30.6 W CW Tm3+ fiber laser of seed amplification

We use all fiber single-mode lasers as seed source, all fiber amplifiers and pump laser coupling amplifier has been experimentally investigated, respectively. The max output power of all fiber amplifier is 30.6 W, corresponding slope efficiency is 39.1%. The two setups, amplifier output laser spectrum finely holds the property of seed laser spectrum, the wavelength of output laser are both 1947.6 nm, the spectrum width is less than 2 nm as same as the wavelength of seed laser. We estimate the beam quality to be M ² = 2.42, clearly indicating nearly diffraction-limited beam propagation.     

High efficiency Tm fiber laser of seed amplification

We use all-fiber single-mode lasers as seed source, amplifiers and pump laser coupling amplifier has been experimentally investigated, respectively. The maximum output power is 10.4 W, with the slope efficiency of 54.4% when the seed laser power is 1 W, and the slope efficiency is 48.7% when the seed laser power is 2 W. The slope efficiency of this scheme is higher than that of the all-fiber amplifier. This can be explained by the loss of pump power at the splice dots. The wavelength of the fiber amplifier is 1947.6 nm, the same as the seed laser's, with a linewidth of 2 nm. We estimate the beam quality to be M² = 2.39, clearly indicating nearly diffraction-limited beam propagation.     

Active coherent beam combining of diode lasers

We have demonstrated active coherent beam combination (CBC) of up to 218 semiconductor amplifiers with 38.5?W cw output using up to eleven one-dimensional 21-element individually addressable diode amplifier arrays operating at 960?nm. The amplifier array elements are slab-coupled-optical-waveguide semiconductor amplifiers (SCOWAs) set up in a master-oscillator-power-amplifier configuration. Diffractive optical elements divide the master-oscillator beam to seed multiple arrays of SCOWAs. A SCOWA was phase actuated by adjusting the drive current to each element and controlled using a stochastic-parallel-gradient-descent (SPGD) algorithm for the active CBC. The SPGD is a hill-climbing algorithm that maximizes on-axis intensity in the far field, providing phase locking without needing a reference beam.     

Femtosecond hybrid mode-locked semiconductor laser and amplifier dynamics

We describe the generation of femtosecond high power optical pulses using hybrid passive-active mode-locking techniques. Angle stripe geometry GaAs/AlGaAs semiconductor laser amplifiers are employed in an external cavity including prisms and a stagger-tuned quantum-well saturable absorber. An identical amplifier also serves as an optical power amplifier in a stretched pulse amplification and recompression sequence. After amplification and pulse compression this laser system produces 200 fs, 160 W peak power pulses. We discuss and extend our theory, and supporting phenomenological models, of picosecond and subpicosecond optical pulse amplification in semiconductor laser amplifiers which has been successful in calculating measured spectra and time-resolved dynamics in our amplifiers. We have refined the theory to include a phenomenological model of spectral hole-burning for finite intraband thermalization time. Our calculations are consistent with an intra-band time of approximately 60 fs. This theory of large signal subpicosecond pulse amplification will be an essential tool for understanding the mode-locking dynamics of semiconductor lasers and for analysis of high speed multiple wave-length optical signal processing and transmission devices and systems based on semiconductor laser amplifiers.     

135 W average-power femtosecond pulses at 520 nm from a frequency-doubled fiber laser system

We present a high-average-power femtosecond laser system at 520 nm central wavelength. The laser system delivers sub-500 fs pulses with 135 W average power at a pulse repetition rate of 5.25 MHz. Excellent beam quality is provided by high power fiber amplifiers and maintained during frequency doubling, resulting in a beam quality factor of M2<1.2. To our knowledge, the system presented here is the highest average power green laser source generating femtosecond pulses with diffraction-limited beam quality.     

A Peltier cooled single pass amplifier for Titanium:Sapphire laser pulses

We report on a Peltier cooled single pass amplifier for high repetition rate Titanium:sapphire laser pulses. Pumped with 14 W and seeded with around 400 mW, the output reaches 1.1 W with good beam quality. This amplifier is very user-friendly, easy to maintain and set up and thus represents a device situated between more complicated liquid-nitrogen cooled amplifiers that can operate at higher pump power, and very simple near to room temperature amplifiers that can only be pumped with less power. In addition, we show the results of a finite element simulation on the temperature distribution in a liquid nitrogen cooled amplifier setup designed for highest output powers.     

激光二极管抽运的高重频高平均功率Nd:YAG激光器

搭建了一台高重复频率、高峰值功率、高平均功率的激光器. 激光器主要包括三部分: 单纵模光纤种子源、激光二极管阵列抽运的Nd:YAG再生放大器和四程放大器. 系统获得了平均功率11 W、重复频率100 Hz、脉冲能量112 mJ、脉宽500 ps–2 ns可调的激光输出, 工作波长1064 nm. 输出光束口径6.8 mm, 1.5倍衍射极限, 近场光强近平顶分布, 能量稳定性为0.72%. 关键词： 激光二极管抽运 高重复频率 高峰值功率 高平均功率     

Nd:YVO₄ amplifier for ultrafast low-power lasers

An Nd:YVO₄ amplifier consisting of two modules end pumped at 808?nm at 30?W total absorbed power has been designed for efficient, diffraction-limited amplification of ultrafast pulses from low-power seeders. We investigated amplification with a 50?mW, 7?ps Nd:YVO₄ oscillator, a 2?mW, 15?ps Yb fiber laser, and a 30?mW, 300?fs Nd:glass laser. Output power as high as 9.5?W with 8?ps pulses was achieved with the 250?MHz vanadate seeder, whereas the 20?MHz fiber laser was amplified to 6?W. The femtosecond seeder allowed extracting Fourier-limited 4?ps pulses at 7?W output power. To our knowledge, these are the shortest pulses from any Nd:YVO₄ laser device with at least 7?W output power. This suggests a novel approach to exploit the gain bandwidth of vanadate amplifiers with high output power levels. Such amplifier technology promises to offer an interesting alternative to high-power thin disk oscillators at few picoseconds duration, as well as to regenerative amplifiers with low-repetition-rate fiber seeders.     

The Nike electron-beam-pumped KrF laser amplifiers

Nike is a recently completed multikilojoule krypton-fluoride (KrF) laser that has been built to study the physics of direct-drive inertial confinement fusion. The two final amplifiers of the Nike laser are both electron-beam-pumped systems. This paper describes these two amplifiers, with an emphasis on the pulsed power. The smaller of the two has a 20×20 cm aperture, and produces an output laser beam energy in excess of 100 J. This 20 cm Amplifier uses a single 12 kJ Marx generator to inject two 300 kV, 75 kA, 140 ns flat-top electron beams into opposite sides of the laser cell. The larger amplifier in Nike has a 60×60 cm aperture, and amplifies the laser beam up to 5 W. This 60 cm amplifier has two independent electron beam systems. Each system has a 170 kT Marx generator that produces a 670 kV, 540 kA, 240 ns Bat-top electron beam. Both amplifiers are complete, fully integrated into the laser, meet the Nike system requirements, and are used routinely for laser-target experiments     

F-P半导体激光放大器弱信号机制下的增益特性研究

利用直接耦合的激光器放大器对,观察了弱信号机制下Fabry-Perot的半导体激光放大器的光放大.测量了放大器增益随放大器注入电流的变化关系,并将实验结果同理论模型相比较,发现理论和实验是一致的.把F-P放大器看作是一个光电探测器,通过测量放大器的短路光电流,得到了激光器同放大器之间的耦合效率.     

Sub-nanosecond single-frequency 10-kHz diode-pumped MOPA laser

A single-axial-mode, passively Q-switched (PQS) diode-pumped Nd:YAG laser, generating a diffraction-limited beam train of ≈40–60 μJ, ∼500-ps pulses with adjustable repetition rate in the range 1–10 kHz, was efficiently amplified by a single side-pumped Nd:YVO₄ bounce amplifier. After double-pass amplification, ≈1-MW pulse peak power with 577-ps duration and 545-μJ energy was achieved, still maintaining diffraction-limited beam performance. The average output power was 5.45 W at 10 kHz, corresponding to 13% extraction efficiency. The high brightness of this laser system seems ideal for nonlinear optics and some particular laser processing applications.     

LaB6在低压强氮气和氦气中的放电特性

研究了LaB6在1~10 Pa氮气和氦气中的直流和脉冲放电特性以及放电过程对电极的影响。结果表明，电极直径为5 mm的LaB6氦气放电管在脉冲工作状态下可以长期稳定放电。在脉冲电压为2.2 kV、脉冲宽度10 ms、频率13.3 Hz下，脉冲峰值放电电流超过120 A。氦气放电管在放电过程中，阴极表面有离子的清洗和活化作用，可以使电极的表面逸出功降低，提高放电管的发射能力和稳定性。LaB6作为气体放电电极具有寿命长、延迟时间短、放电电流大等优点，可用于重复强流脉冲气体放电的高压高速开关器件。     

High efficiency diode-pumped slab oscillator and amplifier for space-based application

The design and performance of conduction-cooled, laser diode-pumped oscillator and amplifier slab laser featuring high efficiency, high pulse energy and high beam quality for space-based application are reported. The oscillator was a diode-pumped Q-Switched Nd:YAG slab laser using unstable resonator, and the amplifiers were two zig-zag Nd:YAG slabs based on a side-pumped slab geometry. A near diffraction-limited output of 450 mJ in a 10 ns pulse at a repetition rate of 20 Hz was obtained, corresponding to an optical-to-optical conversion efficiency of over 20%.     

Single-frequency master-oscillator fiber power amplifier system emitting 20 W of power

We report a master-oscillator fiber power-amplifier system consisting of a diode-pumped monolithic nonplanar ring laser as the master oscillator and a Yb-doped large-mode-area double-clad fiber as the power amplifier. The system emits up to 20.1 W of single-frequency radiation at a wavelength of 1064 nm with diffraction-limited beam quality (M(2)相似文献   

Diffraction-limited atomic iodine photodissociation laser

A high-reliability diffraction-limited atomic iodine photodissociation laser is described. It is shown that a diffraction-limited output beam is obtained when the laser pulse is extracted before the onset of gain-medium inhomogeneities caused by non-uniform deposition of the pump radiation. No degradation of the beam focusability is observed for intensities at which the final amplifier is heavily saturated.This work supported by the United States Department of Energy.     

Multiple-Output Fiber-Ring Lasers and Amplifiers in a Hybrid CATV and ADSL Broadcasting Optical Fiber Communication System

In this article we propose two kinds of new fiber ring structure with a semiconductor optical amplifier. The first structure is a one-fiber-ring amplifier with an 8 × 8 fiber coupler and a semiconductor optical amplifier (SOA). The second fiber ring structure is a two-fiber-ring laser including an 8 × 8 fiber coupler, a 2 × 2 E/O modulator, and an SOA. The 14-output spectra of the fiber laser are measured. The gain coefficients of each port of the multiple-output-fiber-ring amplifiers are also measured. We apply these two kinds of fiber ring structures in a hybrid CATV and ADSL broadcasting optical fiber communication system. This application can develop a broadcasting system with large coverage area without using many laser diodes and optical amplifiers. The performance of such a system is also analyzed in this article.     

Multiple-Output Fiber-Ring Lasers and Amplifiers in a Hybrid CATV and ADSL Broadcasting Optical Fiber Communication System

In this article we propose two kinds of new fiber ring structure with a semiconductor optical amplifier. The first structure is a one-fiber-ring amplifier with an 8 × 8 fiber coupler and a semiconductor optical amplifier (SOA). The second fiber ring structure is a two-fiber-ring laser including an 8 × 8 fiber coupler, a 2 × 2 E/O modulator, and an SOA. The 14-output spectra of the fiber laser are measured. The gain coefficients of each port of the multiple-output-fiber-ring amplifiers are also measured. We apply these two kinds of fiber ring structures in a hybrid CATV and ADSL broadcasting optical fiber communication system. This application can develop a broadcasting system with large coverage area without using many laser diodes and optical amplifiers. The performance of such a system is also analyzed in this article.     

The 260-W coherent beam combining of two compact fibre amplifier chains

Coherent beam combining of two fibre amplifier chains with a total power of 260 W in a compact system using the stochastic parallel gradient descent (SPGD) algorithm is demonstrated. A 150 MHz linewidth fibre laser is built and introduced for high-power amplification to mitigate stimulated Brillouin scattering (SBS). Compact high-power amplifier chains are built with low power all-fibre system and high-power bulk free-optics fibre amplifiers. When the total power is about 260 W, active phase-locking of two high-power amplifiers is demonstrated using the SPGD algorithm. In closed-loop, the power in the main lobe increases 1.68 times, the visibility is increased from 0 to 0.62, and the phase residual error is less than λ/10.     

LD泵浦光纤激光放大器实现13 kW高光束质量输出

光纤耦合半导体激光器（LD）泵浦的光纤激光放大器具有体积小、功质比高、稳定性好等优点,在工业加工和军事国防等诸多领域都有着广泛且重要的应用。然而,受限于器件制作工艺水平及光纤中的受激拉曼效应和模式不稳定效应,LD泵浦的光纤激光放大器难以同时实现高功率及高亮度激光输出。为实现更高功率、更高亮度的光纤激光输出,需要结合现有的器件工艺水平并同时实现对放大器中的受激拉曼散射效应和模式不稳定效应的有效抑制。报道了基于单位自研大模场增益光纤成功实现13 kW功率、高光束质量激光输出。激光器采用主振荡功率放大结构,放大级采用单后向981 nm泵浦自研大模场增益光纤,在总泵浦功率为15 kW时,输出功率达到12.94 kW,光束质量M2因子约为2.85。通过进一步优化器件性能及光纤模式控制,有望实现更高功率、更高亮度的光纤激光输出。     

Active coherent beam combination of two high-power single-frequency nanosecond fiber amplifiers

We report on active coherent beam combining of two single-frequency nanosecond fiber amplifiers by using stochastic parallel gradient descent algorithm. Each fiber amplifier produces an average power of more than 100 W by using three-stage cascaded amplification. The two laser beams are actively phase-locked with a total average power of 215.8 W, producing ~8 ns pulses at 10 MHz repetition rate. The contrast of the far-field intensity pattern of the coherently combined beam is more than 83%.