolymers was achieved by an imidization coupling reaction of hydrophilic and hydrophobic oligomers oligomers in a m‐cresol/NMP mixed solvent system, producing high molecular weight tough and ductile membranes. Proton conductivities and water uptake increased with increasing ion exchange capacities (IECs) of the copolymers as expected. The morphologies of the multiblock copolymers were investigated by tapping mode atomic force microscopy (TM‐AFM) and their measurements revealed that the multiblock copolymers had well‐defined nano‐phase separated morphologies which were clearly a function of block lengths. Hydrolytic stability test at 80 °C water for 1000 h showed that multiblock copolymer membranes retained intrinsic viscosities of about 80% of the original values and maintained flexibility which was much improved over polyimide random copolymers. The synthesis and fundamental properties of the multiblock copolymers are reported here and the systematic fuel cell properties will be provided in a separate article. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4879–4890, 2007     

Multiblock poly(4‐vinylpyridine) and its copolymer prepared with cyclic trithiocarbonate as a reversible addition–fragmentation transfer agent

The polymerization of 4‐vinylpyridine was conducted in the presence of a cyclic trithiocarbonate (4,7‐diphenyl‐[1,3]dithiepane‐2‐thione) as a reversible addition–fragmentation transfer (RAFT) polymerization agent, and a multiblock polymer with narrow‐polydispersity blocks was prepared. Two kinds of multiblock copolymers of styrene and 4‐vinylpyridine, that is, (ABA)_n multi‐triblock copolymers with polystyrene or poly(4‐vinylpyridine) as the outer blocks, were prepared with multiblock polystyrene or poly(4‐vinylpyridine) as a macro‐RAFT agent, respectively. GPC data for the original polymers and polymers cleaved by amine demonstrated the successful synthesis of amphiphilic multiblock copolymers of styrene and 4‐vinylpyridine via two‐step polymerization. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2617–2623, 2007