Raman scattering and room temperature ferromagnetism in Co-doped SrTiO3 particles

Raman scattering has been used to study the influence of cobalt, an effective dopant to obtain SrTiO₃ magnetic oxide, on the lattice dynamics of SrTiO₃. It is found that Co doping increases the lattice defects and induces a Raman vibration mode of 690 cm⁻¹. On the other hand, the ferromagnetism dependence on the x and annealing temperature was clearly and coherently observed in SrTi_1−xCo_xO₃ (x = 0, 0.01, 0.03 and 0.05) nanoparticles. It is found that the ferromagnetism of SrTi_1−xCo_xO₃ nanoparticles is weakly related to crystal deformation and oxygen vacancies in SrTiO₃. So, F-center model can explain the origin of the ferromagnetism in the prepared Co-doped SrTiO₃ samples. At the same time, the finding of large room-temperature ferromagnetism (1.6 emu/g) in this system would stimulate further interest in the area of more complicated ternary oxides.     

Effect of oxygen vacancy and dopant concentration on the magnetic properties of high spin Co doped TiO2 nanoparticles

Co doped TiO₂ nanoparticles have been synthesized by a simple sol-gel route taking 7.5, 9.5 and 10.5 mol% of cobalt concentration. Formation of nanoparticles is confirmed by XRD and TEM. Increase in d-spacing occurs for (0 0 4) and (2 0 0) peak with increase in impurity content. Valence states of Co and its presence in the doped material is confirmed by XPS and EDX. The entire vacuum annealed samples show weak ferromagnetism. Increased magnetization is found for 9.5 mol% but this value again decreases for 10.5 mol% due to antiferromagnetic interactions. A blocking temperature of 37.9 K is obtained, which shows shifting to high temperature as the dopant concentration is increased. The air annealed sample shows only paramagnetic behavior. Temperature dependent magnetic measurements for the air annealed sample shows antiferromagnetic behavior with a Curie-Weiss temperature of −16 K. Here we report that oxygen vacancy and cobalt aggregates are a key factor for inducing ferromagnetism-superparamagnetism in the vacuum annealed sample. Appearance of negative Curie-Weiss temperature reveals the presence of antiferromagnetic Co₃O₄, which is the oxidation result of metallic Co or cobalt clusters present on the host TiO₂.     

On the room-temperature ferromagnetism in (ZnO)0.98(MnO2)0.02

Room-temperature ferromagnetism (RTFM) is investigated in the polycrystalline bulk (ZnO)_0.98(MnO₂)_0.02 samples prepared by a modified solid-state sintering route. Successive sintering of a sample was carried out in air at different temperatures in the range of 400-1000 °C. The study of magnetization and phase-investigation in the sample was carried out after each sintering step. The progressive suppression of impurities and the consequent reduction in RTFM is clearly observed in the samples with increase in the sintering temperature up to 800 °C. The subsequent successive sintering of the (ZnO)_0.98(MnO₂)_0.02 sample up to 1000 °C yields fully paramagnetic sample exhibiting wurtzite structure. The studies support the conjecture (Kundaliya et al., Nat. Mater. 3 (2004) 709 [18]) that RTFM in this system has an origin related to a randomly distributed impurity phase produced by local dissolution of ZnO and MnO₂.     

Effect of annealing temperature on structure, magnetic properties and optical characteristics in Zn0.97Cr0.03O nanoparticles

The Cr-doped zinc oxide (Zn_0.97Cr_0.03O) nanoparticles were successfully synthesized by sol-gel method. The relationship between the annealing temperature (400 °C, 450 °C, 500 °C and 600 °C) and the structure, magnetic properties and the optical characteristics of the produced samples was studied. The results indicate that Cr (Cr³⁺) ions at least partially substitute Zn (Zn²⁺) ions successfully. Energy dispersive spectroscopy (EDS) measurement showed the existence of Cr ion in the Cr-doped ZnO. The samples sintered in air under the temperature of 450 °C had single wurtzite ZnO structure with prominent ferromagnetism at room temperature, while in samples sintered in air at 500 °C, a second phase-ZnCr₂O₄ was observed and the samples were not saturated in the field of 10000 Oe. This indicated that they were mixtures of ferromagnetic materials and paramagnetic materials. Compared with the results of the photoluminescence (PL) spectra, it was reasonably concluded that the ferromagnetism observed in the studied samples was originated from the doping of Cr in the lattice of ZnO crystallites.     

Synthesis and characterization of room-temperature ferromagnetism in Fe- and Ni-co-doped In2O3

Observation of room-temperature ferromagnetism in Fe- and Ni-co-doped In₂O₃ samples (In_0.9Fe_0.1−xNi_x)₂O₃ (0?x?0.1) prepared by citric acid sol-gel auto-igniting method is reported. All of the samples with intermediate x values are ferromagnetic at room-temperature. The highest saturation magnetization (0.453 μ_B/Fe+Ni ions) moment is reached in the sample with x=0.04. The highest solubility of Fe and Ni ions in the In₂O₃ lattice is around 10 and 4 at%, respectively. The 10 at% Fe-doped sample is found to be weakly ferromagnetic, while the 10 at% Ni-doped sample is paramagnetic. Extensive structure including Extended X-ray absorption fine structure (EXAFS), magnetic and magneto-transport including Hall effects studies on the samples indicate the observed ferromagnetism is intrinsic rather than from the secondary impurity phases.     

Magnetic properties, microstructures and magnetoresistance effect in Co/Alq3 granular films

A series of Co_x(Alq₃)_1−x granular films were prepared using the co-evaporating technique. HRTEM images show typical characteristics of granular films with the average size of 2-5 nm. It shows a gradual change from superparamagnetism to ferromagnetism with the rise of x. Negative magnetoresistance (MR) was observed, reaching −5.31% in x=0.44 sample at 30 K under the field of 10 kOe. The concentration dependence of MR and resistivity is also investigated. The inter-particle tunneling is believed to account for the negative MR effect.     

High sensitivity of magnetism of the “114” ferrimagnet CaBaCo4O7 to stoichiometry deviation

The effect of oxygen/cobalt off-stoichiometry upon magnetism in CaBaCo₄O₇ has been investigated. It is shown that the oxides CaBaCo₄O_7+δ and CaBaCo_4−xO_7−δ (0≤x≤0.20) synthesized below 1100 °C in air exhibit phase separation, where ferrimagnetic regions with T_C~56 K to 64 K coexist with regions of magnetic clusters. The latter are detected from ac-susceptibility measurements, which show various frequency dependent peaks at ~14–20 K, 37 K, and 45 K, depending on the stoichiometry. The origin of this phenomenon is attributed to the great sensitivity of the material to oxidation as the synthesis of temperature is lowered, leading to the introduction of additional Co³⁺ cations, with respect to the ideal formula CaBaCo₂²⁺Co₂³⁺O_7. This excess Co³⁺ tends to destroy the ferromagnetic zig-zag chains of the ferrimagnetic structure and creates various cobalt spin clusters, leading to the inherent phase separation in the samples.     

Ferromagnetism at 300 K in spin-coated films of Co doped anatase and rutile-TiO2

Thin films of Ti_1−xCo_xO₂ (x=0 and 0.03) have been prepared on sapphire substrates by spin-on technique starting from metalorganic precursors. When heat treated in air at 550 and 700 °C, respectively, these films present pure anatase and rutile structures as shown both by X-ray diffraction and Raman spectroscopy. Optical absorption indicate a high degree of transparency in the visible region. Such films show a very small magnetic moment at 300 K. However, when the anatase and the rutile films are annealed in a vacuum of 1×10⁻⁵ Torr at 500 and 600 °C, respectively, the magnetic moment, at 300 K, is strongly enhanced reaching 0.36μ_B/Co for the anatase sample and 0.68μ_B/Co for the rutile one. The ferromagnetic Curie temperature of these samples is above 350 K.     

X-ray absorption spectroscopic and magnetic characterization of cobalt-doped zinc oxide nanocrystals prepared by the molten-salt method

The local atomic arrangement and electronic structure of the Co-doped Zn_1−xCo_xO nanocrystal have been quantitatively examined along with its magnetic properties. According to our analysis using powder X-ray diffraction, electron microscopy, and Zn K-edge X-ray absorption spectroscopy (XAS), phase-pure wurzite-structured Zn_1−xCo_xO nanocrystals have been successfully synthesized via the molten-salt method. The Co K-edge XAS analysis clearly demonstrates that all the Co²⁺ ions are substituted for the tetrahedral Zn sites of the Wurzite structure with a coordination number of 3.9 and a bond distance of 1.97 Å, ruling out the presence of magnetic impurity phase and Co-metal cluster. Magnetization measurements reveal that the present Zn_1−xCo_xO sample does not show any ferromagnetic transition down to 2 K. In this regard, we can conclude that Co-doped zinc oxide is not ferromagnetic but the previously reported ferromagnetism in this phase would be an extrinsic property.     

Room-temperature ferromagnetism in Zn1−xMnxO

In view of recent controversies on above room-temperature ferromagnetism (RTFM) in transition-metal-doped ZnO, the present paper aims to shed some light on the origin of ferromagnetism by investigating annealing effects on structure and magnetism for polycrystalline Zn_1−xMn_xO powder samples prepared by solid-state reaction method and annealed in air at different temperatures. Magnetic measurements indicate that the samples are ferromagnetic at room temperature (RTFM). Room temperature ferromagnetism has been observed in the sample annealed at a low temperature of 500 °C with a saturated magnetization (M_s) of 0.159 emu/g and a coercive force of 89 Oe. A reduction in RTFM is clearly observed in the sample annealed at 600 °C. Furthermore, the saturation magnetic moment decreases with an increase in grain size, suggesting that ferromagnetism is due to defects and/or oxygen vacancy confined to the surface of the grains. The experimental results indicate that the ferromagnetism observed in Zn_1−xMn_xO samples is intrinsic rather than associated with secondary phases.     

Modified texture and high temperature transport properties of doubly substituted BaxAgyCa2.8Co4O9 thermoelectric oxide

Doubly substituted polycrystalline compound bulk samples of Ba_xAg_yCa_2.8Co₄O₉ were prepared via citrate acid sol-gel method followed by spark plasma sintering. The phase composition, orientation, texture and high temperature electrical properties were systematically investigated. The results showed that the orientation and the texture could be modified by altering ratio of Ba to Ag. The resistivity and the Seebeck coefficient of substituted samples were decreased by decreasing Ba/Ag ratio except for that of Ba_0.1Ag_0.1Ca_2.8Co₄O₉ sample with lowest electrical resistivity (7.2 mΩ cm at 973 K), moderately high Seebeck coefficient (172 μV/K at 973 K) and improved power factor (0.42 mW/mK² at 973 K).     

The influence of hydrogen annealing on magnetism of Co-doped TiO2 films prepared by sol–gel method

Co-doped TiO₂ (Co_xTi_1−xO₂, 0.05?x?0.2) films have been prepared on Si (0 0 1) substrates by sol–gel method. When heat treated in air, Co_xTi_1−xO₂ films are non-ferromagnetic at room temperature. However, after further annealed in a flowing hydrogen atmosphere, Co_xTi_1−xO₂ films show room-temperature ferromagnetism (RTFM). Measurements of magnetization (M) vs. temperature (T), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) fail to detect Co clusters in the hydrogenated Co_0.1Ti_0.9O₂ films, suggesting that RTFM in the hydrogenated Co_0.1Ti_0.9O₂ films may be intrinsic. But, metal Co appears in the hydrogenated Co_0.2Ti_0.8O₂ films, showing that RTFM in the hydrogenated Co_0.2Ti_0.8O₂ films is as least partly due to metal Co. These results indicate that hydrogen annealing can produce room-temperature ferromagnetism in Co_xTi_1−xO₂ films, but it should be carefully designed to avoid the formation of metal Co in the hydrogenated Co_xTi_1−xO₂ films.     

Y3Al5O12 ceramic absorbers for the suppression of parasitic oscillation in high-power Nd:YAG lasers

The objective of this study was to identify a material suitable to absorb radiation at the wavelength of neodymium-doped Yttrium Aluminum Garnet (Y₃Al₅O₁₂:YAG), 1064 nm. M-(M= Sm³⁺, Co²⁺, Co³⁺, Cr³⁺, and Cr⁴⁺) doped highly transparent YAG ceramics were fabricated, and their absorption spectra were measured. Unlike Co²⁺ and Cr³⁺-doped ceramic samples, Co³⁺ and Cr⁴⁺ and Sm³⁺-doped:YAG ceramics were found to have significant absorption at 1064 nm. However, the Sm³⁺-doped YAG clearly emerged as the best candidate because it is also transparent at 808 nm, the pumping wavelength laser diode (LD), and also at most absorption bands used for flash-lamp pumping.     

The important role of Mn in the room-temperature ferromagnetism of Mn-doped GaN films

Mn-doped GaN films (Ga_1−xMn_xN) were grown on sapphire (0 0 0 1) using Laser assisted Molecular Beam Epitaxy (LMBE). High-quality nanocrystalline Ga_1−xMn_xN films with different Mn concentration were then obtained by thermal annealing treatment for 30 min in the ammonia atmosphere. Mn ions were incorporated into the wurtzite structure of the host lattice by substituting the Ga sites with Mn³⁺ due to the thermal treatment. Mn³⁺, which is confirmed by XPS analysis, is believed to be the decisive factor in the origin of room-temperature ferromagnetism. The better room-temperature ferromagnetism is given with the higher Mn³⁺ concentration. The bound magnetic polarons (BMP) theory can be used to prove our room-temperature ferromagnetic properties. The film with the maximum concentration of Mn³⁺ presents strongest ferromagnetic signal at annealing temperature 950 °C. Higher annealing temperature (such as 1150 °C) is not proper because of the second phase Mn_xGa_y formation.     

The multiferroic properties of Bi(Fe0.95Co0.05)O3 films

Bi(Fe_0.95Co_0.05)O₃ films were prepared on conductive indium tin oxide (ITO)/glass substrates by chemical solution deposition. Well saturated polarization hysteresis loop has been observed with a remnant polarization value of about 22 μC/cm² at room temperature. Weak ferromagnetism with saturation magnetization of about 3 emu/cm³ was observed at room temperature. The clear observation of both room temperature ferroelectric and ferromagnetic properties suggests the potential multiferroic applications of Bi(Fe_0.95Co_0.05)O₃.     

ZnO-Fe3O4 composite prepared by sol-gel method with H2 deoxidation

Fe doped ZnO powder samples (Fe/Zn=0.05 and 0.1) were prepared by sol-gel method with H₂ deoxidation at 450 ^°C for several hours or just heated in air at the same temperature. It was showed by vibrating sample magnetometer (VSM) that samples heat treated in H₂ could show strong ferromagnetism at room temperature while samples treated in air only show very weak magnetism. XRD using Co kα X-ray revealed that the samples heated in H₂ were not pure phase but like a granular system and the magnetism mainly results from Fe₃O₄ in samples while samples heated in air showed pure ZnO phase. Our work indicated that H₂ deoxidation treatment may be an effective technique to fabricate such magnetic semiconductor-like materials with Curie temperature higher than room temperature.     

Porous LiNi0.75Co0.25O2 microspheres prepared via a hydrothermal process as cathode material for lithium ion batteries

Porous LiNi_0.75Co_0.25O₂ microspheres are successfully prepared by a simple hydrothermal process by using H[Ni_0.75Co_0.25OOH]₃ and LiOH as starting materials in the presence of urea for the first time. The synthesized samples are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), specific surface area (S_BET), and electrochemical performance. The synthesized LiNi_0.75Co_0.25O₂ has a good electrochemical performance with an initial discharge capacity of 169.3 mA g⁻¹ and good capacity retention of 96.7% after 50 cycles at 0.2 C (25 mA g⁻¹). The electrochemical lithium ion insertion/extraction process is quite reversible even at 5 C. Furthermore, the structure in the charge-discharge process is stable and the impedance increased slowly during cycling.     

Structural, AC, and DC magnetic properties of Zn1−xCoxFe2O4

Structural, AC and DC magnetic properties of polycrystalline Zn_1−xCo_xFe₂O₄ (x=0.2, 0.4) samples sintered at various temperatures (1100-1300 °C), and various dwell times (0.2-15 h) have been investigated thoroughly. The bulk density of the Zn_0.60Co_0.40Fe₂O₄ samples increases as the sintering temperature (T_s) increases from 1100 to 1250 °C, and above 1250 °C the bulk density decreases slightly. The Zn_0.80Co_0.20Fe₂O₄ samples show similar behavior of changes to that of Zn_0.60Co_0.40Fe₂O₄ samples except that the bulk density is found to be highest at 1200 °C. The DC magnetization as a function of temperature curves show that the Zn_0.60Co_0.40Fe₂O₄ sample is ferrimagnetic at room temperature while the Zn_0.80Co_0.20Fe₂O₄ sample is paramagnetic at room temperature. The T_c of Zn_0.80Co_0.20Fe₂O₄ sample is found to be 170 K from DC magnetization measurement. Separate measurement (AC magnetization), initial permeability as a function of temperature shows that the T_c of the Zn_0.60Co_0.40Fe₂O₄ sample is 353 K. Slight variation of T_c is observed depending on sintering condition. The initial permeability for the Zn_0.60Co_0.40Fe₂O₄ composition sintered at 1250 °C is found to be maximum.     

Ammonia adsorption and decomposition on silica supported Rh nanoparticles observed by in situ attenuated total reflection infrared spectroscopy

Attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR) is applied to study NH₃, adsorbed from the gas phase, and its decomposition products, i.e. NH_x species, on Rh nanoparticles, produced by spincoating from a RhCl₃ solution in water followed by reduction. A silicon ATR crystal with a hydroxilated SiO₂ layer acts as the support for the nanoparticles. Upon exposure to NH₃ in the vacuum chamber, NH₃ adsorbed to both silica and Rh is detected (sensitivity ∼5 × 10⁻⁵ absorbance units). Interaction of the NH₃ with the silica OH groups is observed around ∼2840 cm⁻¹ in combination with peaks showing the disappearance of unperturbed OH vibrations between 3500 and 3700 cm⁻¹. In addition, NH bend vibrations at 1634 cm⁻¹ and NH stretch vibrations at 3065 and 3197 cm⁻¹ are observed for substrate temperatures between 20 and 100 °C. The latter two correspond to NH on Rh, as verified with a sample without Rh, and probably correspond to undecomposed NH₃. Moreover, they remain after evacuation, suggesting strongly bound species. For a substrate temperature of 75 and 100 °C, additional NH stretch peaks at 3354 and 3283 cm⁻¹ are observed, possibly due to NH₂ intermediates, indicating NH₃ decomposition. It is shown that ATR-FTIR can contribute to the sensitive detection of adsorption and decomposition of gaseous species on realistic planar model catalysts.     

Magnetic properties and Griffiths singularity in La0.45Sr0.55 Mn1−xCoxO3

The magnetic properties and the Griffiths singularity were investigated in Mn-site doped manganites of La_0.45Sr_0.55Mn_1−xCo_xO₃ (x=0, 0.05, 0.10 and 0.15) in this work. The parent sample La_0.45Sr_0.55MnO₃ undergoes a paramagnetic-ferromagnetic transition at T_C=290 K and a ferromagnetic-antiferromagnetic transition at T_N=191 K. The doping of Co ions enhances the ferromagnetism and suppresses the antiferromagnetism. The enhanced ferromagnetism results from the fact that the Co doping enhances the Mn³⁺-Mn⁴⁺ double-exchange interaction and induces the Co²⁺-Mn⁴⁺ ferromagnetic superexchange interaction. Detailed investigation on the magnetic behavior above T_C exhibits that the Griffiths singularity takes place in this series of Mn-site doped compounds. The correlated disorder induced by the Co ionic doping, together with the phase competition from the ferromagnetic and the antiferromagnetic interactions among Mn ions, is responsible for the Griffiths singularity.