The phase transitions and ferroelectric behavior of dense nanocrystalline BaTiO3 ceramics fabricated by pressure assisted sintering

Dense nanocrystalline BaTiO₃ ceramics with uniform grain sizes of 30 nm was obtained by pressure assisted sintering. The phase transitions were investigated by Raman scattering at temperatures ranging from −190 to 200 °C. With increasing temperature, similar to 3 μm BaTiO₃ normal ceramics, the successive phase transitions from rhombohedral to orthorhombic, orthorhombic to tetragonal, tetragonal to cubic were also observed in 30 nm BaTiO₃ ceramics. Especially, the coexistence of ferroelectric tetragonal and orthorhombic phases was found at room temperature. The ferroelectric behavior was further characterized by P-E hysteresis loop. The experimental results indicate that the critical grain size of the disappearance of ferroelectricity in nanocrystalline BaTiO₃ ceramics fabricated by pressure assisted sintering is below 30 nm.     

Dynamic pyroelectric enhancement of homogeneous ferroelectric materials

The time-dependent thermal response to a step-wise temperature increase of a ferroelectric plate of BaTiO₃ of finite thickness was determined using a combination of basic heat transfer relations to model the temperature variation in the ferroelectric as a function of time and a thermodynamic model based on a modified Landau formalism to calculate the polarization profile due to the temperature gradient. An enhancement over the static pyroelectric response was revealed, having a maximum value of −0.01 μC/cm² °C, for detector thicknesses in the range of 1 to 100 μm.     

Surface reaction characteristics at low temperature synthesis BaTiO3 particles by barium hydroxide aqueous solution and titanium tetraisopropoxide

Well-crystallized cubic phase BaTiO₃ particles were prepared by heating the mixture of barium hydroxide aqueous solution and titania derived from the hydrolysis of titanium isopropoxide (TTIP) at 328 K, 348 K or 368 K for 24 h. The morphology and size of obtained particles depended on the reaction temperature and the Ba(OH)₂/TTIP molar ratio. By the direct hydrolytic reaction of titanium tetraisopropoxide, the high surface area titania (TiO₂) was obtained. The surface adsorption characteristics of the titania particles had been studied with different electric charges OH⁻ ions or H⁺ ions. The formation mechanism and kinetics of BaTiO₃ were examined by measuring the concentration of [Ba²⁺] ions in the solution during the heating process. The experimental results showed that the heterogeneous nucleation of BaTiO₃ occurred on the titania surface, according to the Avrami's equation.     

X-ray photoelectron spectroscopic investigations on cubic BaTiO3, BaTi0.9Fe0.1O3 and Ba0.9Nd0.1TiO3 systems

X-ray photoelectron spectroscopic (XPS) studies were carried out on wet-chemically synthesized cubic BaTiO₃, Ba_0.9Nd_0.1TiO₃ and BaTi_0.9Fe_0.1O_3−δ powders. The compounds were prepared by hydrothermal and gel to crystallite conversion technique; and phases formed readily at 420 K. The phase purity of the powders was confirmed from X-ray diffractometry. Chemical state and chemical environment of the constituent elements in the compositions were examined by XPS. Ba²⁺ was found to exist in two different chemical environments in these titanates. The Ti 2p_3/2 photoelectron peak in BaTi_0.9Fe_0.1O_3−δ was found to be broadened after Fe³⁺ substitution. Any resolvable broadening was not observed distinctly in the Ti 2p peak for Ba_0.9Nd_0.1TiO₃, unsintered BaTiO₃ and BaTiO₃ annealed in hydrogen (8% H₂ + Ar) at 1000 K. The prevalence of mixed-valent titanium and iron in BaTi_0.9Fe_0.1O_3−δ composition was evident from the XPS results and was further supported by the enhanced electrical conductivity at 298-550 K for BaTi_0.9Fe_0.1O_3−δ in comparison to BaTiO₃ and Ba_0.9Nd_0.1TiO₃. Hydroxyl incorporation was facilitated by substituting Nd³⁺ in Ba-sublattice. The presence of hydroxyls was observed from the broadening of the O 1s peak in XPS studies of the compounds.     

Influence of the concentration in Fe-doped BaTiO3 on magnetoelectric couping of layered composites BaTi1−xFexO3–Tb1−yDyyFe2−z

Perovskites BaTi_1−xFe_xO₃ has been synthesized with the concentration x ranging from 0.01 to 0.02. Their transformation point of ferroelectric to paraelectric and the corresponding latent heat of the phase transformation were observed to decrease with increasing the doping level of Fe³⁺. Bonded layered composites BaTi_1−xFe_xO₃–Tb_1−yDy_yFe_2−z have been fabricated and their magnetoelectric effect has been investigated. The sample containing a layer of perovskite BaTi_0.985Fe_0.015O₃ was found to show the maximum transverse ME voltage coefficient, which is about 1422 mV Oe⁻¹ cm⁻¹ under a magnetic field of 1580 Oe, in these bilayers. Analysis shows that the Fe-doped BaTiO₃ with doping level at about 1.5% should have largest piezoelectric coefficient in these ceramics BaTi_1−xFe_xO₃.     

Theoretical investigation of the intrinsic piezoelectric properties for tetragonal BaTiO3 epitaxial films

The orientation dependences of the converse longitudinal piezoelectric constant d_33,f, and the in-plane converse piezoelectric constant e_31,f, are calculated for tetragonal barium titanate epitaxial films. The calculations demonstrate that both e_31,f and d_33,f have their maximum values along an axis close to the (1 1 1) direction of the pseudo-cubic system, which are similar to the orientation dependence results for a tetragonal BaTiO₃ single crystal. The calculated piezoelectric constants for a (1 1 1) oriented BaTiO₃ epitaxial film (e_31,f = −23 C/m², d_33,f = 124 pm/V) suggest that it is a good candidate material for lead-free MEMS applications.     

The effect of ferroelectric polarization on the interaction of water and methanol with the surface of LiNbO3(0 0 0 1)

Water and methanol temperature programmed desorption (TPD) measurements were performed on the positive (c⁺) and negative (c⁻) surfaces of poled ferroelectric lithium niobate (LiNbO₃) single crystals. The results indicate that the molecule-surface interactions are both coverage and polarization-dependent. From a comparison of the TPD spectra for the positive and negative surfaces, it is shown that the desorption temperatures of water and methanol are consistently lower on the negative surface by 15 K and 20 K, respectively. The TPD spectra were simulated using the Polanyi-Wigner equation with a coverage-dependent energy term. These calculations show that the polarization dependence of the desorption temperature is due to a difference in the zero-coverage desorption energies on the two surfaces equal to a few kJ per mole. The mechanism for the polarization effect is explored with in situ pyroelectric voltage measurements, which indicate that a surface voltage of ±2 mV develops in the LiNbO₃(0 0 0 1) samples during TPD measurements. The magnitude of the pyroelectric-induced surface charge is heating rate dependent.     

Effect of microstructure of MgO buffer layer on BaTiO3 grown on silicon substrates

MgO ultrathin films were grown on Si(1 0 0) substrates as buffer layers for the growth of ferroelectric BaTiO₃ thin films by laser molecular beam epitaxy (L-MBE). The deposition process of MgO buffer layers grown on silicon was in situ monitored by reflection high-energy electron diffraction (RHEED). The structure of BaTiO₃ films fabricated on MgO buffers was investigated by X-ray diffraction. Biaxially textured MgO was obtained at high laser energy density, but when the laser energy was lowered, MgO buffer was transformed to the form of texture with angular dispersion with the increase of the film thickness. BaTiO₃ films grown on the former buffer were completely (0 0 1) textured, while those on the latter were (0 0 1) preferred orientated. Furthermore, the fabricated MgO buffers and BaTiO₃ films had atomically smooth surface and interface. All these can reveal that the quality of textured MgO buffer is a key factor for the growth of BaTiO₃ films on silicon.     

Strongly enhanced pinning force density in YBCO–BaTiO3 nanocomposite superconductor

YBa₂Cu₃O_7−δ–BaTiO₃ (4 wt.%) (YBCO–BTO (4%)) composite bulk polycrystalline sample has been synthesized by solid state reaction method. The structure of composite sample has been investigated by X-ray diffraction and magnetization measurements were carried out using MPMS SQUID VSM. The superconducting transition temperature of the YBCO–BTO (4%) sample was similar to that of pure YBCO. The critical current density (J_c) for YBCO–BTO (4%) sample increases significantly as compared to pure YBCO sample. The enhancement of the critical current density in the YBCO–BTO (4%) sample has been attributed to the presence of BaTiO₃ nanoparticles acting as artificial pinning centres. The introduction of BaTiO₃ particles in YBCO increases pinning force density from 0.71 GN/m² to 1.41 GN/m² at 4 K and 0.33 MN/m² to 0.97 MN/m² at 77 K.     

Self-compensation characteristics of Eu ions in BaTiO3

In order to clarify whether the mixed valence of Eu²⁺/Eu³⁺ exists in a self-compensation mode in Eu-doped BaTiO₃, the site occupation and valence state of Eu ions in barium titanate were investigated by X-ray diffraction (XRD), scanning electron microscope (SEM), electron spin resonance (ESR), Raman spectroscopy (RS), and dielectric measurements. The results indicate that Eu ions may enter both Ba- and Ti-sites as Eu³⁺, forming a self-compensation mode with the amphoteric behavior. Self-compensation characteristics of Eu ions in BaTiO₃ are reflected by an expansion in unit cell volume, evolution of the 830 cm^− 1 Raman band, strong diffusion of the dielectric peak, disappearance of the Eu²⁺ ESR broad signal, and a g = 2.004 signal independent of temperature.     

A novel high-k ‘Y5V’ barium titanate ceramics co-doped with lanthanum and cerium

Structural, dielectric, and ferroelectric properties of a novel high-k ‘Y5V’ (Ba_1−xLa_x)(Ti_1−x/4−yCe_y)O₃ ceramics (where x=0.03 and y=0.05, denoted by BL3TC5) with the highest ‘Y5V’ dielectric response (ε′>10 000) among rare-earth-doped BaTiO₃ ceramics to date are investigated in detail using SEM, TEM, XRD, DSC, EPR, Raman spectroscopy (RS), temperature and frequency, electric field dependences of dielectric permittivity (ε′), and temperature and electric field dependences of ferroelectric hysteresis loops. The BL3TC5 diffusion of ferroelectric phase transition occurs around dielectric peak temperatures (T_m) near a room temperature characteristic of dielectric thermal relaxation. Powder XRD data and defect complex model were given. “Relaxor” behavior associated with an order/disorder model and formation of a solid solution were discussed. The EPR results provided the evidence of Ti vacancies as compensating for lattice defects. High-k relaxor nature of BL3TC5 is characterized by an average cubic structure with long-range lattice disordering and local polar ordering; a slow change of the ε′ (T) and P_r(T) curves around T_m; no phase transition observed by DSC; and a broad, red-shifted A₁ (TO₂) Raman phonon mode at 251 cm⁻¹ accompanying the disappearance of the “silent” mode at 305 cm⁻¹ and a clear anti-resonance effect at 126 cm⁻¹ at room temperature.     

Magnetic properties of xNi0.53Cu0.12Zn0.35Fe1.88O4+(1−x)BaTiO3 nanocomposites

The nanocrystalline Ni_0.53Cu_0.12Zn_0.35Fe_1.88O₄ and BaTiO₃ powders were prepared using Microwave-Hydrothermal (M-H) method at 160 °C/45 min. The as synthesized powders were characterized using the X-ray diffraction (XRD) and Transmission Electron Microscope (TEM). The size of the powders that were synthesized using M-H system was found to be ∼30 and ∼50 nm for ferrite phase and ferroelectric phases, respectively. The powders were densified using microwave sintering method at 900 °C/30 min. The ferrite and ferroelectric phases were observed from XRD and morphology of the composites was observed with the Scanning Electron Microscope (SEM).The magnetic hysteresis loops were recorded using the Vibrating Sample Magnetometer (VSM).The frequency dependence of real (μ′) and imaginary (μ″) parts of permeability was measured in the range of 1 MHz-1.8 GHz. The permeability decreases with an increase of BaTiO₃ content at 1 MHz. The transition temperature (T_C) of ferrite was found to be 245 °C. The T_C of composite materials decreases with an increase in BaTiO₃ content.     

Low-temperature property investigation of the lead indium-niobate-lead nickel-niobate solid solution

The complex perovskite solid solution (1−x) Pb(In_1/2Nb_1/2)O₃-(x) Pb(Ni_1/3Nb_2/3)O₃ has been successfully prepared by the Columbite precursor method. The temperature dependencies of the dielectric constant and pyroelectric coefficient were measured between −261 and 200 °C. Relaxor ferroelectric behavior has been noticed in all compositions across the solid solution. The room-temperature electrostrictive coefficient, Q₃₃, was 1.83×10⁻² C²/m⁴ for x=0.10. No room-temperature piezoelectric activity was detected; however, upon cooling to −261 °C the maximum coupling coefficients k_p=29%, k_t=11%, and k₃₃=31% were observed for the composition x=1.00.     

Binding of rare earth metal complexes with an ofloxacin derivative to bovine serum albumin and its effect on the conformation of protein

The water-soluble Pr (Ⅲ) and Nd (Ⅲ) complexes with an ofloxacin derivative have been prepared and characterized. The single-crystal X-ray diffraction showed that the Pr (III) and Nd (III) complexes have the similar molecular structure. Under physiological pH condition, the effects of [PrL(NO₃)₂(CH₃OH)](NO₃) and [NdL(NO₃)₂(CH₃OH)](NO₃) on bovine serum albumin (BSA) were examined using fluorescence spectroscopy in combination with UV-vis absorbance and circular dichroism (CD) spectra. The result reveals that the quenching mechanism of fluorescence of BSA by two complexes is a static quenching process and the number of binding sites is about 1 for both. The thermodynamic parameters (ΔH=−14.52 kJ mol⁻¹, ΔS=56.54 J mol⁻¹ K⁻¹ for [PrL(NO₃)₂(CH₃OH)](NO₃) and ΔH=−24.63 kJ mol⁻¹, ΔS=22.07 J mol⁻¹ K⁻¹ for [NdL(NO₃)₂(CH₃OH)](NO₃)) indicate that hydrophobic and electrostatic interactions are the main binding force in the complexes-BSA system. The binding average distance between complexes and BSA was obtained on the basis of Förster's theory. In addition, it was proved by the CD spectra that the BSA secondary structure was changed in the presence of complexes in an aqueous solution.     

Enhanced ferroelectric properties of (Pb0.90La0.10)Ti0.975O3 multilayered thin films prepared by RF magnetron sputtering

The (Pb_0.90La_0.10)Ti_0.975O₃/PbTiO₃ (PLT/PT), PbTiO₃/(Pb_0.90La_0.10)Ti_0.975O₃/PbTiO₃ (PT/PLT/PT) multilayered thin films with a PbO_x buffer layer were in situ deposited by RF magnetron sputtering at the substrate temperature of 600 °C. With this method, highly (1 0 0)-oriented PLT/PT and PT/PLT/PT multilayered thin films were obtained. The PbO_x buffer layer leads to the (1 0 0) orientation of the films. The dielectric, ferroelectric and pyroelectric properties of the PLT multilayered thin films were investigated. It is found that highly (1 0 0)-oriented PT/PLT/PT multilayered thin films possess higher remnant polarization 2P_r (44.1 μC/cm²) and better pyroelectric coefficient at room temperature p (p = 2.425 × 10⁻⁸ C/cm² K) than these of PLT and PLT/PT thin films. These results indicate that the design of the PT/PLT/PT multilayered thin films with a PbO_x buffer layer should be an effective way to enhance the dielectric, ferroelectric and pyroelectric properties. The mechanism of the enhanced ferroelectric properties was also discussed.     

CW-cavity ring down spectroscopy of the ozone molecule in the 6625-6830 cm region

The absorption spectrum of ozone, ¹⁶O₃, has been recorded by CW-cavity ring down spectroscopy in the 6625-6830 cm⁻¹ region. The typical sensitivity of these recordings (α_min ∼ 3 × 10⁻¹⁰ cm⁻¹) allows observing very weak transitions with intensity down to 2 × 10⁻²⁸ cm/molecule. 483 and 299 transitions have been assigned to the 2ν₁ + 3ν₂ + 3ν₃A-type band and to the 2ν₁ + 4ν₂ + 2ν₃B-type band, respectively, which are the highest frequency bands of ozone recorded so far under high resolution. Rovibrational transitions with J and K_a values up to 46 and 12, respectively, could be assigned. Despite well-known difficulties to correctly reproduce the energy levels not far from the dissociation limit, it was possible to determine the parameters of an effective Hamiltonian which includes six vibrational states, four of them being dark states. The line positions analysis led to an rms deviation of 8.5 × 10⁻³ cm⁻¹ while the experimental line intensities could be satisfactorily reproduced. Additional experiments in the 5970-6021 cm⁻¹ region allows detecting the (233) ← (010) hot band reaching the same upper state as the preceding cold band. From the effective parameters of the (233) state just determined and those of the (010) level available in the literature, 329 transitions could be assigned and used for a further refinement of the rovibrational parameters of the effective Hamiltonian leading to a value of 7.6 × 10⁻³ cm⁻¹ for the global rms deviation. The complete list of the experimentally determined rovibrational energy levels of the (233), (242), and (520) states is given. The determined effective Hamiltonian and transition moment operators allowed calculating a line list (intensity cut off of 10⁻²⁸ cm/molecule at 296 K), available as Supplementary material for the 6590-6860 and 5916-6021 cm⁻¹ regions. The integrated band strength values are 1.75 × 10⁻²⁴ and 4.78 × 10⁻²⁵ cm/molecule at 296 K for the 2ν₁ + 3ν₂ + 3ν₃A-type band and to the 2ν₁ + 4ν₂ + 2ν₃B-type band, respectively, while the band intensity value of the (233) ← (010) is estimated to be 1.03 × 10⁻²⁴ cm/molecule.     

Ethylene adsorption on the Pt-Cu bimetallic catalysts. Density functional theory cluster study

The adsorption of ethylene on Cu₁₂Pt₂ clusters has been studied within the density functional theory (DFT) approach to understand the high ethylene selectivity of Cu-rich Pt-Cu catalyst particles in the reaction of hydrogen-assisted 1,2-dichloroethane dechlorination. The structural parameters for Cu₁₂Pt₂ clusters with D_4h, D_2d, and C_3v symmetry have been calculated. The relative stability of the isomeric Cu₁₂Pt₂ clusters follows the order: C_3v > D_2d > D_4h. Each isomer has an active site for ethylene adsorption that consists of a single Pt atom surrounded by Cu atoms. The interaction of ethylene with the active site yields a π-C₂H₄ adsorption complex. The strongest π-C₂H₄ complex forms with the cluster of C_3v symmetry; the bonding energy, ΔE_π(C₂H₄), is −15.6 kcal mol⁻¹. The bonding energies for the π-C₂H₄ complex with Cu₁₄ and Pt₁₄ clusters are −6.5 and −18.8 kcal mol⁻¹, respectively.The addition of Pt to Cu modifies the valence spd-band of the cluster as compared to a Cu₁₄ cluster. The DOS near the Fermi level increases when C₂H₄ adsorbs on the Cu₁₂Pt₂ cluster. As well, the center of the d-band shifts toward lower binding energies. Ethylene adsorption also induces a number of states below the d-band. These states correspond to those of gas-phase C₂H₄.The vibrational frequencies of C₂H₄ adsorbed on the clusters of D_4h and C_3v symmetry have been calculated. The phonon vibrations occur below 250 cm⁻¹. The intense bands around 200 cm⁻¹ are attributed to stretching vibrations of the Pt-Cu bonds normal to the cluster surface. The stretching vibrations of the Pt-C bonds depend on the local structure of the active site: ν_s(Pt-C) = 268 cm⁻¹ and ν_as(Pt-C) = 357 cm⁻¹ for the cluster of the D_4h symmetry; ν_s(Pt-C) = 335 cm⁻¹ and ν_as(Pt-C) = 397 cm⁻¹ for the cluster of the C_3v symmetry. Bands in the range of 800-3100 cm⁻¹ are attributed to vibrations of the adsorbed C₂H₄ molecule. The signature frequencies of the π-C₂H₄ adsorption complex are the δ_s(CH₂) deformation vibration at ∼1200 cm⁻¹ and the ν(C-C) stretching vibration at ∼1500 cm⁻¹. These vibration are absent for di-σ-C₂H₄ adsorption complexes.     

H2 reactivity on the surfaces of In and Sn at 298 K

The reactivity of H₂ gas with the In and Sn surfaces was quantitatively measured by a volumetric method at pressures ranging from 10⁻⁷ to 10⁻² Pa at 298 K. Significant enhancement of H₂ reactivity was observed when O₂ or H₂O preadsorbed on the surface of In and Sn before H₂ exposure. The formation of the oxygen deficient SnO_2−x and In₂O_3−z in the surface layers is proposed as a reason for such a facilitating the H₂ dissociation and resulting in the enhancement of the H₂ reactivity at 298 K.     

Preparation and characterization of carbons for the retention of halogens in the condenser vacuum system of a thermonuclear plant

Activated carbons were prepared by air and carbon dioxide activation, from almond tree pruning, with the aim of obtaining carbons that reproduce the textural and mechanical properties of the carbons currently used in the filtering system of the condenser vacuum installation of a Thermonuclear Plant (CNA; Central Nuclear de Almaraz in Caceres, Spain), produced from coconut shell. The variables studied in non-catalytic gasification series with air were the temperature (215-270 °C) and the time (1-16 h) and the influence of the addition of one catalyst (Co) and the time (1-2 h) in catalytic gasification. In the case of activation with CO₂, the influence of the temperature (700-950 °C) and the time (1-8 h) was studied. The resulting carbons were characterized in terms of their BET surface, porosity, and pore size distribution. The N₂ adsorption isotherms at 77 K for both series showed a type I behaviour, typical of microporous materials. The isotherms showed that with both gasificant agents the temperature rise produced an increase in the carbon porosity. With regards to the activation time, a positive effect on the N₂ adsorbed volume on the carbons was observed. The best carbons of each series, as well as the CNA (carbon currently used in the CNA), were characterized by mercury porosimetry and iodine solution adsorption isotherms. The results obtained allowed to state that several of the carbons produced had characteristics similar to the carbon that is target of reproduction (which has S_BET of 741 m² g⁻¹, V_mi of 0.39 cm³ g⁻¹ and a iodine retention capacity of 429.3 mg g⁻¹): carbon C (gasification with CO₂ at 850 °C during 1 h), with S_BET of 523 m² g⁻¹, V_mi of 0.33 cm³ g⁻¹ and a iodine retention capacity of 402.5 mg g⁻¹, and carbon D (gasification with CO₂ at 900 °C during 1 h), whose S_BET is 672 m² g⁻¹, V_mi is 0.28 cm³ g⁻¹ and has a iodine retention capacity of 345.2 mg g⁻¹.     

Effect of ferroelectric polarization on the adsorption and reaction of ethanol on BaTiO3

The effect of ferroelectric polarization on the adsorption and reaction of ethanol on BaTiO₃ was studied using temperature-programmed desorption (TPD). Consistent with previous studies for methanol, the reactive sticking coefficient for ethanol on the surfaces of the ferroelectric, tetragonal phase of BaTiO₃ was found to be dependent on the orientation of the ferroelectric domains with a higher sticking coefficient on the c⁺ surface relative to the c⁻ surface. TPD peak shapes and the relative product yields were also found to be polarization dependent suggesting that ferroelectric polarization may affect the intrinsic reactivity of the surface.