高分子发光二极管载流子注入过程研究

采用交流阻抗谱，电容-电压，电容-频率等实验方法，研究了共轭高分子MEH-PPV(poly［2-methoxy，5-(2-ethylhexoxy)-1，4-phenylene vinylene］)发光二极管的载流子注入过程.对于结构为ITO/PEDOT/MEH-PPV/Ba/Al的发光器件，实验结果表明，电极界面是欧姆接触的，载流子的注入是非平衡的，器件薄膜中存在陷阱容易俘获注入电荷，形成空间电荷区，陷阱密度约为3.75×10¹⁶cm^-3. 关键词： 高分子发光二极管 交流阻抗谱 cole-cole图 载流子注入     

Enhanced quantum efficiency in polymer electroluminescence devices by inserting an ultrathin PMMA layer

We report an increase of electroluminescence (EL) efficiency by about two times for poly(2-methoxy-5-(2′-ethylhexyloxy)-1,4-phenylene vinylene) (MEH-PPV) based polymer light-emitting diodes (PLED) while employing an ultrathin layer of poly(methyl methacrylate) (PMMA) between a hole injection layer, polyethylenedioxythiophenne:polystyrenesulfonate (PEDOT:PSS) and an emitting layer, MEH-PPV. The peak power efficiency of the control device (ITO/MEH-PPV/LiF/Al) was 0.42 lm/W with a current efficiency of 0.66 cd/A. The device with the optimized thickness of PMMA interface layer shows the highest power efficiency of 1.15 lm/W at a current efficiency exceeding 1.83 cd/A. The significant improvement in the device performance is attributed to the decrease of holes injection and the promotion of electrons injection, which cause the balance of the carriers within the emitting layer.     

基于柔性基底异质结有机薄膜的光伏器件

研究了基于柔性基板的有机薄膜太阳能电池,实验以聚3,4-乙撑二氧噻吩/聚苯乙烯磺酸盐作为阳极修饰层,1,4-亚苯基亚乙烯基（MEH-PPV）材料作为给体层以及富勒烯（C60）材料作为受体层制备异质结柔性有机太阳能电池。实验结果表明:增加阳极修饰层,虽然会阻挡光的吸收,但是可以大幅度地提高短路电流、开路电压、填充因子和能量转换效率4个参数。并发现MEH-PPV受体层的厚度对有机太阳能电池的性能有较大影响,当受体层厚度为90 nm时能量转换效率达到最大,为1.29%。     

聚合物发光二极管中的负电容效应

采用交流阻抗谱技术,研究了以共轭聚合物(poly［2-methoxy,5-(2′-ethylhexoxy)-1,4-phenylenevinylene］)(MEH-PPV)为发光层,以带有胺基的聚芴共聚物poly［(9,9-bis(3′-(N,N-dimethylamino)propyl)-2,7-fluorene)-alt-2,7-(9,9-dioctylfluorene)］ (PF-NR₂)为电子传输层的发光二极管的交流响应特性. 对于结构为ITO/P 关键词： 2')" href="#">PF-NR₂ 聚合物发光二极管 交流阻抗谱 负电容效应     

掺杂不同一维纳米材料的空穴缓冲层对有机电致发光器件性能的影响

对一维纳米材料在空穴缓冲层PEDOT中的作用进行了研究。光致发光表明在PEDOT中掺杂一维纳米材料(二氧化钛纳米管和氧化锌纳米棒)可以提高双层样品PEDOT/MEH-PPV的发光效率。拉曼光谱的结果说明正是由于一维纳米材料与PEDOT之间存在的强相互作用,才减少了PEDOT/MEH-PPV界面上猝灭发光的缺陷态的产生。在以MEH-PPV作为发光层的聚合物电致发光器件中,在PEDOT中掺杂二氧化钛纳米管和氧化锌纳米棒后,器件的最大效率分别提高了2倍和2.5倍。     

体异质结有机太阳能电池性能提高的研究

制备了四种不同结构的有机太阳能电池器件,器件1 ITO/LiF/PEDOT∶PSS/MEH-PPV/C₆₀/Al、器件2 ITO/PEDOT∶PSS/MEH-PPV/C₆₀/Al、器件3 ITO/LiF/PEDOT∶PSS/MEH-PPV∶C₆₀/C₆₀/Al和器件4 ITO/PEDOT∶PSS/MEH-PPV∶C₆₀/C₆₀/Al。测量了它们的电流－电压特性,结果显示在ITO和PEDOT∶PSS之间插入一薄层LiF使得器件性能得到较大提高。其器件1的J_SC和FF比器件2的提高了74%和31%; 器件3的J_SC比器件4的提高了约40%。这主要是由于LiF层有效地抑制了空穴向阳极的传输,并且LiF层在ITO和PEDOT:PSS之间形成了良好的界面特性。因此,这种结构上的改进有效地提高了有机太阳能电池的性能。     

含新型噁二唑类电子传输层的有机发光二极管性能研究

含吡啶基的噁二唑类材料(PDPyDP)作为一种新型的电子传输层被有效地应用于可溶性聚对苯乙炔(MEHPPV)为发光层的双层结构的有机发光二极管器件中,并将其光电性能与MEHPPV的单层结构器件及分别含苯环(PDPDP)和反1,2亚乙烯基(PDVDP)的另外两种二唑类电子传输层的双层结构器件进行比较.EL光谱测量表明,它们的发光均来自于MEHPPV层,而它们相似的器件电流和光输出随驱动电场变化的规律表明这些器件中相似的电荷转移过程,但电致发光阈值电场对于双层结构器件来说低于单层结构器件,而插入PDPyDP层的器件,其阈值电场最低.在电流密度为50mA/cm²时,单层器件及各插入PDVDP、PDPDP和PDPyDP的双层器件的外量子效率相对值分别为3×10^-3%,5×10^-3%,2×10^-2%和0.1%.并分析了插入PDPyDP使器件发光性能提高最为明显的原因.通过将此类器件的结构等作进一步优化,其最佳量子效率可高达1.44%.     

基于量子点和MEH-PPV的白光发光二极管的研究

利用无机纳米材料与有机聚合物材料相结合的方法制备白光发光二极管器件, 研究了蓝光量子点QDs(B)掺杂聚[2-甲氧基-5-(2-乙基己氧基-1, 4-苯撑乙烯撑](MEH-PPV) 复合体系的发光特性及量子点QDs(B) 掺杂浓度(质量分数)不同对器件发光特性的影响. 制备了ITO/PEDOT:PSS/MEH-PPV:QDs(B)/LiF/Al 结构的电致发光器件, 测试了器件的电致发光光谱和电学、光学特性. 当QDs掺杂浓度为40%, 驱动电压为8 V时器件能得到较为理想的白光发射. 同时, 对比研究了非掺杂体系的发光特性, 制备了结构为ITO/PEDOT:PSS/MEH-PPV/QDs(B)/LiF/Al的器件, 掺杂体系相较于非掺杂体系, 器件的最大亮度增大, 启亮电压降低, 并分析了掺杂体系器件性能改善的原因.     

Broadband optical limiting performance of polymer-wrapped carbon nanotubes in the orange-NIR region

Soluble multi-walled carbon nanotubes (MWNTs) have been obtained by noncovalent modification with poly [2-methoxy,5-(2′-ethyl-hexyloxy)-p-phenylene vinylene] (MEH-PPV). For the composite MWNT/MEH-PPV, there is π-π interaction between the MEH-PPV and MWNTs in addition to the wrapping of the polymer. The nonlinear optical transmittance was measured using a nanosecond optical parametric oscillator pumped with a Nd:YAG system. Excellent optical limiting performance of the composite MWNT/MEH-PPV was observed both in the visible region of 590-680 nm and at the wavelength of 1064 nm. By means of time-correlated single-photon counting fluorescence measurement, an explanation based on the nonlinear absorption of MWNT dominated by the intermolecular energy transfer was proposed.     

Study of the interface formed between poly(2-methoxy-5-(2′-ethyl-hexyloxyl)-p-phenylene vinylene) and indium tin oxide in top emission organic light emitting diodes

X-ray photoelectron spectroscopy (XPS) technique have been used to investigate the interface formed between poly(2-methoxy-5-(2′-ethyl-hexyloxyl)-p-phenylene vinylene) (MEH-PPV) and indium tin oxide (ITO) layer in top emission organic light emitting diodes. A weak but noticeable diffusion of indium into the polymer film was observed. Interactions between the diffused metallic atoms with the polymer resulted in the formation of carbon-metal complexes at the interface region. Compared to the ITO/MEH-PPV interface, the penetration of indium into the polymer layer was less important and may be explained by the surface morphology of the polymer film. It was however, a probable factor for fast degradation of devices using this structure.     

MEH-PPV与TiO2共混体系太阳电池性能分析

以MEH-PPV(poly(2-methoxy-5-(2′-ethylhexoxy)-1,4-phenylene vinylene)为电子给体材料(Donor,D), TiO₂纳米线为电子受体材料(Acceptor,A),制成了共混体系太阳电池. 从D/A材料共混体系的紫外可见吸收光谱(UV-vis)、光荧光谱(PL)、器件的电荷传输的光导J-V图等方面,分析了MEH-PPV∶TiO₂体系器件性能变化的原因. 得出了当在纯MEH-PP 关键词： 太阳电池 聚合物 性能     

Increasing the luminous efficiency of an MEH-PPV based PLED using salmon DNA and single walled carbon nanotube

The combined effect of a salmon deoxyribonucleic acid (DNA)-based electron blocking layer and a single walled carbon nanotube (SWCNT) composite-based electron transport layer on the performance of a poly[2-methoxy-5-(2′-ethyl-hexyloxy)-1,4-phenylene vinylene] (MEH-PPV) polymer light emitting diode (PLED) has been examined. The SWCNT network in the composite layer improves electron injection from cathode and the DNA blocks these high mobility electrons at the electron blocking layer-polymer interface, leading to high luminance from the device. The luminous efficiency of the PLED is increased ∼20 times compared to that of a PLED using only MEH-PPV.     

Photovoltaic characteristics of hybrid MEH-PPV-nanoparticles compound

Organic solar cell research has vastly developed in recent years. These organic solar cells however are still limited to low power conversion efficiencies. This has led to the generation of photovoltaic cells based on hybrid nanoparticle-organic polymer materials. The hybrid solar cell has the potential of bridging the efficiency gap which is present in organic and inorganic semiconductor materials. This paper focuses on characterization of fabricated hybrid active layer consisting of organic polymer infused with semiconductor nanoparticles. The active layer was deposited on the substrate using the spin coating technique. Materials used in the active layer are poly (2-methoxy, 5-(2-ethyl hexyloxy) p-phenyl vinylene) MEH-PPV, cadmium telluride (CdTe) and cadmium sulphide (CdS). The fabricated solar cells with active layer of MEH-PPV only were found to have a power conversion efficiency of 0.1% for 1 W, hybrid cell with active layer of MEH-PPV/CdTe has power conversion efficiency of 0.15% for 1 W and hybrid cell with active layer of MEH-PPV/CdTe/CdS has power conversion efficiency of 0.18% for 1 W.     

聚苯胺在聚合物发光二极管中的空穴传输作用

报道了聚苯胺中间氧化态(emeraldine base form PANI-EB)空穴传输层对以PPV衍生物(PTA-PPV,PTA-DMPPV和MEH-PPV)为发光层和Alq₃为电子传输层构成的多层结构的发光二极管的影响。实验结果表明,在器件中PANI-EB空穴层的引入能有效地降低器件的启亮电压和提高器件的发光亮度,其影响程度依赖于PPV衍生物的结构。     

ZnO纳米棒在聚［2-甲氧基-5-（2-乙基-己氧基）-1，4-苯撑乙烯撑］固态阴极射线发光器件中的应用研究

利用ZnO纳米棒阵列场发射电极,以SiO₂做为电子加速层制备了固态阴极射线器件,发光层为聚［2-甲氧基-5-（2-乙基-己氧基）-1,4-苯撑乙烯撑］（MEH-PPV）,在交流驱动下得到了MEH-PPV的固态阴极射线发光,探测到了长波峰和短波峰的发射,并和无电子加速层的器件做了比较,证明混合激发模式下的器件在长波长的发光亮度更大. 关键词： 固态阴极射线 ZnO纳米棒阵列 电子加速 电致发光     

Effect of different metal-backed waveguides on amplified spontaneous emission

We investigate the effect of a metallic electrode on the ability for poly[2-methoxy-5-(2’-ethylhexyloxy)-1,4phenylene vinylene](MEH-PPV) film to undergo amplified spontaneous emission(ASE).The threshold of the device with Ag cladding is about 10 times greater than that of a metal-free device,but metal such as Al completely shuts off ASE.The ASE recurs when a thin spacer layer,such as a few nanometers of SiO 2,is introduced between the MEH-PPV film and the Al cladding.Compared with the Cu or Al electrode,the Ag cladding is most suited to serve as an electrode with its low optical loss due to its high work-function and reflectivity.     

有机薄膜晶体管驱动聚合物发光二极管研究

研究了有机薄膜晶体管(OTFT)与聚合物发光二极管(PLED)集成制备技术和相关物理问题.OTFT结构为栅极钽(Ta)/绝缘层五氧化二钽(Ta2O5)/有源层并五苯(Pentacene)/源漏极金(Au);PLED器件结构为ITO/PEDOT:PEO(polyethylene oxide)/P-PPV或MEH-PPV/Ba/Al.PEDOT:PEO,P-PPV和MEH-PPV薄膜层均采用丝网印刷技术,实现了OTFT与PLED器件集成发光.其中OTFT器件的阈值电压为-7V,迁移率为0.91cm2/(V.s),并通过OTFT驱动得到以P-PPV和MEH-PPV为发光层的PLED器件的发光亮度分别达到124和26cd/m2,电流效率分别为12.4和1.1cd/A.利用丝网印刷技术可以有效控制高分子薄膜的沉积区域,实现功能器件的集成.     

电场诱导空穴注入缓冲层PEDOT：PSS取向对OLED发光性能的影响

实验中以PEDOT:PSS在ITO基片上旋涂作为空穴传输层,并且在旋涂PEDOT:PSS的过程中在与ITO玻璃平面垂直的方向施加一个诱导聚合物取向的高压电场,试验着重研究了所加电场强度对双层器件:ITO/PEDOT:PSS/MEH-PPV/Al器件性能的影响。测试结果表明,旋涂时所加电场的大小对器件的发光强度和起亮电压都有明显的影响。随着所加电场的增大,器件发光强度明显增加,起亮电压减小。由此表明:在高电场作用下,聚合物分子链沿电场方向发生了取向,而且随着电场增强这种取向作用会表现得越明显,并且在PEDOT:PSS膜表层会形成一个梯度变化的PSS聚集,使得从ITO到MEH-PPV的功函数逐渐上升,降低空穴注入势垒,增强了空穴的注入效率。     

TBPe与MEH-PPV共掺杂的有机电致发光器件的优化研究

采用有机小分子TBPe（2,5,8,11-tetratertbutylperylene）以不同比例掺入MEH-PPV（poly ）作为发光层,研究了TBPe不同掺杂比例对器件性能的影响,进而对发光强度进行优化。对于所制备的ITO/PEDOT：PSS/MEH-PPV/TBPe/Al有机电致发光器件,TBPe的最优蒸镀厚度为0.5 nm,其发光强度相对于标准器件提高了325%。ITO/PEDOT：PSS/MEH-PPV：TBPe/TBPe/Liq/Al有机电致发光器件的最优掺杂比例为MEH-PPV：TBPe=100：30（质量比）,其发光亮度相比于未掺杂器件提高了44%。在上述器件的基础上增加Alq₃层提高电子注入,分别制作了Liq和LiF作为修饰层的ITO/PEDOT：PSS/MEH-PPV：TBPe/TBPe/Alq₃/Liq/Al和ITO/PEDOT：PSS/MEH-PPV：TBPe/TBPe/Alq₃/LiF/Al多层器件,发光亮度分别达到4 162 cd/m²和4 701 cd/m²。所有器件的电致发光波长均为580 nm,为MEH-PPV的发光,TBPe的掺杂对MEH-PPV的发光起到了增强作用。     

Enhanced luminance of MEH-PPV based PLEDs using single walled carbon nanotube composite as an electron transporting layer

An efficient electron transporting layer (ETL) based on single walled carbon nanotube (SWCNT) composites has been developed for poly [2-methoxy-5-(2′-ethyl-hexyloxy)-1,4-phenylene vinylene] (MEH-PPV) based orange polymer light emitting diodes (PLEDs) and its effect on the performance of PLEDs has been examined. It is observed that with increase in SWCNT concentration, in ETL, the luminance and luminous efficiency of the PLEDs increase (about 5 times increase in luminance is observed at 5% w/w SWCNT concentration). The SWCNTs present in the MEH-PPV ETL boost the mobility of electrons injected from the cathode towards the emissive layer by establishing highly conducting percolation paths. This balances the concentration of holes and electrons in the emissive layer, which leads to enhanced emission from the PLEDs.