In‐line preconcentration capillary zone electrophoresis for the analysis of haloacetic acids in water

Two in‐line enrichment procedures (large volume sample stacking (LVSS) and field amplified sample injection (FASI)) have been evaluated for the CZE analysis of haloacetic acids (HAAs) in drinking water. For LVSS, separation on normal polarity using 20 mM acetic acid–ammonium acetate (pH 5.5) containing 20% ACN as BGE was required. For FASI, the optimum conditions were 25 s hydrodynamic injection (3.5 kPa) of a water plug followed by 25 s electrokinetic injection (?10 kV) of the sample, and 200 mM formic acid–ammonium formate buffer at pH 3.0 as BGE. For both FASI and LVSS methods, linear calibration curves (r²>0.992), limit of detection on standards prepared in Milli‐Q water (49.1–200 μg/L for LVSS and 4.2–48 μg/L for FASI), and both run‐to‐run and day‐to‐day precisions (RSD values up to 15.8% for concentration) were established. Due to the higher sensitive enhancement (up to 310‐fold) achieved with FASI‐CZE, this method was selected for the analysis of HAAs in drinking water. However, for an optimal FASI application sample salinity was removed by SPE using Oasis WAX cartridges. With SPE‐FASI‐CZE, method detection limits in the range 0.05–0.8 μg/L were obtained, with recoveries, in general, higher than 90% (around 65% for monochloroacetic and monobromoacetic acids). The applicability of the SPE‐FASI‐CZE method was evaluated by analyzing drinking tap water from Barcelona where seven HAAs were found at concentration levels between 3 and 13 μg/L.     

Simultaneous determination of nitrite and nitrate in human plasma by on-capillary preconcentration with field-amplified sample stacking

A simple method for the determination of nitrite and nitrate in human plasma has been developed using CZE with minimal sample preparation. Field‐amplified sample stacking (FASS) was used to achieve submicromolar detection by dilution of the plasma sample with deionized water. In CZE, the separation of nitrite and nitrate was achieved within 10 min without adding EOF modifier. The optimal condition was achieved with 50 mM phosphate buffer at pH 9.3. The ninefold diluted plasma samples were injected hydrodynamically for 40 s into a 60 cm×75 μm id uncoated fused‐silica capillary. The separation voltage was 20 kV (negative potential) and UV detection was performed at 214 nm. The linearity curves for nitrite and nitrate were obtained by the standard addition method. The estimated LODs for nitrite and nitrate in ninefold diluted plasma sample were 0.05 and 0.07 μM, respectively. The LODs for nitrite and nitrate in original plasma samples were 0.45 and 0.63 μM. The intra‐ and inter‐day precisions for both analytes were <2.6% and the recovery ranged between 92.3 and 113.3%. It was found that nitrite was more stable than nitrate in the plasma after the sample preparation. This proposed method was applied to a number of human plasma samples and the measured nitrite and nitrate concentrations in human plasma were consistent with the literature ranges.     

Online preconcentration by electrokinetic supercharging for separation of endocrine disrupting chemical and phenolic pollutants in water samples

Online preconcentration using electrokinetic supercharging (EKS) was proposed to enhance the sensitivity of separation for endocrine disrupting chemical (methylparaben (MP)) and phenolic pollutants (2‐nitrophenol (NP) and 4‐chlorophenol (CP)) in water sample. Important EKS and separation conditions such as the concentration of BGE; the choice of terminating electrolyte (TE); and the injection time of leading electrolyte (LE), sample, and TE were optimized. The optimum EKS‐CE conditions were as follows: BGE comprising of 12 mM sodium tetraborate pH 10.1, 100 mM sodium chloride as LE hydrodynamically injected at 50 mbar for 30 s, electrokinetic injection (EKI) of sample at –3 kV for 200 s, and 100 mM CHES as TE hydrodynamically injected at 50 mbar for 40 s. The separation was conducted at negative polarity mode and UV detection at 214 nm. Under these conditions, the sensitivity of analytes was enhanced from 100‐ to 737‐fold as compared to normal CZE with hydrodynamic injection, giving LOD of 4.89, 5.29, and 53 μg/L for MP, NP and CP, respectively. The LODs were adequate for the analysis of NP and CP in environmental water sample having concentration at or lower than their maximum admissible concentration limit (240 and 2000 μg/L for NP and CP). The LOD of MP can be suitable for the analysis of MP exists at mid‐microgram per liter level, even though the LOD was slightly higher than the concentration usually found in water samples (from ng/L to 1 μg/L). The method repeatabilities (%RSD) were in the range of 1.07–2.39% (migration time) and 8.28–14.0% (peak area).     

Determination of Naphthalenesulfonate Isomers in Industrial Effluents and River Water by Solid‐Phase Extraction and Capillary Zone Electrophoresis

This work presents a method to separate polar naphthalenesulfonate (NS) isomers by capillary zone electrophoresis (CZE) with ultraviolet detection in industrial effluents and river water samples. The method involves extraction of samples by a polystyrene‐divinylbenzene copolymer (PS‐DVB) solid‐phase extraction (SPE) cartridge. The most effective CZE separation conditions were obtained in 20 mM borate buffer with 30% acetonitrile at pH 9.0 and 30 °C. The method proposed herein provides a high precision and sensitivity for NS isomers, to quantitation at ≤ 1.0 μg/L in 200 mL of the water samples. Recovery of the NS isomers in spiked water samples ranged from 73% to 87% while RSD ranging from 5.6 to 9.7%. The analysis of industrial effluents and river water samples was performed and naphthalene‐2‐sulfonate was found as a major pollutant. The difficulties in quantitating and identifying analytes in complex environmental samples can be resolved by using an internal standard response factor to calculate concentrations and relative migration times for peak confirmation.     

Electrokinetic supercharging focusing in capillary zone electrophoresis of weakly ionizable analytes in environmental and biological samples

Five non‐steroidal anti‐inflammatory drugs, naproxen, fenoprofen, ketoprofen, diclofenac and piroxicam, were separated and analyzed by electrokinetic supercharging in CZE. Three different setups of the ITP technique were assayed for the separation and preconcentration of these five non‐steroidal anti‐inflammatory drugs. For the setup that gave the best results, we evaluated the influence of different parameters on separation and preconcentration efficiency such as sample pH, concentration of the leading stacker, BGE composition, electrokinetic injection time, composition and hydrodynamic injection of the solvent plug and of the terminating stacker. In the selected setup, the BGE (10 mM Na₂B₄O₇ + 50 mM NaCl in 10% of MeOH aqueous solution) contained the leading electrolyte while the terminating electrolyte, hydrodynamically injected after the sample (50 mbar×12 s), was 50 mM of CHES. Prior to sample injection at (700 s at −2 kV) a short plug of MeOH (50 mbar ×3 s) was hydrodynamically injected. The results show that this strategy enhanced detection sensitivity 2000‐fold compared with normal hydrodynamic injection, providing detection limits of 0.08 μg/L for standard samples with good repeatability (values of relative standard deviation, %RSD < 1.03%). Method validation with river water samples and human plasma demonstrated good linearity, with detection limits of 0.9 and 2 μg/L for river water samples and human plasma samples, respectively (as well as satisfactory precision in terms of repeatability and reproducibility).     

Analysis of polyphenols in white wine by CZE with amperometric detection using carbon nanotube-modified electrodes

A method for the simultaneous detection of five polyphenols (caffeic, chlorogenic, ferulic and gallic acids and (+)-catechin) by CZE with electrochemical detection was developed. Separation of these polyphenols was performed in a 100 mM borate buffer (pH 9.2) within 15 min. Under optimized separation conditions, the performance of glassy carbon (GC) electrodes modified with multiwalled carbon nanotube layer obtained from different dispersions was examined. GC electrode modified with a dispersion of multi-walled carbon nanotubes (CNT) in polyethylenimine has proven to be the most suitable CNT-based electrode for its application as amperometric detector for the CZE separation of the studied compounds. The excellent electrochemical properties of this electrode allowed the detection of the selected polyphenols at +200 mV and improved the efficiency and the resolution of their CZE separation. Limits of detection below 3.1 μM were obtained with linear ranges covering the 10?? to 10?? M range. The proposed method has been successfully applied for the detection (ferulic, caffeic and gallic acids and (+)-catechin) and the quantification (gallic acid and (+)-catechin) of polyphenols in two different white wines without any preconcentration step. A remarkable signal stability was observed on the electrode performance despite the presence of potential fouling substances in wine.     

Investigation of in-line solid-phase extraction capillary electrophoresis for the analysis of drugs of abuse and their metabolites in water samples

In this study, in‐line solid‐phase extraction (SPE) was used as an enrichment technique in combination with CE for the preconcentration and separation of 2‐ethylidene‐1,5‐dimethyl‐3,3‐diphenylpyrrolidine (EDDP), cocaine (COC), codeine (COD) and 6‐acetylmorphine (6AM). The separation buffer (BGE) used was 80 mM disodium phosphate anhydrous and 6 mM of HCl (final BGE pH of 3). The SPE extractor consists of a small segment of capillary filled with Oasis HLB sorbent and inserted into the inlet section of the electrophoretic capillary. Different parameters affecting preconcentration were evaluated, such as sample pH, the volume of the elution plug and sample injection time. The detection limits (LODs) reached for standard samples by in‐line SPE‐CE‐UV ranged between 50 and 200 ng/L, with sensitivity enhancement factors ranging from 2300 to 5300. Reproducibility values (expressed in terms of relative standard deviation) were below 7.6% for standard samples. This is a simple and an effective method for the determination of the studied drugs of abuse and their metabolites. The applicability of the developed method was demonstrated in tap and river water samples which were directly analyzed without any off‐line pretreatment. Analytical parameters were evaluated and LODs were between 70 and 270 ng/L with relative recoveries between 85 and 97%.     

On‐line solid phase extraction CZE for the simultaneous determination of lanthanum and gadolinium at picogram per liter levels

A non‐specific on‐line method is presented for the extraction and preconcentration of two rare earth elements using a microcartridge containing C₁₈‐derivatized silica particles prior to their analysis by CZE. The microcartridge, named analyte concentrator, was coupled on‐line to the inlet of the separation capillary (fused‐silica (FS) capillary, 75 μm id ×12 cm from the inlet to the microcartidge and 37 cm from the microcartridge to the detector). The reversed‐phase sorbent quantitatively retained gadolinium (Gd) and lanthanum (La) as 2‐(5‐bromo‐2‐pyridylazo)‐5‐diethylaminophenol complexes in the presence of non‐ionic micelles of polyethylene glycol tert‐octylphenyl ether, enabling sample clean‐up and concentration enhancement with minimum sample handling. The rare earth elements chelates were released from the sorbent with methanol and then analyzed by CZE with diode array detection. A background electrolyte of 20 mM sodium tetraborate containing 8% ACN, pH 9.0, was found to be optimal for the separation of metal chelates. The concentration limits of detection were lowered to picogram per liter levels (20 pg/L for La and 80 pg/L for Gd). A 1000‐fold improvement in concentration sensitivity for La‐ and Gd‐2‐(5‐bromo‐2‐pyridylazo)‐5‐diethylaminophenol complexes with respect to CZE without preconcentration was reached.     

Large-volume sample stacking for the analysis of seven beta-lactam antibiotics in milk samples of different origins by CZE

A method for the simultaneous determination of eight beta-lactam antibiotics (nafcillin, cloxacillin, oxacillin, dicloxacillin, ampicillin, amoxicillin, and penicillin G) in fortified milk samples of different origins has been proposed by using CZE with diode-array detection (CZE-DAD). Optimum separation was obtained on a 64.5 cm x 75 microm bubble cell capillary using 175 mM Tris buffer with 20% ethanol at pH 8.0. Methylparaben has been used as an internal standard (IS). Taking into account the lack of sensitivity of the UV-Vis detection, a solvent extraction/SPE method was applied for off-line preconcentration and sample cleanup, and also an on-line preconcentration methodology, such as large-volume sample stacking (LVSS) with polarity switching, was developed, providing LODs ranging from 2 to 10 microg/L. The method permits the quantification of these residues below the levels established in milk by the EU Regulation. Satisfactory recoveries ranging from 86 to 93% were also obtained in milk samples of different origins.     

Capillary Zone Electrophoresis of Eleven Priority Phenols with Amperometric Detection

A scheme for separation and detection of eleven priority phenols using capillary zone electrophoresis (CZE) coupled with amperometric detection is described. With a capillary of I.D. 50 μm and length 62.5 cm at 9 kV and an electrophoretic buffer of 20 mM CHES (pH 10.1), complete separation of the eleven compounds was achieved in less than 17 min. Amperometric detection was carried out using a carbon fiber microelectrode of diameter 9 μm inserted into the end of the detection capillary. Linearity over two orders of magnitude was generally obtained for the eleven priority phenols. With an electrode potential+1.10 V (vs. Ag/AgCl reference), the concentration limits of detection were in the sub-ppm (10^?6 M) level. This method was successfully applied to analysis of priority phenols in industrial waste water.     

Determination of phenolic acids in plant extracts using CZE with on‐line transient isotachophoretic preconcentration

A novel transient ITP–CZE for preconcentration and determination of seven phenolic acids (caffeic acid, cinnamic acid, p‐coumaric acid, ferulic acid, protocatechuic acid, syringic acid, and vanilic acid) was developed and validated. Effects of several factors such as control of EOF, pH and buffer concentration, addition of organic solvents and CDs, and conditions for sample injection were investigated. Sample self‐stacking was applied by means of induction of transient ITP, which was realized by adding sodium chloride into the sample. The CZE was realized in 200 mM borate buffer ( 9.2) containing 37.5% methanol, 0.001% hexadimethrine bromide, and 15 mM 2‐hydroxypropyl‐β‐CD. Under the optimal conditions for analysis, analytes were separated within 20 min. Linearity was tested for each compound in the concentration range of 0.1–10 μg/mL (R = 0.9906–0.9968) and the detection limits (S/N = 3) ranged from 11 ng/mL (protocatechuic acid) to 31 μg/mL (syringic acid). The validated method was applied to the ethanolic extract of Epilobium parviflorum, Onagraceae. The method of SPE was used for the precleaning of the sample.     

Simultaneous determination of deoxycytidine diphosphate and deoxycytidine triphosphate by capillary electrophoresis with transient isotachophoretic stacking: a sensitive monitoring method for ribonucleotide reductase activity

A simple and rapid capillary electrophoretic method was developed for simultaneous determination of sub‐micromolar 2′‐deoxycytidine 5′‐diphosphate (dCDP) and 2′‐deoxycytidine 5′‐triphosphate (dCTP) levels in enzyme assays without using radioactively labeled substrates. The separation was performed at 25°C using MES in the BGE as the terminating ion, the chloride ions in the sample buffer as the leading ion, and PEG 4000 in the BGE as the EOF suppressor for sample stacking by transient isotachophoresis (tITP). Several parameters affecting the separation were investigated, including the pH of the BGE, the concentration of sodium chloride in the sample buffer, and the concentrations of MES and PEG 4000 in the running buffer. Good separation with high separation efficiency was achieved within 6 min under optimal conditions. In comparison with the simple CZE method, the present tITP‐CZE method enabled a 150‐fold increase in the injection time without any decrease in resolution and the sensitivity was enhanced up to two orders of magnitude with the new method. The linear range of the method was 0.1–10 μM for dCDP and dCTP. The limits of detection of dCDP and dCTP were 85 and 73 nM, respectively. The proposed method was successfully applied for the activity assay of ribonucleotide reductase from Hep G2 and Sf9 cells.     

Determination of pesticides in wine using micellar electrokinetic chromatography with UV detection and sample stacking

In this work, the analysis of a group of four fungicides (pyrimethanil, nuarimol, procymidone and cyprodinil) and one insecticide (pirimicarb) by micellar electrokinetic chromatography (MEKC) with UV detection using the on-line preconcentration strategy called reversed electrode polarity stacking mode (REPSM) is proposed. After optimisation, an adequate separation electrolyte for the separation and stacking of these pesticides was obtained which consisted of 100 mM borate, 60 mM sodium dodecyl sulphate (SDS), at pH 9.0 and 2% 2-propanol. The use of this running buffer together with the REPSM preconcentration method provided limits of detection (LODs) between 38.3 and 241 microg/L. In order to apply the developed methodology for the analysis of these pesticides in wine samples, several off-line preconcentration strategies (mainly, solid-phase extraction, SPE, and solid-phase microextraction, SPME) were tested. Although the use of a SPE procedure, optimized in this work for water samples, using Oasis HLB cartridges, provided mean recovery values between 79 and 100% for spiked water samples, it could not be applied to the extraction of these pesticides from wine samples due to high interference from the sample matrix. However, the use of a SPME procedure using polydimethylsiloxane/divynilbenzene (PDMS/DVB) fibers allowed the selective extraction of four of the five pesticides which could be perfectly determined. The final combination of the off-line SPME and on-line REPSM preconcentration strategies allowed obtaining LODs between 17.6 and 32.3 microg/L.     

Separation and Detection of Nitrophenols at Capillary Electrophoresis Microchips with Amperometric Detection

A miniaturized analytical system for the separation and amperometric detection of toxic nitrophenols, based on the coupling of a micromachined capillary electrophoresis (CE) chip with a glassy carbon detector is described. This microsystem enables a rapid (120 s/sample) simultaneous determination of five priority nitrophenolic pollutants (2‐nitrophenol, 3‐nitrophenol, 4‐nitrophenol, 2,4‐dinitrophenol, and 2‐methyl‐4,6‐dinitrophenol). These compounds can be detected down to the 1×10^?5 M level using a 15 mM phosphate buffer pH 7.2 (containing 1.3 mM α‐cyclodextrin) as running solution on 77 mm long microchannel by applying a separation voltage of 3000 V and a negative potential of ?0.7 V (vs. Ag /AgCl wire). Applicability to ground water samples was demonstrated.     

Optimization of CZE for analysis of phytochemical bioactive compounds

Advantages of CZE such as high efficiency, low cost, short analysis time, and easy implementation result in its wide applications for analysis of phytochemical bioactive compounds (e.g. flavonoids, alkaloids, terpenoids, phenolic acid, saponins, anthraquinones and coumarins). However, several aspects, including sample preparation, separation, and detection have significant effects on CZE analysis. Therefore, optimization of these procedures is necessary for development of the method. In this review, sample preparation such as extraction method and preconcentration, separation factors including buffer type, concentration and pH, additives, voltage and temperature, as well as detection, e.g. direct and indirect UV detection, LIF and MS were discussed for optimization of CZE analysis on phytochemical bioactive compounds. The optimized strategies were also reviewed.     

Determination of Substance P by capillary zone electrophoresis in rat brain

In the complex neuronal network, chemical messengers like neuropeptides play a key role in signaling. To understand the mechanism of signaling, it is necessary to analyze the levels of neuropeptides from biological sources, which is important for neuroscience research. In the present work, a detailed investigation of the capillary zone electrophoresis (CZE) method was carried out to detect and quantify Substance P (SP), a bioactive neuropeptide, in rat brain tissues. The method involves specifically, a combination of solid phase extraction and immunoprecipitation prior to the CZE quantification. In this procedure, antibodies are used to capture the analyte of interest before the separation by CZE. Different separation parameters like buffer type, concentration, pH and applied voltage were the steps taken to study and achieve high efficiency CZE separation. CZE analysis was performed in an untreated fused-silica capillary column (35 cm×75 μm i.d.) and 185 nm wavelength using 100 mM phosphate buffer (pH 2.5) as a separation buffer. Electrophoresis in acidic mode and successive washing procedures solved the adsorption problem. The method provides a rapid analysis time of less than 15 min with 3.91% of RSD. Simultaneously, SP was quantified by Matrix Assisted Laser Desorption Ionization-Time of Flight-Mass Spectrometry (MALDI-TOF-MS) and compared with CZE data. Starting from milligram amounts of brain tissue, the method allowed the detection of low picomole amounts of SP and the combined use of CZE and MALDI-TOF-MS was a success in quantification in this study.     

Determination of sulfonylurea herbicides in soil extracts by solid-phase extraction and capillary zone electrophoresis

Summary Sulfonylurea herbicides in soil extracts were concentrated using off-line solid-phase extraction (SPE), and determined by capillary zone electrophoresis (CZE) and UV detection. The method involves extraction of soils with 0.1 M NaHCO₃ solution and subsequent preconcentration by using C₁₈ cartridges prior to separation of the pesticide using CZE. The results show that a C₁₈ cartridge is suitable for the purification of sulfonylurea herbicides in soil extracts with the recoveries ranging from 65–103%. The separation conditions affecting the resolution and detection sensitivity was systematically investigated. The sulfonylureas were resolved well using 30 mM sodium acetate (NaAc)/acetic acid (HAc)+10% acetonitrile (ACN) buffer at pH 4.80. The calibration plots for the test solutes in the concentration of 0.2–50 mg L⁻¹ were linear with detection limits in the range of 0.05–0.10 mgL⁻¹. The proposed method has been successfully demonstrated for the determination of sulfonylurea herbicides in soil samples.     

A capillary zone electrophoresis for determination of thiolic peptides in biological samples

A new method to improve the analyses of thiolic peptides (cysteine, γGlu-Cys, glutathione, phytochelatins and desglycyl-phytochelatins) derivatized with monobromobimane (mBrB) in complex biological samples by CZE is described. The method involves a SPE using Sep-Pak Light C18 Cartridges after derivatization and a later CZE analysis. Elution of mBrB-thiols was achieved with 10 mM HCl + 70% methanol v/v in deionised water. Electrophoretic parameters, such as BGE pH and concentration, different organic additives (methanol and trifluoroethanol), applied voltage and capillary length were studied in order to establish suitable analytical conditions. Optimum separation of the mBrB-thiolic peptides was obtained with 100 mM sodium borate buffer at pH 7.60. The electrophoretic conditions were +15 kV, capillary length of 90 cm from inlet to detector (98 cm total length, 50 μm ID), samples were loaded into the capillary by hydrodynamic injection (50 mbar, 20 s) and detection was performed at 390 nm. The improved method showed good reproducibility, linearity and sensitivity. The LODs and LOQs estimated using a standard of GSH were 1.41 and 4.69 μM respectively.     

Determination of UV filters in river water samples by in‐line SPE‐CE‐MS

The use of SPE coupled in‐line to CE using electrospray MS detection (in‐line SPE‐CE‐ESI‐MS) was investigated for the preconcentration and separation of four UV filters: benzophenone‐3, 2,2‐dihydroxy‐4‐methoxybenzophenone, 2,4‐dihydroxybenzophenone and 2‐phenylbenzimidazole‐5‐sulphonic acid. First, a CE‐ESI‐MS method was developed and validated using standard samples, obtaining LODs between 0.06 μg/mL and 0.40 μg/mL. For the in‐line SPE‐CE‐ESI‐MS method, three different sorbents were evaluated and compared: Oasis HLB, Oasis MCX, and Oasis MAX. For each sorbent, the main parameters affecting the preconcentration performance, such as sample pH, volume, and composition of the elution plug, and sample injection time were studied. The Oasis MCX sorbent showed the best performance and was used to validate the in‐line SPE‐CE‐ESI‐MS methodology. The LODs reached for standard samples were in the range between 0.01 and 0.05 ng/mL with good reproducibility and the developed strategy provided sensitivity enhancement factors between 3400‐fold and 34 000‐fold. The applicability of the developed methodology was demonstrated by the analysis of UV filters in river water samples.     

Separation of natural antioxidants using PDMS electrophoresis microchips coupled with amperometric detection and reverse polarity

This report describes the use of PDMS ME coupled with amperometric detection for rapid separation of ascorbic, gallic , ferulic, p‐coumaric acids using reverse polarity. ME devices were fabricated in PDMS by soft lithography and detection was accomplished using an integrated carbon fiber working electrode aligned in the end‐channel configuration. Separation and detection parameters were investigated and the best conditions were obtained using a run buffer consisting of 5 mM phosphate buffer (pH 6.9) and a detection voltage of 1.0 V versus Ag/AgCl reference electrode. All compounds were separated within 70 s using gated injection mode with baseline resolution and separation efficiencies between 1200 and 9000 plates. Calibration curves exhibited good linearity and the LODs achieved ranged from 1.7 to 9.7 μM. The precision for migration time and peak height provided maximum values of 4% for the intrachip studies. Lastly, the analytical method was successfully applied for the analysis of ascorbic and gallic acids in commercial beverage samples. The results achieved using ME coupled with amperometric detection were in good agreement with the values provided by the supplier. Based on the data reported here, the proposed method shows suitability to be applied for the routine analysis of beverage samples.